How to connect to my router through airport

I can connect to my router configuration page when i use a direct ethernet connection, and use 192.168.1.1 in Safari.
However, does any one know how i access this page when the router is plugged into my airport base station, and i am wirelessly connected to the Airport network.
Thanks.

Yes I know the IP address when connected directly with an ethernet cable- 192.168.1.1
This works fine with ethernet, but I wanted to see if there was a way to connect when the router is connected into my airport, and I am connected to the airport network. The Airport is distributing the IP addresses, and the router is in bridge mode, simply supplying the internet signal on to the airport base station. The base station is controlling my PPPoE.
My router has a configuration page with my web info, such as speed, and other statistics. It is useful to refer to to see if I am getting a good speed.
If it can't be done, then so be it. But just thought there would be a way to connect through the airport and on to the router.
Thanks for you advice.

Similar Messages

How to connect a ADSL router to AirPort Extreme?

Hallo,
my local internet service provider forces all costumers to use their modem/router to connect to the Internet using a DSL connection.
I have one external public IP (v4) and the router has an editable IP for the LAN set to 192.168.1.1 .
The ISP router can act as DHCP server and NAT; I can disable the DHCP.
What I would like to do is connect it to the Airport Extreme WAN port and give all the control to the Airport extreme: I want to use his DHCP server, NAT, port forwarding etc.
My problem is that I am able to have Internet connection only if the ISP router has DHCP control and Airport Extreme is set to Bridge mode.
In this configuration, in the Airport Internet configuration panel, the connection is set to Ethernet, IPv4 is using DHCP, Airport IP is 192.168.1.133 and the ISP router has 192.168.1.1 . I also have the DNS IPs set to the ones suggested by the ISP and Bridge mode.
In this way it works: all computers can share Internet connection.
What I am trying to do is:
- disable DHCP in the ISP router;
- in the Airport extreme Internet panel I choose to manually setup IPv4 and I type the same vales it is getting when set to DHCP mode: 192.168.1.133 for the Base and 192.168.1.1 for the router using the ISP dns and I select Share pubblic IP. In the DHCP panel I choose 10.0.1 class.
I save changes and... I got that Internet is no working anymore and I cannot access the ISP router control panel.
Does anybody have suggestion about things to try to not use ISP router DHCP or configuration changes I could try?
Thanks in advance for any help about it!

Thanks for the reply,
at the end it seems that my airport extreme works too BUT with an error message saying "double NAT" and the front led turned to yellow. I have ignored such error because things seems to work and so the led color goes to green.
What I had to do here is:
- set previous router to IP 192.168.1.1
- turn off DHCP on my previous router;
- leave on the NAPT (NAT) service on previous router and set it with start and stop address to the same IP I am using for the Airport Extreme (192.168.1.100);
- open all ports and services on previous router by faking the mac address of the Computer's NIC I was using to configure router. I say faking because previous router wants to know for which computer the ports have to be open, so I had to use the same mac address of the Airport extreme. I cannot type it, previous router will get it automatically when configuring it.
- on the Airport Extreme, Internet side, I had to manually configure Internet options using Ethernet mode: I set the IP 192.168.1.100 for the Airport base. Then I have enabled DHCP on class 10.0.1.x .
Airport extreme seems to work with all features now, I hope that "double NAT" warning will not create any trouble. Anybody knows about that?

How to connect a hard drive on Airport Extreme (second edition)

how to connect a hard drive on Airport Extreme (second edition)? Does it need a special format? It is now fromat on FAT32, but i don't see it ??

The USB port your Mac is high powered. The port on the AirPort Extreme is not.
So, it tends to be borderline as far as its ability to supply sufficient power to a hard drive...even if the hard drive has its own power supply.
Often, users...including me....need to use a powered USB hub when they attach any drive to the USB port on the AirPort Extreme.
You might want to give that a try. Double check to make sure that the drive is formatted in FAT32 as well, since Windows NTFS or exFAT will not work with the AirPort Extreme.
Powering down and restarting the entire network.....modem first, then router, etc.....is something that you would always want to do after any change or addition to a network.

Trying to connect Verizon wireless router to Airport Extreme but error says Ethernet unplugged.

Trying to connect Verizon wireless router to Airport Extreme and error says Ethernet Unplugged.

So, AirPort Utility running on the Windows Vista desktop can "see" the AirPort Extreme and displays its icon, but gives that error message at some point in the setup process? How far does it get?
Other questions that may help me (or somebody else) understand your problem better:
Which of the pieces were verified as working before the introduction of the AirPort Extreme?
Did you have the desktop computer attached to the Verizon GT704WGB with one of the Ethernet cables you are now trying to use? Which one? Have you tried the other one to be sure it also works?
Are you using the same port on the GT704WGB? Have you tried another one?
If the desktop has multiple ethernet ports, are you using the same one?
Had you done any special configuration of the ethernet port on the Verizon GT704WGB to get it to work with your desktop?
What category ethernet cable are you using? 3? 5? 5e? 6?

How to connect PC to data through iPhone (unlimited metropcs)

How to connect PC to data through iPhone (unlimited metropcs). Now I tried PC write: limited connect

The following gives details about how to set up personal hotspot so your computer can share your phone's data connection. Note that in order for this to work you must have a cellular data plan that supports this feature. You may need to contact your cellular provider. http://support.apple.com/kb/HT4517

Where did button go for new itunes to connect speakers/ dvd player through airport?

where did button go for new itunes to connect speakers/ dvd player through airport?

I realize this question is ubiquitous in this forum....I guess I'm specifically interested in knowing WHY won't the Extreme software recognize the Express unit?

How to setup ADSL moden router and Airport Express 802.11n (1st Generation) to provide internet and airplay connections to multiple devices?

I have a Netgear wireless ADSL modem router (wireless + four ethernet out ports) that i'd like to connect to a 1st gen Airport Express to create a small home network to provide internet access for a MacBook, iPhone and Apple TV, and to provide Airplay connection to the Apple TV and Airport Express audio output jack.
I'd like to turn off the wireless function of the ADSL modem router, and to have from one of its ethernet out ports an ethernet cable providing internet directly connected to my MacBooks ethernet port.
Then from one of the other ethernet outs on the ADSL modem router an ethernet cable connected to the Airport Express's ethernet port. This would be to provide wireless internet connection for the Apple TV and iPhone via WiFi from the AE.
At the same time as the MacBook is receviing internet soley via the ethernet in port, i'd like it to have WiFi connection to the AE to provide Airplay connection to the Apple TV and the AE's audio out jack.
Is this all possible? How should I go about to configure this? How should the AE's ethernet port be configured?
Any special modes the ADSL modem router or Airport Express should be in? ie bridge or client?
Thanks

On the ADSL modem router web-based interface, should I set any security setting? I think not as there'll be no wireless signal coming from it, only wired ethernet connections to both MacBook and AE. Security should only be set on the AE to prevent someone from accessing its WiFi signal. Is this assumption correct?
These are all correct!
How should I go about setting up security for this network?
First I would recommend that you configure the AirPort Express for WPA2 Personal. This will provide you with the greastest level of security while still providing excellent bandwidth performance.
You would configure wireless security for the Express by using the AirPort Utility on a Mac, PC, or iOS device. Using your MacBook Pro as an example, you would do so as follows:
Run the AirPort Utility.
Select the Express, and then, click on Edit.
Select the Wireless tab to enable it.
Set the Wireless Security option to: WPA2 Personal
Enter the desired password in both the Wireless Password & Verify Password fields. Note: Use of a "strong" password is encourage here. By strong, I mean use a mix of upper/lowercase letters, numbers, & punctuation marks. Try not to use common dictionary words. If you operate your wireless in an area where security is of an utmost concern, I would further suggest that you change the wireless security password every 60-90 days. Also don't forget to change the default AirPort Base Station Administrator password as well.
Click on Update and allow the Express to restart.

How to connect my macbook to the Airport with the same IP?

Hi to everybody!Most of the times I want to use amule it is firewalled because the IP changes everytime I connect my macboook to the Airport express: 10.0.1.2 or 10.0.1.3 and so on. Is there a way to say that I want my macbook to be always connected with the same IP? Since I couldn't do this I started to map the amule ports (TCP and UDP) for each IP, but I realised that I can't use the same ports (let's say TCP 4662 and UDP 4672) for different IPs. Why is that?
Thanks in advance!

lellolelotti wrote:
Most of the times I want to use amule it is firewalled because the IP changes everytime I connect my macboook to the Airport express: 10.0.1.2 or 10.0.1.3 and so on. Is there a way to say that I want my macbook to be always connected with the same IP?
I believe that an AirPort Express can be configured to do that. Launch AirPort Utility, enter "manual setup" mode, select the Internet panel, then the DHCP tab. There should be a section of the screen at the bottom labeled "DHCP Reservations". Click in the "plus" sign at the bottom of that section and fill in the details that you want.
I can't use the same ports (let's say TCP 4662 and UDP 4672) for different IPs. Why is that?
You have to tell the router to send messages addressed to a certain port to a specific IP address, otherwise it wouldn't know how to route the messages. It would be like trying to assign a phone number to two different phone line circuits.

How to connect a Philips fidelio to airport extreme?

I just purchased an Airport Extreme Time capsule. I cannot connect my Philips fidelio AD7000W to the network. There are no WPS button on the Airport Extreme. There is a WPS printer connection option in the Aiport app menu option but nothing for sound system. Anyone knows how to make the connection ?

Instructions on how to connect the Fidelio to a non-WPS supported router is covered in the User Guide starting on page 13. On step 4 you would enter the specifics for your wireless network. That would be the network name, the wireless security type & wireless password. You will also want to choose the DHCP mode as enabled for these speakers.

Can't connect imac to internet through Airport Express

Hello
I am trying to connect my new imac (2.4Ghz,OS X 10.5) to the internet through my Airport Express (v6.3) but have encountered some problems.
The set up goes like this:
Cable Internet <wired> TP-LINK Router <wired> AE <wireless> imac
The internet is coming from my landlord on the bottom floor of my apartment so I can't change the router.
The router is assigning a static IP to my AE (192.168.5.101).
I am using WEP 128 bit security.
I have set the AE through Airport Utility to act as a Bridge.
On the imac I set the Network preferences to manually select an IP address (192.168.5.110) which is out of the range of the Router (192.168.5.101-108).
The AE connects and lights up green and the imac recognises the AE but I still cannot access the internet...
I have also tried to wirelessly connect my PC laptop to the AE using other static addresses but I still can't connect to the internet.
Can anyone please help??
Regards
Starwolfgang

Hello Starwolfgang. Welcome to the Apple Discussions!
The router is assigning a static IP to my AE (192.168.5.101).
Are you sure that this provided IP address is static? If so, you also need to note the provided DNS server(s) IPs as well.
On the imac I set the Network preferences to manually select an IP address (192.168.5.110) which is out of the range of the Router (192.168.5.101-108).
Since you configured your AX in bridge mode, your computer will be dependent on the NAT (& possibly DHCP) services provided by your apartment's router. Assuming that your landlord doesn't filter out any IP addresses and that the IP address you set is valid, you need to compare your iMac AirPort's DNS server address settings with that provided by your apartment's router to be sure they match.
Finally, assuming that your apartment provides you with an Ethernet jack, if you connect your iMac directly (via Ethernet) can it access the Internet?

How to connect printer epson l210 to airport express

How to connect and setup printer epson l210 to airport express

Hey Love iapd,
Thanks for the question, and welcome to Apple Support Communities.
The following article will outline how to set up a printer that may be connected to an AirPort Express.
OS X Mountain Lion: Set up a printer connected to a Time Capsule or AirPort base station
http://support.apple.com/kb/PH10875
Additional information:
USB printer troubleshooting for AirPort Express, AirPort Extreme, and AirPort Time Capsule
http://support.apple.com/kb/TS1253
Thanks,
Matt M.

How to connect Iphone4s and Ipad2 through bluetooth

How to connect Iphone 4s and Ipad2 through bluetooth normally as we do for some general phone

you can only connect your iPhone 4S and iPad2 for the purpose of tethering your iPhone's internet connection to the iPad. Any other connection is not supported.

HT4145 how to connect the i pod to airport extreme

I am trying to figure out how to connect to my airport extreme from my ipod- anyone who can give me a stepby step answer?
I am not sure which operating system it is...
Thanks!

If the AirPort Extreme is allowing other devices to connect, it is not the issue.
Follow the iOS Troubleshooting Guide for Wi-Fi Networks and Connections
http://support.apple.com/kb/TS1398
You will be better served to post in the iPod support area for questions about the iPod. Post here:
iPod

How to connect laptop to router by using udp receiver

I try to communicate between computer and laptop via router. Computer connect to router by wire. laptop have Wireless Mini Card. I open udp receiver to connect to router. How to connect to router ? what is net address number ? and what is port number ? how to find them ?

You can only connect to a router port if the router is running a service that
Allows you to do so. What kind of connections are you trying to do?
The net address is the ip address in u32.
The port is determined by the service you want to access.
What do you actually want to do with all this?
We need much more info. Router model?
LabVIEW Champion . Do more with less code and in less time .

How to connect Macbook to TV through Dvi to VGA adapter.

I recently got s Macbook and was wondering how to connect it to my 32 inch sony tv. I have the dvi to vga adapter and recently bought an adapter that converts the VGA into RGA adapters + S video (all of which my tv has) When I connect the TV with these components nothing happens. I am curious to know what the next steps are to getting the Macbook to recognize the tv and how to produce an image on my TV. Any input would be helpful

what plugs do you really have.. that was confusing? This is a Macbook (not pro)?
First, it could be as simple as going to System Preferences|Displays| and choose to "Detect Display". It may not be recognizing you plugged something in.
If you want to connect you should probably get the proper Apple mini-dvi adapters to match exactly what your TV has. I use the adapter from mini-DVI-to-DVI with my DVI-ready TV and it works great. They have one adapter for mini-DVI-to-VGA, and one from mini-DVI-to-Svideo. Note that multiple adapters assume you have 100% compatible input when often adapters "cheat" on the actual output side... data and signals are probably not getting thru... your Mac can't recognize the TV as connected.
If you want to live dangerously, you might try using the mini-to-DVI adapter with a DVI-HDMI cable (single cable, no adapter) and see if that works (HDMI is a legit DVI spec so it should work, it works in reverse for my DVD player to TV connection)

How to connect to my router through airport

Similar Messages

Maybe you are looking for