How to extend wireless with airport express and time capsule

So, I have a time capsule & because of the thick walls in my apartment, I can barely use my ipad and iphone at night in my bedroom! (my macbookPRO stays at 3 bars however!)
I bought an airport express thinking I could plug it closer to or inside my bedroom to boost the signal - but it doesn't seem to work that way - any tips on how to set this up?
TWO ADDITIONAL Qs:
Does connecting directly to my time capsule (which i'm assuming i'd need another ethernet cable) help with the boost? (then negates the other great uses for the airport express it seems)
Isn't there a way to do the boost with the express wirelessly? I'd really love to get wireless speakers, use airplay AND be able to use my devices just two rooms away .... HELP!
thanks so much (when did apple phone support start to be closed on Sundays?)
cheers.

Suggest that you check your setup again to make sure that the settings are correct on both the Time Capsule and AirPort Express.
Open AirPort Utility, select the Time Capsule and click Manual Setup
Click the Wireless tab below the row of icons
Make sure that a check mark is entered next to "Allow this network to be extended".( If the box is not checked, the Time Capsule will not extend to the AirPort Express)
Click Update to save your settings and close AirPort Utility
Next, open AirPort Utility again, select the AirPort Express and click Manual Setup
Click the Wireless tab
Settings should look like this:
Wireless Mode = Extend a wireless network
Wireless Network Name = Same name as the Time Capsule network
Check mark entered next to "Allow wireless clients"
Wireless Security = Same setting as the Time Capsule
Wireless Password = Same password as the Time Capsule network
Confirm Password
Update to save settings and close AirPort Utility
Locate the AirPort Express approximately half way between the Time Capsule and area that needs more wireless coverage. You may need to experiment on placement to find the best compomise.
Post back on your results.

Similar Messages

Best way to extend wireless via airport express and time capsule

best way to extend wireless via airport express and time capsule
i live in a two storey house where i use my airport express to create a wireless network in the main floor, and time capsule to extend it in the upper floor, where my room is. i have like 16 mbps in the main floor, and 2-3 mbps in the upper floor after having speediest.
i used time capsule in the upper floor because i use wireless backup daily and don't want to put internet down while i im doin it and consequently my parent can have internet access in the main floor, am i right? or do i have make just the opposite in order to have a good internet speed?
secondly, while checking airport express wireless mode on airport utility, there is like 4 different type of radio mode(802 11n bg comp, 802 11n 2.4, 802 11n a comp, 802 11n 5ghz) which i have no idea what they mean
what do you recommend?
we have like iphone4, iphone 3g, mbookpro, ipad, ipad 2, samsung tv and a sony vaio laptop in the wireless network
thank you

What you have would appear to be working but I can comment how I would redefine your setup. Note that both Airport Express and Time Capsule can function as wireless base stations so you do have wireless everywhere and at all times — using the Time Capsules for backups doesn’t mean your parents won’t have internet access regardless of the where the base stations are located.
You appear to have devices to connect to your network that use the 2.4 GHz band with 802.11g such as the iPhone 3G and perhaps the 5 GHz band with 802.11n such as likely the Macbook Pro if it’s a recent model. The iPhone 4 can use 5 GHz and 802.11n. Can’t comment on the Sony and Samsung but you can check their specs.
Now the Time Capsule (if it’s a recent version), can simultaneously supply 2.4 GHz and 5 GHz band signals, but the Airport Express (if it’s recent) can only use one of those bands at one time. Likely the lowest common denominator for your devices is going to be the 2.4 GHz band since the devices that are capable of using 5 GHZ also support 2.4 GHz. If you don’t use 5 GHz, you won’t lose much in a two-storey home because likely it’s the 2.4 GHz band is better signal anyway because 5 GHz signals drop off quickly with several walls/floors to penetrate.
You also didn’t mention if the Airport Express is used to support a printer and/or AirPlay (using iTunes to play on remote speakers via the Airport Express connection) but that might also be a factor in the best location to place the Airport Express. Although the printer could be switched between the Time Capsule and the Airport Express if needed, only the Airport Express will support your remote speakers.
Recommend you use the Time Capsule as the Base station. When using Airport Utility to define the network, after you name your network, etc., select the Wireless tab, check the box “Allow this network to be extended” and set the Radio Mode to "802.11n (802.11b/g compatible)”.
Using the Airport Utility, click on the Airport Express; after you define the device and network name, select the Wireless tab, define the Wireless Mode as “Extend a Wireless Network” and check the box “Allow wireless clients”.
Hope that helps.

Extending wifi with airport express and time capsule

Hi All
I'm new to macs and moving over in a big way!
I started with a time capsule and all was fine apart from the coverage in the house.
It seemed easy to extend the wifi so purchased an AE 802.11n and extended the network.
It does extend and I can connect to the internet but the network is now really really slow and the time capsule backup wont work.
connection is :
Ethernet modem - Airport express ( as its close to my audio equipment ) - extended WIFI conection via 802.11n.
Any suggestions? why is it so slow?
Im at 7.3.1 firmware on both AE and time capsule and the Macbook pro is at 10.5.3.
Any suggestions?

I've managed to change the 5gHz of ther Airport Express that's extending the network.
As mentioned, main AE is on channel 48, and I now have the 2nd AE on channel 36 - which means my TV can now see the network. Also tested speed via my mavbook air on the same 5gHz network as it all seems OK (A while ago I spotted my Time Capsule was on the same channel 48 as main AE and throughput was abysmal! Bad enough to make me reset the TC to factory defaults and setup again - which is when the TC got channel 120).
Anyway, the fix... I changed the 2nd AE to create a wireless network (instead of extend), and manually set the channel to 36. I then set it back to extend, and it seems to have kept channel 36.

Conflicts with Airport Express and Time Capsule

I am using Airport Express and Time Capsule at the same time. Connection to the web is via a router. Very often I do have conflicts. How shall I connect the gadgets? At the moment I connect the router to Airport Express (network cable).
Time machine back up doesn't work properly.
Is there anybody able to help me?
Regards

What broadband type do you have?
It can be impossible to plug a TC into the existing connection because the virgin media router has special setup or logins which are not revealed to end users.
If it is a fibre connection for instance the TC may simply not work. They have issues with many fibre ISP putting the gateway address outside the subnet of the main public IP.. (don't worry if it is too technical .. it amounts to .. it don't work! )
You may need to wait until Sat.
Get in a big supply of home videos or something and try and starve off your addiction.

Sharing an internet connection with Airport express and Time Capsule

Hi, I have been happily using a cable modem and a Time Capsule for my internet connection and wireless network. We recently added solar panels to our roof and the system needs to be connected to the internet so it can be monitored remotely. Calling Comcast is an exercise in frustration, and the solar people don't seem to know exactly how to do it, so I'm trying this.
We bought an Airport Express, thinking if it is connected with an ethernet cable to the solar system, it could somehow share the internet connection with the Time Capsule, or they could talk to each other. When I plug in the Airport Express, the only set-up option seems to be to set up a new network, which I don't think I want to do. Can anyone tell me how to set this up? Thank you!

Hi, Under Water.
You should configure the Express to "Join a wireless network" or to "Extend a wireless network". (Either one will work.)
Connect your computer to your Express via Ethernet and open AirPort Utility. Press "Manual Setup" and authenticate if necessary.
Go to the "Base Station" tab. Give the Express a name and password.
Go to the "Wireless" tab. Set the Wireless mode to "Join a wireless network" or "Extend a wireless network." Enter the name of the wireless network created by your Time Capsule (or select it from the list). Check the box that says "Allow Ethernet clients" (if you're joining) or "Allow Wireless Clients" (if you're extending).
Provide the appropriate security mode and password for the Time Capsule's network.
Press "Update" and allow your Express to restart.
Then you can plug the solar system into the Express's Ethernet port.

Extending network with Airport Express from Time Capsule Base Station

I have a working Time Capsule wireless base station that's setup and working successfully. I want to extend my network and connect to my stereo for playing via iTunes. I've spent hours trying to get the Airport Express to connect.
What's the correct basic approach? Time Capsule base and adding the AE to the network? Setting up WDS? If anyone has the proper settings for both the TC and the AE I would be very appreciative.

I still say this needs to be addressed by Apple on why there isn't 2 different forums for the old Express or the new Express.... Just like the Extreme Base Station. A lot of time is wasted on the forum on which Express a person has.....
1. Old Express with "g" ????
2. New Express with "n" ????
If you have the old Express, you need to set it up using WDS along with the TC.
If you have a new Express, then you can just check the TC settings for "allow this network to be extended" and set the Express to extend the network. This is much easier than setting up a WDS.
Good Luck
Joseph Kriz

Error 6742 with AirPort Express and Time Capsule

Hi all,
I have an AirPort Express from 2009 and a Time Capsule from 2010. I always use my Time Capsule to join to my existing network and stream my external hard drive across my house.
Yesterday our IP router died (Virgin Media) and we are not getting a new one until Saturday the earliest... So I thought oooo I have an Airport Express spare and a Time Capsule we could use.
However when I try to connect both of them to the modem all I get is error 6742. When I have searched for this people are suggesting the hardware has died, well my Time Capsule was definitely alive and well when I tried to set it up against the modem as it was streaming my external drive. My Express, well maybe, it has been in a cupboard for a few years...
Does anyone have any ideas what I could do to set this up? I have tried a reset and a factory reset on both units.
Thanks

What broadband type do you have?
It can be impossible to plug a TC into the existing connection because the virgin media router has special setup or logins which are not revealed to end users.
If it is a fibre connection for instance the TC may simply not work. They have issues with many fibre ISP putting the gateway address outside the subnet of the main public IP.. (don't worry if it is too technical .. it amounts to .. it don't work! )
You may need to wait until Sat.
Get in a big supply of home videos or something and try and starve off your addiction.

How do I use my airport express or time capsule to increase the signal strength of my comcast router

How do I use my airport express and/ or time capsule to increase the range of my newly installed comcast modem/router.

Neophite50 wrote:
Thanks.
A question. Do I plug the TC into the Comcast modeum Router or the iMac?
Both is good.. but at least one of your routers.. TC or express must be plugged into the router.. the imac can get internet connection by wireless.

Cisco router RVS4000 with Airport extrem and Time capsule.

Problem droping connection to internet when is Time capsule in extended wifi mode. When I turn off wifi on time capsule Airport extreme work fine.
Airport extreme and Time capsule is conected via ETH.
Any idea ?
Thaks
B.

If you use ethernet to connect the AE and TC .. you must NOT extend wifi.. you use Create a wireless network. And setup with same name and security. You are using roaming network.. not extended wireless.. if you want to use extended wireless no ethernet
see http://support.apple.com/kb/HT4260

Trouble with Airport Extreme and Time Capsule

Just got a new 2TB time capsule and added it to my network (existing Airport Express and Airport Extreme). All devices are hard-wire back-hauled to Linksys router. Set up was straight forward with no issues and initiated a time capsule back up without a problem. Within hours I noticed that the TC was no longer reachable in Finder.. Opening the AirPort utility, I saw that both the Extreme and the TC were "lost". Still had (green) internet connectivity, but the base stations were showing as off-line in the Airport utility.
Tried rebooting and checking from multiple other devices and no luck. Occasionally will find them both on-line in Airport utility, but seem to lose one (usually TC) after a short period. All are running the most up to date version of firmware (7.7.3). Prior to installing the TC, I had experienced 0 issues with Airport Express and Extreme.
Has anyone else seen similar issues? Are there settings that need to be accounted for in some way to avoid these frustrating "lost devices"?
thanks

Thank you for your quick answer, smorkerz. However, I did it and it doesn't work.
I tried to check separately the time capsule and the airport extreme, switching one off when using the other one. The result is that each one works alone but when I use them both, just time capsule appears, works well, and I can't use the airport to print for instance.
Do you understand anything ?

Printing completely broken on both airport express and time capsule

Printing seems to be broken on both my old time capsul, generation one, and a new airport express. Here's what happens.
1. Connect printer directly to the Mac and everything prints fine.
2. Reconnect printer to the Airport or timecapsule. Delete all the printers. Power cycle everything. Add printer. Print and it keeps trying to connect to the printer forever.
It use to work and it may have been a recient firmware update that broke it. Any help would be appreciated. I've been through all of the support documents and still nothing. The printer is an old Epson Stylus R280. I'm running 10.9 with all the latest drivers and updates.

If you want to run a N speeds, run a cable from Time Capsule to Airport Express, set Time Capsule as your primary router, and turn off DHCP on Airport Express. This will create two networks, your Express will have one SSID, and the Time Capsule another SSID. One G network and one N network. Don't include the express in your network, keep it separate from Time Capsule to avoid it from coming down to G speeds. Make sense?

Extending network with Airport Express and Airport Extreme (latest models) causes chaos on network

Today I upgraded from my several year old Airport Extreme (3rd gen) and 2nd gen Airport Express to a new (what you'd buy on the shelf today) Airport Extreme and Airport Express. All airports are updated with the latest firmware and I'm using windows 7 for configuration.
The intention is to use the Airport Extreme as the main router, also serving wifi. And extend the network using the express. As such, the following has been done:
The Airport Extreme is configured for automatic channel, and automatic radio mode. I tried to select 802.11n 5 ghz and 802.11 n 2.4 ghz only, but it won't take the changes. Additionally, it wont' accept me using only channel 6. Not sure why, but I digress. The airport extreme is not set to broadcast a separate name for the 5ghz network.
The Airport Express is configured to use bridge mode, use an existing wireless network and is connected to my network on it's WAN port (the circle icon on the back) with ethernet. The password and wireless name used in configuration is the same as created initially on the Airport Extreme.
Initially I did the configuration of both airports on my computer, connected by ethernet to ensure stable connectivity while I inputted settings. During this, they appeared to accept the changes fine. However, when I moved the airport express to it's destination (other side of my house), the entire network went crazy.
Internet became slow, and often wouldn't load pages. This was on wired and wireless connections. When I attempted to administer the Airport in the Utility, they would not load, an error would occur. Also, at one point the Airport Extreme had renamed it self with a (2) at the end. Which was super odd. So far, the only solution has been to unplug the Airport Express and attempt to devise a solution.
Anyone have any ideas? Of course, I will continue to tinker with this, but it seems realllly strange. The previous setup was also extended (granted, using wireless only, not ethernet > wireless) and worked fine, granted it was a smidge slow, but it worked.

I wanted to add this.. I followed the guide here: http://support.apple.com/kb/HT4260 to extend using ethernet, and the above is the result.
I just tried re configuring in OS X Mavericks and got the same, odd, result.

Set up wireless with Airport Express and PC

i have ditched my cable/internet provider and use a service that brings the internet right to my apartment . I can access it with an ethernet cord. Airport Express was recommended even after I said I had a PC. I downloaded the airport utility. This where I am confused. I used one cord to plug the airport device to the wall where th internet comes in from. I used another ethernet cord between the AE device and my computer. i then went through the set up without a problem. When I unplug the cord between my computer and AE device my computer does not connect wirelessly. It does see other networks. When everything was plugged in i walked through the set up without any problems. Did I do something wrong with the cord set up?
Previously the computer had no problem with wireless access.

Typically when you get Internet from a wall socket there is either a modem or modem/router combination upstream of it that is providing the Internet service. In this case you will want to configure your AirPort Express as a bridge. Is this what you did?

How can I get my iTunes music on my wife's phone without hooking to my mac?i have iTunes Match I also have an airport express and time capsule hooked to a late 2012 imac.

Is there a way she can go through my library over the air with her phone and pick songs she wants and download them

So I would log out of iTunes on her account and log in on mine or is match have its own sign in?

Airport Express and Time Capsule

Hi
I am attempting to create the following setup and would like advice as to the best way to go about it:
In my house I have a Time Capsule connected to an incoming internet connection (from a cable modem) creating a WiFi network
I have a 'home office' at the end of the garden and have taken one ethernet output from the back of the TC and extended that to the office using a couple of TP Link Powerline adapters
The intention is to connect an Airport Express in the office connected to the TP Link adapter to create a WiFi network for the office
How should I set up the TC and AE to make this work? I have tried a few things using Airport Utility but no joy yet!
Many thanks in advance
PS Wasn't sure whether to post this here or in the AE discussion group so I have copied it there also.

First, please verify that the powerline adapters are functioning correctly by temporarily turning off the wireless on a computer and moving it to the office. Connect the computer to the Ethernet cable attached to the powerline adapter at that location.
See if you can get a good Internet connection that way. If you can, you know the powerline adapters are working correctly and the chances of an AirPort Express also working in the office improve.
Post back to confirm and we will continue with a detailed step by step setup of the AirPort Express.

How to extend wireless with airport express and time capsule

Similar Messages

Maybe you are looking for