How to enable RDS - AFTER installing

I've got CFMX7 already installed and running. I did not
enable RDS when I installed.
But I want to enable RDS now. Is this possible? If so, how?
Thanks.

Todd-Holtmann wrote:
> I've got CFMX7 already installed and running. I did not
enable RDS when I installed.
> But I want to enable RDS now. Is this possible? If so,
how?
Open /web-inf/web.xml and look for the RDS servlet in it. If
it is
escaped, remove the escape markers and restart CF. Then
enable and set a
password for RDS in the Administrator.
Jochem
Jochem van Dieten
Adobe Community Expert for ColdFusion

Similar Messages

[CF8] Enabling RDS after install on Apache 2.2.4

when I uncomment the RDS sections in web.xml and restart cf,
I only get error 500s
My apache error log says:
Couldn't initialize from remote server, JRun server(s)
probably down.
the mx technote just says to uncomment the code and restart,
I can't find a cf8 technote for enabling. But a cf blogger blogged
about this, and pointed to the cf8 technote for disabling and said
he just followed the directions in reverse and it worked. The
directions were the same as mx- to uncomment and restart.
Am I missing something?

I know you said you were on Apache however, this worked for
me.
After much mucking around with dealing with multiple
instances and having the administrator working then logging out and
having it not work. Charlie Arehart and I found out that if you
enable RDS or Sandbox security you need to manually configure the
jrun.config file.
you need to add soemthing like this to your #argument to VM
setting
-Djava.security.manager
"-Djava.security.policy={application.home}/servers/cfusion/cfusion-ear/cfusion-war/WEB-IN F/cfusion/lib/coldfusion.policy"
"-Djava.security.auth.policy={application.home}/servers/cfusion/cfusion-ear/cfusion-war/W EB-INF/cfusion/lib/neo_jaas.policy"
http://www.talkingtree.com/blog/index.cfm/2006/7/11/SBS-Known-Issues
If you scroll down to Item #4 and then read the whole
inforamtion it works. I just did it this morning. Be sure to back
up your jvm.config file first.

How setup LDAP Sync After Install in OIM 11g ver, 11.1.1.5.0

Hi guys, I'm trying to find how to setup LDAP Sync After Install in OIM 11g (ver, 11.1.1.5)....
I found on Metalink an interesting article "*How to Setup LDAP Sync After Install in OIM 11g [ID 1272682.1]*", but inside there is a Note that says:
Note: This article is applicable to OIM version 11.1.1.3 only. Steps for 11.1.1.5 are not the same, and product manual has documented steps to setup LDAP sync after install.
So, that the steps for 11.1.1.5 are not the same, it's clear.....
and I tried to look for these steps in the manual:
Oracle® Fusion Middleware Quick Installation Guide for Oracle Identity Management
11g Release 1 (11.1.1)
Part Number E10033-06
but I didn't still find nothing for the specific 11.1.1.5.0 version....only for the 11.1.1.3.0 version
Can anyone help me to find where these steps are ? I need this information as soon as possible ti start the development
Thanks in advance for the help
Alex

If you are creating Before and After Create Opeation script, you would be able to access all the variables in the process form. Now obvious question, what are the names of these variables? The answer is: the name of the variable is same as that mentioned in the "decode" column of the provisioning attribute map lookup or in other words, the variable name is same as the AD attribute name. In the example mentioned in the documentation, the variable "%givenName% was used in the script. On the similar lines you can use other variables like "sn", "samAccountName", etc.
Hope the information helps.

How to fix iPhoto after installing idvd

how do I fix iPhoto after installing idvd?

That's because you didin't do a custom install and installed only iDVD.
OT

How do I fix after installing iOS 7.1.2 my iPhone 4s

IiTunes logo and plug in logo come up after installing iOS 7.1.2 my iPhone 4s.i pressed home button and sleep button .it didn't work .

If you can't update or restore your iOS device

How to move files after installing new hard drive

I am considering the installation of a new 80 or 100 GB hard drive. I purchased the new iLife 06 program but I do not have enough space to install on my present 60 GB unit. I only have 3 GB available. I've read all the posts involving the possible brands, downloaded the instructions how to swap out the units. My question is how to backup and install my files and applications so I may reinstall onto the new drive. Can I just copy my hard drive volume onto my external Lacie storage unit and then drag the volume back to the new hard drive after booting off my OS disk? Any advice on how to move my apps and files? Do I need to purchase cloning software?

The easiest way is buy an external firewire enclosure and put your new drive in it. Then format your new drive. then use Carbon Copy Cloner to copy your internal drive onto your new drive. Then install your new drive and put your old one in the enclosure. You are now in business with an external backup on your old drive.

How to enable GPU after effects cs6?

I have a Intel HD Graphics 4000 on my macbook pro. How do I enable the GPU if after effects. It should be compatible but how?
Thanks in advance.

As I said, there is nothing that you need to do to enable the OpenGL features. They just work automatically.
Regarding the CUDA feature, the ray-traced 3D renderer: That feature requires CUDA, which is a hardware architecture that your GPU simply does not have. It is an Nvidia technology that is only on Nvidia GPUs.
This is all explained in the page that I lined to in my previous post.
However, you should not concern yourself with the ray-traced 3D renderer. The ray-traced 3D renderer is an obsolete feature that has been superseded by several better ways of doing 3D in After Effects, including using Cinema 4D (which is included with After Effects now):
http://blogs.adobe.com/aftereffects/2013/04/details-of-cinema-4d-integration-with-after-ef fects.html

Enabling JServer after Install

I cannot find the location of the documetation for post installation steps for enabling JServer functions within an 8.1.5 or 8.1.6 database on Solaris. The banner page shows that Java Options were linking into the kernel, but trying to deploy a servlet fails with messages like:
ORA-29540: class oracle/aurora/rdbms/DbmsJava does not exist
Any help would be appreciated
[email protected]

1. Verify there were no errors from initjvm.sql
If the resources are insufficient the Jserver will not install correctly.
Metalink has posted docs for setup and verification.
DocID: 106260.1 How to test the JVM
DocID: 103855.1 Jserver Installation for Oracle8i
There must be sufficient resources available for a successful install of Jserver.
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Roddj ([email protected]):
I cannot find the location of the documetation for post installation steps for enabling JServer functions within an 8.1.5 or 8.1.6 database on Solaris. The banner page shows that Java Options were linking into the kernel, but trying to deploy a servlet fails with messages like:
ORA-29540: class oracle/aurora/rdbms/DbmsJava does not exist
Any help would be appreciated
[email protected]<HR></BLOCKQUOTE>
null

WRT310N V1 - How to fix firmware after installing firmware v2 on v1 hardware. ** SOLVED **

Hello,
WARNING! THIS IS AN ADVANCED FIX FOR TECHNICAL TECHS WITH OUT OF WARENTEE ROUGHTERS. IF LINKSYS SUPPORT CAN HELP YOU, USE THERE SERVICES FIRST! THIS PROCEDURE MAY RESULT IF PURMADENT LOSS OF USE OF YOUR ROUGHER. THIS WORKED FOR ME, IT MAY NOT FOR YOU!
Situation:
Linksys WRT310n V1
Power LED on solid
LAN Ports LED on solid
Wireless LED off
NO RESPONCE AT ALL!
PC hardware tested (only one is needed):
Vista laptop gigibit card.
Vista desktop gigibit card.
Software to download / install:
Installed vista TFTP client from control pannel
download TFTP from linksys
download firmware from linksys ( Proper firmware for v1 hardware!!!! )
Method and Procedure:
Plug in the power and the lan cable to the computer.
Open a dos prompt start pinging the roughter.
ping 192.168.1.1 -t -w 5
No responce is to be expected at this point.
On the computer open your network connections folder
Disable ALL OTHER network interfaces! (ALL OTHER)
open the settings of the lan interfacess.
disable (uncheck) all options other then tcp/ip v4
set the manual address of the card to
192.168.1.10 ip
255.255.255.0 sub
192.168.1.1 gate
192.168.1.1 dns
now in the network card properties above configure the network card for 10 half duplex speed mine was called line speed and duplex.
save and close.
NOTE: Do not release the reset button untill told to! You will need to hold it in for a long time!
NOTE: when holding the reset for 30 seconds, the LAN port may flash around 5 and 15 seconds, do not pull the power until the lan is off around 25 to 35 seconds of holding
On the rougher, with the power on and the lan cable connected.
Hold the reset button for 30 secconds you will see the lan cable port turn off arround this point pull the power.
Hold the reset and wait 10 seconds.
Hold the reset and power up for 30 seconds until the lan cable turns off around then
Ok so with the power off you can release the reset button.
from now own you can start from here with the reset if first attempts of sending the new firmware to the linksys fails.
Open a NEW dos prompt.
type tftp -i 192.168.1.1 put C:\linksysfirmware.bin
if you hit enter it will fail ... so let it time out... if you did type it again and wait to hit enter.
while holding in the reset button power on the roughter release the reset after 5 secconds.
press enter on the dos prompt. you may send this a couple of time arround now it took three tryes to get the "SENT COMPLETE" message from tftp! you will also magicaly see your pings from the other window start working! if working WAIT 2 min before doing anything next.
If you fail for more then 1 min, unplug your roughter and start the send firmware part.
ok so it's pinging thats all? yes!
ok so you waited 2 min, now pull the power normaly and wait 10 secconds return the power with our the restart! start it normaly.
after 20 secconds the roughter should be able to ping ... nothing else yet!
use the Linksys TFTP program now ... and install the full firmware to the roughter!
when the message says firmware complete wait two min then pull the power and reboot.
DONE!
Solved!
Go to Solution.

[email protected] wrote:
Hello,
WARNING! THIS IS AN ADVANCED FIX FOR TECHNICAL TECHS WITH OUT OF WARENTEE ROUGHTERS. IF LINKSYS SUPPORT CAN HELP YOU, USE THERE SERVICES FIRST! THIS PROCEDURE MAY RESULT IF PURMADENT LOSS OF USE OF YOUR ROUGHER. THIS WORKED FOR ME, IT MAY NOT FOR YOU!
Situation:
Linksys WRT310n V1
Power LED on solid
LAN Ports LED on solid
Wireless LED off
NO RESPONCE AT ALL!
PC hardware tested (only one is needed):
Vista laptop gigibit card.
Vista desktop gigibit card.
Software to download / install:
Installed vista TFTP client from control pannel
download TFTP from linksys
download firmware from linksys ( Proper firmware for v1 hardware!!!! )
Method and Procedure:
Plug in the power and the lan cable to the computer.
Open a dos prompt start pinging the roughter.
ping 192.168.1.1 -t -w 5
No responce is to be expected at this point.
On the computer open your network connections folder
Disable ALL OTHER network interfaces! (ALL OTHER)
open the settings of the lan interfacess.
disable (uncheck) all options other then tcp/ip v4
set the manual address of the card to
192.168.1.10 ip
255.255.255.0 sub
192.168.1.1 gate
192.168.1.1 dns
now in the network card properties above configure the network card for 10 half duplex speed mine was called line speed and duplex.
save and close.
NOTE: Do not release the reset button untill told to! You will need to hold it in for a long time!
NOTE: when holding the reset for 30 seconds, the LAN port may flash around 5 and 15 seconds, do not pull the power until the lan is off around 25 to 35 seconds of holding
On the rougher, with the power on and the lan cable connected.
Hold the reset button for 30 secconds you will see the lan cable port turn off arround this point pull the power.
Hold the reset and wait 10 seconds.
Hold the reset and power up for 30 seconds until the lan cable turns off around then
Ok so with the power off you can release the reset button.
from now own you can start from here with the reset if first attempts of sending the new firmware to the linksys fails.
Open a NEW dos prompt.
type tftp -i 192.168.1.1 put C:\linksysfirmware.bin
if you hit enter it will fail ... so let it time out... if you did type it again and wait to hit enter.
while holding in the reset button power on the roughter release the reset after 5 secconds.
press enter on the dos prompt. you may send this a couple of time arround now it took three tryes to get the "SENT COMPLETE" message from tftp! you will also magicaly see your pings from the other window start working! if working WAIT 2 min before doing anything next.
If you fail for more then 1 min, unplug your roughter and start the send firmware part.
ok so it's pinging thats all? yes!
ok so you waited 2 min, now pull the power normaly and wait 10 secconds return the power with our the restart! start it normaly.
after 20 secconds the roughter should be able to ping ... nothing else yet!
use the Linksys TFTP program now ... and install the full firmware to the roughter!
when the message says firmware complete wait two min then pull the power and reboot.
DONE!
hi
i tried ur all steps but couldn't success, and the different thing is my when I connect my wrt310n to computer I show the IP 169.254.*.* is there any different steps for it. plz help me.

How to enable JavaScript after downloaded ff25 running on Mac OS 10.8

Since I updated to FF25 I can't enable JavaScript which I need for sites I use.
I have the latest Java 7 version 45 but there is no plug-in appearing for Java.
I added Quickjava 2.0.2 I think this is the version, and clicked to enable java.
But when I visit the sites that require JavaScript I get an error message saying JavaScript not enabled.
When I test the java 'latest version' test from Java's web site using FF java cannot be detected, but it can when I do the same test using Safari.
How do I fix this?
Tx Jo

Type '''about:config''' in URL and enter
* In the search bar, search for '''javascript.enabled'''
* Double click on the '''Value''' to change to '''TRUE'''

How to create DAD after install?

I have installed Oracle 10g on Linux server. Then from 10g Companion CD, I installed just Oracle HTTP Server and HTML DB on Windows client. The Windows client has absolutely no other install of Oracle except what is installed by Companion CD. The install of Oracle HTTP Server and HTML DB proceeds without any error. At the end of install, the OUI tell me that the URL is http://<machine>:7777. I connect to the URL and get a page which is Welcome to Oracle HTTP Server. My question is where do I go from here? There is no documentation on how to configure DAD. The page itself has no links to anything of use.
Thanks

156996,
http://download-east.oracle.com/docs/html/B13693_01/post_inst.htm#sthref224
Joel

How to shut down after installing new OS?

Hello,
I am selling my MBP, so I used the Snow Leopard desk to "wipe" my data from the machine, and then I re-intalled OS 10.6. Now the computer is at the "welcome" screen as if it was just purchased at the store. It asks you to select your country, your languge, etc, and then it asks if you are restoring from a Time Machine backup or what exactly you'd like to do.
My problem is (and I know this sounds stupid) I don't know how to turn the computer off now that it's as this "beginning" stage. It doees ot have the usual selections at the top of the screen (like the Apple Menu, etc), so I'm not sure what to do. For now, I just closed the lid and I'm hoping that it worked and it's currenlty sleeping.
But I'd like to be able to shut the machine down so that I can ship it to the new buyer.
Thanks for any help!
PS: I also have the new iLife that I'd like to put on it (it had it before I wiped the data), but I can't figure out how to do that either. The machine is not setup for a user yet, and I don't want to mess it up for the person who is buying it. Is there anything I can do that will allow me to install it?

wjosten wrote:
Not a problem, my reply is directed at others that might view this thread.
My reply was completely correct, other then ejecting the DVD. But then you really don't need to eject it as it is going with the computer anyway.
You can always restart the system and then eject and then hold down the power button to shut the system down again. Once restarted it will go to the First screen again

How to Clear Cache after Install / Uninstall ?

I love Installing / Uninstalling in Windows Phone ( Lumia 800 - WP7.8)..
its so easy... any other OS cant beat it.. But i want to know how to clear the Cache (if at all exists)?
i think there should be some way to clear it??
and what's the best antivirus or malware or spyware for WP7.8?
Solved!
Go to Solution.

You dont need spyware or antivirus.
TO CLEAR CACHE ON BROWSER?
From the Home screen, tap Internet Explorer.
From the lower right corner of your screen, locate and tap the icon consisting of three dots.
Select settings.
Tap delete history.
Tap delete to confirm.
Close and relaunch your browser.
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Hp webcam : How to enable it after refreshing pc

I have the HP envy 15 notebook.I refreshed my pc but after it when i went to the camera app it said that it needs permission for it to be used.The camera app says that you can change it in the camera app settings.
But i do not know how to go to it's setting
It would be helpful if i get an answer in simple numbered steps
Thankyou.

Hello @MaryBeats,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that your camera app indicates that you need permission to use it after refreshing your computer. Did you have HP SimplePass protect this application previously? I would be happy to help you, but first I would encourage you to post your product number for your computer. Below is a is an HP Support document that will demonstrate how to find your computer's product number. In addition, it will also help if you indicate which operating system you are using; and whether your operating system is 32 or 64 bit. The more information you can provide, the better!
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
Cheers!
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Hp g60 418ca, how to restore sound after installing windows 8.

I installed Windows 8 on hp g60 418ca. I have tried all troubleshooters, guidelines, etc. but have not succeeding in getting the sound working. There are no windows 8 drivers, but I've tried the W7 and Vista drivers using various compatiblity modes. I've tried to let W8 update the driver. The devices DO show up in control panel/device manager and when I test them the volume level bars move up and down, but no sound comes through speakers and/or headsets.
Do I just need to wait for HP to release drivers... what is the best approach?

Hi doug_125,
More than likely HP is not going to support hardware for W8 on any system purchased before Oct 1st 2011. Some updates for W8, most W7 drivers will work in W8.
If you still had Windows 7 installed, you could run the Upgrade assistant software, it will scan your PC and generate a report on what is currently installed on your PC is compatible with W8.
http://goo.gl/z8LVf
Here is a document for covering upgrading to Windows 8 http://goo.gl/CO6uV
The document is fairly extensive, covering all sorts of issues. There is a section about audio drivers. Perhaps it will help.
Please let me know if it does help.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

How to enable RDS - AFTER installing

Similar Messages

Maybe you are looking for