How to connect serial or usb or parallel port

telll me how to connect our application with serial port and how to detect weather the usb is connected or not

Without spending too much time looking at the documentation, from using previous similar transducers, the primary two connections you are concerned with are the "+output" and the "ground". The other connections are also important, but aren't directly the concern of the Data Acquisition Hardware. The "+output" produces a variable dc voltage relative to the "ground" input that is a product of the applied pressure, with the maximum output voltage, as shown on the chart, indicating maximum pressure. So you would connect those, through a suitably shielded, moderately short length, wire to the "DAQ" analog input. You will also have to supply the transducer with it's required + supply voltage at pin 2 "vs", and the power supplie's negative to the ground. There are whitepapers on this NI site about connecting to data acquistion hardware and I strongly suggest reading them a couple of times as well as anything online you can find. Writing the DAQ software, in LabVIEW or whatever, can be trivial compared to making the correct, low noise, connections to sensor hardware.
I didn't read how the offset adjustment signal is produced or its use, figure it is designed to allow you to "tune out" some signal offset caused by differences between sensors of a type (they will not all have the same "fullscale output" as indicated in the chart).
As you proceed, please keep asking.
Putnam
Certified LabVIEW Developer
Senior Test Engineer
Currently using LV 6.1-LabVIEW 2012, RT8.5
LabVIEW Champion

Similar Messages

  • Windows XP connecting Peer-to-Peer to Windows 7 with HP LJ 4000 through USB-2-Parallel port

    I am running a Peer-to-Peer network and cannot connect my Windows XP computer over the network the 'quasi-server' running Windows 7 that has a connected HP LaserJet 4000 printer connected via a USB-2-Parallel port.  The HP LJ4000 works just fine from the Windows 7 box (and serves ONLY as a backup printer) but connecting from either Windows XP PRO boxes will not work.  
    I have tried opening the Windows 7 Printers window and then updating the printer drivers, like it says it will, and that fails as well.
    ANY suggestions would be appreciated!
    Thank you, 
    Brett W. Sabio
    Regards,
    Brett W. Sabio, CPA-PFA

    Hi,
    You need something like this:
      http://www.shopbot.com.au/pp-belkin-usb-parallel-printer-adapter-f5u002-price-106075.html
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • I have a PowerPC G4 w/OSX 10.4.11 and a HP laserjet 4 connected with a USB to parallel cable,  I cannot get it to print, how do I fix it ?

    I have a PowerPC G4 w/OSX 10.4.11 and a HP laserjet 4 connected with a USB to parallel cable,  I cannot get it to print, how do I fix it ?

    This forum is for questions about Apple Remote Desktop, Apple's software for managing networked Macs. You'll be more likely to get help with this question if you ask it in the Mac OS X 10.4 forum:
    https://discussions.apple.com/community/mac_os/mac_os_x_v10.4_tiger
    Regards.

  • USB to Parallel Port connector plug for printer

    Hi
    I'm trying to get an old IBM laster printer (4019) to work with an ibook G4--I have downloaded the Gutenprint driver which is supposedly compatable but now I need advice on adapting cables for printers. I was going to buy a Sabrent USB to Parallel port connector but saw in the feedback that many people weer unhappy with it. Could somebody suggest the best USB to Parallel port connecting cable for me and where to order it? thanks very much.

    Hi Derek,
    maybe this is a better one: http://www.keyspan.com/products/usb/up6c/homepage.spml
    I don't have any need for this, so I can't provide any review of it.
    Regards
    Stefan

  • How can I do to communicate to parallel port using labview 5.0 and NT ?

    I am trying to write and read from parallel port using Labview 5.0. It does not work with NT.
    How can I do to communicate to parallel port using labview 5.0 and NT ?
    Thank you in advance.
    Regards,

    If you are trying to use In/Out port functions that come with LabVIEW they will not work with NT. I think the AccessHW file at the following link will fix that problem:
    http://zone.ni.com/devzone/explprog.nsf/6c163603265406328625682a006ed37d/49664743ded6f1da862564bc004e3a7f?OpenDocument
    Try also this link:
    http://zone.ni.com/devzone/conceptd.nsf/2d17d611efb58b22862567a9006ffe76/0989d3d9dafae64e8625680400679736?OpenDocument
    and do some searchs at NI.com for parallel port, you should find some more usefull info.
    Good luck
    Brian

  • Connecting a HP LaserJet 4000 parallel port to Windows 7 USB port

    I have been using a HP LaserJet 4000 via a parallel port for years on a variety of machines / Operating systems without issue. However, having purchased a new Laptop (Windows 7  64bit), there is no parallel port (unsurprisingly). So the question is 'How do I connect my legacy parallel printer to the USB port ?
    Regards
    John Bennett

    Hi,
    You need something like this:
      http://www.shopbot.com.au/pp-belkin-usb-parallel-printer-adapter-f5u002-price-106075.html
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How to connect to a usb cam through acrobat api??

    I have deveopled a plugin for acrobat...and want to initiate a usb cam through my plugin...is there any method available in the api to detect or connect to a usb cam????If yes please explain how to do so...

    ...is there any method available in the api to detect or connect to a usb cam????
    No. You may look at the apis of your operating system.

  • How to connect to the USB printer

    I connect a USB printer to the USB port of my Airport Extreme.  Can someone help advise the procedure for the computers in the network to connect to the USB printer.  Thanks!

    Unfortunately, not all USB printers are compatible with AirPort base stations. In addition, the  AirPort's USB port does not support the "advanced" printer functions, like scanning, copying or faxing, of multi-function printers. 
    To see if your printer is compatible, take a look at thisiFelix Unofficial AirPort Printer Compatibility link. If your printer isn't listed, it doesn't necessarily mean it won't work, but simply that it has not been verified. iFelix also provides the following workaround for printers not on the list that would certainly be worth a try.
    Also you can try this Apple Tech Support article to see if it will help: Printer troubleshooting for AirPort Base Stations and Time Capsule
    Finally, check out this IBM support article to see if your printer is listed as having a Postscript or PCL3 interface. If it does, then it will most likely work with the AirPort's USB port. Printers that use the "HP LIDIL" interface must be connected to a computer directly and will not work.

  • Usb to parallel port converter

    Hello all
    I am having usb to 36 pin parallel port converter and i try to communicate with that to run a stepper motor.
    how can i communicate with that.?  I plan to use visa function for that, what are all the pins i have to be grounded. (Can i use visa write funtion for that?)
    i have read in forums for IEEE1284 standard i have to ground pin 11 and pin 12.
    And i dont know one more thing, in max i can see only COM ports without any problem and i cannot see any usb port in that.
    Is COM port and usb port are same.?

    This may make things more difficult. You can try if outport to the port addresses hex378 or hex278 works, but probably it doesn't. You may try to find out if your device has a different port address.
    A PCMCIA parallel port normally works like a standard one. with the 378 or 278 port address.
    Cheers
    Edgar

  • How should I develop Level Controller using Parallel port(Printer port)

    I need to develop a level controller using parallel port of my computer with a third party Data Acquisition Device.  Is it possible to do it with In and out port vi in labView 7.1. Please guide me how can should I configure these Vis to write control data and then receive level transmitteed data through parallel Port(Printer port). My third party DAQ has two analog input channel and one analog output channel.  

    Dennis Knuston
    I have uploded the details of that  third party daq in another thread please see that and tell wether this type of daq requires driver software
    http://forums.ni.com/t5/Multifunction-DAQ/Parallel-port-based-daq-and-drivers/m-p/1819997

  • JTAG Digital Waveform transfered using USB or parallel port ?

    Hi all
    I was wondering if there is a way to send JTAG Digital Waveforms generated by LabVIEW into a parallel port or USB port.  I know that there is a way to use DAQmx devices with JTAG Digital Waveforms where DAQmx drivers take JTAG Digital Waveforms and transfer that into physical signals which is then send to UUT.  I really am in a need to try to mimic whatever a DAQmx can do to make that happen with a parallel port or usb port. I would really appreciate if you can help me it is very urgent.
    Thanks

    Hi Cristopher
    I do really appreciate for a quick response. I am full aware of the fact that NI products for digital waveform generation will do the job, plus it is easier to implement them. However my goal is to use an inexpensive device that can generate external timing and my JTAG library and make .exe files from my final code and distribute that setup for several computers in factory. So buying several digital waveform generators from NI for each PC in factory will be a very expensive option. I think now you have a better picture why I am trying to find another inexpensive way to implement these digital waveforms using JTAG library. It would be ideal if I can use parallel port with some external timing to do the trick but I am really not sure where to start. Cirstopher I would really appreciate if you can come up with any suggestions in regards to this problem that I am having.
    Thanks again.

  • How counter and frecuency measuremen​t using parallel port?

    Estoy ingresando un tren de pulsos por una linea del
    puerto paralelo y necesito detectar los flancos para poder incrementar un contador por cada pulso de entrada.

    Dear, codeman2:
    I thank for infinitely its advice to him. But I must work with the parallel port because one is a didactic project and do not have average acquiring the acquisition boards. In addition to be in a stage of study and investigation all inverted time will bring futures benefits. Thank you very much by his interest and it excuses my ingles.

  • How to connect an MTN usb rotator to an Apple MacBook Pro 13'3

    How do i go about connecting my Apple MacBook Pro 13'3 to the interent with an "Huawei Mobile Broadband E367 HSPA+ USB ROTATOR" on the MTN Network

    If your USB port is working now, you didn't damage it and have nothing to worry about.
    The behavior you saw in your bus-powered Fujitsu drive is normal for a drive that needs more power than the USB port can provide.
    If your USB ports ever do shut down, resetting the SMC may bring them back online again quickly and easily.

  • How to Connect LS CAN (USB-8472) to Single-Wir​e CAN device?

    In the post of http://forums.ni.com/ni/board/message?board.id=30&​message.id=216&requireLogin=False , NI Engineer said that
    “It is possible to use our Low-Speed CAN boards in
    a single-wire mode. However, the board will give CAN warnings. So, the
    control program may have to ignore certain CAN warnings.
    Randy Solomonson
    Application Engineer
    National Instruments”
    But I can't see the detail connection and software settings in that post.
     How can I use LS CAN to communicate with single-wire CAN (such as GMLAN)? Should I make some additional settings in my LabVIEW program?
    帖子被hmqi2002在 07-09-2009 04:07 AM
    时编辑过了

    In the post of http://forums.ni.com/ni/board/message?board.id=30&​message.id=216&requireLogin=False , NI Engineer said that
    “It is possible to use our Low-Speed CAN boards in
    a single-wire mode. However, the board will give CAN warnings. So, the
    control program may have to ignore certain CAN warnings.
    Randy Solomonson
    Application Engineer
    National Instruments”
    But I can't see the detail connection and software settings in that post.
     How can I use LS CAN to communicate with single-wire CAN (such as GMLAN)? Should I make some additional settings in my LabVIEW program?
    帖子被hmqi2002在 07-09-2009 04:07 AM
    时编辑过了

  • How to connect the Wimax Usb stick ,

    HI
    I have wimaxx usb stick I can not access to internet.softwire not responding .
    please help me.
    Thank you

    According to this page:
    http://www.clear.com/support/download/usb/wimax-2-usb-adapter
    There is a beta driver for Lion.  Beta means a guinea pig application, where you are the guinea pig.    So if it doesn't work, you should report to them what's wrong.

Maybe you are looking for

  • How to make CS6 Camera Raw process in 16 bit mode by default

    I just received my Adobe Photoshop CS6 and downloaded the current updates. I have noticed that when I download raw images into Bridge the Metadata indicates that the images have a '16 Bit Depth' but when I open the images in Camera Raw the 'Image Mod

  • JCo Server Load Balancing

    We have created a JCo Server interface using RFC modules in SAP to communicate with an external web based system.  The SAP system calls the external application via tRFC and qRFC as needed from the business transaction.  We have achieved high through

  • Apps n fonts looks larger on 6 plus

    Hi, I set up my iPhone 6 plus by restoring the iPhone 5s backup through iCloud. Everything worked fast and smooth – all done in less than half n hr and I got a perfect clone of 5s on iPhone 6 plus. And I didn't set the system default display to be 'z

  • Screen shows apple only after tring to updated wont turn off or change

    Tried to update Ipod 4 and restore as got screen with plug in to I-tune, went thru update but then froze with th apple on screen of I-Pod.  Now it wont reset wont turn on or off or be seen in I tunes.  Wont charge either Any help?

  • Sales document 187000001 does not exist

    Sales document 187000001 does not exist Message no. VB001 Can you please advice why this error occurs? I am creating sales order (RE) type with reference to actual sales order, during reversal process all the docuemnt generating but still not showing