How to enter into interface configuration mode on aironet 1130AG

How can I enter into "interface configuration" on Aironet 1130AG, AIR-LAP1042N?
When I put following commands in enable
conf t
interface Dot11Radio1
but, it fails and I cannot enter into "interface configuration".
How can I do this ?
The reason why I enter into
conf t
interface Dot11Radio1
because I want to disable cdp via CLI ( serial console).
best regards

George,
I ran into an exception the other day – lightweight 3500s (and presumably 3600s) are allowing config t without the debug precursor. The lab version I’m doing this on is 7.0.220.0. Do you have same/different results? I’m not sure if this is tied to the AP model or the lw code they’re running. I’ll need to do some more testing.
Justin

Similar Messages

How to enter into sap

thnkq sir.i started to learn.In ecc6 I am unable to enter into sap
I ma giving Client 000 User as a DDIC and Password 19920706.How to enter into sap. Can any one give me any tips?
thnq

Hi,
Are you using IDES of ECC6? if yes, you can use client 800. in this IDES model data are there.
is there any other user in the system.. if yes then create one user for yourself by them.
in ECC6 IDES, you can login with DDIC in 800 client with password 19920706
For IDES
"In the clients 000/001 you can logon with DDIC and SAP* with the password you have defined at the beginning of the installation as 'Master-Password', in the clients 8xx with the password 19920706 / 06071992 and in all clients
with IDADMIN / ides"
read this note
https://service.sap.com/sap/support/notes/1244548
Regards,
Debasis.
Edited by: Debasis Sahoo on Oct 18, 2008 12:47 PM

How to enter into shared services in system 9

how to login into shared services

Hello,
I'm new with Hyperion and would like to ask something. I installed Hyperion Shared Services 9.3.1 in my desktop (inside consist of Windows XP Professional Service Pack 3, 1 GB RAM, Oracle Database 10g (10.2.0.1) Standard Edition, Oracle Application Server 10g).
I read from Hyperion Shared Services security guide in Chapter 3 about User Management Console that we can launch User Management Console in 3 ways:
1. Using a browser and connecting to the User Management Console URL
2. On Windows, navigating Start > All Programs > Hyperion > Foundation Services > User Management Console
3. From a Hyperion product interface
I tried to connect using URL : http://<localhost>/58080/interop and http://<localhost>/58080/interop/ and http://<localhost>/58080/interop/index.jsp but failed (where I changed <localhost> to my computer name). When I installed Shared Services, there are no point to choose port or create username.
There are no User Management Console in Foundation Services either.
How to start and stop Shared Services then and how do I know Shared Services has already run?
Thanks.

How to get into iPod Diagnostic Mode

I followed someones advice to get into Diagnostic Mode...duplicated below.
Problem is after rebooting iPod and the apple logo appears the button combination didn't work to get into Diag Mode for my iPod. Anyone know the combination for a 15GB docking (touch wheel) iPod????
Instructions provided on forum:
1)Maybe you have damaged hard drive, you can check that by running a HDD Scan.
2)To do that you need to get into diagnostic mode.
§First reset the iPod
§How to reset iPod:
1.Connect iPod to the iPod Power Adapter and plug the power adapter into an electrical outlet.
2.Toggle the Hold switch on and off. (Slide it to Hold, then turn it off again.)About 4 times, when you are finished make sure it is not on hold.
3.Press and hold the Menu and Select buttons (select is the middle button) until the Apple logo appears, about 6 to 10 seconds. You may need to repeat this tep.There are two small pins within the iPod that need to make a connection to reset the iPod the pressure has to be just right. Sometimes it is easier to do this if you put the iPod on a flat surface.
§Then as soon as you see the apple come up on the screen, change to pressing select and the previous arrows (the arrows that are pointing to the left).
§The screen will change it will say IRAM PASS, DIAG VER.
§PRESS PLAY TO CONTINUE.
§Press play to continue and then using the advance arrows, (arrows that point to the right), scroll down to the HDD SCAN and press select.
§It should take anywhere from 45 mins to around 2 hours for the scan to run.
§The scan will tell you exactly if your hard drive is damaged. This also can have effect on your battery life.

Actually, there's nothing you can do in Diagnostic Mode to create a problem, you can only check for them
Nope. HARD R/W will do a test of both writing and reading of the hard drive. This test is destructive, your data will be lost. There's also the CLEAR BLKS test and the HDD DROP test.
Not to mention that the scanning processes exercise the hard drive quite a bit, and frankly the iPod drive isn't made to stand that kind of abuse for very long.
In any case, there's realistically nothing you can test in diag mode that you can't test in other ways. A simple format will check the drive for sector errors (along with erasing it). There's very little point to using the diag mode.

Does not enter into automatic sleep mode + win 8

I can manually put my Windows 8 PC to sleep, but when the program goes into sleep mode the monitor shuts down but PC keeps running.for this i run powercfg.exe /energy and it will show me these errors.
Requesting Process\Device\HarddiskVolume5\Program Files (x86)\Internet Explorer\iexplore.exe
Requesting Driver Device
Realtek High Definition Audio
when i check in device manager for power option in Realtek High Definition Audio property i also cant find that
plz suggest me a reliable solution for the same
thanks

Hi,
As Milos said, first thing we would do is see if all my hardware drivers are up to date. The Windows drivers are the best match for most hardware but you may have better results with drivers obtained directly from manufacturers.
Meanwhile, please try installing the latest version driver for Realtek High Definition Audio to test it.
Regards,
Kelvin hsu
TechNet Community Support

How to get into CRISIS RECOVERY mode to reflash BIOS?

Hi..
I have a ProBook 4710s andmy BIOS is bricked, blank screen with flashing capslock, which means Authentication BIOS (failed).
And I can't find the key combinations to put my notebook into the crisis recovery mode to reflash the BIOS.
Does anybody know the combination??? (I've tried <Win>+ , <Func>+, <Win>+<Esc>, <Func>+<Esc>... and nothing)
HELP!!!! PLEASE!!!

I found the document confirming this, see bios authentication failure on this page
http://h10025.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=us&docname=c01443366#N1231

Unable to enter into recovery/DFU mode for updating software

Hi, I bought a new iPhone 4 yesterday and while i was playing with it, I noticed that whenever I opened the camera app the phone crashes. I called apple and they told me to update the software.
When I connected it to itunes and tried to update, it gave me a random error (which i don't remember). I disconnected the phone and tried to reset the "Erase All Content and Settings" from the settings app itself but it was taking a very very long time. So i connected it to the computer again and now it has been stuck on the boot screen for about 2 hours. If i hit the sleep/wake button and the home button together and hold it down it goes into the recovery screen for about 2-3 seconds and then immediately quits and goes back to the boot screen, if i keep holding the two buttons this cycle continues but it never stays on the recovery screen for more than a second or two and hence I am unable to recover my phone.
I don't know what to do, please advise.
Thanks

Make a genius appt at an Apple store
http://www.apple.com/retail/geniusbar/
and let them deal with it.
Phil

How to enter BIOS crisis recovery mode on x120e?

What combination of keys must be pressed? Fn+F? Fn+B? Other?

Hi provaleriy,
simply hit F1, after pressing power button or while watching the Lenovo boot screen.
Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
Please insert your type, model (not S/N) number and used OS in your posts.
I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
English Community Deutsche Community Comunidad en Español

Global Configuration Mode (Aironet 2600i)

Hello to all,
It's my first time in the forum, I thank any help possible. I bought a Cisco Wireless AIR-CAP2602i-E-K9 and have some practice on Cisco routers, but can not log in "Global Configuration Mode", not existe the command "Configure". How active configuration? Thank you for your attention.
Helio Viegas

Hello Helio,
As per your query i can suggest you the following solution-
Cisco IOS Command Modes
The Cisco IOS user interface is divided into many different modes. The commands available to you depend on which mode you are currently in. Enter a question mark (?) at the system prompt to obtain a list of commands available for each command mode.
When you start a session on the access point, you begin in user mode, often called user EXEC mode. Only a limited subset of the commands are available in user EXEC mode. For example, most of the user EXEC commands are one-time commands, such as show commands, which show the current configuration status, and clear commands, which clear counters or interfaces. The user EXEC commands are not saved when the access point reboots.
To have access to all commands, you must enter privileged EXEC mode. Normally, you must enter a password to enter privileged EXEC mode. From this mode, you must enter privileged EXEC mode before you can enter the global configuration mode.
Using the configuration modes (global, interface, and line), you can make changes to the running configuration. If you save the configuration, these commands are stored and used when the access point reboots. To access the various configuration modes, you must start at global configuration mode. From global configuration mode, you can enter interface configuration mode and line configuration mode.
For more information please refer to the link-
http://www.cisco.com/en/US/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15cli.html
Hope this will help you.

Active/Standby And failover link configuration mode

Hi everyone,
When config failover link of ASA in Active Standby mode.
When we config failover int say gi0/1
config t
int gi0/1
failover lan int gi0/1
Need to confirm we do this from interface config mode only or we can do this from global config also ????????
Whe we assign IP to this int we do that from global config mode ????
Regards
Mahesh
Message was edited by: mahesh parmar
Message was edited by: mahesh parmar

Hi,
Actually the ASA lets you insert a lot of command what ever mode you are under.
In the output you posted is a very important thing to notice
configure mode commands/options:
WORD Specify the interface name
As you can see, the output lists only one option and before that it mentions that this is a "configure mode" command
So even if you entered the command under the interface configuration mode, it would still be entered as a global/configure command mode.
Take the following thing for example
I want to check what configuration options I have with the command "failover"
So I enter the following to my ASA
ASA(config)# failover ?
configure mode commands/options:
interface              Configure the IP address to be used for failover and/or
                              stateful update information
interface-policy    Set the policy for failover due to interface failures
key                       Configure the failover shared secret or key
lan                       Specify the unit as primary or secondary or configure the
                               interface and vlan to be used for failover communication
mac                      Specify the virtual mac address for a dynamic interface
polltime                Configure failover poll interval
timeout                 Specify the failover reconnect timeout value for
                               asymmetrically routed sessions
exec mode commands/options:
active          Make this system to be the active unit of the failover pair
exec            Execute command on the designated unit
reload-standby Force standby unit to reboot
reset           Force a unit or failover group to an unfailed state
As you can see, the ASA tells us that there are different additional command parameters after the "failover" command that can be used. Some of them can be used either in Exec or Configuration mode.
- Jouni

Cisco CSS11501 - Interface Configuration

Is it possible to configure the port speed and duplex on the ethernet interfaces? If so, how would I do it?

In interface configuration mode, use the 'phy' setting.
CSS(config-if[ 2/2])# phy ?
100Mbits-FD 10/100 ports only. Set to 100 Mbits/s, Full-Duplex
100Mbits-HD 10/100 ports only. Set to 100 Mbits/s, Half-Duplex
10Mbits-FD 10/100 ports only. Set to 10 Mbits/s, Full-Duplex
10Mbits-HD 10/100 ports only. Set to 10 Mbits/s, Half-Duplex
1Gbits-FD-asym Gigabit ports only. Set to Full duplex with asymmetric
pause toward link partner
1Gbits-FD-no-pause Gigabit ports only. Set to Full duplex with no pause
1Gbits-FD-sym Gigabit ports only. Set to Full duplex with symmetric
pause
1Gbits-FD-sym-asym Gigabit ports only. Set to Full duplex with symmetric and
asymmetric pause toward local device
auto-negotiate Allow the interface to auto-negotiate speed and duplex
mode.

How do I mount an external Firewire HD when booting into single user mode?

Hi,
How can I mount an external Firewire Harddisk from the Darwin Console, once I have booted into single user mode?
I'm trying to make a backup of all my files and then re-install my iMac G5 since it doesn't start the GUI anymore and I haven't gotten any responses to my question here: http://discussions.apple.com/thread.jspa?threadID=1104762&tstart=0
Thanks,
Torsten

ok, I executed the following commands:
/sbin/fsck -fy
/usr/libexec/registermach_bootstrapservers /etc/mach_init.d
autodiskmount
There were two messages:
UniNEnet: Ethernet address 00:14:51:32:19:b8
and
Aug 29 20:55:29 launchd: server 2e3b in bootstrap 1103 uid 0: "/usr/sbin/lookupd"[16]: exited abnormally: Hangup
I don't know whether this has anything to do with the commands I entered.
And since I don't know what the volume name for the external Firewire HD is, I typed
ls -l /Volumes
but the only volume that is being listed there is my iMac's internal HD.
What should I do next?
Thx!

How to enter Enhancement Mode of ABAP OO Classes: Add Methods, Pre-Methods.

Hello,
do you know how to enter the enhancement mode of the class builder?
I want to enhance a standard global ABAP OO class by implicit enhancements for inserting methods, attributes or pre- and post-methods - as described in <a href="http://help.sap.com/saphelp_nw70/helpdata/en/58/4fb541d3d52d31e10000000a155106/content.htm">Online help</a>.
I start the SE24 on my NW 7.0, but there is no menu Edit-> Enhancement Operations-> Enhance Class/Interface as written in <a href="http://help.sap.com/saphelp_nw70/helpdata/en/86/b83142680d5c33e10000000a155106/content.htm">Online Help</a>.
When I press the Display button, there is no enhancement button (the spiral), and the sub entries of menu Edit-> Enhancement Operations, like Insert Pre-Method are inactive (gray).
In SE80 I don't find them too. The only implicit enhancements I found are on the beginning and end of methods implementation code.
Do you have experience enhancing classes?
Best regards
Michael Umlauff

Hallo Michael,
You first have to go in se80 or se24
Then menu Class-> Enhance
Then you will be able to use Edit-> Enhancement Operations-> Insert Pre-Post Methodes
Regards,
Walter

How to write table values into a configuration file

Im writing some values in the table, i want to save and load the table values, how to save the table configuration into configuration file??

Pls ignore my prev post, I cud not finish edit within 10 mins as req by the forum rule...
If you are not able to access a VI front panel at all when another VI is called by the first VI, then probably the issue is that the VI properties is set to be Modal. Right click on the VI icon on the right top corner and select VI Properties. Under Window Appearance, you can click on Customise button and ensure the VI is not Modal (and Custom is selected). Before this, you need to ensure the calling VIs are also not set to Modal (I think if you set it to dialog, it will be Modal by def. So don't use that as well). If any of the parent VI is set to Modal and a subsequent child VI is in non-modal mode, then you will not be able to access the child VI front panel when called and may end up with forcing the program to close.
Probably you may also need to have a different independant loop looking for the events. For this you may need to use Q structure as well, so that you can define a Q outside both loops, add elements to Q as and when the menu is selected within the loop for menu events, while the other loop works according to the Q elements it gets to remove.
Hope that helps !

How can I delete a page I've entered into a Dashboard Window

How can I delete a page I've entered into a Dashboard Window?

If by "page" you mean a Dashboard Widget, then it's simple:
Open Dashboard (F4 on my keyboard) and in the lower left corner you'll see a cross in a circle. Clicking it enables add/delete mode and all possible adds show up at the bottom of the screen while all currently added Widgets stay where they are but get an X in a circle attached to them. Clicking on the X deletes the Widget.
hope this helps

How to enter into interface configuration mode on aironet 1130AG

Similar Messages

Maybe you are looking for