How to enable or disable report parameter based on certain conditions
Hello ALl,
I have 3 parameters in my report. Fst parameter is having a LOV which is having all status value like 'Received,Refunded, Exempted etc).
second parameter is From date and third parameter is To Date which is having value set as "FND_STANDARD_DATE'
Now my requirement is If Status is selected as "Exempted" then From and To Date should be disabled.
if other than that then both should be enabled.....
Please help me out.
How it cna be done.
Thanks in advance
sheetal
Hi,
You can use a condition
<?xdoxslt:ifelse(Condition,'Paragraph','')?>
Condition is the condition that needs to be satisfied
Paragraph is the paragraph that needs to be displayed if the condition is satisfied
'' is what needs to get displayed if the condition is not satisfied.
Thanks,
Swarna
Similar Messages
-
How to enable my disabled I pad
How to enable my disabled iPad
If you cannot remember the passcode, you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and resync the data from the device (or restore from a backup).
If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present.
You may have to force iPad/iPod into Recovery Mode
http://support.apple.com/kb/ht4097 -
How to Override Cost Center in IT 1 based on certain conditions
Hi,
I have a pretty good understanding on how Cost Center gets defaulted based on Org Structure. The standard SAP solution for Cost Center will not work for my client and I need to determine the cost center based on certain conditions. I understand that I have to write custom code in some user exit or badi. I tried user exit EXIT_SAPFP50M_001, but it did not work.
Here is my code:
DATA: I0001 LIKE P0001.
CASE INNNN-INFTY.
WHEN '0001'.
CALL METHOD CL_HR_PNNNN_TYPE_CAST=>PRELP_TO_PNNNN
EXPORTING
PRELP = INNNN
IMPORTING
PNNNN = I0001.
This is just an example to test the concept
I0001-kostl = 'COST_CENTER'.
CALL METHOD cl_hr_pnnnn_type_cast=>pnnnn_to_prelp
EXPORTING
pnnnn = i0001
IMPORTING
prelp = innnn.
endcase.
When I change IT 1 record and hit enter, I can see that my code is being executed. I can see cost center being updated on the screen, but when I save it, its not able to retain that new cost center value. This might be because cost center is not an open field.
How can I change my code so it retains its value after saving?.
Thanks!Contd to manoj
Cost Center will be a Open feild when the value of the switch PLOGI ORGA should be balnk if it is haveing 1 than it will not default the value kindly check -
VT02N - do PGI and Invoice for certain deliveries either based on certain conditions
Hi Friends ,
We are using VT04 for creating shipments . While shipment completion stage in VT02N an activity profile has been maintained which does both the Goods issue and Invoice.
We have a business requirement , PGI and Invoice should be created only for specific set of deliveries based on certain conditions.
Is there any standard way to do this or by using user exits.
Please guide.
Thanks,
Nileshsa.what about adding a check in userexit RV60AFZZ, when the condition is not met during invoice creation, error out and disable the creation of the invoice document?
-
How to enable or disable buttons on an interactive ALV report
I have two buttons on Interactive ALV report. Before displaying the ALV report, I want to enable or disable buttons on ALV depending on some conditions.I dont want to make the buttons visible or invisible. This is not an OO ALV report.
Please suggest !!!Then you have to use the event set_pf_status or parameter I_CALLBACK_PF_STATUS_SET for this pass the form name.
You have to Implement the form Routine.
FORM PF_STATUS using status type SLIS_T_EXTAB.
SET PF-STATUS 'STS' excluding status.
ENDFORM.
First create the pf-staus using SE41 or double click on the status name and create . By default you make them Disable mode. -
How do I create a dynamic parameter based on a formula?
Hi,
I've developed a report, in CR 11, that is parameterized based on the field "ticket_date". I've created a Min and a Max formula so that I can select a date range. This works wonderfully. However, my date list is growing longer by the day and each day I have to run the report I need to scroll through an even longer list of date values. This will become increasingly impractical with each passing month and year. I would like create a "Year" paramater and a "Month" parameter so that I can first select the Year, then the month(s), then the dates.
When I attempted to create a parameter based on the formula, "Year (), the formula wasn't in the list of available values to create a parameter on.
How can I address this requirement?
thanks in advance!
MarkHi Abhilash,
Looks like I was able to create a Year field in the Command - thanks for the tip!
Before I close this off as answered can you take a look at two sets of SQL I wrote in the Command that I'm getting errors on and offer advice on where the error is occurring.
Example 1
The SQL I attempted to write must be close though:
Select ft.sequence, ft.ticket_date, coff.office_name, comp.subscriptions_id from
field_tickets as ft, company_offices as coff, companies as comp
INNER JOIN jobs ON comp.companies_id=jobs.companies_id
INNER JOIN field_tickets ON jobs.jobs_id=field_tickets.jobs_id
LEFT JOIN company_offices ON jobs.company_offices_id=company_offices.company_offices_id
Where comp.subscriptions_id=7.00
When I attempt to save this I get an error:
"Failed to retrieve data from the database. Details: Exception: Error Message: Java Heap Space"
Example 2
I get the error, "Not unique table/alias: 'custom_jobs_values'" for the following SQL Command
SELECT companies., jobs., field_tickets., regions., customers., custom_jobs_values. FROM
companies, jobs, field_tickets, regions, customers, custom_jobs_values
LEFT JOIN custom_jobs_values ON jobs.jobs_id=custom_jobs_values.jobs_id
INNER JOIN regions ON companies.regions_id=regions.regions_id
INNER JOIN jobs ON companies.companies_id=jobs.companies_id
INNER JOIN field_tickets ON jobs.jobs_id=field_tickets.jobs_id
INNER JOIN customers ON jobs.customers_id=customers.customers_id and
companies.subscriptions_id=4.00
thanks!
Mark -
Enabeling/Disabling Report parameter
Hi,
I have to enable/disable the report parameter values depending on the other parameter.
For Eg. I have three report parameters
1. Range- Value set: Yes_No
2. From Date- Value Set:FND_STANDARD_DATE
3. TO date- Value Set:FND_STANDARD_DATE
I have to disable 'From Date' and 'To date' values if Range parameter value is 'No'
We can't modify FND_STANDARD_DATE parameter and can't use $FLEX$.YES_NO to enable/disable values. Can we do this using special value set? I'm ok with creating new custom value sets for 'From Date' and 'To Date' but final date format must be Standard Date
Regards,
RavindraHi,
To achieve this functionality, I have used the special value set.
I'm able to enable/disable the date parameters. However I'm getting following error while entering the date in the date fields.
app-fnd-00006: User Exit #FND PLSQL is not defined
Details:
1. Range- Value set: Yes_No
2. RANGE_DUMMY Value set:None
This will returen Y/N depending on range parameter value.
3. From Date- Value Set:CUSTOM_FND_STANDARD_DATE, Type:Special
This is the special value set. I've added the following quey in the VALIDATE section of the value set
FND PLSQL"BEGIN
IF :$FLEX$. RANGE_DUMMY= N THEN
NULL;
END IF;
END;
4. TO date- Value Set:CUSTOM_FND_STANDARD_DATE,Type:Special
Fromat Type:Standard Date
I'm able to enable/disable the date parameters using above function but its giving mentioned error while entering value for From Date parameter
Regards,
Ravindra
Edited by: user12228525 on Jan 23, 2013 4:01 PM
Edited by: user12228525 on Jan 23, 2013 4:08 PM
Edited by: user12228525 on Jan 23, 2013 4:09 PM
Edited by: user12228525 on Jan 23, 2013 4:11 PM
Edited by: user12228525 on Jan 23, 2013 4:12 PM -
How to enable execute-disable bit and other hidden settings on Lenovo 3000 N200 model 0769!
2008-11-16: I have posted some more settings, scroll down to message 19 in this thread to read them.
Hi,
Here's some good news for anyone with a Lenovo 3000 N200 model 0769, who is disappointed and frustrated with the lack of options in the BIOS setup menu. (I had a moan about that in this thread.)
This is a long post but I hope you'll find it worthwhile. Here are the features/settings which I will explain how to enable:
The BIOS disables the execute-disable bit function of the CPU, with no way to turn it on. You can enable it.
You can set VGA and VESA graphics modes to not be stretched to fill the whole screen (sharper graphics with no distorted aspect ratio).
Speed up the POST display by skipping the memory test
Disable various features (if you don't use them, that might save some power): the HD audio controller, WLAN card, on-board LAN, shadowing of the video BIOS
Enable beep before booting the OS
Enable key click sound (only in DOS, not Windows or Linux)
I'm still working on this, and hope to figure out more hidden settings soon, e.g. to disable the DVD drive and trackpad, and to change the video output from NTSC to PAL.
The information below applies to the Lenovo 3000 N200 model 0769 with BIOS version 3.03. My N200 has Nvidia graphics. For some background on the general principles/research required to figure this out, please see this thread at Wimsbios.com.
To change the settings, you need to create a bootable DOS floppy disk or USB drive. Download SYMCMOS.EXE (Google for it) and put it on the bootable disk. Boot the disk and run SYMCMOS to back up your current CMOS settings: SYMCMOS -Lsettings.txt
Next load the settings.txt into a text editor. It will begin like this:
( SYMBOLIC CMOS EDITOR - Version 643710-035 )
CRC = 3EDD
(0000) [0001]
(0003) [0001]
Your CRC value may differ. Each line after the CRC contains a token number, followed by the value of that token. You can start with the settings.txt you created and edit any tokens you want to change, or delete all token lines and just include the tokens you want to change. Then use SYMCMOS.EXE to apply the new file: SYMCMOS -V2 -Uupdate.txt
After running that command you can reset, and hopefully notice the new settings in action. (For certain settings, such as re-enabling the execute-disable bit, you need to turn the computer off then on again.)
Here are some specific tokens you can change:
Token Default New Description
(0000) [0001] [0000] Disable the HD audio controller
(0042) [0001] [0000] Disable LCD panel graphics scaling/stretching
(004B) [0000] [0001] Beep before booting the OS
(0267) [0001] [0000] Enable support for the CPU execute-disable bit
(028E) [0000] [0001] Enable key click (only works in DOS and BIOS setup)
(02A3) [0001] Set to 0 for slower memory test, or 2 (or 3?) to skip
test for faster booting, especially with 4GB RAM
(046E) [0001] [0000] Disable video BIOS shadowing. (Best to leave enabled.)
(0471) [0000] [0001] Enable 1MB memory hole at 15MB. (Best leave disabled.)
(0486) [0001] [0000] Disable PCI Express ports 1-6. This takes precedence
over the individual port bits below, and disables the
LAN, WLAN and (probably) ExpressCard port.
(0489) [0001] [0000] Disable PCI Express port 2 (WLAN card)
(048C) [0001] [0000] Disable PCI Express port 3 (maybe ExpressCard?)
(048F) [0001] [0000] Disable PCI Express port 4 (LAN)
For example, if you want to disable LCD panel scaling and enable the execute-disable bit, you would create a text file like this:
CRC = 3EDD
(0042) [0000]
(0267) [0001]
Some final points:
Loading the default settings in the BIOS setup menu will overwrite any changes you make using SYMCMOS.EXE. So keep that bootable disk around in case you need to re-apply your settings in future.
The token numbers above are specific to version 3.03 of the Lenovo 3000 N200 model 0769 BIOS. They might be different for earlier BIOS versions, and will be different for other models of computer.
Once you have created a bootable floppy disk with a text file containing your updated settings, you could create a bootable CD with the floppy's data on. Just boot that CD to restore your settings in future.
Before experimenting with randomly changing token values to discover other hidden settings, make sure you know how to reset your computer's CMOS memory! Changing some settings results in your computer becoming unable to boot, so you can't use the BIOS setup screen to reset. I wrote about how to reset the N200 model 0769 CMOS in this thread.
If you discover any other settings, please let me know.
Any changes made are at your own risk; if you "brick" your laptop don't blame me!
Message Edited by Donuts on 10-15-2008 09:45 AM
Message Edited by Donuts on 11-16-2008 11:35 PMHi Donuts !
My computer is a 3000 N200 0769BAG. It has a Dual Core Pentium and the information I get about the BIOS using lshw are :
========================================================================================
description: BIOS
vendor: LENOVO
physical id: 0
version: 68ET35WW (04/16/2008)
size: 106KiB
capacity: 960KiB
capabilities: pci pnp apm upgrade shadowing escd cdboot bootselect edd int13floppy360 int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot biosbootspecification
====================================================================================
I've nothing telling me it is a 3.03 BIOS version but only got the BIOS file name (68ET35WW);
Is it the same BIOS you used and if not how could I find the list of (token, default value,new seting) for that particular BIOS ?
Thanks a lot in advance for your help !
Regards -
How to enable a disabled iPod that won't connect to internet
trying to enable my disabled 5th generation iPod touch. I have tried connecting to iTunes on the computer, which I couldn't get it to do anything. I then tried using the "Find my iPhone" website and erased the iPod. However, I got a message that says "This iPod will be erased when it connects to the internet". How do I connect a disabled/locked iPod to the internet/wifi while it is waiting to be erased because it won't connect to internet/wifi?
Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Forgot passcode or device disabled
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode. -
How to enable a disabled iPad without losing very important pictures?
How can you enable a disabled iPad without losing very important pictures?
If you have important files, photos, videos which are only on your iPad, you need to backup frequently to your computer or iCloud.
How can I unlock my iPad if I forgot the passcode?
http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
You may have to do this several times.
Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
Cheers, Tom -
how do I enable a disabled ipod touch
Place the iPod in Recovery mode abd connect to your computer and restore via iTunes.
-
How to enable a disabled iphone 4s
my bf bought me a iphone 4s from his friend he was drunk does not remember password there for iphone disabled, how to enable it with out an itune account
You can not. You have to have the Apple ID password. Ask your drunk friend to reset the password and let you erase the phone. Simple.
-
How to enable my disabled iphone.it says connect to itunes
How do i enable my disabled iphone.It says connnect to itunes.Tell me what can i do about it
iOS: Device disabled after entering wrong passcode - Support - Apple
-
How to enable your disabled iPhone
How do I enable my disable iPhone?
You need to restore using the recovery mode as described in http://support.apple.com/kb/HT1212
-
Report Painter:How to change an existing report parameter to a SELECT optio
Hi ,
We have an already existign report, taht exists only in QA, How could we chnage the report such that the existing paramenter period would show up as SELECT option instead of a parameter.
I have no experience with report painter.
Thanks,
Vinotha MI do not have any idea about Report painter and So dont know how I could do this.
Please help with this.
Also this report now does not exist in the development server.
Maybe you are looking for
-
Inserting images into a movie that are not photos
Is there anyway to insert images into an iMovie (such as *.gif) files? Alternatively, is there anyway to insert powerpoint slides into an iMovie (because I can easily get the images into power point). Can I put an image in one of the title frames or
-
Not able to validate the xml document against DTD using SAX
Hi , i am not able to validate xml document against its DTD using SAX parser even after setting setValidating = true. even if the file is not correct according to DTD , it is not throwing any exception. what could be the reason.? please help.. kranth
-
How to save expression together with animation preset?
I am trying to understand expressions and animation presets. I have one single slider control, which controls the opacity of a layer, where the value is the slider value + slightly changed using an expression. I can save the slider control as an anim
-
XMPTextInput control height ignored in Flex 3 Properties
I need to set my XMPTextInput controls so that they have a height of 32. I have tried this in many different ways and none of them work. In Flex 3 in "Design" mode I select the control, open the properties tab and set the height to 32. The control
-
I want to display some fields using the BDC and i want to know thruogh whic
I want to display some fields using the BDC and i want to know thruogh which transaction these fields are displayed.Could you please help me out.