How to connect the wrt120n to android

My mother in law bought my daughter a impression android tablet for Christmas it connects fine at public hotspots but I can not get it to connect to our wrt120n router at home. I have tried everything I know to add it. It asks for the password then says getting IP address then disconnects. What can I do to fix this besides pull my hair out.

You can try the following:
# Open up the browser and on the address bar type 192.168.1.1 that will open up the Router setup page.
# Then Click on wireless Tab select Channel Width to 20 MHz only and Channel to 6, 9, and 11. Click Save Settings.
# Click on wireless Security tab and lower down the security level of the wireless.
#Adjust the following advanced wireless settings:
~~ Lower the beacon interval from 100 to 50
~~ Lower the fragmentation threshold from 2346 to 2306
~~ Lower the RTS threshold from 2347 to 2304
After doing the following settings then try to connect the android tablet and check the connectivity..

Similar Messages

  • My ipad 3 is frozen on the plug into itunes page. I have tried to follow advice I have found on these pages but I don't know how to connect the ipad to my mac (there is no usb port on an ipad). If anyone could help it would be appreciated.

    My ipad 3 is frozen on the plug into itunes page - it won't turn off or on - just stuck. I have tried to follow advice I have found on these pages but I don't know how to connect the ipad to my mac (the advice is to connect ipad to mac and there is no usb port on an ipad). If anyone could help it would be appreciated. Going nuts.

    I think you should probably also read the iPad User Guide. You didn't say what version of iOS your iPad is running, so here's the links to both the iOS 6 and iOS 7 (PDF) versions:
    iPad User Guide for iOS 6
    iPad User Guide for iOS 7

  • How to connect an apple tv to an enterprise network with a username and a password?   I need to use it over my university's wifi. theres no option to enter username and password. how to connect the apple tv to such enterprise network?

    How to connect an apple tv to an enterprise network with a username and a password?
    I need to use it over my university's wifi. theres no option to enter username and password. how to connect the apple tv to such enterprise network?

    Contact the University's IT dept, they may be able to set something up on the network to allow the ATV to connect without the need for a user name/password.

  • Does any body know how to connect the fingerprint scanner using jmf is it p

    Hai,
    I am not getting how to connect the fingerprint scanner how we can do it is it possible for device independent application
    If any body knows anything about this please mail me its very urgent for me
    hope u will be able to tell me something about this .
    Regards
    K Naveen Kumar

    Hi,
    Fingerprint scanners are not popular enough devices to be supported by Java yet. There's no general API or Java interface for it.
    Each manufacturer of a fingerprint device will probably just ship their own drivers or SDKs. More than likely DLL's, so you'd need to write some JNI to call them.
    If you want to allow your application to work with multiple devices, you will have to design it to do that. Ie. write a general "Fingerprint" interface, and write a class which implements that interface for each device you want to support.
    Eg.
    public interface FingerPrintAPI
         public void initialiseScanner ( )
                throws MyScannerException;
         public byte[] getFingerPrint ( )
                throws MyScannerException;
         public double getMatchProbability ( byte[] fingerprint1, byte[] fingerprint2 )
                throws MyScannerException;
         public void closeScanner ( )
                throws MyScannerException;
    }I haven't used a fingerprint device at all, but that's how I would approach it.
    regards,
    Owen

  • How do Connect the JAUD on a 915P Combo

    How do Connect the JAUD on a 915P Combo MB
    I have a case with a front panel. The wires are named:
    2 wires "SPK R" (2 connecters on the same wire) Red wire
    2 wires "SPK L" (2 connecters on the same wire) White wire
    1 wire "GND" (Grund) Black wire
    1 wire "M IN" (Microphone) Green wire
    1 wire "M Bias" (Microphone) Blue wire

    not sure ive looked at the main board manual  and my new blower case has the same front audio hook ups but i was not able to locate the connections  useing the mainboard manual that came with my main board im still wondering about how to connect the front audio  my self !  915p combo-fr

  • How to connect the iPad to a TV?

    I see that the Netflix app can now output from the iPad.
    We would like to show movies on our television. Is the "Apple iPad Dock Connector to VGA Adapter" the accessory to buy? Is there something else we'd need?
    We have older TV sets and use RCA component cables to input feeds. (You know, the old red-yellow-white cables.) (That's how our Tivo connects.)
    Currently, we connect our MacBook Pro to the TV using Apple's "DVI TO VIDEO ADAPTER KIT-GEN M9267G/A". You just plug a RCA cable into it and run that into the video input jack on the TV. You run another cable from the headphone jack on the MBP to the TV's audio. I realize that connector wouldn't work with an iPad, but what would?
    Our sets are standard definition (definitely not HD).

    The VGA adaptor delivers the best resolution of the 3 possible "video-out" solutions that Apple offers. Now that both Netflix and Air Video have reved their apps to do video out it seems like the next natural thing is to figure out how to convert the VGA out to an HDMI signal so we can send movies from our iPad to our TVs. There are meny VGA > HDMI converters and I have tried the Atlona VGA to HDMI Scaler/Converter (USB Powered). Model: AT-HDVieW as I saw it mentioned (http://bit.ly/c5U7nv) as a specific match to the iPad. It didn't work. There is no setting on the iPad to send video out rather than display it on its own screen. It switches automatically when it senses "something" attached to the VGA adaptor. This "sensing" works flawlessly when connected to a real VGA monitor but I'm guessing that the Atlona converter is not sending the needed signal back to the iPad to trigger it to dump the video. Will someone please pick up this ball so we can solve this? Other possibilities abound. Here's a few http://bit.ly/d4jgkD and http://bit.ly/asc4RJ THANKS!!

  • How to Connect the Apogee Duet with Digitech Vocalizer 3

    I have been trying to figure out how to interface my guitar and microphone with the Apogee Duet 2 using the Digitech Vocalizer 3 (voice correction). I would like someone from Apple to verify what I have found, but this is how I finally got it to work:
    1. Connect you microphone directly to the Vocalizer as shown in the instructions. If you are using a condenser mic, remember to activate the 48v power on the back of the Vocalizer.
    2. Set the Vocalizer output to mono (on back of device), and connect one cable from either output port of the Vocalizer to the Input 2 of the Apogee Duet.
    3. Use a 1/4" splitter (one mail 1/4" that splits into 2 female 1/4") to attach two standard 1/4" guitar amp cables to the output of your guitar. Connect one of these to the "Guitar In" port on the back panel of the Vocalizer.  Connect the other to Input 1 of the Apogee Duet.
    4.  Open the Apogee Maestro Software, and select "Input".  You should see both devices listed (1 and 2). The Apogee will not recognize the Vocalizer as a microphone, so set both of these devices to "Inst". 
    5.  Open Garage Band and add both instruments.
    6. When you add your guitar, remember to set your Input Source to "Mono 1" and turn the Monitor On so you can hear it through your hed phones. Also, make sure you have the headphone Icon selected on the Instrument panel.
    6.  When you add you Vocalizer (Instrument 2), select "Vocals" and "no effects". Remember to set your input source to "Mono 2" and turn your Monitor On so you can hear it through your hed phones. Also, make sure you have the headphone Icon selected on the Instrument panel.
    7. If you want to hear and record both instrumental tracks, go the "Track" menu and select "Enable Multi-Track Recordning."
    In summary, the Apogee Duet does not appear to recognize the Vocalizer as a microphone, so you have to set up the connection from the Vocalizer to the Duet as another instrument.

    #3 Can't you just plug your guitar into the Vocalizer's guitar in jack and then use the guitar thru jack to the apogee?

  • How to connect the Satellite Pro P100 to Hifi

    I've got Satellite Pro P100. How to connect this notebook to HiFI
    This is probably easy, but what can i say... just call me stupid.
    I've got the lead that goes out of the headphone jack, it links up to my hifi nice.
    Trouble being, there's a nasty hiss in the background. Tried plugging my boys mp3 player into the lead, and that works fine.
    Any chance of some help... thanks

    Hi
    In my knowledge you can connect the Sat Pro P100 to HiFi only via a 2-RCA Audio Y cable adapter. In my knowledge the notebook does not support the S/PDIF audio out so you will be able only to use an analog sound port.
    You could also buy a stereo adapter with 2x cinch jacks to connect the notebook to the Hifi. Such adapter can be plugged into the headphone jack
    Check this:
    stereo adapter
    I think you should visit the nearest notebook dealer. He can show you the right and supported cables and adapters.

  • How to use an external start button for 6024E w/ sc-2345, I would like it to function like a start button in LabView but I don't know how to connect the external button to the sc-2345's connector block

    I am confused as to how to connect my external start botton. I would like it to function like a start button on a front panel of a VI. I would like to use the +5V on pin 14 but I really don't know where to go from here. Any guidence for a novice would be most appreciated.

    phod,
    This is the LabVIEW Real-Time forum, so I suggest that in the future that you post this type of question to the Multifunction DAQ forum.
    For the simplest solution you will have to connect your button to a digital line of your board, consult the sc-2345 user manual for a diagram of where these lines are exposed. You will have to connect your start button in series with a line that is high, such as your 5V pin or another digital line. Then connect this to a digital line that will be your start trigger.
    Your program can poll the digital line that is connected to your button in a while loop and when it goes high, it lets the rest of the program execute. For the programming, I suggest you take a look at the shipping examples that come with LabVIEW. If yo
    u have LabVIEW 7.0 go to Help>>Find Examples. Open Hardware Input Output>>Traditional DAQ>>Digital Input and Output>>E Series for some examples of digital I/O programming with E-series boards.
    Hope that gets you started.
    Gerardo

  • How to connect the I-Trigue 5600 to a DVD player???

    I got a set of I-Trigue 5600 and thinking of connecting all 5 speakers and woofer to the back of DVD player to get the surround effect when watching DVD. The problem is I can just plug all 5 speakers to the back of the DVD player but how can I connect the sub-woofer to the DVD player as there is no cable to connect them together? Is there some sort of cable or adapter I can buy to connect them together? Thx in advance for any help!!!

    have you tried that setup already?
    my guess is that the subfrequencies are still combined with the front channels, and if I correct, your speakersystem will redirect them to the sub. just give it a try.
    regards

  • How to connect the two field which have a diffrent length

    Hi,
           i have two table one is VBRP-VGBEL CHAR 10
           second is                    MKPF-XBLNR CHAR 16
    both are same data means vgbel eq xblnr.
    how to connect these table because when i connect these table it gives me error
    have a same type and length.
    please give me reply soon . Thanks.
    dinesh

    HI
    I GOT THE SAME PROBLEM AT THAT TIME I DONE LIKE THIS
    I THINK IT MAY HELPFULL FOR YOU
    OBJID = 6 CHAR
    SOBID =  40 CHAR
    I GOT THE SAME ERROR WHAT YOU GET
    I NEED ONLY 6 CHAT SO THAT WHY I HAD WROTE THIS LOGIC
    1ST I HAD DECLARED THE SAME STRUCTURE TWICE
    IN FIRST ONE IT IS NORMAL DECLARATION
    IN SECOND ONE I HAD DECLARED THAT 2 FIELDS AS THE SAME LENGTH
    I HAD PUT THAT IN THA BOLD LETTERS
    AND AFTER THAT I HAD LOOPES THAT WORK AREA AND CONVERTED THAT SZE
    REWARD IF USEFULL
    TYPES : BEGIN OF ST_HRP1001,
             OTYPE TYPE HRP1001-OTYPE,
             <b>OBJID TYPE HRP1001-OBJID</b>,
             RELAT type hrp1001-RELAT,
             BEGDA TYPE HRP1001-BEGDA,
             ENDDA TYPE HRP1001-ENDDA,
             SCLAS TYPE HRP1001-SCLAS,
             <b>SOBID TYPE HRP1001-SOBID,</b>
            END OF ST_HRP1001.
    TYPES : BEGIN OF ST_SOBID,
             OTYPE TYPE HRP1001-OTYPE,
             <b>OBJID TYPE HRP1001-OBJID,</b>
             RELAT type hrp1001-OBJID,
             BEGDA TYPE HRP1001-BEGDA,
             ENDDA TYPE HRP1001-ENDDA,
             SCLAS TYPE HRP1001-SCLAS,
             <b>SOBID TYPE HRP1001-OBJID,</b>   
        END OF ST_SOBID.
    SELECT OTYPE
             OBJID
             RELAT
             BEGDA
             ENDDA
             SCLAS
             SOBID FROM HRP1001 INTO TABLE IT_HRP1001
                        WHERE OTYPE = 'D'
                            AND OBJID IN S_OBJID
                            AND BEGDA GE DATE-LOW
                            AND ENDDA LE DATE-HIGH
                            AND ( SCLAS = 'E' OR SCLAS = 'ET' ).
      IF SY-SUBRC NE 0.
        MESSAGE 'NO RECORD FOUND FOR THE GIVEN SELECTION CRITERIA ' TYPE 'E'.
      ENDIF.
    LOOPING TO CONVERT THAT FIELD LENGHT
    <b> LOOP AT IT_HRP1001 INTO WA_HRP1001.
        WA_SOBID-OTYPE = WA_HRP1001-OTYPE.
        WA_SOBID-OBJID = WA_HRP1001-OBJID.
        WA_SOBID-RELAT = WA_HRP1001-RELAT.
        WA_SOBID-BEGDA = WA_HRP1001-BEGDA.
        WA_SOBID-ENDDA = WA_HRP1001-ENDDA.
        WA_SOBID-SCLAS = WA_HRP1001-SCLAS.
        WA_SOBID-SOBID = WA_HRP1001-SOBID.
        APPEND WA_SOBID TO IT_SOBID.
      ENDLOOP.</b>
      SELECT OTYPE
             OBJID
             AEDTM
             UNAME
             DELET
             CANCR
            NCONT
              FROM HRP1026
              INTO TABLE IT_HRP1026
              FOR ALL ENTRIES IN IT_SOBID
                 WHERE OBJID = IT_SOBID-SOBID
                 AND ( OTYPE = 'E' OR OTYPE = 'ET' )
                     AND DELET = 'X' AND
                     BEGDA GE DATE-LOW  AND
                     ENDDA LE DATE-HIGH.

  • HT4145 how to connect the i pod to airport extreme

    I am trying to figure out how to connect to my airport extreme from my ipod- anyone who can give me a stepby step answer?
    I am not sure which operating system it is...
    Thanks!

    If the AirPort Extreme is allowing other devices to connect, it is not the issue.
    Follow the iOS Troubleshooting Guide for Wi-Fi Networks and Connections
    http://support.apple.com/kb/TS1398
    You will be better served to post in the iPod support area for questions about the iPod.  Post here:
    iPod

  • How to connect the Liquid Mix?

    Hi, I'm thinking about adding a Liquid Mix to my rig, but I only have 1 FW 400 port, used by the Duet. The HD goes in the FW 800. How can I connect the Liquid Mix to my Powerbook? Can I use a PC Card? Which one? Will this bring me latency problems in Logic 8? Thanks!

    firewire pc-card, that way it gets it's own firewire bus which it pretty much needs. Just using an audio interface for stereo playback on the same bus I had to set the thing to 24 channels instead of 32 to get rid of bandwidth problems.

  • How to connect the speackers for the CT4830

    Hello. I can't find how to plug the subwoofer to the card.

    Typical 2. (and 5.) speakers are connected using a single cable from the sound card to the sub, with the fronts/satelites connecting to the sub. Very few if any 2. sets have a front and sub connection.
    o_coqui wrote:
    or to divide the front or rear out to plug the center and subwoofer speackers.
    From the sounds of it you want to connect 5. speakers to the card, isn't going to happen. You want to use 5. speakers either get a sound card that supports 5., or use onboard if it supports 5..
    As for the digital, not going to work with analogue speakers. You plug in speakerrs that don't have a digital connection on them and you will get nothing out of it.

  • How to connect the two virtual machine .

    I installed VM workstation and created two virtual machine .Please suggest me how to connect them internally each other though vm network editor.I want create RAC Setup for practice.

    NAT is the default adapter type in VirtualBox, which will work in almost any configuration and networking environment. Using the NAT adapter, the host system will establish connections on behalf of the guest OS. NAT requires that the corresponding VM guest adapter uses DHCP and cannot be used to provide any services unless you configure port forwarding (>1024) at the VirtualBox VM NAT adapter.
    Bridged networking is the most transparent adapter type, but requires a physical network adapter on the host OS, which is limited depending on the host system and hardware, e.g. wireless. It also requires that the user understands network and routing restrictions of the host system in case of using the interface to communicate between the host and VM. A combination of host-only and NAT may sometimes be necessary to allow the VM to connect to the internet and allow the host to communicate with the VM guest OS.
    Btw, the host-only adapter IP actually works on behalf of the host OS and can be used to allow the VM to access the host system. So if Internet is not required, the NAT or bridged adapter are not required. I'm not sure if many people realize that, since it's not really mentioned in the documentation. So if you use the host-only adapter, simply use the host-only IP instead of the host system real IP to connect the VM to the host OS.
    I also switched to VirtualBox a couple of years ago, mainly because it provides more VM hardware options, is free and because of the ability to manage multiple virtual machines and group them together. I have about 70 virtual machines for testing and evaluating configured on my home computer. I also like the option in VirtualBox to clone a VM based on a Snapshot.
    VMware provides a Virtual Network Editor in VMware Workstation (KB 1018697), which allows to customize any of the existing virtual network adapter or add new ones. The available technologies under any Type 2 hypervisor are very similar between different products:
    http://www.vmware.com/support/ws45/doc/network_configure_ws.html

Maybe you are looking for