How to disassemble the Camileo S10?

I would like to hack the S10 to solve 2 problems:
1) Put a wide angle adaptor
Actually it is almost impossible, but removing the plastic part in front of objective allow to access to cylindrical part of it and fix a wide angle adaptor
2)I need to fit the S10 on a RC model to keeping the camera in horizontal position instead of vertical.
I successfully start to disassemble the camera removing the plastic black middle where the battery is located.
I stop because I have no ideas how to unmount the video display
Anyone have a link to Toshiba Service manual of the Camileo S10 or have an idea how to dissasemble it ?

Hi
I think disassembling a Camileo is not so easy and should only be done from an expert.
If something is wrong with your camera you should go to the nearest authorized service provider. The technicians can disassemble it for you and they have such service manuals I think.

Similar Messages

  • Where Can I buy another battery for the Camileo S10?

    Hi.
    I would like to know if are there some compatibility batteries for our Camileo S10.
    Thanks.

    Hi!
    Have you contacted an authorized service provider? They can order all original Toshiba parts and maybe for the camcorders too. Just ask for this. :)
    And maybe you can find on eBay some batteries for the Camileo camera. Check this!
    Bye

  • Tecra A8: How to disassemble the keyboard?

    I'd like to disassemble keyboard in my Tecra A8. Is there any disassembly guide on the web?

    Hi
    I dont think that you will find any manuals which describe the keyboard removing procedure. Such manuals are not official documents and only for the service partner usage.
    But in my knowledge the removing of the keyboards is not very difficult.
    There should be a thin cover above the keyboard. This cover masks 2 screws which secure the keyboard. You have to remove the cover and the screws careful.
    Then it should be possible to remove the keyboard.
    But be careful, the keyboard is connected with the short, flat cable to the main board.

  • How to use the Camileo H30 with Power Supply

    Hello
    First: excuse my english, im from germany ;)
    I have a Camilio H30. its was boughted used. I only got the camcorder & the original battery.
    no extras (like usb cable or original power supply)
    what i want: i need to film over some hours. The Battery cant make it. so i wanna use it with a power supply but when i put it in (throughh the mini usb a connector) the camcorder goes to charing mode (no actions are possible) but i want to use it fully functionality when power supply is connected.
    how do i handle it ??
    i got a power supply with 5V an 2,25A , i think its enough... or not??
    The Label on the bottum side from the camcorder tells me 5V 2A....
    Thanks 4 helping me :D
    greetz

    oh ok i thought this is possible because in the main manual at the part when the display icons being explaind they show a full, half-full, emtpy- battery and a power connector icon. they call it "gleichstrommodus" sorry i have only the german manual. in english it should be co-corent flow mode or ac power mode.
    im looking for a way to make the cam work with power supply only. i dont want to charge or even use the battery because i film over few hours ago and for that i dont need it.
    my old dv cam works when the battery was plugged out with ac adapter only. thats very nice for me.
    whatever. if this is not possible i sell this cam and buy another one ;)
    thanks for your help !

  • How to disassemble AG2712A

    Does any one know how to disassemble the AG2712A ?
    Haven't found anything about this topic yet.
    No comments about void warranty etc. needed as I do not care

    Look behind there are holes with screws.

  • How to disassemble AG240 2PE

    Does any one know how to disassemble the AG240 2PE ?
    Haven't found anything about this topic yet.
    No comments about void warranty etc. needed as I do not care

    Please refer to the steps below:
    1. Place the system horizontally on a flat and steady surface. Locate the two
    screws that secure the stand. Unlock them and keep them for later use.
    2. Push to remove the stand carefully and set it aside for later use.
    3. Locate the ODD and its emergency eject hole.
    4. Insert a pin or unfolded paper clip into the hole and push the pin firmly until the disk compartment opens.
    5. Pull out the disk compartment and carefully detach the front bezel hooks.
    6. Push the disk compartment gently backwards until it closes.
    7. Locate the five screws that secure the rear cover. Unlock them and keep them for later use. Pull to remove the rear cover carefully and set it aside for later use.
    8. Locate the screw that secure the rear i/o cover. Unlock it and keep it for later use.
    9. Remove the rear i/o cover carefully and set it aside for later use.
    10. Locate the three screws that secure the metal shield. Unlock them and keep them for later use.
    11 .Push to remove the metal shield carefully and set it aside for later use.

  • Camileo S10 - how to change the aspect ratio to 16:9

    Does anyone know how to change the aspect ratio when making movies with the arcsoft software included with the S10!!!!!
    Won't let me select 16:9 only 4:3!!!
    Not sure why as when you play the recording back directly through the telly it does it in 16:9 so I know it's being recorded in the right ratio!!

    You cannot change the aspect ratio because you record at full hd 1080. The S10 records in format 1440/1080 at full hd, wich means 4/3. The S10 is not capable to record in full hd at 1920/1080 (this is 16/9 full hd). It is simple:
    Camileo S10 record 1440 pixels on horizontal and 1080 pixels on vertical. The aspect ratio is 4/3.
    Answer for your question: if you want to see in 16/9 format use HD2 (720p) for recording.
    Bye.

  • Camileo S20 - How to display the date and time

    Hi, to all. I have got as Christmas present the Camileo S20 and I am not able to display the date and time at video. In manual is no mention about this, just how to set the correct date and time. But what is intention of setting the date and time into camera, if it is not possible to display them on video ?

    Hi,
    of course, I did it repeatly, it is written in my question above. I am not stupid.
    This question is aimed to owners of camera Camileo S20 and also Camileo S10 - Camileo S20 is derived of Camileo S10, may be any of them discovered the way how to get the date and time into video.

  • Camileo S10 Camera does not remember the image-stabilizer setting

    Hello Forum reader,
    Is it normal that my Camileo S10 Camera does not remember the image-stabilizer setting?
    I mostly use the 720px setting and stablilizer on, but after the camera is turned off the stabilizer is off again.
    Greetzz.. Ben

    Hi
    This might be possible.
    I remember that the focus does not work if the stabilization has been enabled
    So maybe its an intention of the manufacturer that the stabilizer would be disabled again.
    Greets

  • How to hack the S10-3T bios for deleting hardware whitelist?

    I plan to install a 3g+GPS minicard module on my s10-3t, but it seems that the bios has a lock on the allowed hardware to be installed on the machine, called while list. how to remove this restriction?
    I plan to add this card:
    http://item.taobao.com/auction/item_detail-db2-3a2280f74b702119f80594b7c38412af.htm

    Maybe...MC8781 has another hardware ID....
    Intel(R) 82801GBM/GHM (ICH7-M Family) Serial ATA Storage Controller - 27C4
    hardware ID:
     PCI \ VEN_8086&DEV_27C4&SUBSYS_27C48086&REV_02
    PCI \ VEN_8086&DEV_27C4&SUBSYS_27C48086
    PCI \ VEN_8086&DEV_27C4&CC_01080
    PCI \ VEN_8086&DEV_27C4&CC_0101
    SUBSYS? how to hack the SUBSYS? I want to try
    and this picture is my MC8781's all of the hardware ID
    Link to picture;
    http://im1.shutterfly.com/media/47a0dd10b3127ccef9ebfbf56b3e00000030O00AbN3Lli0aMmYPbz4E/cC/f%3D0/ps...
    Moderator note; picture(s) totalling >50K converted to link(s) Forum Rules

  • How to locate the S/N for the MSI Eclipse without disassembling the whole pc

    I am hoping there is a way to locate the serial number for my MSI Eclipse SLI mobo without disassembling it from the pc case (which would require disassembling the ENTIRE pc.
    Does anyone know if there is a way to do this - needed apparently to start a tech support call with MSI - from software or by some other method?
    Is it located anywhere but the rear of the mobo?

    Quote from: HU16E on 09-April-09, 14:43:41
    If you still have the original packaging, it should be with the UPC (barcode) information. Otherwise, it is on the bottom of the board.
    AH! I do have the original packaging... havent tossed it yet (thought Id hold onto it in case of RMA .. which is looking more likely). But I didnt think it'd be in the packaging!
    Thanks Hu16E!!

  • Camileo S10 - 16/9 recording at FULL HD

    I have the same problem with friend *rodarko* ([m-169634] ). I have seen his thread, but nobody since now have found a solution. I will try to desribe my exact problem.
    When I record at 16:9 full HD everything seems ok. But when I try to play it on my computer with Arcsoft player, some files are played 16:9 and some others are played 4:3.
    I have made a lot of tryies but the only thing that I have found out is that usually the files that works on 16:9 format, are not the first 5 that I have record. So If I record 4 or 5 or 6 (I do not know why) files, then the next files can be played on 16:9.
    This does not hapens all the times. My camera is Camileo S10 and my card is Kingston 8GB HC (SD6/8GB).
    I wanter why TOSHIBA didn't found any solution, and ofcourse I wanter why they have put the following message (This thread is locked - replies are not allowed.)on the same answer of user rodarko!
    Any way please if you know anything give me an answer. Thank you

    I had similar problem ..... all videos shot in full HD (on my Camileo P30) but some of them on windws were reported as they were shot in 1440x1080.(4:3) and some as 1920x1080
    To solve that you must know how windows system works.
    By doubleclicking an AVI (or opening it by an editing software or player) background process will try to decode such video. Such process is not part of editing software or player, it is part of windows.
    For proper decoding such process will take some infos from AVI file and will try to load apropriate codec for proper interpretation of file stream. When codec is found it will be loaded and used to decode file stream into video and audio streams and those streams then will be returned to host application (editor or player).
    Today, on average computer you can find tons of codecs. On my own ther is over 130 for different file formats.
    You also should know that some codecs avaliable are not finished completly or doesn't support all possible variations of file formats. (new header sections etc)
    To be capable to chose right codec from the bunch windows use some kind of flag called MERIT which is associated to each codec. So codecs with MERIT_VALUE='DO NOT USE' will never be used while codecs with MERIT_VALUE='Prefered' or 'above prefered' will mostly like used.
    The key point of problem from topic and all other problems related to corrupted video or video doesn't load in editor (or player) is MERIT number of probably incomplete (or old) codec.
    If MERIT of such codec is high then other (maybe newer) codes with MERIT set to normal will never get chance to load. To fix that you have several options. One could be to uninstall old or problematic codec. It is easy if codec came as single unfortunately most of codecs come in packs. Removing complete pack is not solution since other codec could be good and are used for other types of videos.
    The best way is to manually change MERIT value for problematic codec to value 'DO NOT USE'.
    To do that easy you'll need simple GRAPH STUDIO. It is small application which comes with KLite codec pack. (maybe it is available as standalone too or with other codec packs too).
    When you start it just drag'n drop an AVI file into it and it will automatically build the graph for it. Graph is network of nodes where each node represent one of used codec for interpretation of used file.
    Remember, graph auto-created here will be exact the same as windows creates in background when some editor or player opens file.
    Usually, AVI file has FILE SOURCE node connected to AVI_SPLITTER node which separate audio and video streams from source file. It is then connected to some video decompressor and audio decompressor which are REAL CODECS. Play button alows to test the graph. If video plays fine then everything is ok but if something is corrupted or video is not in right aspect then you have to do following:
    1. To try ffdshow codec you'll have to select and delete your video codec from the graph
    2. Manually insert ffdshow video decoder node (Graph->Insert filter->ffdshow video decoder)
    3. connect it in the graph as your previous deleted node was connected (stream0 from AVIsplitter to IN of ffdshow node and OUT from ffdshow node to IN of your video renderer)
    4. test such graph by playing it
    This is just a test and will not reflect any changes in windows. If now you get your video properly works you'll have to change the MERIT of codec you are replaced by ffdshow.
    To do that:
    1. Close graph editor
    2. Reopen it and again drag'n drop your AVI file into it
    3. Remember the name of node you want to replace with ffdshow
    4. Find it in the list of all filters installed on the system (click Graph->Insert filter and find it in the list of all filters then just select it and click button CHANGE MERIT and chose DO_NOT_USE)
    5. Also in the same list find ffdshow video decoder, select it and turn on check box FAVORITE FILTER (you may also want to increase it's merrit)
    Now close the graph editor. Open it agin and drag'n drop same AVI file. If auto-created graph now contains ffdshow video decoder, everything is fine.
    If you get some other codec (it is possible if you had installed let say 4 codecs for H264 video.... you disable only one, 3 are still available and some of these could have larger MERIT value than ffdshow. Don't worry, just test graph with such codec. It is possible to work fine. If not disable it on the same way you did with previouse.)
    Graph Studio has many interesting options you can play it like performance testing, experiment with your own graphs making outputs goes to disk instead of screen etc. You can also sve your graphs and use it ie. for conversion from one format to another etc.
    I hope this help.
    At the end sorry for my English, it is not my mother tongue language.

  • Problem charging Camileo S10

    Hi all Toshiba users!!
    I've just bought a Camileo S10 camera, and it looks apretty nice, small and light. But it doesn't seem to charge the battery, neither power on. Here's how I've proceeded:
    1) I removed the insulant from the battery, and put it again, closing the case.
    2) I plugged it in with its own charger, which uses the USB connector.
    3) Circle LED around the "Record" button lights on (but doesnt blink as stated in manual).
    4) When 5 minutes pass, the LED powers off and never lights on again.
    Is this normal behaviour? Because when I try to power on the camera, it just does nothing. I tried flipping the LCD screen and also tried with power button, with USB charger disconnected. Camera doesnt react at all. When I power on with charger connected it works correctly.
    Thanks for your help!
    Message was edited by: m0sk4

    I've exactly the same charging problem with my new S10 camcorder.
    I've removed the insulating film from the battery, but when I insert it again in the S10 and I plug the charger, the LED light doesn't blink: it just lights on (in red) for a few minutes and then simply lights OFF without ever charging.
    Even with the charger connected, i couldn't power on the camera.
    How do you solved that problem?
    Did you find a solution, or you just asked your local dealer to exchange a supposedly damaged item?
    Please, let me know how you did handle that.
    Thanks.

  • How to view the source code for Native Method

    hi
    i am using some native methods in to my code ;
    can anybody tell me how to view the source code for the same ;
    nik

    Buy/acquire a C/C++/assembly code disassembler and run the shared library through it.

  • Camileo S10 - Arcsoft doesn't recognize any files on SD card & internal memory

    I have just bought a Camileo s10 camcoder.
    So far i was satisfied with the product till i connected it to my pc (vista fully compatible with recommendations).
    I installed the Arcsoft software but i never got any file imported because *the program recognised both sd and internal memory as empty*(i could play the files in the camera's player as well as from my pc's card reader ).
    I used other similar suites with no luck.I then tried to format the sd hc 8gb card and restore my files but unluckily i noticed *the video/foto files were not recognised, at that time, even from the camera* .
    Another serious concern is that i had an hd(720p) .mov file from a trailer in my memory card and the camera could not see it (+i wanted to use the camcoder as a high def player connected to my sony full hd tv+).
    I have searched for answers almost anywhere but so far i got no response

    Actually thanks for the advice.I tried those you mentioned and i finally(partially at least) found out that in the sd card and internal memory folders *there where 2 folders* with the same name(100MEDIA.. something)
    One was recognised as an application and the other as a folder.The folder was a hidden file permanently so i supposed this was the reason so my first concern is answered.I found it really weard though!
    I made the format inside the camera.You mentioned a higher class card.Would this improve something specifically?I observed that i have class 4 SD hc.
    *My main worry now is to recognise the recording format of this camera so i can convert other video formats to it.And so far nobody seems to know as everybody is interested in editing recorded videos and not in reproducing.
    Thank you for your answer

Maybe you are looking for