How to determine the mac address of an ATM interface

Hi All,
I have a router with an SHDSL controller. I am doing some troubleshooting and there seems to be an ip address conflict on the layer  2 shdsl network.
I am trying to figure the mac address of my atm sub interface. An ip address is set on the controller.
interface ATM0/0/0.1 point-to-point
Does  someone know the command for finding it?
sh arp does not show the interface itself.
Can you please help.

Invalid command
#sh atm ?
  arp-server          ATM ARP Server Table
  bundle              ATM bundle information
  class-links         ATM vc-class links
  ilmi-configuration  Display Top level ILMI
  ilmi-status         Display ATM Interface ILMI information
  interface           Interfaces and ATM information
  map                 ATM static mapping
  pvc                 ATM PVC information
  route               ATM route
  traffic             ATM statistics
  vc                  ATM VC information
  vp                  ATM VP information
The command is not available :(

Similar Messages

  • How to get the MAC address of the additional 10G NIC with ILO command line

    how to get the MAC address of the additional 10G NIC with ILO command line?
    thanks.
    This question was solved.
    View Solution.

    Hi Bruce,
    Out from what I can find on this network card is it not possible to get the mac address without a OS. I would recommend you to get/burn a Linux/Ubuntu live CD/DVD and run a Ifconfig in there.
    Hope it helps you.
    Best regards
    Zincas
    I work on behalf of HP

  • How to change the mac address of thunderbolt to ethernet adapter?

    Hello everyone,
    I am using Macbook pro retina display 2013 version. I have bought a thunderbolt to ethernet adapter in order to connect my Macbook to LAN. But in my area there is a shared line and I have to clone their mac address to my Macbolok. I could not change the mac address of my thunderbot to ethernet adapter. Can anyone please tell me how to change the mac address of thunderbot to ethernet adapter step by step??
    Thanks in advance.

    Open terminal and type the followings;
    1) sudo ifconfig bridge0  ether xx:xx:xx:xx:xx:xx(it will be your new mac address)
    2) Type your password to confirm
    3) ifconfig bridge0 |grep ether (to see if change is successful)
    PS: *This should with your thunderbolt adapter, but its not working usb to ethernet adapters without installing required drivers.
           ** You may need to do these steps every time you boot your mac.

  • How is that the MAC address (BIA : Burn -in -Address) not yet exhausted?

    How is that the MAC address (BIA : Burn -in -Address) not yet exhausted? IPV4 is exhausted and we are moving to IPV6!

    MAC addresses are 48 bits long. That is 65536 times the IPv4 space. IP addresses need to be globally unique while MAC addresses only need to be unique on their local LAN segment (LAN/VLAN).
    Here is a good link explaining it more in detail:
    http://blog.michaelfmcnamara.com/2013/03/are-we-running-out-of-mac-addresses/
    There is also a link there that suggests some edits to the 24-bit OUI assignments:
    http://www.ietf.org/proceedings/86/slides/slides-86-iab-techplenary-5
    Daniel Dib
    CCIE #37149

  • How to read the MAC address of a BT device ?

    How to read the MAC address of a BT device ?
    Thanks,
    Ionut

    I should've added more details ; I'm interested to find out, from an IPhone app, if a certain BT device is in the proximity of the phone. The verification involve checking the MAC address or the name of the device.
    Thanks,
    Ionut

  • How to find the MAC address of iPod Shuffle?

    Hi,
    I need to add MAC address of iPod shuffle to the wireless router. Does anyone know how to find the MAC address of iPod shuffle? I would appreciate your help! Thanks.

    Thanks for reply. So then I am not sure why my laptop is not recognizing iPod shuffle when it is connected through USB cable. I don't see DEVICES option under iTunes..so can't sync the music.

  • How to find the MAC address of my iPad2?

    My WiFi hot spot has MAC address filter for better security.
    But I cannot find the MAC address of my new iPad2.

    If you need to setup wifi to start the MAC address with iPad, try  the http://www.ipad-tablet-help.com/2010/03/how-to-find-ipad-mac-address.html   to find it out.  Works for iOS5.

  • How to get the MAC address of a PXI in a dll

    Hi,
    I am looking for a way to get the MAC address of a PXI RT controller. I know that there is a VI to do this, but I am looking for a solution for a dll (C-Code).
    I use the "Call library node" to call this dll and want to make sure that it is only used on a specific PXI.
    Since the VI provides the functionality, I am wondering if it is also available to be called from C-Code?
    Thank you,
    Christian
    Solved!
    Go to Solution.

    ChristianEC wrote:
    Hi,
    I am looking for a way to get the MAC address of a PXI RT controller. I know that there is a VI to do this, but I am looking for a solution for a dll (C-Code).
    I use the "Call library node" to call this dll and want to make sure that it is only used on a specific PXI.
    Since the VI provides the functionality, I am wondering if it is also available to be called from C-Code?
    Thank you,
    Christian
    If it is available in LabVIEW it is probably available in CVI, which you could then build into a DLL (if there isn't one available already).
    CLA, LabVIEW Versions 2010-2013

  • How to get the MAC address of  other hosts in local net

    1. Is there any kerner or user function to get the MAC address of other hosts in local net?
    2. ire_route_lookup() can only lookup MAC in routing table(arp -a),Is there any way to enable it to find out all MAC of hosts in the local net?
    Best Regards
    Hann

    ChristianEC wrote:
    Hi,
    I am looking for a way to get the MAC address of a PXI RT controller. I know that there is a VI to do this, but I am looking for a solution for a dll (C-Code).
    I use the "Call library node" to call this dll and want to make sure that it is only used on a specific PXI.
    Since the VI provides the functionality, I am wondering if it is also available to be called from C-Code?
    Thank you,
    Christian
    If it is available in LabVIEW it is probably available in CVI, which you could then build into a DLL (if there isn't one available already).
    CLA, LabVIEW Versions 2010-2013

  • How to find the mac address

    I am trying to connect my iPad to my Netgear router and activate the user list. Amazingly the router status does not show the iPad although it is connected. I used the mac address which I found under settings --> general --> info. I used the WLAN address to add it to the routers user list. Unfortunately it did not work. Any idea which other address I could use and where to find it on the iPad. Thanks for the help.

    Does it show under Options | Status as a WLAN Mac Address?
    If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
    Remember to resolve your thread by clicking Accepted Solution.

  • How to read the MAC address of a connected client?

    Thx alot for any help.
    Jochen

    Hi,
    I tried this on my aix box. The interface is called en1. The MAC variable is in decimal format (base 10), but the output of lscfg is an hexadecimal address.
    If you can start with this...
    Do not even try to reply that you are using windows please !
    Regards
    Laurent
    PS: due to bug 3798918, it will not work with sqlplus 10.1.0.2.0
    SQL> var mac number
    SQL> host exit `lscfg -l ent1 -v | grep 'Network' | cut -c37,38 | sed 's,^,16i ,;s,$,p,' | dc
    SQL> exec :mac := &_rc;
    SQL> host exit `lscfg -l ent1 -v | grep 'Network' | cut -c39,40 | sed 's,^,16i ,;s,$,p,' | dc
    SQL> exec :mac := :mac * 256 + &_rc;
    SQL> host exit `lscfg -l ent1 -v | grep 'Network' | cut -c41,42 | sed 's,^,16i ,;s,$,p,' | dc
    SQL> exec :mac := :mac * 256 + &_rc;
    SQL> host exit `lscfg -l ent1 -v | grep 'Network' | cut -c43,44 | sed 's,^,16i ,;s,$,p,' | dc
    SQL> exec :mac := :mac * 256 + &_rc;
    SQL> host exit `lscfg -l ent1 -v | grep 'Network' | cut -c45,46 | sed 's,^,16i ,;s,$,p,' | dc
    SQL> exec :mac := :mac * 256 + &_rc;
    SQL> host exit `lscfg -l ent1 -v | grep 'Network' | cut -c47,48 | sed 's,^,16i ,;s,$,p,' | dc
    SQL> exec :mac := :mac * 256 + &_rc;
    SQL> col mac for 9999999999999999999999999
    SQL> print mac
                           MAC
                   10021178476

  • Determine LAN MAC-address knowing only the model and serial number

    Laptop Toshiba SN 96592614G
    Is it possible to determine the MAC-address of the network card, knowing only the model and serial number of your laptop?
    How to refer the matter to the addicts Toshiba.

    Knowing the serial number you can check the notebooks details here:
    www.toshiba-tro.de/unitdetails
    but there are no informations about the mac adress... maybe an Toshiba authorized service provider woudl be able to provide an info about that ...

  • How can I get the MAC address

    My machine has two NIC's. I need to add another network interface, however when I do so it gets assigned to the same MAC address as the interface in use. Why is that and how can I determine the MAC address of the other card to be able to assign it to the new interface?
    thanks

    If necessary, change the value of local-mac-address? as follows:
    eeprom local-mac-address?=true
    When you reboot the system, the interfaces with factory-installed MAC addresses now use these factory settings, rather than the system-wide MAC address. Interfaces without factory-set MAC addresses continue to use the system-wide MAC address.
    [http://docs.sun.com/app/docs/doc/816-4554/eyprp?a=view]

  • How do I find the MAC address of a CLIENT ACCESS POINT created from the FILE SERVICES ROLE

    I have several Client Access Points created within the clustered File Services Role.  The only way I seem to be able to determine the MAC address of each of these, is by visiting the DHCP server.
    Does anyone know if there is a way of reporting on this from the server (active node) itself?  I have tried ipconfig all, checked the properties of the CAP in the FCS console etc.
    Many thanks.
    Kathleen Hayhurst Senior IT Support Analyst

    Hi,
    As far as I know there have no original option for query all the CAP MAC address, may you can create a PowerShell command then filter the configuration result, you can ask
    in PowerShell forum for the further help.
    More information:
    PowerShell forum:
    http://social.technet.microsoft.com/Forums/en-US/bf0e249b-a9f3-4bef-a536-c210b3f09340/powershell-script-to-alert-on-failed-system-state-backups?forum=winserverpowershell
    The related KB:
    Failover Clusters Cmdlets in Windows PowerShell
    http://technet.microsoft.com/en-us/library/hh847239.aspx
    The related article:
    PowerShell for Failover Clustering: Frequently Asked Questions & Enabling CSV
    http://blogs.msdn.com/b/clustering/archive/2009/05/23/9636665.aspx
    Hope this helps.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Windows 7-8.1 Can not change the MAC Address on wifi and cannot load login page in public HotSpot.

    Windows 7-8.1 Can not change the MAC Address on wifi and cannot load login page in public HotSpot.
    Adapter: Ralink RT3070 Chipset wifi adapter
    Tested: os Windows 8.1 Professional
    Hot Spot: 802.11b
    The first problem windows 7-8.1 got IP adress and connect he public HotSpot  but  cannot load login page or any other page. It does not work with it.
    The second problem Wifi canrd/configure/Advandes (No network adress change function).Tested with the default windows driver and the ralink rt 3070 driver the same problem.On windows XP the same function the same driver works perfectly.
    multiple users to have expressed interest in the problem But Microsoft not corrected the problem window7-8.1 10?
    lizardsystems.com/wiki/change_mac_address/faq/change_mac_address_in_windows_7
    blog.technitium.com/2011/05/tmac-issue-with-wireless-network.html
    superuser.com/questions/519189/how-to-change-the-mac-address-in-win-8-to-spoof-a-roku-player-through-a-wifi-spl
    social.technet.microsoft.com/Forums/windows/en-US/59e07df3-471c-499e-ad5f-e7cb507595df/cannot-change-mac-address-in-windows-7-driver-has-option-doesnt-work-neither-does-regedit-ms?forum=w7itpronetworking
    networksteve.com/windows/topic.php/CANNOT_CHANGE_WIRELESS_%28SPOOF%29_MAC_ADDRESS_ON_WINDOWS_7/?TopicId=16810&Posts=1
    On windows XP or linux have a MAC adress Change function  allow 00 mac adress and another normal mac adress range.On windows 8.1 all Mac changer program dont work.This 2,6,A,E on second adress are not vaild Mac adress. You simply can not use normal MAC
    addresses on windows 8.1.When i connect the usb the Pc windows 8.1 recognizes the adapter but the default  driver and the downloaded ralink driver the same problem.On windows xp the current driver works perfectly have (Local Mac Network Adress) funktion
    and works with the 802.11b hot spot.I got the internet my PC and laptop too public HotSpots and another wifi HotSpots if wont work correctly i can not use neither the windows 7,8,8.1 or 10. Many users have expressed interest in the problem more forums.
    The 3. problem im tested in virtualbox the windows 7 and 8.1 on 8.1 (on the blue wifi platform) not show correctly the signal strengh. On windows 7 show this correctly.The windows 7-8.1 Configure/advanced the advanced options on Ralink 3070 the default (windows
    driver) somehow downgraded function is less than for Xp. Configure/advanced the advanced options (needs to be upgraded in the future) because it does not advance but rather regressed.
    Today it is very common these wi-fi technology increasingly used (hotels,Public Hots Spots,Internet coffe,) growing free bublic wifi projects. The wifi funktions on windows  need debugging and modernize.The quality of Wi-Fi is now the operating system
    is now a thing order which is not good then the operating system is unusable.

    Hi,
    For changing the MAC address for Windows 7 is designed with some limitation, we cannot get over it. Thanks for your understanding.
    Under Windows 7, the possible range of spoofed addresses for wireless adapters that can be set is limited.  To be used by Windows 7, a spoofed MAC address should have 0 as a least significant bit (unicast) and 1 as a second least significant
    bit (locally administered) in the second nibble.  Thus possible values for the second nibble are limited to 2, 6, A and E.
    In other words 
    MAC address:  “XY-XX-XX-XX-XX-XX” “X” can be anything hexadecimal.  The hexadecimal “Y”, written in binary format, is  Y:  “kmnp”,  where “p” is the least significant bit; 
    p=0 --> unicast;
    p=1 --> multicast;
    n=0 --> globally assigned MAC;
    n=1 --> locally administered;
    So, actually MAC can be changed  to any combination in which p=0 and n=1;
    “Y” can be 2, 6, A or E.
    So the possible MAC addresses in Windows 7 for wireless adapters:
    X2-XX-XX-XX-XX-XX
    X6-XX-XX-XX-XX-XX
    XA-XX-XX-XX-XX-XX
    XE-XX-XX-XX-XX-XX
    For the wifi hotspot issue, please check this blog to see if it can be helpful.
    Windows 7 Connectivity Problems in Public Hotspots
    http://blogs.technet.com/b/patrickr/archive/2010/07/28/windows-7-connectivity-problems-in-public-hotspots.aspx
    Kate Li
    TechNet Community Support

Maybe you are looking for