How to connect UMI 7764 with servo driver
I'm using PCI-7344 & UMI 7764 to control ac motor on servo motor (Panasonic MUDS5A5A1A),
but i have a question, the voltage of UMI 7764 is 5V while voltage of driver is from 12 to 24V. What should I do?In addition, I don't know how to connect UMI7764 with the driver . The attachment is the connection drawing.
Thanks!
Attachments:
2.JPG 76 KB
Check out this link where I have given the solution for your problem.
http://forums.ni.com/ni/board/message?board.id=240&message.id=2916
Regards,
Giridhar Rajan
Automation Engineer, Design
Cruiser Controls
Mumbai, India
Similar Messages
-
Problem with Flexmotion 7344, UMI 7764 and servo driver parts
Hi to all of you, I've a great problem with my motion system.
This is formed by:
1.Flexmotion 7344, cable and UMI 7764 (NI-kit)
2. 2 servomotor and 2 incremental encoder
3. 2 Motor drivers
The problem is that the motor drivers (AXOR MICROSPEED) can' t work with the NI-kit, sometimes the motor go and sometimes not, so the repeatabitlity is very very low.
I work a lot trying to solve this but i suppose that the PID of the driver runs counter to the PID of the Flexmotion.
This thing was confirmed by the NI Italy staff. They tested the system and comfirmed my sensations but i had not any feedback about the type of drivers that i' ve to buy to work with my system.
I try to attach the datasheet of the motors and the encoders at the post.
If any one can help me in some ways i thank a lot. If necessary is possible to contact me by mail at [email protected]
Motor type: 17PL085
Encoder type: EH17 M500 Z 5 P 6 X 3 P R 7 8
The last important thing is that the system with this configuration of motors, encoders and drivers worked in the past with the old NI flexmotion 6C.
What we would do is to mantain this configuration of motors, encoders and drivers but substitute the old flexmotion with the new.
Thanks to all.
Andrea
Attachments:
SERVOMOTORI SIBONI.pdf 833 KB
AXOR.pdf 238 KB
encoder ELTRA.pdf 119 KBAndrea-
Yes. According to the datasheet, that drive can be ordered in different versions. There are different options like control mode and feedback type. Please give us your part number. Typically, position controllers expect the drive to accept a torque reference(+/10V). It is possible to use it in velocity mode, but you need the differential option. If that is the case, then you have 2 PID loops to worry about and tune. One in the drive, and one in the controller.
Brian -
UMI 7764 with servo AND stepper
Dear Forum,
I'm working on a UMi 7764 board with a 7340 motion controller.
I want to interface 3 motors:
-axis1&axis 2 are servo drive (AKD driver & Kollmorgen motors).
-axis3 is a stepper interfaced with a SMD7610 driver.
I'have a problem with the inhibit input (S2) switch of the 7764:
for the AKD drive it should be set to Active high but for the stepper driver SMD7610 it should be Active low!
How can I find a workaround?
best regards PFCheck out this link where I have given the solution for your problem.
http://forums.ni.com/ni/board/message?board.id=240&message.id=2916
Regards,
Giridhar Rajan
Automation Engineer, Design
Cruiser Controls
Mumbai, India -
i am a OS10.7.4 user. yesterday i bought a Lacie external hard disk but error message appear said " You cant open the applicant LaCie setup assistant because PowerPC applicants are no longer support". please help me how to connect my mac with Lacie??
You do not need the Setup Assistant; in fact, you do not need any software on an external hard drive. I have two LaCie's; I erased the drive as soon as I plugged it in. You will need to format it anyway because most hard drives come Windows formatted. So, if you only want to use it with the Mac, highlight it in Disk Utility and choose Mac OS Extended (Journaled) as the format and the GUID Partition scheme under Options. While doing that, it will erase the drive (and get rid of the LaCie software) - once finished, your drive is ready to use for Time Machine or any other backup plans you have for it.
-
How to connect my ipad with mac using bluetooth?
how to connect my ipad with mac using bluetooth?
You can't so quit trying. Take a look at this to see what is supported with regard to Bluetooth connections in iOS.
iOS: Supported Bluetooth profiles -
Dear fellows, I am having a trouble in how to connect my mac with an iPad mini in order to have an access to the internet.
If you are attempting to share your iPad mini's cellular data connection with the MacBook, please check out the following Apple Support article for additional details on how to do so.
-
HT1695 How to connect my iPhone with the printers at school? Many thanks
How to connect my iPhone with the printers at school? Many thanks
They must be Airprint capable printers... if they are not, then there is no supported way of connecting to them.
Airprint 101 -
How to connect Apple TV with an iPad ?
How to connect Apple TV with iPad ?
Welcome to the Apple Community.
Assuming both devices are on the same network and that AirPlay is not turned off on the Apple TV, then simply tap on the screen when you are watching content you wish to stream to your Apple TV, then tap the airplay icon that appears in the control bar, choose the Apple TV from the menu that appears.
When displaying the content you wish to mirror on the iPad 2 (or better), iPad Mini, iPhone 4S (or better), double tap the home button (quickly) and swipe the bottom row of apps to the right to reveal the playback controls, tap the AirPlay icon and select your Apple TV from the list of available devices. -
I used the article "How to connect Sony Tablet with adb protocol through USB?" Article ID:474705.
Everytime I restart the computer now I get a open with window.
When I select Notepad and open it I get
0x54c Noswal\.android\adb_usb.******
How do i undo that.
If it helps the Article ID:474705 this says at one point
3. Open a shell prompt and enter the following command: echo "0x54c" >> $HOME/.android/adb_usb.******.
I gues that's what's creating the problem.
Please help.Hi elishacuthbert.
Try disabling the start-up items in your computer to troubleshoot the issue. Follow the steps mentioned below:
Right click on the Taskbar > Task Manager > Start-up > Select the applications > Disable.
Note: If my post answers your question, please mark it as an "Accepted Solution." -
How to connect excelsius dashboard with webservice
Hello Experts,
how to connect excelsius dashboard with webservice for query. Can any one tell me step by step?
Thanksplease check this
unable to use web services
good luck -
How to connect Toshiba TL838 with facebook profile?
How to connect Toshiba TL838 with facebook profile?
When i try to connect toshiba generate email with info and links to connect accounts facebook with toshiba places but when i click links i see only errors.
_*EDIT*_
*Ok i flashed QR code with my phone and is connecter now :)*
Moderators please close thead
Message was edited by: junioreks>Ok i flashed QR code with my phone and is connecter now :)
Thanks for sharing! -
How to connect oracle database with JAVA
how to connect oracle database with JAVA....
using j2sdk and Jcreator . which connector to use .. what are the code for that ..PLEASE .... Ask in an Oracle Java forum.
And read the documentaiton. There is a whole document devoted to doing that. http://download.oracle.com/docs/cd/B19306_01/java.102/b14355/toc.htm has examples.
PLEASE ... do not ask product questions in a forum which clearly has a title saying it is devoted to assisting with download problems. -
How to connect mySQL database with jdbc
Who can tell me how to connect mySQL database with jdbc? Thanks
http://onesearch.sun.com/search/developers/index.jsp?and=connect+mysql&nh=10&phr=&qt=¬=&field=title&since=&col=devforums&rf=0&Search.x=24&Search.y=16
-
How to connect MySql database with JSP
Dear everyone,
how to connect MySql database with JSP......It's too bad that nobody has ever asked this question before...
-
How to connect Developer 6i with third party Databases
How to connect Developer 6i with third party Databases
Hi,
Oracle Forms 6i comes with a Oracle Client Adaptor, OCA, that allows you to connect to 3rd party databases. Starting Forms 9i you use gateways.
Frank
Maybe you are looking for
-
Why can I drag and drop from Photos to Pages, but not to Microsoft Word 2011
I'm unable, under OS X 10.10.3, to drag and drop pictures from Photo into Word for Mac 2011. I can paste from Photos into Pages. How can I add Word to the list of programs that can take pasted photos pasted from Photos
-
Why am I getting an error when trying to install?
Hi, I tried to download the OS X Mavericks update for my mid-2012 model of the Macbook Pro - 15 inch, but it would not install. For whatever reason it keeps saying: Unknown Error. Please try again later (04). I don't know why this is happening. My fr
-
ESB Calling a REST web service
Has anyone use the ESB to call a RESTful web service? Is there a REST service adapter for JDeveloper ESB designer? -Thanks.
-
QFS Meta data resource on sun cluster failed
Hi, I'm trying to configure QFS on cluster environment, to configure metadata resource faced error. i tried with different type of qfs none of them worked. [root @ n1u331] ~ # scrgadm -a -j mds -g qfs-mds-rg -t SUNW.qfs:5 -x QFSFileSystem=/sharedqfs
-
How Oracle Service Bus integrate Microsoft CRM
Hello, I want to use the OSB like an "client" accessing MS CRM. I want to expose "CRM services" on the bus OSB. What is the best practice to integrate MS CRM ? For Oracle SOA, it is available the application's adapters (Microsoft CRM). Thank you !