How to Enable Wake On Lan over the Internet??

Hi, I am using RV220W with the latest firmware, I want to make "Wake on LAN" work for my NAS, I found the following description on Internet:
"If you wish to use Wake On Lan over the internet you will need to set up your destination firewall/router to allow "Subnet Directed Broadcasts". Most routers and firewalls disable this option by default.
You will then need to allow traffic through on your firewall/router on a specific port. The choice of ports is up to you."
So how can I enable "Subnet Directed Broadcasts" on RV220W??
Thanks.
Raymond

Hi Jasbryan,
If RV220W doesn't forward UDP to a broadcast address, could you ( i.e. Cisco) provide a tools for sending WOL Magic Packet to the LAN on Router Device Manager page?
I see many routers also provide this tools from their manager page.
Thanks.
Raymond

Similar Messages

How may I enable Wake On Lan on the B570-1068AFU

Hi all, I have the B570-1068AFU. I want to enable Wake on Lan on this laptop, but I do not see a bios setting for it. Is it possible with this Laptop? Thanks.

Hi Jasbryan,
If RV220W doesn't forward UDP to a broadcast address, could you ( i.e. Cisco) provide a tools for sending WOL Magic Packet to the LAN on Router Device Manager page?
I see many routers also provide this tools from their manager page.
Thanks.
Raymond

This is how to wake your desktop over the internet via WRT54GS!

Assuming you've read how to configure the BIOS and Network adapter, this is what needs completed on the router. If you search this subject you'll discover a gazillion threads about failure. I tried hard for several weeks, only being able to wake it over my LAN, but never over the internet and then abandoned the whole idea months ago, but tried it again today with success. I had my brother in law test the configuration from 500 miles away - Indiana to PA. I Port Forwarded and Port Triggered to port 1649 but you can select a different port. I enabled Wireless Access and Remote Management in Administration. Months ago I believe I'd tried Port Triggering without the Administration settings and, with Administration settings enabled, without triggering. Now the most interesting thing is after the initial test I re-enabled the routers Firewall and I was still able to wake the PC. I also set up a rule in my software firewall to open port 1649. I'm not sure that is necessary, since in theory the pc and the firewall are off. Now my external IP is not static, however, it never, never, ever changes so all other settings were just default. One thread I read one time was a person could only wake the PC in the first 30 seconds after shutdown. I haven't tested that problem. I'm also going to retest Port Triggering without Wireless Access and/or Remote Management enabled. Give it a try and good luck!
I edit! So I just woke it up without Wireless Access and Remote Management enabled or the port open in the software firewall. I went through a VPN tunnel, however, not 100% sure that is a valid test. It would seem that triggering and not just forwarding maybe the key!
Message Edited by ratchet on 11-08-2008 11:01 PM
Message Edited by ratchet on 11-09-2008 04:27 AM

Hi Jasbryan,
If RV220W doesn't forward UDP to a broadcast address, could you ( i.e. Cisco) provide a tools for sending WOL Magic Packet to the LAN on Router Device Manager page?
I see many routers also provide this tools from their manager page.
Thanks.
Raymond

How to enable wake on lan on Thinkpad Twist?

I have a Thinkpad Twist purchased because of the presence of the ethernet card.
Unfortunately I can not turn wake on lan.
I did several searches and several attempts without success.
Someone managed to enable wake on lan?
Thank you.
(sorry for the English by Google Translate)
Solved!
Go to Solution.

Hey there Cello67,
To enable Wake On Lan on a Thinkpad twist:
1) You will first need to power down your laptop completely.
2) Then turn it on, as soon as you turn it on start hitting the enter key to interrupt start up. This will take you to a start up menu.
3) From here you will need to enter your BIOS.
4) Move right over to the Config, then press enter on the Network Selection
5) The first option you should have is Wake On Lan. You can change this from disabled to either AC Only or AC and Battery.
After you have done this save your settings, and resume startup. Once the computer has finished booting go to your desktop, and pull out your charm bar by pressing Win Key + C or with a swipe from the right side of your screen in. From here you will:
1) Enter the Control Panel
2) Device Manager - > Your Ethernet Card/Adapter
3) Click the Power Management Tab
4) Select "Allow this device to wake the computer"
Hope this helps Cello67!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution".! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.

How can I download a file over the internet from a WebDAV server?

I am trying to download a file over the internet from a WebDAV server. I've tried doing it with Datasocket as suggested in these articles,
<a href="http://digital.ni.com/public.nsf/websearch/f3cc5f7e60a75cb2862567e700696abf?opendocument">Retrieving an Unformatted Text File via FTP or HTTP Using DataSocket</a>
<a href="http://digital.ni.com/public.nsf/websearch/4FA09E7B3674DA34C1256BD400555C41?OpenDocument">Download a Text File from a Password Protected URL Using DataSocket</a>
but all I get is error 1181 (protocol unrecognized by Datasocket).
I know I have the URL correct, because I can put it into a web browser and it works fine - I can download the file manually.
But I want to have a LabVIEW program do the download automatically.
I have the internet toolkit, but don't have the foggiest clue how to use it, and am using LabVIEW 7.1
I am a bit out of my depth here, so any advice welcome.
Regards,
Mark.

MIG,
What is the URL to the website? Is it an FTP site? The articles you referenced are for specific transfer protocols. If the stie you're trying to get to doesn't follow these protocols, then you'll get the error you're seeing. You may have to use ActiveX to control IE and download the files programmatically.
Chris C
Chris Cilino
National Instruments
LabVIEW Product Marketing Manager
Certified LabVIEW Architect

Can someone point in the right direction for how to make a multiplayer game over the internet

Hello,
I am looking into making a game where two people who can be in different places would log on to the app, log in and can play - i.e. they would be connected over the internet. I'm looking for a hint on what is the direction to take and which technologies.
For example is there a best practice for example if you make an app with DirectX and C++, and you use some kind of web service or something? or is it easier using C# and XNA? just looking for some pointers in the right direction. I have played around
with DirectX, far from proficient but have familiarity, I have no experience with XNA but hear it's less hardcore and easier going. I'm particularly interested in what the best way to connect over the internet.
Thanks

What you are asking is very complicated and one of the more difficult things you can do in gaming. I'd strongly recommend you start smaller to learn and then move up to multi-player games as your skills grow.
From the multiplayer client perspective it doesn't really matter which technology you use. You can write a multiplayer game in any engine or technology that can talk to the network. Choose the client technology that you are most adept at and interested in
and learn it. You can go straight to DX, use a third party library such as Monogame (XNA isn't supported for Windows Store apps), or a complete game engine such as Unity. Once you can write a decent one-player game you'll have the foundation to start on to
build a two-player game.
At that point you'll need to define the problem much more specifically. As you state it, it is really wide open. How do you want the users to connect? Directly machine to machine? Matched through a web server but running client side? Connecting to a game
running on a remote server? Something else?
The network connection itself is probably fairly straightforward, but where to connect and how to manage that can be difficult. You'll have to decide what properties you want. Is this an action game where responsiveness is important or
a turn based game where timing is less relevant?
Are the players connecting locally or completely remotely? If the former then they can probably connect directly over the local network (NFC is great here). If the latter then they probably will need to connect to a matchmaker service to avoid firewalls.
This can get very complex, but there are existing solutions you can use rather than writing your own.
--Rob

How to send an iTunes song over the internet

In my iTunes library I have a song, I want to send, over the internet, to a friend.
How to do that?

Open iTunes Store, find the song then Gift him the song.

How do you use lightroom catalogs over the internet?

We are new to Lightroom 2 and have a variety of questions - we appreciate any information to get us started.
We would like to store our catalogs on our server if possible I am at a remote location so I would need to do this over the internet
Suggestions on how we can best get our photos into lightroom and both be able to access them?
What size catalog can you send over the internet?
What are the advantages/disadvantages of 1 vs. using many catalogs?
How do you share catalogs?
Thank you!

We do not have a network - but we have a server -wuold it be possible to access the catalolg/s from there?
Thanks

How to get Profile Manager working over the internet?

I've set up profile manager at home and it work great on my local network. Now I wanted to make it work over the internet but I can't figure out how to do so. I've already opened the required ports. When I try accessing the User Portal trought my <external ip>/mydevices it asks me whether I trust a certificate or not, but when I choose "ok" it keeps requesting the URL forever until it times out. Am I required to have a registered domain name to access my server or I can just use my external IP ? Is there anything else I should do in order to have it working?

First off, you say you've opened 'the required ports', but which ones are they, in your opinion?
That may sound like a dumb question, but it isn't meant to be. You'll need port 443 to support HTTPS connections, and 1640 for the Certificate Enrollment server.
Additionally, you WILL need a valid domain for this - at least if you don't want authentication errors. SSL certificates rely on the hostname (amongst other things) to provide validation and if you access the site via IP address that validation is doomed to failure. That shoudkn't lead to the problem you're experiencing, which is no response at all, but it's still an issue to resolve.

How to share videos with family over the internet

I have a ton of home videos that I have edited with Final Cut and I would like to find a way to share those with family and friends across the country. Is there any way to do this in the Apple ecosystem. If not, what do most recommend as the best way to do this? Thanks

Thanks for the reply... I'm actually looking for something that would allow me to have all the content available in a library so friends and family can see all the content and then choose what to watch. Ideally, it would be like iTunes or iPhoto only that it could be accessed by multiple people from all over the internet. I think Apple is missing a huge niche in this area.

How to enable Wake On Lan on MSi P45 Neo2?

Hi,
I just bought a P45 Neo2, and I think I have WOL on this machine, as the Realtek chipset 8111C does support the feature. However, I'm not sure how to
- enable
- use
the function. Can you help me?
Under Device Manager, I go to the Realtek network adapter --> Properties --> Power Management --> Allow this device to bring the computer out of standby.
Now, it is enabled. How should I use it? I would be very thankful :-).

Please have a look here first for basic introduction to Wake on LAN and "Magic Packets":
http://en.wikipedia.org/wiki/Wake-on-LAN#How_it_works

How do I share a folder over the internet with Mountain Lion server?

I am new to using formal servers. In Snow Leopard I was able to use web sharing to serve a small website and if I wanted to share a folder with someone I would just provide the person I wanted to share a file with the path to the file inside the sites directory. With Mountain Lion this functionality was removed from the sharing section of system preferences.
I purchased mountain lion server and was able to restore the website serving ability, but I haven't been able to figure out how to share a folder. I am still looking over what documentation I can find, but for the most part it just tells me to set up the services without telling me how. Any assistance would be helpful. Networking is not my area of expertise.
Best Regards,
David Finell

I purchased server to assist with this as I am unfamiliar with the command line protocols for using apache. Because of the UNIX architechture of OSX and I presume apache, I am uncomfortable using the command line for fear of causing serious problems.
Unfortunately, the documentation that I have seen for mountain lion server is wanting in either its completeness or layout/functionability. To summarize the server instructions as I understand them. It just says to configure it and my system to meet my requirements without telling me how.
I am confident that both the apache command line and server are capable of accomplishing what I was able to do before under snow leopard. I just haven't figured out how.
I was able to provide a link to family and clients like http://ipaddress/~user/folder
This no longer works.

How can I remotely access files over the internet using iPhone? VPN? Do I need to use Server?

Please forgive my ignorance here, as I'm a Windows expert but have only been using Mac for two and a half years. Is it possible to securely access predefined directories on my iMac from a remote computer or device over the inernet, be it a MacBook Pro, iPhone or even a Windows computer or Android phone? Is there an advantage to an Apple-only approach (iPhone and Macs)? Do I need to use Server? Is VPN the method of choice, or is there some other method? I'm not looking to do remote desktop control, just remote file access. Right now I'm using DropBox for the things I need most, but I absolutely will not put sensitive information in there, and soon I will need to have access to more than what DropBox can hold. Also it may be worth noting that I'm currently an Android user but will be going back to iPhone soon if it would be advantageous in this regard.
Thanks!
Daniel

If you desire security, you definately want to use VPN so Lion Server will work. Otherwise, if you have sysadmin experience (or know someone who does), there are free alternatives out there for vpn that can be setup on a cheap linux server and provide the same capabilities.

How to enable Wake-On-Lan on HP touchsmart 7320PC (LH183EA)?

LH183EA

HI
Press F10 to access Computer setup option
once in HP setup utility you need to select Security menu option
in security there is network boot option, just need to enable it

How to access my hard drive over the internet?

Hi,
I would like to be able to access my hard drive while I am away from my desk. I am not running OS X Server. How can I do this?
Also, I am behind an Airport Base Station. Which ports would I need to open up?
Besides my Firewall and my Administrator password, how else can I secure the access?
thank you....

VPN does not allow you to control your computer remotely, you are probably thinking of VNC. A VPN essentially extends your local network so that you can access it remotely. You can control your host computer to more than you can control any other computer by accessing it over your LAN.
I still think a VPN is the best option, but it's not easy to install (MacOS X server has a VPN with a GUI built in). OpenVPN is a great option, and there are several GUI interfaces for it (look for these on www.versiontracker.com). This is best because it is secure and will allow you to access your entire hard drive.
Like I said in the last post, WebDAV is also an option. This is what a .Mac iDisk is. This will only allow you access a specific folder (or set of folders) that reside in the Apache (var/www) directory. Although you can always make an alias to the apache directory and keep it in your Documents folder.
A third option that I didn't state before because it's probably the least best is to use NFS to access your home computer. This will allow you to access your entire hard drive. The downside to this is that there is no encryption, nor a password. For security, it uses IP or domain addresses. So this is not an option unless you will to accessing your hard drive from a computer (or a few computers) with (a) static IP address(es).

How to Enable Wake On Lan over the Internet??

Similar Messages

Maybe you are looking for