How to connect my i phone to wireless printer

how to connect my i phone to wireless printer

You would have to have one of the few HP printers that support airprint:
iOS: AirPrint 101
Or you could find an app that provides this feature.

Similar Messages

  • How to connect my ipad mini to wireless printer

    Could someone tell me how to connect my ipad mini to my AirPrint printer

    If it says there is no sim card installed it either can't find one physcially, or the card moved and lost contact or has failed.  A new sim card can be obtained form your Mum's cell/mobile carrier if needed easily.
    However this is irrelevant to whether or not the iPad can join a Wifi network.  Its 2 different things.
    For now ignore the Sim card message and just try to connect to her Wifi network.  It is independent and should function regarldess of the sim card status.

  • How to connect my macbook to a wireless printer?

    My printer has connected to WiFi no problem but I cannot seem to find the printer when in system preferences "add printer"...Please help!

    Hey sharminw,
    Have you installed the printer drivers for your printer? If you already did, and if you are connected to your wireless internet through your computer, you should be able to see your printer under "add printer."
    I noticed I couldn't install a wifi printer through "add printer" unless I had the drivers installed.
    Hope this helps.

  • How to connect my iphone to a wireless speaker

    how to connect my iphone to a wireless speaker logitech Z515

    Are you trying to connect over Bluetooth?
    Matt
    Message was edited by: Matthew Morgan

  • HT3500 How do I connect my iPad to my wireless printer?

    How do I connect my iPad to my wireless printer?

    Your iPad should be able to print directly to your printer if it is an AirPrint compatible model.
    Check this Apple support document to see if your printer is compatible.
    http://support.apple.com/kb/HT4356
    Post back on your findings.

  • How do i set my hp310 to wirelessly print?

    how do i set my hp310 to wirelessly print?

    Hi,
    It's cheaper to buy a new one.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Do MG 3120 and MG 6220 work with Android phones for wireless printing?

    Hi People, I just joined this forum and hopefully some of you can tell me if the MG 6220 or MG3120 printers work with Android phones to wireless print from the phone.  I looked at the specs from the Cannon website on both machines and could not find anything to answer my question.  Maybe I missed it but I figured the Cannon users can point me in right direction.  I love my Cannon camera and I am seriously looking at the MG series of printers for home to replace my HP printer that has lost its mojo.
    Thanks ya all!
    Solved!
    Go to Solution.

    Hello KensingtonCat.
    We have an Android app for printing photos.  The Easy PhotoPrint app is available from the Android Market or Google Play and will allow you to print photos from most Android devices with the MG3120 and MG6220.
    More information can be found at the following link:
    https://play.google.com/store/apps/details?id=jp.co.canon.bsd.android.aepp.activity&hl=en
    Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

  • I need step by step way of connecting my iPad to my wireless printer?

    I need help connecting my iPad to my wireless printer?

    Add to Templeton's post: Never hurts to power down the iPad, count to 10, then turn it on again.  When my iPad loses touch with our printer, we power cycle the iPad, and that normally fixes the issue.  Also review the link in Templeton's post.

  • Is there a way to print texts/messages older than 90 days from phone without wireless printer?

    Is there a way to print texts/messages older than 90 days from phone without wireless printer?

    thanks for the reply....but forwarding to my email  - well, there were too many that I wanted printed.  But do appreciate your answering. 

  • How to connect WPS (BlackBerry phone) on wi-fi with airport express ?

    My boyfriend (not sold to Apple yet) wants to connect his BlackBerry phone on our wi-fi network.  Because it is WPS, it detects the network but I we don't know how to connect.  We need help !!!

    If I were to connect the AirPort Extreme to my modem (DPC3825) via an Ethernet cable and then (wirelessly) connect my new iMac to the netowrk, would I receive 802.11ac or just b/g/n still?
    802.11ac would be received by the iMac if it connected to the AirPort Extreme wireless signal....and....the iMac was in close proximity to the AirPort Extreme.
    802.11ac uses the 5 GHz frequency, and these signals only work well then the router and computer are in the same room or have a line-of-sight relationship  to each other, or very close to that ideal.
    In addition, when I connect the AirPort Extreme to my modem, will it create two networks
    The AirPort Extreme will create a network with two bands or frequencies.....one  2.4 GHz for "b", "g" and "n" wireless devices and another band, the 5 GHz signal for "n" and "ac" devices.
    If you assign the same name to  the AirPort Extreme network that you use for your existing network, and both routers are using the same wireless security settings and password, then everything will act like one "big" network.
    If you assign a different name to the AirPort Extreme wireless network, then you will have two different networks....one produced by your existing router and the other produced by the AirPort Extreme.
    If you move from one area to another, you will have to log off of one network and log back onto the other network.

  • How to connect my I phone 5 to my apple TV

    Im trying to connect my I phone 5 to my apple TV!!! Thanks guys!!! So wish apple had a TV comming out that would be awsome!!!!!

    Welcome to the Apple Community.
    Exactly how are you trying to connect it and what problems are you having doing so.

  • How to Connect Airport Express to Existing Wireless Network (Client Mode)

    I am posting this for everyone tearing their hair out trying to connect the Airport Express to your own existing home wireless network. After spending 2 hours last night installing this on my father-in-law's home network, I hope to be able to save someone else the agony we went through.
    So here's the situation:
    Say you already have your own home network set up, and all you want is to be able to use AirTunes to play music off iTunes into your speaker system. And, you don't need the printer sharing capability nor creation of another wireless network (2 of the features of Airport Express). Then this solution is for you - read on.
    Unfortunately, Apple's user manual is very unclear how to connect Airport Express to your own network. When you look at the picture diagram they provide, they show Airport Express picking up its signal from another Apple-oriented base. This can make you think you need to buy another piece of hardware to make it work. DON'T If you read through the manual, the Support section here, etc., you will hear lots of talk about "Client Mode" - and that this is the only way to get it to work. Nice - but no one really tells you how to set up the Airport in client mode.
    Do yourself a favor, toss that user manual aside and run these steps.
    (Note: These directions assume your DSL/Cable Modem is hooked up to a wireless router or acts as its own wireless router)
    1. Get a cat5 Ethernet cable (anything but an orange cable - that's a crossover cable) like you would use to connect your PC to your router to pick up the Internet.
    2. Connect the Ethernet cable to the router on one end, and to the Airport Express unit on the other end.
    3. Plug in your Airport Express unit to the wall (this will not necessarily become its permanent location - you will be able to move it later). The light will glow solid Amber for about 30-45 seconds while it starts up, then blink Amber. At this point, the unit is ready to operate.
    4. Install the CD to the PC where your iTunes music is stored. This should be painless. Once you open the program, it should detect the Airport unit.
    5. At this point, the on-screen wizard will present you with your options, and walk you through the setup. This is much like the user manual describes - and you should be good to go form here forward.
    Some pointers:
    - When asked if you want to create a new network, join an existing network, or connect via Ethernet, choose the middle option for joining an existing network. You will need to know the name of your network, the password to connect to the network (if present), and the type of encryption used on the network (e.g. WEP, WPA, etc.). Side note, WPA is recommended, as it is a higher level of security than WEP. You will be able to configure the Airport Express unit to automatically login to your network.
    - I would recommend, when creating a password for the Airport Express unit, use the same password as your network, to avoid confusion.
    6. The very last step will ask you to save the settings to the Airport Express. Here's the kicker - when you save the settings, you are TRICKING the Airport Express into no longer acting as a network broadcaster, but instead being a "slave" to your own network. What do I mean? You will lose the connection from your PC to the Airport Express - an error message will pop up telling you the unit can no longer be found. While you might think you did something wrong, you actually were successful!
    7. Unplug your Airport Express, and disconnect the Ethernet cable from your router and the Airport unit. This will no longer be needed.
    8. Go to your desired location where you want to plug in your Airport Express unit. Before plugging it in, connect your Audio cable from the Airport Express to your audio receiver. Once that is connected, then plug in the Airport Express unit. The light will glow solid Amber for 30-45 seconds while it loads, and then will blink Amber for a brief period of time before turning solid GREEN. When this happens, you have successfully connected the Airport Express to your home network!
    9. Go back to your PC with iTunes. Open the Airport software - you should now have a listing for your Airport Express unit in the upper left. Click on this, and the wizard will guide you through connecting - you will need the password you created for the unit. You only need to go through this wizard once, and when finished, the software will tell you that can now use iTunes with your Airport unit.
    10. Open iTunes. On the lower right, you will see a dropdown for Speakers, and it should be defaulted to My Computer. Click on that drop-down, and you will see the name of your Airport unit. Click on that name, and now your music will broadcast to the Airport unit!
    11. Play a song in iTunes. Go to your audio receiver, and connect it to the channel for your external connection to the Airport Express unit. You should hear your music from iTunes. CONGRATULATIONS! =)
    I hope these instructions were helpful - I am happy to answer any questions, so feel free to contact me, *******************@*****.**.
    <Edited by Moderator>

    Thanks for the detailed directions. You are absolutely correct in stating that people should toss the user manual; it's pretty worthless. I have had a problem setting up my new Airport Express as I have described in an earlier post - http://discussions.apple.com/thread.jspa?threadID=1839873&tstart=45
    One quick question - does using your setup process set the AE up as part of a distributed network where the AE is acting as a wireless router where it is extending the range of your network? Or, is it simply a wireless connection to your stereo for iTunes? I am interested in having both, since my AE will be at the other end of the house from the main wireless router.
    Thanks

  • How do connect mt iPod to my wireless/Bluetooth hp printer

    How can I connect my ipad2 to my wireless/Bluetooth HP printer?

    Please go on the iPod Touch forum - this is for iPod Classic

  • How do I connect my iPad to my wireless printer

    How do I connect my wireless printer to my I pad

    iOS devices can only print directly to AirPrint printers. All AirPrint printers are wireless but not all wireless printers are capable of using AirPrint.
    To print directly from an iPad / iPhone you will need an AirPrint compatible printer or another device to act as a print server. That can be a Mac computer running Printopia ($19.95 with free trial) or handyPrint (donation - supported). The Mac must be "on" but may be asleep for them to work. Equivalent PC options may exist but you're on your own finding them.
    You can also buy this standalone print server:
    http://www.lantronix.com/it-management/xprintserver/xprintserver.html
    The xPrintServer Home Edition will support a directly connected USB printer. The Network Edition will support any network printer.
    These options enable you to use any printer available to your Mac, even older ones that may predate AirPrint by decades.
    Otherwise you will need to buy an AirPrint printer or multifunction device.

  • How to connect time capsule to existing wireless router

    Hi
    I am struggling to set up my time capsule is it possible to connect it to my existing wireless router or does the time capsule have to replace it as I have tried to do that but I cannot get a connection or signal to the WAN port?
    I have the set up instructions but its not helping I am a complete novice at this.
    Any help or links much appreciated

    Yes you can.
    Just plug the TC into one of the Ethernet ports on your router. WAN port on the TC.
    Before you do that, set the TC up to be in 'bridge mode' in AirPort Utility.

Maybe you are looking for

  • Sales Analysis Report based on Supplier-wise

    Hi Experts, My client requirement is ,We are into trading so , we want a Sales analysis report based on Supplier-wise. like, Selection critieria is 1)Supllier name 2)From and To date. Heading are Item name     Sales UoM    Jan(quantity)   Feb(quaniti

  • Duplicate whole row, change account number

    Hi, I would like to duplicate the whole row in Journal Entry and then change the account number. However, when I changed the account number, the content of the other fields was cleared. i,e. All duplicated contents were cleared. Is there any way to c

  • Time Data Integration with peopleSoft

    Hi, Employees enter their time in SAP Portal. Once these times are approved, these need to be moved in to PeopleSoft. Presently there are complex interfaces for the process. Management has decided to redesign the interfaces. Can somebody give me an o

  • Where do you receive your vertification code for your apple id?

    Where do you receive your vertification code for your apple id?

  • Internal Order Status Management

    Hi All,          I'm having a query regarding Status Management of Internal Orders.We have created a User Status starting from 10 till 50  to go alongwith the system status. We want a scenario wherein the user cannot change the status from 10 to 20 t