How to enable web services for the HP envy 4500

I am settin up my new HP ENVY 4500, have the printer working to my wireless rounter but am unable to connect to web services so I can update the printer. How do I do this?

Hi,
Have you activated it yet ? Looks like the setup is not right or missing, it's not connected to the internet. Please use the following tool to run the setup:
http://ftp.hp.com/pub/softlib/software12/COL50403/mp-122330-1/hppiw.exe
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

How to enable Web services for CP 1525nw

Hi,
I am unable to use ePrint for LaserJet CP 1525nw. Printer connected over WiFi. Tried to Enable Web services and saw the message "Connection error Check connection". Firmware is up-to-date. Use the printer in different applications on PC, iPad and iPhone. Everything is working well not ePrint. HP diagnostics did not describe any problems.

Hello Prophet097,
Setting manual network information may help the enabling of Web Services for ePrint on your printer.
To do so:
On the printer's control panel, press "OK" two times to access the reports menu.
Press the right arrow to select "Network Summary" and press "OK" to print the report.
Open an internet browser on a computer within the same network as the printer.
In the address bar, type the printer's "IPv4 Address" and press "Enter", this should take you to a page about your printer.
Click on the "Network" tab at the top of the page.
Click on "IPv4 Configuration" on the left-hand side.
Click the bubble to the left of "Manual" to allow you to input manual settings.
Input the same information from the "Network Summary" into the fields for "IP Address", "Subnet Mask", and "Default Gateway".
Note- None of those fields should be "0.0.0.0"0 or "169.254.xx.xx". If they are, there maybe network issues with the printer.
In the "Preferred DNS Server" and "Alternate DNS Server", this could vary by the size of your network.
-Preferred DNS Server- If you are on a small network, input the same value as the "Default Gateway".
-Alternate DNS Server- If you are on a small network, input either "0.0.0.0" or "8.8.8.8."
Note- If you are on a domain, you may have specific DNS Server information that needs to be in the fields.
Click "Apply" on the page.
Power the printer off and then on.
Try to enable Web Services again.
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Enable web services for hp envy 5530

I keep getting enable web services when I am trying to scan a document. I have clicked on yes about a million times but it wont let me move forward with scanning my documents. I am using MAC OS system.

Hi @cixxpac77,
Welcome to the HP Support Forums. I see that you are getting a message to enable the web services on your Envy 5530 printer when trying to scan.
From your description I suspect that you are trying to use the scan to email feature of your printer. This feature requires that you setup the ePrint feature of the printer.
The first step is to please ensure your printer is connected to your wireless network. This can be easily accomplished from the front panel of the printer using the Wireless Setup Wizard. If you are unsure how to do this, the steps can be found in your User Guide on page 55 in the section titled “To connect the product with the Wireless Setup Wizard”.
Once the printer is connected to your wireless network, let’s enable web services. The steps to enable the web services can be found in the Getting the Printer Claim Code document. If you wish to customize the printer’s ePrint email address I have included the Setting Up a Custom Email Address for HP ePrint document.
If you encountered an connection error message when trying to enable web services, please set a manual IP address and manual DNS servers for the printer. I have included a link to another post with the steps, including screenshots, on how to do this. Don’t worry that the screen shots are for an Officejet 4630 the steps are the same.
Please let me know the outcome.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Can't enable web services for groups (wiki) in WGM

I'm having trouble creating a wiki on my server. More specifically, in WGM, I cannot enable web services for a group. The pull-down menu is accessible, but the only option is "(None)."
I have users and groups set up in OD (they are not local).
I have a working default web page.
I have web services enabled in Server Admin.
I can create and access user blogs.
My user and group folders are on a raid drive instead of the main drive - I'm wondering at this point if there's a problem with a folder name or permissions. WGM just doesn't seem to recognize that there's a site on my server.

OK - wikid is failing to start.
2/5/09 1:36:17 PM com.apple.wikid[37723] Removing stale pidfile /var/run/wikid.pid
2/5/09 1:36:17 PM com.apple.launchd[1] (com.apple.wikid[37723]) Exited with exit code: 1
2/5/09 1:36:17 PM com.apple.launchd[1] (com.apple.wikid) Throttling respawn: Will start in 9 seconds
From the wikid error log:
2009-02-05 13:36:17-0600 [-] Log opened.
2009-02-05 13:36:17-0600 [-] twistd 2.5.0 (/System/Library/Frameworks/Python.framework/Versions/2.5/Resources/Python.app/ Contents/MacOS/Python 2.5.1) starting up
2009-02-05 13:36:17-0600 [-] reactor class: <class 'twisted.internet.selectreactor.SelectReactor'>
2009-02-05 13:36:17-0600 [-] twisted.web.server.Site starting on 8086
2009-02-05 13:36:17-0600 [-] Starting factory <twisted.web.server.Site instance at 0x2eb19e0>
2009-02-05 13:36:17-0600 [-] twisted.web2.channel.http.HTTPFactory starting on 8087
2009-02-05 13:36:17-0600 [-] Starting factory <twisted.web2.channel.http.HTTPFactory instance at 0x2eb1648>
2009-02-05 13:36:17-0600 [-] set uid/gid 94/94
2009-02-05 13:36:17-0600 [-] Traceback (most recent call last):
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/bin/twistd", line 21, in <module>
2009-02-05 13:36:17-0600 [-] run()
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/scripts/twistd.py", line 27, in run
2009-02-05 13:36:17-0600 [-] app.run(runApp, ServerOptions)
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/application/app.py", line 379, in run
2009-02-05 13:36:17-0600 [-] runApp(config)
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/scripts/twistd.py", line 23, in runApp
2009-02-05 13:36:17-0600 [-] _SomeApplicationRunner(config).run()
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/application/app.py", line 158, in run
2009-02-05 13:36:17-0600 [-] self.postApplication()
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/scripts/twistdunix.py", line 213, in postApplication
2009-02-05 13:36:17-0600 [-] startApplication(self.config, self.application)
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/scripts/twistdunix.py", line 183, in startApplication
2009-02-05 13:36:17-0600 [-] app.startApplication(application, not config['no_save'])
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/application/app.py", line 400, in startApplication
2009-02-05 13:36:17-0600 [-] service.IService(application).startService()
2009-02-05 13:36:17-0600 [-] File "/usr/share/caldavd/lib/python/twisted/application/service.py", line 233, in startService
2009-02-05 13:36:17-0600 [-] service.startService()
2009-02-05 13:36:17-0600 [-] File "/usr/share/wikid/lib/python/apple_utilities/service.py", line 62, in startService
2009-02-05 13:36:17-0600 [-] SettingsManager.globalSettings.rebuildIndex())
2009-02-05 13:36:17-0600 [-] File "/usr/share/wikid/lib/python/apple_utilities/SearchManager.py", line 424, in buildAllIndexes
2009-02-05 13:36:17-0600 [-] buildSearchIndex(aPath, doRebuild)
2009-02-05 13:36:17-0600 [-] File "/usr/share/wikid/lib/python/apple_utilities/SearchManager.py", line 406, in buildSearchIndex
2009-02-05 13:36:17-0600 [-] GroupSqliteIndex.buildSearchIndex(whichPath, forceRebuild)
2009-02-05 13:36:17-0600 [-] File "/usr/share/wikid/lib/python/apple_utilities/GroupSqliteIndex.py", line 551, in buildSearchIndex
2009-02-05 13:36:17-0600 [-] con = sqlite.connect(indexDBPath, isolation_level=None)
2009-02-05 13:36:17-0600 [-] sqlite3.OperationalError: unable to open database file
I would like to fix this without reinstalling. If there's a way to restore this specific database file or any part of the wiki, I would prefer to do that. Does anyone have an idea what files I should check/restore?

After i installed updates for my mac mini server, the web services for the server app wont start, it gives an error massage: "Error Reading Settings"

After i installed updates for my mac mini server, the web services for the server app wont start, it gives an error massage: "Error Reading Settings"
The system logs reads:
Mar 29 22:06:25 server servermgrd[82]: servermgr_web: Error Domain=XSServerFoundationErrorDomain Code=4 "Failed to read settings: Exception:
          undefined method `downcase' for nil:NilClass
          ." UserInfo=0x7fc547901080 {NSLocalizedDescription=Failed to read settings: Exception:
          undefined method `downcase' for nil:NilClass

To check the local network for some of the common configuration problems, launch Terminal.app and issue the following diagnostic command:
sudo changeip -checkhostname
That'll report some local configuration information and then either no errors detected and no changes required, or it'll point to whatever configuration errors or issues it might detect. That doesn't catch everything, but it catches the common errors.
FWIW, 192.168.0.0/24 and 192.168.1.0/24 are poor choices for the local network, as VPNs are based on IP routing and IP routing gets tangled when the same subnet is used on both ends of the VPN. 192.168.0.0/24 and 192.168.1.0/24 are near ubiquitous in home networks and coffee shops.

C6180 how to enable web services

Hi
c6180 w7 64 bit
Trying to set up HP eprint home&biz on ipad3
1.how do you enable web services
2.when trying to map network drive, computer can't find the "Folder" address i enter, taken from the eprint " saved files" display on the ipad
Thanks

Hello there again, hope you are doing well;
Let's start by Uninstalling any HP All-in-One software.
I will problaby do this in safe mode to ensure that no drivers or proccesses are in use at the time that you are installing the printer.
On the Windows taskbar, click the Windows icon ( ), click Control Panel , and then double-click Programs and Features .
Click the following HP software components, click Uninstall near the top of the window, and then click Next to uninstall the software.
HP Deskjet/Photosmart/All-in-One software
HP Imaging device functions
HP Customer Participation program
HP Solution Center
HP Photosmart Essentials
I will prefer for you to use this Tool to reinstall the printer CLICK HERE.
Before continuing I will  suggest you to disable all security applications (including Windows firewall ) to eliminate the some component of the software being quarantine or block. after disabling all security applications,
See if the problem is solved. if not continue.
Change the DNS server to Google's public DNS which is 8.8.8.8 and 8.8.4.4 for the secondary or alternate DNS (second DNS server) does your printer have an static IP address. If not let's set that as well, uninstall and reinstall the printer,  by the way this is the main support page for your printer if you need it for future reference GO HERE
Let's print a Network configuration page,
Press the Setup button ( ) on the front of the product.
Press the Down Arrow button ( ) to highlight Network , and then press OK .
Press the Down Arrow button ( ) to highlight Wireless Network Test , and then press OK .The Wireless Network Test Report prints.
On the test page, find the IP address.
Example IP address on the network configuration page;
If the product IP address on the test page is 0.0.0.0 or 169.254. XXX. XXX , this means that the HP product is not connected to the network. Continue to the next step to set up the product on the wireless network. If the product IP address on the test page is not 0.0.0.0 or 169.254. XXX. XXX (for example, 192.168.0.5), this means that the HP product is connected to the network. Review the steps in this document to check communication between the product and the computer.
The 169.254.xxx.xxx is use for APIPA  Automatic Private IP Addressing and is self assing if you have one of this you will need to disable IPv4 and enable it to see if there only a glick is that does not fix the problem if may be corruction on the stack of protocols you will have to uninstall and reinstall the protocols stack. Refer to the Operating system KB to see how you accomplish this.
Let's set the static IP first,
In the EWS screen, click the Network tab.
Click Wired (802.3) , and then click the IPv4 Configuration or the IPv6 Configuration tab.
Click Manual IP . The Manual IP Address box opens.
In the Manual IP Address box, type an IP address with the same values in the first three sets of digits (subnet values) as the product's IP address (listed on the Network Configuration Page), and a higher value (between 1 and 254) in the fourth set of digits. This creates a static IP address on the same subnet, but outside the Dynamic Host Configuration Protocol (DHCP) range.
For example, if the product's original IP address is 192.168.0.1 , assign the static IP address to 192.168.0.200 .
Figure 5: Example of an IP address - DHCP values shown
Figure 6: Example of a static IP address with DHCP values modified
NOTE:Do not type the static IP address from the example. Enter a static IP address based on the IP address for your product.
Enter the Subnet Mask and the Default Gateway settings as they appear on the Network Configuration Page.
Now here should be able to set the DNS server to the google's Public ones, Please. Do so
Click OK to save the new settings, and then click Exit or close the browser to exit the EWS.
Let me know if this helps and will continue making my best effort to assist you until we get this working properly
Hope this helps and regards;
RobertoR
And remember. . .
You can say THANKS by clicking the KUDOS STAR. If my suggestion resolves your issue Mark as a "SOLUTION" this way others can benefit Thanks in Advance!

How to create web service for database application

Hi everyone
Is it possible to create a web service for an apex database application page which has reports and radio fields and dialog boxes and validations in it. IF it is possible to create, pls help me with example or step by step procedure. I have seen all oracle docs of implementation of Web services in apex but unable to figure out how to get that link of wsdl for an application.
Thanks in advance.
Regards
Sandeep Artham

Hi,
I guess there are other ways. But this is an easy way, if you find the right wizards.
Besides this it is good practise to define interface methods so that session bean implement these interface methods, and thus seperate the interface from the implementation.
In this approach you will need 3 projects:
An enterprise application project (will contain EJB Module)
An EJB Module project (will contain session bean)
A Java project (contains code that implements the session bean methods)
In my previous post I suggested to use a J2EE web mudule project. This was a mistake, it should be EJB module.
But it should be possible to do it in another way. It is up to you.
Good luck, Roelof

How to generate web services for OAS with wsdl extension

Hi,
I wanted to know how to generate web services from Oracle Application Server especially with .wsdl extension and with document/literal style.
I know that earlier there was a tool called SmartConnect from BEA WebLogic.
But that will work only with ALSB (Aqua logic Service Bus). I guess that ALSB has been renamed as Oracle Service Bus by Oracle after the acquisition of WebLogic. My question is what is the new name for the SmartConnect Tool from WebLogic, which generates wsdl very easily from Oracle database.
I am unable to know the new name for SmartConnect and how to download that tool from Oracle web site.
Also, I want to know, whether there is any other way to generate the wsdl from Oracle, if so, please let me know.
Regards
Raman

Hi Jeethandra,
Please refere to the below link might be some help.
[http://help.sap.com/saphelp_mdmgds55/helpdata/en/45/069152856241e1e10000000a1553f6/frameset.htm]
regards
shankar

How to create web service for a Java class in SAP NetWeaver Studio

hi all,
i am using SAP Netweaver Developer Studio.have created a normal java project and i want to create web service for one of the classes in this project. i used the Web Service Creation Wizard to create a web service for this class. but it says there's no methods available for VI. all my methods in this class are public, what should i do?

Hi,
I guess there are other ways. But this is an easy way, if you find the right wizards.
Besides this it is good practise to define interface methods so that session bean implement these interface methods, and thus seperate the interface from the implementation.
In this approach you will need 3 projects:
An enterprise application project (will contain EJB Module)
An EJB Module project (will contain session bean)
A Java project (contains code that implements the session bean methods)
In my previous post I suggested to use a J2EE web mudule project. This was a mistake, it should be EJB module.
But it should be possible to do it in another way. It is up to you.
Good luck, Roelof

How to create a service for the OHS (Apache 2.0) on Windows?

I've downloaded the Oracle HTTP Server (Apache 2.0) (10.1.3.3.0).
It works also fine with DB 10gR2 and APEX.
But how do I create a windows service for the opmnctl.exe?
Thanks
Ralph

I've downloaded the Oracle HTTP Server (Apache 2.0) (10.1.3.3.0).
It works also fine with DB 10gR2 and APEX.
But how do I create a windows service for the opmnctl.exe?
Thanks
Ralph

How to Enable Remote services using the GPO for the Client Machines

How to enable remote Access services on Client machines using the Group Policy. After enable how to access with out switching the users remote as administrator

Hi,
If you use windows server 2003, we can refer to the following link to enable remote access services on Client machines using the Group Policy:
Enable or disable Remote Desktop
http://technet.microsoft.com/en-us/library/cc727977(v=WS.10).aspx
If you use windows server 2008 and later version, we can refer to the following link to enable remote access services on Client machines using the Group Policy:
How to Enable or Disable Remote Desktop via Group Policy Windows 2008
http://social.technet.microsoft.com/wiki/contents/articles/4980.how-to-enable-or-disable-remote-desktop-via-group-policy-windows-2008.aspx
After you enable
Allow users to connect remotely using Remote Desktop Services policy setting, users who are members of the Remote Desktop Users group on the target computer can connect remotely to the target computer by using Remote Desktop Services.
So if you want users to access computer remotely, you need add users as members of the Remote Desktop Users group on the target computer.
About how to add users to the Remote Desktop Users group, please refer to the following link:
Configure the Remote Desktop Users Group
http://technet.microsoft.com/en-us/library/cc743161.aspx
Best Regards,
Erin

How to generate web services for MDM Taxanomy Tables?

Hi Experts,
I have a Taxonomy table called eClass in material repository which contains the Hierarchical data. The data[Attributes of this table ] can be seen only in Taxonomy Mode, I want to generate the web service using MDM Web Service Generator. The service should perform the CRUD operation over this table and retrieve the attributes. I generated the service for this table but I am not able to retrieve the attributes. Please help me out for this situations. Any pointers regarding this will be appreciated.
Thanks & Regards
Jeetendra

Hi Jeethandra,
Please refere to the below link might be some help.
[http://help.sap.com/saphelp_mdmgds55/helpdata/en/45/069152856241e1e10000000a1553f6/frameset.htm]
regards
shankar

I cant enable web services on the printer

office jet pro 8600 plus
syst window 7

Hello,
The first thing I would do is follow step six in this document to set a static IP: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02817031&cc=us&dlc=en&lc=en&product=4023246&tmp...
When it askes for DNS information, enter in Google's DNS. Preferred DNS = 8.8.8.8 Alt DNS = 8.8.4.4
If that does not help, if you could provide me with the following information it would help me out. First, who is your ISP( Internet Service Provider, i.e. Comcast, AT&T, Verizon, ect.)? Second, who is the maker of your router? Lastly, what is the model number and firmware version of your router?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

How to creat web service for a function module?

who can provide me some resource on the topic.
thanks
Johnney.

Hi John,
http://help.sap.com/saphelp_nw04/helpdata/en/e9/ae1b9a5d2cef4ea4b579f19d902871/content.htm
Reward Points if Useful
All the Best
Gokul

How to Remove & Re-Enable Web Services on LaserJet printers supporting ePrint

If your LaserJet printer has been disconnected from or failed to connect to Web Services, you may need to power cycle your printer to reconnect. If that does not resolve the problem, you can remove web services, wait 30 seconds, then re-enable web services to re-establish your connection to ePrint and Print Apps. Note: this last step will result in a new email address being assigned to your printer.
How do I remove HP Web Services for my LaserJet printer?
Print a configuration page from your product, and locate the IP address.
At your computer, open a Web browser and type the product IP address into the address line and press Enter. The HP Embedded Web Server opens.
Click the HP Web Services tab.
Select the option to disable Web Services.
How do I enable or re-enable HP Web Services for my LaserJet printer?
To use HP ePrint, you must first enable HP Web Services. Re-Enabling Web Services uses the same procedure as enabling the Web Services.
Print a configuration page from your product, and locate the IP address.
At your computer, open a Web browser and type the product IP address into the address line and press Enter. The HP Embedded Web Server opens.
Click the HP Web Services tab.
Select the option to enable Web Services.
When Web Services are enabled, ePrint information appears in the HP Embedded Web Server. Look for the e-mail address that is automatically assigned to the product. The product also prints an HP Web Services information sheet that contains this e-mail address and instructions
If you were unable to register your printer in www.hpeprintcenter.com within 24 hours of printing your information sheet, you must re-enable the printer code by reprinting your information sheet. The information sheet will also provide your email address if you have forgotten it.
How do I print the Web Services Information Sheet for my LaserJet printer?
You can only add the printer to your HP ePrintCenter account within 24 hours after printing the information sheet. You can re-print the information sheet at any time from the printer control panel.
Print a configuration page from your product, and locate the IP address.
At your computer, open a Web browser and type the product IP address into the address line. The HP Embedded Web Server opens.
Click the HP Web Services tab.
Click the Print Information Sheet button.
I am an HP employee.

To help improve the organization and information sharing in this forum this post/discussion has been closed and replaced.
Please see this post: <link to new “Enable Disable Web Services on your printer” post.
If after reviewing the post above you still have questions/issues with your web-connected printer, you can either review and comment in existing posts in this forum that report issues like yours, or if necessary start a new post requesting assistance.
Miles
HP Employee

How to enable web services for the HP envy 4500

Similar Messages

Maybe you are looking for