How to Copy USB Recovery Drive back to accidentally deleted Recovery Partition Windows 8

I was Creating USB Recovery Drive for my Windows 8.1 and Then I accidentally got my Recovery Partition deleted.. Now I want to restore RecoveryPartition back on my Hard drive. Provided I have the Recovery Data on USB Recovery Drive.. Now what should I do? Please help.

If you've made a Dell Backup and Recovery USB you can restore all the factory partitions:
http://dellwindowsreinstallationguide.com/dell-backup-and-recovery-1-8-1-71/

Similar Messages

How to erase USB flash drives?? Thanks, Michael

How to erase USB flash drives on my MacBookAir ?? Thanks, Michael

Welcome to Apple Support Communities
To erase them, you can use Disk Utility, in /Applications/Utilities > http://pondini.org/OSX/DU1.html
When you open Disk Utility, choose the external disk in the sidebar, go to Erase tab and erase the disk

How to access a USB disk drive connected to Airport Extreme from a Windows 7 PC?

How can I access a USB disk drive connected to Airport Extreme from a Windows 7 PC?

...Called it a roaming network. Wireless mode is create a wireless network. I have checked allow this network to be extended. Probably need to uncheck that?
Yes, that option should be deselected as it only pertains to when both routers are interconnected by wireless. Since you have a roaming network, they of course, would be interconnected by Ethernet.
The other important settings for a roaming network are:
Each router must have a unique station name. For the AirPort, this would be called its Base Station Name. I believe the default station name for Linksys routers is: linksys
Each router must broadcast a wireless network with an identical Network Name. For the Linksys, Network Name is the same as its SSID.
Each router wireless network must use the same Wireless Security type and password. The Linksys WRT-54G is capable of up to WPA2 Personal. If you have it set to this level of security, the AirPort should be at the same setting.
Make sure that each router is not on the same Radio Channel for the 2.4 GHz radio. In the US, there are basically only three non-overlapping channels: 1, 6, or 11. Set each so that they don't use the same channel but use of those three choices.

How do i recover data from an external hard drive that was accidentally deleted? After I verified the drive, a message appeared that said my drive needed to be repaired. When I tried to access the drive again, the 700 Gigs of music is gone!

How do i recover data from an external hard drive that was accidentally deleted? After I verified the drive, a message appeared that said my drive needed to be repaired. When I tried to access the drive again, the 700 Gigs of music is gone!

Stop using the drive immediately, un plug it.
Buy a copy of ProSoft DataRescue 4 and use it to search for deleted files.

How to recover the recovery partition after delete all hard disk partitions

hallo
how to recover the recovery partition after delete all hard disk partitions in toshiba satellite pro c850-1fn ?
note that : I did not work recovery disc or usb to my laptop.
I have need of your help.

Satellite Pro C850-1FN (PSCBXE-01700EEN)
Restore the hard disk to its original out-of-the-box contents using Toshiba recovery media. All of the original partitions will be restored, including the recovery partition.
If no recovery discs were created, you can obtain them from Toshiba.
Toshiba Europe Backup Media Online Shop
For instructions, see the section Restoring the pre-installed software from your created Recovery Media on p. 4-18 of the User's Manual (attached).
-Jerry

How to install a recovery partition

After installing 10.10.1 - 14B25 I no longer have a recovery partition. The OS X 10.10.1 works fine but I am lost on how to add a recovery partition. Some help on how to after the fact create an OS X 10.10 .1 recovery partition will be appreciated. I failed to save the 10.10 installer

BINGO.... I downloaded the full installer 5 GB and ran it over my 10.10.1 Macintosh HD with no Recover Partition. Bingo, I now have my primary HD back with an updated 10.10.1 Recover Partition
Kappy,
I though your assessment was correct; however, it worked for me and I did NOT have to erase my Macintosh HD
All is well again and it was a time consuming learning experience and I now have a 10.10.1 Recovery Partition

How come my messages keep coming back after I delete them???

How come my messages keep coming back after I delete them???

Apple's Mail application can use either IMAP or POP. In fact Gmail can be set either way.

How can I get my pics back that were deleted from icloud?

How can I get my pics back that were deleted from icloud?

Read this:
http://support.apple.com/kb/HT1414

How can i restore my safari history, i accidentally deleted all of it on my macbook pro?..

how can i restore my safari history, i accidentally deleted all of it on my macbook pro?..

Triple-click the line below on this page to select it, then copy it to the Clipboard (command-C):
~/Library/Safari
Quit Safari.
Select
Go ▹ Go to Folder
from the Finder menu bar. Paste into the text box that opens (command-V), then press return.
A folder window should open. Restore the file named "History.plist" in that folder from a backup that predates the unwanted changes.

How do I find folder contents which were accidentally deleted?

How do I find folder contents which were accidentally deleted?

They would be in your Trash. Unless you have emptied your trash since then, in which case you'd need to use a file recovery tool such as Data Rescue.
Of course, if you use Time Machine for backups, you can easily retrieve the file from TM.
Matt

How do I download MUSE again after having accidentally deleted it

Hello!
I am in a dilemma. After having accidentally deleted MUSE from my computer (!!), I am now unable to download it again from CC. It says it is already updated, but that is no comfort in this situation. I need to download it. Is there any help to get?
HSPANHS

Thanks Marty!
Sorry, but I use the Mac.
The problem was solved. Adobe has a small piece of software. It deletes all rests of software pieces on the computer. Muse was gone, but evidentally not small files belonging to Muse. The program erased everything, and now CC thought (rightly so) thought I had not installe Muse and allowed me to do so!
Thanks for taking your time to write to me.
Best wishes,
Helge.
21 feb 2014 kl. 16:36 skrev marty11960 <[email protected]>:
Re: How do I download MUSE again after having accidentally deleted it
created by marty11960 in Creative Cloud Download & Install - View the full discussion
Hi HSPANHS,
Look into your controlpanel and see if muse is still there. If so, delete it.
Then you will be able to download it again.
Marty
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6143555#6143555
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6143555#6143555
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6143555#6143555. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Creative Cloud Download & Install at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

How to made usb pen drive a recovery tool....?, how to made usb pen drive a recovery tool....?

As I have downloaded your Recovery Assistant tool on Intel base machine now please describe the whole process to make USB pen drive a recovering tool for my Mac Book Pro as it was pre-install a Snow Lapord OS X.

What OS are you trying to make a bootable recovery for?
10.6 is not available for download and I can't see how you have a MacBook Pro with Retina that came with 10.6.8?
You can either make a recovery disk (which boots & then downloads the installer from the App store). clintonfrombirmingham linked instructions for that.
Or you can make a bootable install disk. First you download the OS from the App store & then use a command to image the installer to a USB disk.
Creating a bootable OS X installer in OS X Mavericks
http://krypted.com/mac-os-x/create-mavericks-installation-media/
10.6 should be on a DVD installer disk which can be copied to a USB disk via another method, ask if you need that.

How to put a recovery partition on the hard drive

How can I create a recovery partition on the hard drive of my laptop. I had to reinstall the whole system, and tried to use the HP recovery software they sent me but it quit when it was about three quarters the way finished. I had to use a copy of windows 8 to put the system back on my laptop. After I got it all straighten out, I updated it to windows 8.1 and it seems like the computer runs a lot faster with windows 8.1 on it. Now I need to find away to install a recovery partition on my hard drive.
Thank You
Garry Crist

When requesting assistance, please provide the complete model name and/or product number of the HP computer in question. HP/Compaq makes thousands of models of computers. Without this information it may be difficult or impossible to assist you in resolving your issue.
The above requested information can be found on the bottom of the computer or inside the battery compartment. Please do not include the serial number. Please enter the model/product information into HP's Online Consumer Support page and/or post it here for our review.
A Recover partition is something the factory places on the computer. It is an image of the factory installation and the software required to restore the computer to a factory like state using that image. You will not be able to create a Recovery partition on your computer unless you use the HP Recovery Discs to return the computer to a factory like state. Please note the HP Recovery Discs and the resulting HP Recovery partition will only contain an image of Windows 8 that cannot be updated to reflect the installation of Window 8.1.
My suggestion is to use the Windows "System Image Backup" utility to create an exact image of the Windows 8.1 partition as it currently is. If your computer developes an issue or you need to replace the hard drive, all you have to do is "restore" the image to the computer. You will need to use an external USB hard drive or other media to store the image. Please see Windows 8.1 Tip: Use System Image Backup for instructions on creating and storing a "Windows - System Image Backup."
If you have any further questions, please don't hesitate to ask.
Please click the white KUDOS star to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

How to install a recovery partition after installing a new Hard drive? and FileVault help.

Hi,
I recently swapped out hard drives and when I did a Time Machine backup to the new drive, I noticed there was no Recovery HD partition for my drive. Is there a way to install it back on my MacBook Pro (Late 2011, running 10.7.4)?
On a slighlty different topic FileVault won't let me encrypt my new HD it says "Some disk formats don’t support the recovery partition required by encryption. To use encryption, reinstall this version of Mac OS X on a reformatted disk."
What formatting does my disk require for FV to be turned on? Currently it is Mac OS Extended (journaled)
If there is a solution to solve both these issues, or any one issue it would be appreciated.

The formatting being referred to is actually the presence of the Recovery Disk.
You can't enable FV2 without a recovery partition being present. The reason is strictly logical: if your entire disk was encrypted, how could you run the unencryption procedure you need to start up? That would itself be hidden behind the encryption. Hence, for FV2 to be able to work, you must have a Recovery disk present.
When you boot up with FV2 enabled, the login screen you see to enter your password is actually running from the recovery disk (invisible to the user). After you enter your password, recovery boots your encrypted partition and logs you in to your account.

How to mount USB & CDROM drives from single user mode - Solaris boot disk?

Hi All,
I need to carry out ufsrestore on a single newly replaced system disk (no redundancy / mirroring) from either USB or CDROM drives from the following steps:
( i ) GRUB => e, e, cdrom –s, Enter, b (boot from Solaris 10 x86 media).
( ii ) Choose menu 1 for Install Solaris Interactive Mode to reach single user mode.Below are the commands that I have tried in single user mode without success:
mount –r –F pcfs /dev/dsk/c1t0d0p0 /cdrom (after unmount Solaris CD)
mount: /dev/dsk/c1t0d0p0 is not a DOS filesystem.
svcadm –v enable smserver
svcadm: Pattern ‘smserver’ doesn’t match any instances
svcadm enable autofs
svcadm: Pattern ‘autofs’ doesn’t match any instances
devfsadm
devfsadm: mkdir failed for /dev 0s1ed: Read-only file system
mkdir /mnt
mkdir: Failed to make directory “/mnt”; Read-only file systemPart of the problem is due to the current READ ONLY filesystems which does not allow the creation of mount point such as /mnt.
I have been able to create both / root (/dev/dsk/c1t0d0s0) and /export/home (/dev/dsk/c1t0d0s0) filesystems with newfs that are awaiting for restore using ufsrestore.
The only option I am left with is to attach a secondary disk to install Solaris 10 on either of them before bring the system to multi-user mode so that service such as volmgt, autofs, volfs are available to access USB & CDROM drives.
Any suggestion on how to resolve this issue?
Many thanks,
Jack

Hi JKGN,
Is the directory a located under the root filesystem. ie /a? Are there any other mount point for say USB drive as well? I am not in a position to try it out right now but will get back
to you soon on whether /a exist or not.
Btw, the last thing I managed to do on this system at the time was added a secondary 1TB internal disk with the intention to restore both / and /export/home data onto this disk while
making use of all the disk device management services such as the following services only available in a fully installed Solaris system (both single & multi-user modes) installed on the
primary disk:
# svcs smserver
STATE          STIME    FMRI
online         Jun_08   svc:/network/rpc/smserver:default
# svcs autofs
STATE          STIME    FMRI
online         Jun_08   svc:/system/filesystem/autofs:default
# devfsadm
# iostat -En
c1t0d0           Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: ATA      Product: SAMSUNG HD321KJ Revision: 0-11 Serial No:
Size: 320.07GB <320072932864 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 41 Predictive Failure Analysis: 0
c0t0d0           Soft Errors: 0 Hard Errors: 5 Transport Errors: 0
Vendor: PHILIPS Product: DVD+-RW DVD8801 Revision: AD21 Serial
Size: 17.54GB <17538875392 bytes>
Media Error: 0 Device Not Ready: 5 No Device: 0 Recoverable: 0
Illegal Request: 10 Predictive Failure Analysis: 0
c2t0d0           Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: JetFlash Product: Transcend 16GB   Revision: 1100 Serial No:
Size: 0.00GB <0 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 7 Predictive Failure Analysis: 0
# rmformat
Looking for devices...
     1. Volmgt Node: /vol/dev/aliases/cdrom0
        Logical Node: /dev/rdsk/c0t0d0s2
        Physical Node: /pci@0,0/pci-ide@1f,1/ide@0/sd@0,0
        Connected Device: PHILIPS DVD+-RW DVD8801 AD21
        Device Type: DVD Reader/WriterHowever, I was disappointed that "iostat -En" has not found the secondary disk (1 TB) even though it was available earlier, for Solaris installation as the only disk on the same system.
As a result, I am left with no option but the need to rebuild this system with only a single primary disk while in single user mode. However, the single user mode that I am in is the
one from Solaris installation disk with restrictive (_cannot create folder for mount point or running disk management utilities_) capability such as those services just covered, compared to one from a completed Solaris installation system with full access to all filesystems and utilities / commands in general.
I would very much value your assistance on how to mount both CD & USB in this restrictive limited Read Only OS (assume that it is running from memory) in order to get complete access to
the blank primary disk so that full restore with ufsrestore could take place.
Thanks in advance,
Jack
Edited by: 797805 on 9/06/2012 04:15

How to Copy USB Recovery Drive back to accidentally deleted Recovery Partition Windows 8

Similar Messages

Maybe you are looking for