How to create a Access Port in ASR901

Hi
I was tried to configured an ASR901 access port for my customer POC in ASR 901 but fail.
It does not support for switchport access VLAN commad .
I have suscessful setup a port-channel in ASR901 to the Alcatel switch and the LACP is up and in bundded state.
The question is how can I configure a access port mode (VLAN 100) in ASR901? The PC will need to
perform a PC Ping test from the ASR901 access port to the ALU Access port via the port-channel that I have configured.
I try to plug in my PC to the port Gi0/4 then run the Ping test from my PC to another PC that connected to Alcatel switch but fail as well.
PC (VLAN 100) Gi0/4 --- ASR901 --(LACP)--ALU --- PC (VLAN 100)
ASR901 configuration
interface Port-channel1
no negotiation auto
service instance 10 ethernet
  encapsulation dot1q 100
  bridge-domain 10
service instance 20 ethernet
  encapsulation dot1q 200
  bridge-domain 20
interface GigabitEthernet0/0
no negotiation auto
service instance 10 ethernet
  encapsulation untagged
  bridge-domain 10
interface GigabitEthernet0/1
negotiation auto
channel-group 1 mode active
interface GigabitEthernet0/2
negotiation auto
channel-group 1 mode active
interface GigabitEthernet0/3
speed 100
duplex full
no negotiation auto
interface GigabitEthernet0/4
no negotiation auto
cdp enable
service instance 10 ethernet
  encapsulation dot1q 100
  rewrite ingress tag pop 1 symmetric
  bridge-domain 10
interface GigabitEthernet0/5
speed 100
duplex full
no negotiation auto
service instance 20 ethernet
  encapsulation untagged
  bridge-domain 10
interface GigabitEthernet0/6
speed 100
duplex full
no negotiation auto
service instance 10 ethernet
  encapsulation untagged
  bridge-domain 10
interface GigabitEthernet0/7
no negotiation auto
service instance 10 ethernet
  encapsulation untagged
  bridge-domain 10
Tq

Hi alexander,
But for function module MAster_idoc_distribute.
What are the parameters i need to pass for Logical systems and what i have to give in the Model distribute .
Can you explain me detail.How the sys knows have to maintain for sender and recevier sys.
As File port new to me.
Regards,
Madhavi.

Similar Messages

  • How to create the Access sequence for the Vendor+material+plant combination

    Hi all
    Please let me know How to create the Access sequence for the Vendormaterialplant combination..
    Whats the use? What its effect in purhcase and taxe..
    brief me please

    Hi,
    you are asked to maintain the access sequence for the tax condition for which you are putting 7.5%.
    goto OBQ1 or img..financial accounting new...global settings.... taxes on sales and purchases ......basic settings.....
    find the tax condition type. see in it which access sequence is attached.
    if there is none then use JTAX used for taxes in India.
    or you can create the similar one for your.
    to create the same goto OBQ2.
    new entry or copy JTAX.
    and assign the access sequence to condition type.
    this will resolve your problem if you just need to assign the access sequence.
    regards,
    Adwait Bachuwar

  • What are message tables and their role?How to create and access them ?

    hi,
    Can any body clarify me about What are messaging tables and their role(use) in DataBase?How to create and access them ?
    Thanks in advance
    Gopi

    If you have doubt that's you have an idea. So, explain your idea please, because I don't see what are "messaging tables".
    Did you say about Oracle database ? Apps ?...
    Nicolas.

  • How to create a Access list on core switch to bloxk all Internet Traffic & allow some specific Internet Traffic

    Hellp Everyone,
    I am trying to create a Access-List on my Core Switch, in which I want to allow few internet website & block the rest of them.
    I want to allow the whole Intranet but few intranet websites also needs access to the internet.
    Can we create such Access-List with the above requirement.
    I tried to create the ACL on the switch but it blocks the whole internet access.
    i want to do it for a subnet not for a specific IP.
    Can someone help me in creating such access list.
    Thanks in Advance

    The exact syntax depends on your subnets and how they connect to the Internet. If you can share a simple diagram that would be much more informative.
    In general just remember that access-lists are parsed from the top down and as soon as a match is found, the processing stops. So you put the most specific rules at the top. also, once you add an access-list, there is an implicit "deny any any" at the end.
    The best approach is to create some network object-groups and then refer to them in your access list. From your description, that would be something like three object-groups - one for the Intranet (Intranet), one for the allowed servers that can use Internet (allowed_servers), and a third for the permitted Internet sites (allowed_sites).
    You would then use them as follows:
    ip access-list extended main_acl
    permit any object-group intranet any
    permit object-group allowed_servers object-group allowed_sites any
    interface vlan
    ip access-group main_acl in
    More details on the syntax and examples can be found here:
    http://www.cisco.com/en/US/docs/ios-xml/ios/sec_data_acl/configuration/15-2mt/sec-object-group-acl.html#GUID-BE5C124C-CCE0-423A-B147-96C33FA18C66

  • How To create a File Port in ALE Settings

    Hi All,
    I want to create a File port, but can anybody help me what are the details have to be updated while creating the Port in WE21.
    Is it i need to mention RFC Destiantion while creating a File port.
    IF not let me know how to configure the logical systems with out giving the RFC destiantion.
    Regards,
    Madhavi

    Hi alexander,
    But for function module MAster_idoc_distribute.
    What are the parameters i need to pass for Logical systems and what i have to give in the Model distribute .
    Can you explain me detail.How the sys knows have to maintain for sender and recevier sys.
    As File port new to me.
    Regards,
    Madhavi.

  • How to create and access Global variable in Microsoft Lightswitch(VB)?

    How to create an integer datatype Global variable in Microsoft Lightswitch 2011(VB) and access it in pre-process query to set value? Can it be accessed and set like Me.Application.<MyGlobalVariable> = 999
    Thnx.
    jajjaar123

    If you want to create integer datatype Global variable in lightswitch, you can refer to (Eric Erhardt) blog
    Create and Use Global Values In a Query

  • How to create an XML Port in we21

    Hi friends,
    Please help me in creating the XML Port in we21.
    what are the inputs I need to pass to create the
    XML File  Port.
    Kindly suggest me
    Thanks in Advance,
    Ganesh

    Hi Ganesh,
    Create a XML port thru Tranx WE21 and send the IDoc to that port system will create an XML file for you of your EDI document
    see this link
    http://sap.wikispaces.com/edi-tx-we21
    XML basics blogs
    /people/tobias.trapp/blog
    https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/4943f2b7-0a01-0010-37af-faff35b2f08c
    REFER THIS THREAD
    http://help.sap.com/saphelp_nw04s/helpdata/en/dc/6b7fa443d711d1893e0000e8323c4f/frameset.htm
    Ports are use to define the way data is send (or received) from another partner (e.g. other system).
    Port type Transactional RFC defines an RFC Destination.
    Port type File defines a file and directory (and a function module that does the record handling for your output file)
    Port type CPI-C defines an SAP R/2 system and transmission parameters.
    Port type Internet, allthough in the system is no longer supported (See SAP note 315083).
    Port type ABAP-PI defines a function module that will do the transmission. This is often used if you want total control over the sending (or receiving) process.
    XML defines a file and directory (and a function module) specific to XML formatted files. The XML-HTTP leaves out the file and can transmit directly to a website location
    thanks
    karthik

  • How to create and access a Virtual Host on the J2EE WAS?

    Hello, I have searched through the Forums and help.sap.com and found a lot of information on how to set up a Virtual Host on the J2EE server but am having issues with it working.
    The goal is to provide a simple virtual host on the J2EE Portal server to host some static image and HTML files. Previously I had stored these files in the standard publicly accessible SAP J2EE folder location /usr/sap/<SID>/JCxx/j2ee/cluster/serverx/apps/sap.com/com.sap.engine.docs.examples/servlet_jsp/_default/root/. This location is resolved to when using the URL <host>:50000 for example.
    The main issue here is that during Portal support pack applications this folder gets wiped out and we have to remember to save off any custom files and folders in this location and replace them.
    I would like to create a virtual host to store these static files (i.e., branding-image.jpg, etc...).
    I have run through the process of creating the virtual host both using Visual Administrator and <host>:50000/nwa but am not able to get the virtual host name to resolve properly.
    The following are the steps that I have taken. Let's assume the standard SAP portal (i.e., xSS, etc...) is running properly on <host>:50000.
    1. create virtual host via Visual Administrator/NWA called 'sapwebserver1' by using the Create Host option (takes on the attributes of the 'default' standard virtual host)
    2. change the root directory for this virtual server to a custom folder at E:/tmp/mimes (where E:/usr is where the J2EE files are all installed), no start files were set up and nothing else was changed in the new virtual host record, no permissions were changed on the /tmp/mimes folder from whatever the default Windows user permissions are normally set, I am using a local Windows  administrator account but I have not seen any reference in the help files or the examples that indicate that any specific permissions updates need to be made on the virtual host root folder
    3. restarted the J2EE server as well as the HTTP Provider service
    4. before updating the company DNS, I wanted to test this locally on the server and so have updated the server's local HOSTS file with a <host IP address>   sapwebserver1 entry
    5. from that server I can ping the sapwebserver1 virtual host name and it resolves properly to the machine's physical IP address
    According to all of the documentation and examples I have seen I should now be able to (from that server) launch a browser and access the static files in the virtual host by referring to http://sapwebserver1:50000/branding-image.jpg for example. This is not working and the browser just brings up a Cannot display the web page error in IE. By referring to the virtual host name sapwebserver1:50000 it's supposed to hit the J2EE server and based on the host name sapwebserver1 realize that it should resolve to the root directory E:/tmp/mimes. This is not happening. Just as a test I have created a copy of the 'default' virtual host and called it sapwebserver2, updated the local HOSTS file for this entry, and tried to see if that would work like the 'default' host. My expectation was that http://sapwebserver2:50000 would behave the same was as http://<host>:50000 but it too fails to resolve just like the sapwebserver1 virtual host refernce.
    Would anyone happen to have any pointers on what to do next? I just want a simple virtual host to be able to serve up some static images and files.
    Thanks for any insight or assistance you might be able to provide here.
    Graham

    This defeats the purpose of trying to centralize SAP-related web resources on the SAP server. Typically IIS/Apache or other non-SAP servers are under the control of IT and not the SAP BASIS group.
    We simply would like to have a centralized location to store static web files so that they are not overwritten during Portal support pack applications.

  • NAM 5.1 How to create Application with port range from cli?

    Hello,
    I can create new Applicaion with port range from GUI, but I can not do it from CLI
    If I do it by CLI as a:
    nam# application
    nam# name mkst-cur-A
    nam# match udp 16001-16009
    nam# exit
    then
    nam# show application app-tag 268435576
    custom:120 (268435576) mkst-cur-A
      udp 16001
    nam#
    But if I do it by GUI and than
    nam# show application app-tag 268435576
    custom:120 (268435576) mkst-cur-A
      udp 16001 - 16009
    nam#
    How to do it by CLI?

    Hi Alexey,
    Sure, the function you're looking for is in the ANALYSIS panel under the "CUrve Fitting" palette-- it's called "Linear Mapping".  You will need to create the desired X channel prior to calling this function, though, so you will probably need to use the ANALYIS function "Generate Numeric Channel" in the "Channel Functions" palette.
    Brad Turpin
    DIAdem Product Support Engineer
    National Instruments

  • How to create an Access Point with Two MI424WR (GigE for Verizon FiOS) Routers?

    I understand that these routers are fairly new and I cannot seem to find hardly any information on them.  I have a fairly large home and I just happen to have two MI424WR's Gig E routers.  One is my main and the other I would like to create into an Access Point.  Has anyone done this with these routers?  I have found plenty of previous information on previous routers similar to these, but I have yet to find any instructions on how to do this with these routers. 
    Please help!
    Mark
    http://www.actiontec.com/products/product.php?pid=214

    How are you going to connect them?  cat5 or coax?
    cat5 instructions:
    Can I use my wireless or an extra router along with the Verizon provided router?
    coax instructions:
    Can I get an ethernet connection in a room with only coax?

  • How to create and access cookie with in iView ?

    Hi,
    I have created iViews using .Net PDK for SAP.
    Is it possible to create a cookie using code of iView and use this cookie to access an external application.
    Regards,
    Vikas Khandpur

    U cud add this code to the java iview:
    setting a cookie:
    Cookie fCooky = new Cookie("flag","false");
    response.addCookie(fCooky);
    fCooky.setPath("/");
    Reading the cookie:
    Cookie[] cook = request.getServletRequest().getCookies();
    for (int i = 0; i < cook.length; i++){
    Cookie cc = cook<i>;
    if(cc.getName().equals("flag")){
       response.write(cc.getValue()toString());
    Iam not sure how u wud do it in a .NET Iview.
    Sry!
    Regards,
    P.

  • How to create logs(access logs, debug logs..)

    Hi,
    I need to catch the exception and create the log file with the exception message in sun access manager. I am using com.sun.identity.log.Logger for doing it. we have methods to create the logRecord without ssotoken, so when I am trying to create a log file without the ssotoken nothing is happining i:e no log file is created, the same thing I am able to do with by passing ssotoken. my question in the application if we get any exception before getting the ssotoken then how to log the message into the log file.
    please help me...
    Thanks
    tatineni.

    You may want to use the "Shotdown hooks" API -- http://java.sun.com/j2se/1.4.2/docs/api/java/lang/Runtime.html#addShutdownHook(java.lang.Thread).

  • How to create guest access in wireless by WISM and WCS and ACS?

    dear sir
    i neeed to know the steps of how we can make guest access to our network like hotels by using our WISM v 7.0.220 and wireless control system and ACS ?

    You need to define your requirements a little bit. The WLC can do WebAuth and an employee can access either the WLC or WCS to put in the username and password credentials, but you would need to figure out what's best for you.
    Here is a support doc that you can reference.
    https://supportforums.cisco.com/docs/DOC-13954
    Sent from Cisco Technical Support iPhone App

  • How to create package access MXML component?

    Hi
    In ActionScript we can create an internal class which can be referenced by the classes in the same package.
    How can we create the MXML component which can be referenced by the others in the same package?

    Packager Links https://forums.adobe.com/thread/1586021

  • Step to create new access sequence

    Hi SAP gurus,
    Can anyone teach me how to create new access sequence?
    I am zero knowledge on this. Need help from A to Z.
    I only know how to maintain the pricing VK11.
    If the info already discuss before, kindly need ur kindness to link it for me...

    Hi you can define access seq. in T-code v/07
    You can define prices, discounts, and surcharges at various levels. Each level
    is defined by a condition table. An access sequence consists of one or more
    condition tables. The order of the entries in an access sequence defines the
    hierarchy of the various levels. The system determines the condition records
    in the sequence specified.
    Within each access of an access sequence, you can specify the document field
    or source field with which an access is performed. You can make access
    dependent  on requirement to avoid unnecessary access, thus reducing the
    system load.
    For better understanding go through pricing procedure.
    Reg pricing procedure.
    1. Use transaction code v/07 to create a access sequence and assign tables based on which you want to carry on 
        pricing as accesses.
    2. Use transaction code v/06 to define condition type. It can be for base price, discount, freight etc.,
        (Do assign relevant access sequence)
    3. Use transaction code v/08 to define pricing procedure.
    4. Assign this to your relevant sales area+ dpp+cupp.
    I hink it will help u.
    Best Regards
    Sainath

Maybe you are looking for