How to do "Test Connection " in WorkFlow

Hi All,
Can any one please tell, how to perform Test Connection to a particular resource in workflow? I am looking for a particular method which performs only connection.
Thanks in Advance.
regards,
RaviG

PFAC
type in rule
click description tab
change language
maintain.

Similar Messages

How can i test my vpn connection?

so recently i decided to test if ver 1.3.0.3 of the quickvpn client would work better with the 1.3.0.5 rvs4000 firmware. i loaded quickvpn to an xp pro computer (freshly built, i might add) and got to work. in order to test the connection, i attempted to piggy back off an unsecured wireless network. this network is on the same ISP network as i am.
i use dynamic DNS, and the unsecured wireless network could resolve my IP correctly, but for some reason i couldnt connect to my home network from the unsecured network. my router is set to respond to lan requests, but i couldnt ping it. my router passes HTTP traffic to a computer in my network, but i couldnt bring up the webpage. finally, my router responds with the router config page over port 443, and i couldnt bring that up.
so i used my ISP's dialup service to test. initially, as always, i had a million problems with the vpn client. systematically, i tried to resolve the issues. i installed the patch in the readme for quickvpn. i checked log files to see where stuff was failing. eventually, i could connect to the VPN, but would get that "remote gateway is not responding" crap. i know of a (poor) workaround for this which allows you to "finalize" the connection, but that workaround doesnt allow you to ping around in your network. sometime later, after randomly messing with settings, the tunnel would connect without the workaround. i have no idea what "fixed" this.
despite all this, my 28.8Kbps connection wouldnt allow me to do anything meaningful on my network. i couldnt connect to the router or to a server of mine (http or fileshare). the only thing i could do was ping internal devices. other requests seemed to "hang" rather than timeout or do anything more concrete. basically, i gave up on testing using dialup, even though my router and the client software confirm a good connection. but i still wasnt convinced.
next, i figured i could create some type of "DMZ" on my network by placing a switch between my ISP's modem and my router. im not a cisco network professional by any means, but im pretty familiar with networking on a above-average level. that said, despite my best, i couldnt get my quickvpn computer to see my router from the "DMZ".
finally, i figured i could just test the tunnel while directly connected to my network's lan. bad idea. everything seems to go okay until it locks up on "activating policy". rebooting or otherwise ending the negotiation ends in the computer being unable to do anything anymore. when i try to ping anything, i get "negotiating ip security" ad infinitum. the only way i could fix this was by doing a system restore.
so here's the question: how can i test my quickvpn connection?why can't i just tunnel through my network? and before you scream that you can't, thegreenbow vpn client has NO PROBLEM connecting to my rvs4000 while connected to my own network.

Hi Aaron,
I am going exactly the same thing as you however, I had my cousin buy and install a RVS4000 at his house in Australia.
I access it from the USA so that I can help manage his Local Area Network, he is just not technical..
I setup a DDNS client on his RVS4000 so that I can always get to his Router via a domain name rather than a IP address.
I noticed that you didn't mention anything regarding importing client certificate into the directory of the VPN client on your PC.
I also noticed I disabled IPSec passthrough on the router in Australia, see the pictures below, not sure why, but the VPN client is working.
I also did not setup any gateway to gateway VPN tunnels, Only added a client , exported certificate as per the manual, See the last screen capture below.
You will also note if you view the screen captures that my cousins RVS4000 has not been upgraded to the new code.Is there a reason for that...not really...he's just a user, not really technical. Also note I have not added any VPN tunnels on my RVS4000.
I have a reasonably reliable connection between the USA and Australia. I didn;t have to play with any other options, just add users to the VPN client database.
Your description of the working environment of your PC is missing details on the version of XP, so i will mention the following taken from the software release notes of the RVS4000 ;
There is a known issue with Windows XP SP2 Firewall.
ICMP packets are always dropped by the firewall when the firewall is enabled.
This issue causes the QuickVPN client to be unable to establish a tunnel with the remote QuickVPN server successfully.
Microsoft has released a patch to fix this issue, which you can get from:
http://support.microsoft.com/kb/889527/en-us
After you install the patch, the issue should be resolved. You can also fix this issue by upgrading Windows XP to SP3.
You cannot plug a PC on the same network as the router for testing, they must be on dissimilar WAN networks for testing purposes.
Your remote PC VPN client will not be allocated a IP address in the RVS4000's network, hosts behind the RVS4000 will still respond to pings, as they direct the responses to their default gateway, the RVS4000.
The thegreenbow VPN client is a distracter at this point costing 50 something EURO for a license, lets try to get the quickVPN client working !
So, if you still wish try the following, firstly make sure your XP has been upgraded to SP3;
1. If you upgraded your router to the new version of code, then reset your router to factory defaults to re-initialize your router, yes start again.
2. Export the VPN client certificate to the directory that contains the VPN client. In my case it is;
"C:\Program Files\Cisco Small Business\QuickVPN Client"
3. add a VPN client account to the router
4. Use port 60443 from the quickVPN client. and try VPNing to the router.
5 hmmm, if the client still fails try disabling IPSec Passthrough on the router for grins and giggles.
If this fails, call the SBSC at the following location for resolution;
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
good luck ...regards Dave

How do You Test EMail Connectivity?

How do You Test EMail Connectivity?
Once you setup the mail gateway with an IP address, port, and domain name. How can you test email connectivity? How do you force the MARS Appliance to send an email?

There is no "test e-mail connectivity" button/function. Essentially you need to configure inspection rules to notify you when they are fired by mars.
You will need to setup a user (preferably a non-admin account for testing) under "Management"-"user management"(if you haven't already done so) make sure to supply e-mail address.
http://www.cisco.com/en/US/docs/security/security_management/cs-mars/6.0/initial/configuration/setup.html#wp1030836
Now you can "Configure a Rule to Send an Alert Action." the following link explains how to do this...An easy one would be the "System Rule: CS-MARS Login Failures - Non-Admin User" rule. Follow the instructions in the link below under the "Configure a Rule to Send an Alert Action" section to modify the rule mentioned above. Keep in mind that this rule only fires when there are login failures. Once you have modified this rule try logging into mars using the non-admin user with a bad password...you should get a e-mail from MARS.
http://www.cisco.com/en/US/docs/security/security_management/cs-mars/6.0/user/guide/combo/alerts.html#wp1056101
Hope this helps.
Dustin Suko

Question in ACS radius ports and how test connectivity between router

hi all
im asking here about default ports used in cisco acs for radius protocol
is it 1812 and 1813 ???
or there is another ports ??
Q2-
how to test connectivity between ACS "server aaa" and the router "client aaa " ??????
Q3-
can anyone give me simple config on router for radius protocol to connect acs based on radius protocol ?
regards

The default authentictaion port is 1812 and the default accounting port is 1813.
Here's an example config-
aaa new-model
aaa group server radius ACME-RADIUS
server-private 192.168.1.5 auth-port 1812 acct-port 1813 key SeCrEtPaSsWoRd
aaa authentication login default local
aaa authentication login ACME-AAA group ACME-RADIUS local
aaa accounting send stop-record authentication failure
aaa accounting exec default start-stop group ACME-RADIUS
line vty 0 4
login authentication ACME-AAA
You can test with-
test aaa group radius server 192.168.1.5 mmessier St@nleyCup
where mmessier is your username and the password is St@nleyCup

How can I test my thunderbolt port? It's not working after the update to 10.10.1

I have been using my computer with the Thunderbolt Port for a while and after updating to 10.10.1 and after I while of using my computer I tried to use the thunderbolt port with my external monitor.. and it doesn't work at all.. video doesn't come out.. I tried a different screen with the mini adapter from thunderbolt to HDMI and another with thunderbolt to VGA and in both adapters I don't get video from my mac.
Any idea how can I test my Thunder bolt port?
This is what I have done:
1 cable adapter thunder bolt to mini HDMI to an LCD screen with HDMI : No video, but my computer detects that there is something connected
2 cable adapter thunder bolt to VGA to an LCD screen with VGA : No video, but my computer detects that there is something connected
3 cable adapter thunder bolt to mini HDMI to an 40' TV with HDMI : No video, but my computer detects that there is something connected
All the test pass from the Hardware test at the startup (press D at boot time).
Any ideas? my guarantee it's expired and no coverage. Due the nature of where the port it's installed, if this is a hardware problem seems that I will (may be) have to buy the Logic Board.. no good. No bueno!!
Thanks!!!

restore iPhone

Error while Test Connection with Connector

hi all:
     there is an error while Test Connection with Connector , I also test it through sys administration->sys configuration->
suport -> sap transaction, I got all errors, I put these two errors as folows, could you please tell me how to sovle it
***************ERROR 1 while *error while Test Connection with Connector ******************************************************
Test Details:
The test consists of the following steps:
1. Retrieve the default alias of the system
2. Check the connection to the backend application using the connector defined in this
system object
Results
Retrieval of default alias successful
Connection failed. Make sure that Single Sign-On is configured correctly
************error sys administration->sys configuration-> suport -> sap transaction        ********************** 1.5 #0025B3E02892006100000A0800001798000487530FB0122E#1274690722265#com.sap.portal.prt.runtime#sap.com/irj#com.sap.portal.prt
.runtime#guodongdong#47472##n/a##690347f0670e11df98cc0025b3e02892#SAPEngine_Application_Thread[impl:3]
9##0#0#Error##Java###04:4524/05/10_0077_6087550
[EXCEPTION]
#1#com.sapportals.portal.prt.runtime.PortalRuntimeException: Exception in SAP Application Integrator occured: Application URL
&\#39;:///sap(ZT1KVXBWektldldTeV9QQXBXRjNaWTRBLS1OZmRvZzBRWWY2QmN0WThNUmgqdUlRLS0=)/bc/gui/sap/its/webgui&\#39; is not valid!
Please check the protocol and host entries for system &\#39;sapdev&\#39;.
     at com.sapportals.portal.appintegrator.AbstractIntegratorComponent.doContentPass
(AbstractIntegratorComponent.java:123)
     at com.sapportals.portal.appintegrator.AbstractIntegratorComponent.doContent(AbstractIntegratorComponent.java:98)
     at com.sapportals.portal.prt.component.AbstractPortalComponent.serviceDeprecated(AbstractPortalComponent.java:209)
     at com.sapportals.portal.prt.component.AbstractPortalComponent.service(AbstractPortalComponent.java:114)
     at com.sapportals.portal.prt.core.PortalRequestManager.callPortalComponent(PortalRequestManager.java:328)
     at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:136)
     at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:189)
     at com.sapportals.portal.prt.component.PortalComponentResponse.include(PortalComponentResponse.java:215)
     at com.sapportals.portal.prt.pom.PortalNode.service(PortalNode.java:645)
     at com.sapportals.portal.prt.core.PortalRequestManager.callPortalComponent(PortalRequestManager.java:328)
     at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:136)
     at com.sapportals.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:189)
     at com.sapportals.portal.prt.core.PortalRequestManager.runRequestCycle(PortalRequestManager.java:753)
     at com.sapportals.portal.prt.connection.ServletConnection.handleRequest(ServletConnection.java:240)
     at com.sapportals.portal.prt.dispatcher.Dispatcher$doService.run(Dispatcher.java:523)
     at java.security.AccessController.doPrivileged(Native Method)
     at com.sapportals.portal.prt.dispatcher.Dispatcher.service(Dispatcher.java:412)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
     at com.sap.engine.services.servlets_jsp.server.servlet.InvokerServlet.service(InvokerServlet.java:156)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
     at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:401)
     at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:266)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:386)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:364)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:1039)
     at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:265)
     at com.sap.engine.services.httpserver.server.Client.handle(Client.java:95)
     at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:175)
     at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process
(ApplicationSessionMessageListener.java:33)
     at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
     at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
     at java.security.AccessController.doPrivileged(Native Method)
     at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:104)
     at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:176)

Hi,
As per this part of the trace:
Exception in SAP Application Integrator occured: Application URL &\#39;:///sap(ZT1KVXBWektldldTeV9QQXBXRjNaWTRBLS1OZmRvZzBRWWY2QmN0WThNUmgqdUlRLS0=)/bc/gui/sap/its/webgui&\#39; is not valid! Please check the protocol and host entries for system &\#39;sapdev&\#39;. at ...
You can clearly see that the system object 'sapdev' is not configured correctly/at all - you are trying to launch transaction iView
(WEBGUI) and in order to do so you should configure the 'internet transaction server' category of the system object
with the hostname of the ITS server.
Generally the template is
<System.Access.ITS.protocol>://<System.Access.ITS.hostname>/sap<ESID>/bc/gui/sap/its/webgui?\....
So that's why you got
Please check the protocol and host entries for system ..

How to change the connection for a recurring report

I have a group of reports running in production on recurring schedules. I need to update the database connection for these as we are changing our server environment.
I open the report in Crystal Reports 11 and changed the database connection saved the report back to the Enterprise Server location (I also have a backup of the original). When I preview the report using the Central Management Console, the report uses the updated database connection info. When I test the recurring report I get a logon failure. When I go to the instance to look at the database logon for the recurring instance it shows the old database connection.
How can this database connection get updated for the current group of instances for these recurring reports?
Thanks
BOBJCMC

Hi Stratos,
I tried to use .NET SDK to update the Logon_Info properties as below. But it does not seem to be working. Is this the correct way to update logon info for recurring instances?
infoObject.ProcessingInfo.Properties["SI_LOGON_INFO"].Properties["SI_LOGON1"].Properties["SI_USER"].Value = <userid>
infoObject.ProcessingInfo.Properties["SI_LOGON_INFO"].Properties["SI_LOGON1"].Properties["SI_PASSWORD"].Value = "pwd"
Thanks
Ajith

How old is test/dev environment?

Hi,
How can I check, How old is test/dev environment which was cloned from PROD in past.
by the creation time of control file?
Thanks

Just for the pourpose of sharing knowledge, even if your regular backup strategy does not include rman, you can still issue this command. I have created a just recently cloned database out of the seed, it works too.
[oracle@cursocfe log]$ rman target /
Recovery Manager: Release 10.2.0.1.0 - Production on Tue Apr 24 14:03:49 2007
Copyright (c) 1982, 2005, Oracle. All rights reserved.
connected to target database: DEMO (DBID=3364817245)
RMAN> list incarnation of database;
using target database control file instead of recovery catalog
List of Database Incarnations
DB Key Inc Key DB Name DB ID STATUS Reset SCN Reset Time
1 1 DEMO 3364817245 PARENT 1 30-JUN-05
2 2 DEMO 3364817245 CURRENT 446075 24-APR-07

Test Connection failed in Crystal Reports for Eclipse using SQL Server 2008

I installed an SQL Server Express 2008 on my local PC (Window XP SP3). I downloaded sqljdbc4.jar to Crystal Reports for Eclipse
IDE library path and tried to Test Connection, but got the Ping failed message : The TCP/IP connection to the host localhost, port 1433 has failed. It said that check that an instance of SQL Server is running on the host (I saw SQL Server SQLEXPRESS is Running on my PC) and accepting TCP/IP connection at the port (I enabled TCP/IPin my PC's SQL Server Network Configuration),
and that no firewall is blocking TCP connection to the port(I turned OFF Window Firewall on my OC). Can anyone tell me how can I fix this problem ?

Hi,
Check the below thread also:
http://scn.sap.com/thread/1634856
Thanks,
DJ

Can't Create a Data Source - Failed to test connection. [DBNETLIB][ConnectionOpen (Connect()).]SQL Server does not exist or access denied

Hi there,
I am having a serious issue with The Power BI Data Management Gateway which I am hoping that someone can help me with.
Basically I am setting a connection between a Power BI demo site and a SQL 2012 Database based on Azure. The Data Management Gateway and is up and running, and Power BI has managed to connect to it successfuly.
By following the tutorials at
here I was able to successful create my Data Connection Gateway with a self-signed certificate.
However, when trying to create the data source I come into problems. The Data Source Manager manages to successfully resolve the hostname, as per the screenshot below:
Bear in mind that I exposed the require ports in Azure as endpoints and I managed to modify my hosts file on my local machine so I could access the SQL server hosted in Azure using its internal name -- otherwise I would not be able to get this far.
However the creation of the data source also fails when trying to created it whilst logged in the SQL server in question:
The Data Source Manager returns the error when using the Microsoft OLE DB Provider for SQL Server:
Failed to test connection. [DBNETLIB][ConnectionOpen (Connect()).]SQL Server does not exist or access denied
I tried using the SQL Server Native Client 11.0 instead but I also get an error. This time the error is:
Failed to test connection. Login timeout expiredA network-related or instance-specific error has occurred while establishing a connection to SQL Server. Server is not found or not accessible. Check if instance name is correct and if SQL Server is configured to allow remote connections. For more information see SQL Server Books Online.Named Pipes Provider: Could not open a connection to SQL Server [53].
Some considerations
If I provide an invalid username/password, the Data Source Manager does say that the username and password is incorrect.
Firewall is turned off in the SQL Server (either way, this error also happens if I try top use the Data Source Manager whilst logged in the SQL Server itself).
SQL Profiler does not show any attempt of connection.
The SQL server instance in question is the default one.
The error happens regardless if I select the option to encrypt connection or not.
In SQL Configuration manager I can see that all protocols are enabled (TCP/IP, Named Pipes and Shared Memory.
The Event Viewer does not provide any further errors than the one I have copied in this post.
I'm at a loss here. Could someone please advise what might I be doing wrong?
Regards,
P.

Here is what I had to do to solve this issue:
Basically I had to add the MSSQL TCP/IP port as an end-point in Azure. After I did that, then I was able to create the data-source. However, I was only able to authenticate with a SQL account, as any domain account would return me an error saying that the
domain isn't trusted.
What puzzles me here is how come the Data Source Manager would inform me that an account username/password was invalid, but it would fail/timeout if I provided valid credentials (!?!?!!?)

How can I test my discrete graphics card in an MBP Retina?

How can I test the hardware on the discrete Nvidia grpahics card in my late 2012 MBP Retina?
I've had a *lot* of problems with it which I won't repeat here but the latest fun thing it's doing is crashing and requiring a hard reset any time *anything* attempts to access the discrete graphics card. This includes but is not limited to:
*Opening system profiler and clicking on Graphics (it displays a blank screen)
*Running a 3D graphics benchmark
*Running intensive mathematical calculations on the GPU
*Connecting to an external monitor with the thunderbolt port and using the computer for a short period of
None of these things actually work and after unsuccessfully attempting any of them the computer becomes very unstable shortly there after and usually crashes and requires hard reset. One time I got a crash report that said something about GPU panic.
Any recommendations? I get the sense that the apple hardware test is not doing a thoroough test of the GPU if at all.
Thanks.

If they add OSX support for this product and it comes in at a reasonable price point, it could be an attractive solution.
http://www.anandtech.com/show/5352/msis-gus-ii-external-gpu-via-thunderbolt
Also, there are products from other companies that allow connection to PCIe cards through thunderbolt. These two are geared more towards professional use (Audio/Video I/O cards).
http://www.sonnettech.com/product/echoexpresschassis.html
http://www.magma.com/thunderbolt.asp

How to configure informix connection pool in sun-one appserver 7

Hello,
Anybody knows , How to configure informix connection pool properties in sun-one appserver 7?
Thanks in advance.

Actually,it couldn't get some advice in here.But now,I known how to configure it,I expended 2 days to search and test it.Follow :
jdbc class:com.informix.jdbcx.IfxDataSource
serverName=(INFORMIXSERVER)
portNumber=1526(default)
IfxIFXHOST=(host ip)
databaseName=(your dbname)
user=(your username)
password=(your pwd)
attention:configure right transaction and userthreads in your informix sever
Hope helpful to someone!

How do you test your new laptops?

To the gurus or people who have researched this question: How do you test your new laptops?
When you get a new laptop, what do you do to test it?
My X1Carbon might arrive in a couple weeks, and reading about all the failures and DOAs is scary. So assuming mine is not simply DOA, how do you shake out the less obvious or more obscure problems?
I did search for this info before posting. One other person asked the question,
>> Would appreciate advice re optimal set-up and what testing/diagnostics to do to determine if ther...
but no one answered.

With testing I start with the basics and work my way to the harder stuff.
Inspect the external condition of the machine.
Boot and enter the BIOS before Windows. Review settings then power off.
Boot from Acronis True Image Home backup/recovery DVD and clone HDD or SSD and thus the factory image before it's ever booted to Windows.
Boot to Windows and look carefully at the Lenovo factory image and try to get an understanding for the Lenovo software and why it is there. This does not include the other software from Microsoft, Google, etc.
Create Lenovo Factory Image DVD set with Rescue and Recovery. Throw disk set in the box or put on the shelf in case the machine is ever re-sold.
Test all of the ports - I test every port on the machine for my expected usage. For instance, in the case of the X1 Carbon I would confirm the mini DisplayPort connection works correctly with an external LCD panel. If the machine had a IEEE firewire port or something, test that. Test the USB 3.0 ports with a known working external external enclosure and verify transfer speeds.
Test the SSD speed with CrystalDiskMark, ATTO and AS Disk Benchmark software to get a good overview of the performance.
Install HWiNFO and look carefully at the components. Observe turbo boosting, thermals and fan RPM over the course of a few days for battery and AC power.
Do at least one full battery discharge and recharge. Observe the cycle and details are being properly displayed and recorded in Lenovo Power Manager.
Download all software and drivers from support.lenovo.com for the model being tested. Confirm visually you have all the core components needed. Core includes the drivers, power management driver, Power Manager, hotkeys, etc.
Flatten the machine and install Windows or Linux from scratch. Install drivers and software.
Re-test ports and confirm the machine is working properly.
Benchmark the SSD again. Confirm no change.
Install HWiNFO and confirm turbo, thermals and fan speeds are still proper.
Install core applications and test them. There may be core features in Windows that also need to be installed and tested. For instance, Windows 8 Hyper-V for virtualization.
Connect any external devices you expect to use and test them. For instance, video cameras, smartphones, mp3 players, digital cameras, printers, USB docks, etc.
Do several battery tests with your typical applications and behavior. The goal here is to simulate how the machine will be used in your day-to-day setting or travel scenarios. I usually do at least three tests. This can be rather time consuming with long battery life machines so I get a lot of other testing out of the way first.
By the time you get to this point, if you haven't hit any major roadblocks you'll start to have a good feel for the machine, and if it is going to be a keeper or not. The assumption here is that during this timeframe you have been observing the screen, keyboard, and trackpad performance to see if it's to your liking. The other assumption is that you are using the machine and applications in the scenarios you are purchasing it for.
I don't run synthetic benchmarks. I prefer to test a machine against the scenarios I expect to use it with. I spend most of the first week making this assessment. If any major hardware defects are present, the machine is automatically returned. I do not repair machines just received. No exceptions.
Week 2 is for ironing out any minor issues and assessing if the machine meets the requirements for the scenarios it will support. If it does, it is kept. If it does not, it is returned. This week includes subjective and objective input. You have to weigh the pros and cons for a machine against your priorities. It is rare that a machine is perfect so you have to decide the ROI for the machine. Service and Support must be considered so week two might include a call to support for any unresolved issues. Don't discount the service you receive during this period.
After week two, you are likely right on top of the last day to return a Lenovo machine. The return period is 21 days from the invoice date (I believe), not the day the machine is received so make sure you are well aware of it. After 21 days, the machine is yours for good unless you sell it. Decision time.
Good luck.

RFC error with SAPOSS (test connection)

Hello All,
RFC error with SAPOSS Test connection
Language:EN
Client      :001
User        :OSS_RFC
Target system settings:
Balace load = Yes
RFC error is below:
                          Connection test SAPOSS
Connection type:    R/3 connection
Connection error        Error opening an RFC connection.
ERROR                  partner not reached (host 209.94.207.139, service sapdp99)
LOCATION              SAP-Server orionbw_QBW_00 on host orionbw2 (wp 0)
DETAIL                   NiPConnect
CALL                      connect
COMPONENT         NI (network interface)
COUNTER               9
ERROR TEXT           Network is unreachable
ERROR NUMBER    101
MODULE                 nixxi.cpp
LINE                        8628
RETURN CODE       -10
SUBRC                   0
RELEASE               640
TIME                      Wed Jul 30 10:06:05 2008
VERSION               37
Please let me know how to proceed.
Thanks in advance.
Best Regards,
Pratyusha

Hi Markus,
I went to OSS1 transaction Menu ---> Parameter --> Settings -
> SAP Routers at Customer Site ---> SAP Router 1
i have Added Name and IP address and instance No.
Now its throwing another error:
=============================================
ERROR                   rgcwebsrv: route permission denied (orionbw2.rgc.corp to 147.204.2.5,
LOCATION                SAProuter 37.11 on rgcwebsrv
COMPONENT            NI (network interface)
COUNTER                 5580
MODULE
LINE
RETURN CODE          -94
SUBRC                       0
RELEASE                   640
TIME                           Wed Jul 30 10:41:28 2008
VERSION                     37
=============================================
We are struck here.
Thanks in advance
Best Regards,
Pratyusha

How can to get connection at runtime?

I use Jdev 11.1.1.4 adf JSF.
I have 2 connection into Model.jpx.
First I use in production and second I use in test.
I would like to change the value of the variable name nowDate, in "Bean Variables" in Query into "View Object".
Specifically, I'd like to change the value of nowDate either adf.currentDate, when I have choose first connection or *12/01/2010* when I have choose second connection.
It's possible?
I don't know how retrive the database connection used to create business components from existing database object by code and i don't know how to write the code in "Expression Editor" into "Bind Variable" of "View Object".
Thank's a lot for any help.

hi user2964099
... because I have not records with current Date into my local Database ...Maybe it is worth considering to get your data into the shape you need it (using SQL scripts), instead of making your application more complicated (possibly introducing bugs) just for this.
... and I do not know how to write the code in "Expression Editor" into "Bind Variable" of "View Object" for this ...In forum thread "ADF BC : how to use bind variable (default) values in UI "
at ADF BC : how to use bind variable (default) values in UI
I refer to the example application BindVarDefaultsInUIApp-v0.01.zip and I write about it ...
Jan Vervecken wrote:
note : In the example application the Bind Variables have as default value a Groovy expression like "adf.object.viewObject.fromHireDateBVarDefault".... maybe that can help.
success
Jan Vervecken

How to do "Test Connection " in WorkFlow

Similar Messages

Maybe you are looking for