How to discover lwapp hostname via snmp virtual WLC

Hi there,
we recently installed a virtual WLC and configured some LWAPP access points. I want to monitor the status of the WLC and also of the access points. Using the airespace mib or lwap-ap mib I can monitor operational status and the number of associated clients. The only problem I have at the moment is that I can't recover the hostname, mac address or ip address to identify the access point. Does anybody knows which mib or oid to use to identify the access point?

Similar Messages

How to restart base station via SNMP ?

How to restart airport extreme via SNMP, with snmpwalk for example ? I can get a lot of information from base station with snmpwalk and airport-mib but still mystery what to poke when I want reboot base station over network.

You are likely forgetting a step.
Open AirPort Utility
Click on the Time Capsule icon
Click Edit in the small window that appears
Now click the Base Station menu.....top of the screen....not the Base Station "tab" in the center of the screen
Click Restart

How to reset Dot11Radio interface via SNMP

Hi guys,
Please tell me how i RESET my AP's radio interface via SNMP? It's mean down and up right behind sb.
I'm using several SNMP commands for manage to our Cisco's. But I'm unsuccessful at this.. Please help me. Thakns.

Isn't there any response? isn't there any Cisco Specialist at there???

Interface errors (crc, in/output, collisions etc.) via snmp

Hi,
I'm trying to understand how to get interface errors via SNMP. I do get stats via SNMP for ifInErrors / ifOutErrors etc, but I'm trying to get output via SNMP for the errors visible via the 'sh int x' command - CRC errors, input / output errors, collisions, runts. giants etc.).
1) The SNMP ifInError / ifOutError seems to give an overall counter of all errors from the time the device has started - Am I correct about this?
2) Is there any way I can get the interface-specific errors noted above via SNMP?
Thanks,
Mario

Depends on the device and version of code, but most likely you will get what you want from the CISCO-IF-EXTENSION-MIB. Look at objects like cieIfInRuntsErrs, cieIfInGiantsErrs, and cieIfInFramingErrs. You will also get some ethernet-specific errors from the ETHERLIKE-MIB.

How do I get the Username of an AnyConnect VPN session via SNMP?

I would like to monitor the usernames of my AnyConnect sessions via SNMP. This will allow me to monitor, graph, report, and alert using Solarwinds Orion (or any other SNMP software).
I would like to monitor this on my ASA 5520. I have run the show snmp-server oidlist command and I can see all of the OID's that I can poll. However, the OID I would like to poll crasUsername (1.3.6.1.4.1.9.9.392.1.3.21.1.1) is not working.
Does anyone know how I can monitor the username of a AnyConnect session via SNMP?
Below is a link to a great MIB reference for ASA Remote Access Monitor OID list.
http://www.mibdepot.com/cgi-bin/getmib3.cgi?i=1&n=CISCO-REMOTE-ACCESS-MONITOR-MIB&r=cisco&f=CISCO-REMOTE-ACCESS-MONITOR-MIB.my&v=v2&t=tree

Hello PDX,
Welcome to the HP Support Forums!
To get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at Commercial Forums.
Regards,
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

How to check current input/output rate on router subintenterface via SNMP?

How to check current input/output rate on router (2821, etc..) subintenterface via SNMP, like cacti monitoring system.
I cant find OID to make this with snmpwalk.
Or there is no way to check current load by this way? Only polling?
P.S. Ethernet subinterface, of course.
With great respect, S.A.

Hi,
Try to use:
1.3.6.1.4.1.9.2.2.1.1.6 - InBitRate
1.3.6.1.4.1.9.2.2.1.1.8 - OutBitRate
1.3.6.1.4.1.9.2.2.1.1.28 - ifDescription

Monitor pki certificate status via snmp

I recently discovered that a number of our remote sites could not connect to each other via dmvpn due to various certificate problems.
They could all connect to our hubs due to pre shared keys, so the problem was never discovered before a colleague discovered MM_KEY_EXCH states on some of the routers.
I therefore want to monitor the state of the certificates, preferably via snmp.
I found a nice looking mib,CISCO-PKI-PARTICIPATION-MIB, on http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?local=en&translate=Translate&objectInput=1.3.6.1.4.1.9.9.505
but none of our routers seem to support it, and when you click on "view supporting images", it also specifies: "There is no supporting images available for
CISCO-PKI-PARTICIPATION-MIB"
Do you have any experience on how to monitor certificate status on your Cisco routers?

No real solution. I found that they all needed to connect to one specific router, so I fire off "show crypto isakmp sa | inc MM_KEY_EXCH" on that specific router via our management platform, and receive a mail with the output on a daily basis.

SNMP OID for AssociatedAPs in Virtual WLC 7.4.100.0

Hello Guys!
I need you help for something that I need to do to monitor my Wi-FI network.
I'm using a Virtual WLC (SW Ver 7.4.100.0) where most that 30 APs are associated with, but I would like to monitor each disaciossiation of APs using SNMP. After some search, I have found this OID .1.3.6.1.4.1.14179.2.1.1.1.38 on some forums but it doesn't work, I see random number in my monitoring tool.
Do you know if there is any another OID to use with this software version or maybe if I have to upgrade to ver7.6 or ver8?
Thanks in advance,
Kevin

I'm assuming you don't own a license for Cisco Prime Infrastructure
One thing you can do is send SNMP traps to your monitoring software from the WLC (I've never used virtual WLC but my assumption is most options are the same. If your software doesn't support SNMP Traps consider a different monitoring software...
Go to Management > SNMP > Trap Receivers and set up your receiver
Then to to Management > SNMP > Trap ControlsHere is where you set what traps are sent via SNMP. If you see the "AP" tab you can set several things.
If you only want to see if an AP is dropping off the network and the above doesn't work, you could just put dhcp reservations on your APs and have your software ping it. This of course is only if its off network, not if it simply disassociates.

Port counters via snmp on WRVS4400N

Hi.
I'm using SNMP to read the packet and byte counters on each port on my WRVS4400N. However, I just can't figure out what interface is what port. Also, can I see the total traffic on all ports together as well as the wireless traffic via snmp, which I can see in the web admin interface?
An snmpwalk gives me the following interfaces:
IF-MIB::ifDescr.1 lo
IF-MIB::ifDescr.2 eth0
IF-MIB::ifDescr.3 eth1
IF-MIB::ifDescr.4 eth2
IF-MIB::ifDescr.5 teql0
IF-MIB::ifDescr.6 sit0
IF-MIB::ifDescr.7 tunl0
IF-MIB::ifDescr.8 gre0
IF-MIB::ifDescr.9 ipsec0
IF-MIB::ifDescr.10 ipsec1
IF-MIB::ifDescr.11 ipsec2
IF-MIB::ifDescr.12 ipsec3
IF-MIB::ifDescr.13 br0
I have equipment connected to LAN port 1, 2 and 4 as well as wifi clients. And on the WAN port of course. This is what I get in terms of traffic via snmp (only listing ifInOctets here)
IF-MIB::ifInOctets.1 13454252
IF-MIB::ifInOctets.2 1112133396
IF-MIB::ifInOctets.3 1436498580
IF-MIB::ifInOctets.4 11981231
IF-MIB::ifInOctets.5 0
IF-MIB::ifInOctets.6 0
IF-MIB::ifInOctets.7 0
IF-MIB::ifInOctets.8 0
IF-MIB::ifInOctets.9 0
IF-MIB::ifInOctets.10 0
IF-MIB::ifInOctets.11 0
IF-MIB::ifInOctets.12 0
IF-MIB::ifInOctets.13 1080353959
Any ideas here is appreciated. Thanks.
/Thomas

The RFC1213 Management Information Base for Network Management of TCP/IP-based internets: MIB-II describe the ifDescr value as:
ifDescr OBJECT-TYPE
              SYNTAX DisplayString (SIZE (0..255))
              ACCESS read-only
              STATUS mandatory
              DESCRIPTION
                      "A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface."
There is no standard values for the interface description and you will have to guess from the given name and device caractheristic.
You can also check the OID .1.3.6.1.2.1.2.2.1.3 ifType that can give you a better idea about what it is.
From what you sent we can guess that:
eth0-2 are three Ethernet Interface. But where is the 4th Ethernet interface? Probably it has another name
telq0 should be a load balancing or agregating virtual interface, I guess used for the QoS supported by the router
ipsec0-3 maybe the virtual interface for the ipsec traffic
tunl0 probably the VPN virtual interface
For the reste... you will have to dig a little
I hope this help
Minds are like parachutes, they only function when they are open

MIBS to Monitor Etherchannel and trunks via SNMP

I would like to monitor the status of etherchannel and trunk configurations in 6500 Catalyst switches running both CATOS and IOS. I would like to understand the specific mibs/OIDS that should be monitored for etherchannels and trunks. I am trying to get a better handle on tracking the etherchannels and trunk dynamically and then understanding when the ports are having issues (up/down and errors). I need to understand how to differentiate these type of ports from regular access ports.
Thanks,
Tim

Hi Tim,
what exactly do you want to query via SNMP?
For an (PAgP) Etherchannel, the member-interfaces might be interesting:
https://supportforums.cisco.com/message/3957914#3957914
For a trunk, you could start with the operational mode, depending on the platform you can use:
vlanTrunkPortDynamicStatus (CISCO-VTP-MIB):
vlanTrunkPortDynamicStatus.49 = notTrunking
vlanTrunkPortDynamicStatus.50 = trunking
vlanPortIslOperStatus (CISCO-STACK-MIB):
vlanPortIslOperStatus.13.43 = notTrunking
vlanPortIslOperStatus.13.44 = trunking
Hope that helps
Rolf

How to discover SysIterTrID from BAM's schema

Hi,
I want to populate a BAM's table manually, but i need to provide three additional values, beyond that i can see in Architect, in the fields SysIterID, SysIterTrID and SysIterTotalsChild, present in every BAM' schema table.
I realized that the field SysIterID is an auto increment (starting in zero for each table) and SysIterTotalsChild is always zero. But as the SysIterTrID, it seems a global crosstable counter.
Anybody knows where can I get next SysIterTrID? I thought it was the field "value" in the table "SysIterSequence", but the SysIterTrID created after insert a record in a BAM's table on Architect has a different number.
Thanks a lot.
Luciano

Hey folks,
Is there some specialist that can help me with this problem?
I need to copy rows from one table to another, via table trigger, to consolidate information sent by BPM prrocesss through Process Analytics, but I need to know how to discover the next SyIterTrID I must use.
So, can you tell me where I find the next (or last) SysI'terTrID to use (used)?
Thanks.
Luciano

Shutdown wireless interface via SNMP Write?

Hi
We're working on writing a very simple web app to control a couple of access points via SNMP. I'm trying to shutdown the Wireless interface via SNMP WRITE with the following oid;
.1.3.6.1.2.1.2.2.1.7.1
and
.1.3.6.1.2.1.2.2.1.7.2
But its saying the integer of '0' is invalid (badValue, wrong type or length). I'm able to set other values like hostname, etc, so I know my string is correct...can anyone help? THanks
Jason

Hi
Just found my own answer...the value to shutdown the interface is not 0, it's 2. durrr
Thanks
J

Show conn info via snmp

Hi,
Does the ASA have an SNMP OID which will provide information like the show conn command ?

2 years later, how's LLDP support via SNMP?
If Cisco does not support LLDP via SNMP, please remove the wrong information from
http://tools.cisco.com/ITDIT/MIBS/MainServlet?ReleaseSel=2514&PlatformSel=231&fsSel=705
Stop lying!

LLDP info via SNMP

I'm aware of the show cdp and show lldp CLI commands, but I want to pull the same information out of the devices using SNMP Gets, but cannot seem to find any information relating to that.
Thanks in advance.
Walt

2 years later, how's LLDP support via SNMP?
If Cisco does not support LLDP via SNMP, please remove the wrong information from
http://tools.cisco.com/ITDIT/MIBS/MainServlet?ReleaseSel=2514&PlatformSel=231&fsSel=705
Stop lying!

N5K - monitor vPC status via SNMP

Can I monitor a vPC via SNMP?
I'm interested in "Peer status", "vPC keep-alive status", "Configuration consistency status" and "vPC role".
N5K1(config-if)# show vpc
Legend:
(*) - local vPC is down, forwarding via vPC peer-link
vPC domain id                   : 1
Peer status                     : peer adjacency formed ok
vPC keep-alive status           : peer is alive
Configuration consistency status: success
vPC role                        : primary

Good question, I also want to know how we can do that.
Sent from Cisco Technical Support iPad App

How to discover lwapp hostname via snmp virtual WLC

Similar Messages

Maybe you are looking for