How to enable wake on lan on Thinkpad Twist?

I have a Thinkpad Twist purchased because of the presence of the ethernet card.
Unfortunately I can not turn wake on lan.
I did several searches and several attempts without success.
Someone managed to enable wake on lan?
Thank you.
(sorry for the English by Google Translate)
Solved!
Go to Solution.

Hey there Cello67,
To enable Wake On Lan on a Thinkpad twist:
1) You will first need to power down your laptop completely.
2) Then turn it on, as soon as you turn it on start hitting the enter key to interrupt start up. This will take you to a start up menu.
3) From here you will need to enter your BIOS.
4) Move right over to the Config, then press enter on the Network Selection 
5) The first option you should have is Wake On Lan. You can change this from disabled to either AC Only or AC and Battery.
After you have done this save your settings, and resume startup. Once the computer has finished booting go to your desktop, and pull out your charm bar by pressing Win Key + C or with a swipe from the right side of your screen in. From here you will:
1) Enter the Control Panel
2) Device Manager - > Your Ethernet Card/Adapter
3) Click the Power Management Tab
4) Select "Allow this device to wake the computer"
Hope this helps Cello67!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

Similar Messages

  • How to enable Wake On Lan on MSi P45 Neo2?

    Hi,
    I just bought a P45 Neo2, and I think I have WOL on this machine, as the Realtek chipset 8111C does support the feature. However, I'm not sure how to
    - enable
    - use
    the function. Can you help me?
    Under Device Manager, I go to the Realtek network adapter --> Properties --> Power Management --> Allow this device to bring the computer out of standby.
    Now, it is enabled. How should I use it? I would be very thankful :-).

    Please have a look here first for basic introduction to Wake on LAN and "Magic Packets":
    http://en.wikipedia.org/wiki/Wake-on-LAN#How_it_works

  • How to Enable Wake On Lan over the Internet??

    Hi, I am using RV220W with the latest firmware, I want to make "Wake on LAN" work for my NAS, I found the following description on Internet:
    "If you wish to use Wake On Lan over the internet you will need to set up your destination firewall/router to allow "Subnet Directed Broadcasts". Most routers and firewalls disable this option by default.
    You will then need to allow traffic through on your firewall/router on a specific port. The choice of ports is up to you."
    So how can I enable "Subnet Directed Broadcasts" on RV220W??
    Thanks.
    Raymond

    Hi Jasbryan,
    If RV220W doesn't forward UDP to a broadcast address, could you ( i.e. Cisco) provide a tools for sending WOL Magic Packet to the LAN on Router Device Manager page?
    I see many routers also provide this tools from their manager page.
    Thanks.
    Raymond

  • How to enable Wake-On-Lan on HP touchsmart 7320PC (LH183EA)?

    LH183EA

    HI
    Press F10 to access Computer setup option
    once in HP setup utility you need to select Security menu option
    in security there is network boot option, just need to enable it

  • How may I enable Wake On Lan on the B570-1068AFU

    Hi all, I have the B570-1068AFU. I want to enable Wake on Lan on this laptop, but I do not see a bios setting for it. Is it possible with this Laptop? Thanks.

    Hi Jasbryan,
    If RV220W doesn't forward UDP to a broadcast address, could you ( i.e. Cisco) provide a tools for sending WOL Magic Packet to the LAN on Router Device Manager page?
    I see many routers also provide this tools from their manager page.
    Thanks.
    Raymond

  • How do I enable "Wake on Lan" P1102W

    iMacs, running 10.6.8, Airport Extreme, Laserjet P1102W with fixed IP address.  Once it goes to sleep, how do I wake it up?

    I changed the wireless security setting on my wifi router to use "WPA-PSK [TKIP] + WPA2-PSK [AES]" instead of "WPA2-PSK". 
    I guess the printer has a problem with the newer version of WPA2.
    Now it continues to be available even after it goes into powersave mode.
    Try it - ymmv.  It took a stroke of luck and 12 months of frustration to figure this out.

  • How to configure Wake On LAN to work through the Internet?

    I'm using an iOS app to wake my desktop computer. It works perfectly fine when I'm within my WiFi range. However, when I'm out of my Linksys E3000 access point, it no longer works over the Internet. So, if anyone can point me to documentation that have step by step instruction on how to configure this through the Linksys E3000 access point, I'll be grateful.

    Hi ohgosh,
    I believe your computer is already configured and has all the requirements for Wake on Lan since it works locally. To do it remotely you need to open the regular port numbers used for WOL like UDP ports 9 and 32767. Your desktop IP address must be set to static because that's what you need to enter on the port forwarding page of your router. You may use this link below for instructions on how to do port forwarding on your router.
    http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=d9b27a0c1bb9496d8c22d0d55f875ddf_17241.xml&pid=80&...
    Another option is to set up DynDNS on your router. With this, you need to subscribe to DynDNS.com. I found some online links that could help you enable WOL remotely:
    http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=3ff9013e9f4f4a0b9d9805b0697407b7_4578.xml&pid=80&r...
    http://lifehacker.com/5786791/rule-your-computer-from-afar-by-setting-up-wake+on+lan
    http://www.dslreports.com/faq/9389
    http://www.teamviewer.com/en/res/pdf/TeamViewer-Manual-Wake-on-LAN-en.pdf
    Hope this helps!

  • Enable wake on lan

    Hi,
    Can someone tell me if the 865PE neo fis2r has wake on lan?
    If so, how do you enable it or is at already enabled?
    I can't find a thing in the bios to activate this.
    According tomshardware and other reviewers this mobo should have it, but where ...
    Thx
    David.

    Hi Orblivian
    Which 865 is it exactly?  
    The more info you supply the quicker the solution......
    Try and create a sig file by going to your profile tab and the signature....... Please use mine as an example.....people from all around the World read.......so if they have same system, they may have found a solution already.....
    Oh....shot in dark.....it should be under POWER MANGEMENT FEATURES
    Del

  • SG200 how to configure Wake on LAN across subnets

    How can I configure  to support WOL on a SG200 (8 Ports) to support Wake On Lan (Magic Packets) from a different IP Subnet or other SG200 Switch. It seems not to support Directed-Broadcasts.

    I checked out the link and tested the changes. Unfortunately, the WOL still won't work. In the link you attached, it states that you cannot turn on a computer that is off. Does that mean one that is off such as unplugged or in shutdown? Also, one of the steps to configure the firewall access rules says to block all outbound connections for all services. That doesn't make any sense to me, but I might be wrong. I also noticed that the link was for another router. I don't know if that makes a difference. I also read somewhere in the forums that someone else is having a similar problem, saying that Port Forwarding still isn't working in the latest firmware. This whole problem is strange because it used to work all the time on my old router with Port Forwarding, but on this one it won't work at all.
    Sent from Cisco Technical Support iPad App

  • How to disable wake on Lan on 865PE LS

    Both led on the lan is on all the time, even when computer is turned off, i disabled wake on PME setting in the bios, and i also disabled all the wake on setting in the network card properties in XP, but led's are still on all the time, is there a another way to disable wake on lan ??

    I have three other computers connected to the same router, none of them have lan led on when turned off, and i think there is no reason for the leds to be on if you don't use the wake on lan function
    in the power management, "allow this device to turn on the computer" is unchecked, i can't think of any other settings,this never happen before with my other lan card, i mean its not a big deal to have the leds on, but its nice to know how to turn them off to save some power.
    any thoughts??

  • SA520W - how to enable communication between LAN Devices?

    We install our new SA520W Security Appliance. Wireless is setup and Internet works fine.
    But we want to PING another computer inside the LAN it does not response. We can not see other computers, printers or devices even they are in the same network, same IP range by wire or wireless. Is there something we need to enable in Utilities?
    We have shared folders and printers on the network, so we had to come back to our old router. Please help.
    Thanks,
    AJ

    By default the SA520w isolates wifi clients from each other.  The setting you are looking for is AP isolation under APN settings. this needs to be switched off
    For more details see page 108 in the manual
    hope this helps
    Julian

  • G710 Wake On Lan

    Hi all,
    I am trying to figure how to enable Wake on lan on G710 laptop.
    It works while in sleep mode but not in hibernate or shut down.
    Is this laptop cabaple for Wake On Lan in hibernate and shut down?
    Will kindly appreciate any help...
    Thanks
    Benny
    Solved!
    Go to Solution.

    hi benny_ru,
    Welcome to Lenovo Community Forums!
    This may not be possible. Since this is not supported in BIOS
         When the computer is in Hibernate and/or in shutdown state it need to cross the BIOS to wake up the computer or turn it on.
          Sleep will be ok since the LAN card supports it and it is the OS that wakes the system up and not the BIOS.
    Regards
    Solid Cruver
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • HP Envy 15 Wake on Lan

    Does anyone know how to enable Wake on Lan in the BIOS? 

    Using reverse language, please read step 6 of this document for settings.
    I am a volunteer. I am not an HP employee.
    To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
    The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
    (2) HP DV7t i7 3160QM 2.3Ghz 8GB
    HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
    Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Both Customs use Rosewill Blackhawk case.
    Printer -- HP OfficeJet Pro 8600 Plus

  • Satellite C660 - how to enable and Use WAKE ON LAN?

    Hi All,
    I previously posted asking about using Wake on Wireless LAN and was very helpfully advised that this was not possible, so I have started to explore the Wake ON LAN option.
    I have a Toshiba C660 PSC0LE-00500JEN and have enabled Wake ON LAN on the BIOS, and have connected a LAN cable between my wireless router and the laptop, both of which recognise each other so the cable seems ok.
    However, whether I use a WAKE ON LAN app on my android, or I use an online "wake on lan via browser" site, the laptop still remains asleep.
    Can anyone advise?
    Thanks
    James

    Hi
    The Wake Up on Lan option would work if you would send an Magic Packet to the remote machine (notebook).
    I have no experience using the Android app who knows if it function properly
    Try other method. For example using an software like Wake on Lan for Windows Graphical User Interface (GUI)
    Google for that to download this software.
    Furthermore go to device manager -> LAN card -> Properties -> Advanced tab and check here if the WOL is enabled too

  • M93p BIOS issue: PowerOff not correct if Enhanced Power Saving Mode Disabled and Wake on Lan Enabled

    Hi Levnovo support team, Recently I bought a M93p tiny(10AAA05MTW)(BIOS revision FBKT56A)and installed with Ubuntu 13.10 myself.Then tried to enable wake on lan for my tiny. The followings are my test result. 1. Enhanced Power Saving Mode Enabled, no mateter what is Wake On Lan setting     PowerOff system is OK. 2. Enhanced Power Saving Mode Disable and Wake On Lan Disabled    PowerOff system is OK. 3. Enhanced Power Saving Mode Disabled and Wake On Lan Primary or Automatic   PowerOff system is NG.   When I tried to power off system, it always can poweroff(LEDs on front all off) then POWER ON again in 2 or 3 seconds.   I cannot accept this test result ,system should poweroff not reboot again.   It's really hard to understand why enabling Wake on Lan will affect power off function. I tried the same procedures with my another M92p(3212A16)(BIOS revision 9SKT70AUS), and it works well.   

    Did you ever get a fix for this?Having the same issue on 3 of 6 machines that just arrived. 

Maybe you are looking for

  • How can I call a RFC from dynpage ?

    Hi! I would like to know how can I call a RFC from a Portal aplication, dynpage or jspdynpage. there include some libraries ? any idea? thanks

  • Count of rows in a schema tables

    Hi, i wrote a script to get all the select count(*) from test; i have about 70 tables select statements spooled to a file. so far is ok but i want to see the table name in thsi so i know for what table these counts are for how to do this. urgent plea

  • Error during invokation of webservices: "error: unknown java type:"

    hi, I'm having issues with invoking a webservice from the "WebLogic Test Client". The webservice exposes the methods from a stateless session EJB and Weblogic Workshop was used to create the webservice controls Weblogic version: 10.0 mp1 Pls. advise.

  • How to create dynamic calc account in multi-plan type application

    Hi expert, I have a planning application with 3 plan types. I created a calculation script which fixed on accounts in plan type 1 only and the calculation suppose to calculate a "dynamiccalc" account with a member formula attached. Everytime I run th

  • Smooth scrolling in mx:Datagrid

    Hi All, I am implementing a datagrid in my extension for Illustrator CS5, 6. I want to have smooth scrolling in it as there are images that are displayed in the grid. I am using an ItemRenderer for displaying images. It has one column. I searched the