How to find the Wireless LAN adaptor on my Satellite L350-21U

Today I received a message through Toshiba Tempro that an update for the LAN driver is available for my laptop which has Windows7.
However there are some possibilities i.e. INTEL, ATHEROS or REALTEK.
How can I find which LAN driver is installed on my laptop.
Please note that I am not so familiar with computers.
A step by step instruction would be appreciated !

Your notebook have Intel WLAN card but if the WLAN works well don't change anything.

Similar Messages

How to improve the wireless LAN coverage?

Hi all,
We are using Cisco 1200 access point in our small retail shops and use some wireless heldheld devices to connect the wireless network. Since the shops are inside the shopping plaza, there are many other wireless access point which interference our wireless clients. The access point were installed in the middle of the shop, sometimes, our client walked to the shop entrance (< 10m from the access point), the wireless network was disconnected and it may try to connect the other unknown access point. I tried to change the frequent but it doen't help. We are using a pair of 2.2dBi Dipole Anntenna wit the AP and mount in on the wall (~ 1m above the ground). Is there any suggestions to improve the coverage? Is there any improvement if I use a more powerful anntenna (e.g. 6.5 dBi Wall Mount anntenna)?
Thanks,
Dovelet

Dovelet,
I was going to suggest upgrading your AP to 802.11a but you are probably using Symbol handhelds and they don't support 802.11a yet (for that matter I don't think there is a handheld that supports 802.11a yet).
Use a computer and scan the airwaves to see what APs are out there and what frequency they are on. Configure your AP to a different channel either 1,6 or 11 (that no one else is on).
Put two 6 dBi Patch Wall Mount Antennnas 3 to 4 feet apart on one wall, part # AIR-ANT2460P-R. If you have a long narrow store the patch antennas will be your best bet, They have a narrow beam and you will get less multipath distortion from the radio waves bouncing off your walls. You can also get an Antenna mount kit, part # AIR-ACC2662 to help better aim your patch antennas.
If you have a square or circular store place two omnidirectional antennas in the center of the store, use a high grade low loss cable like part # AIR-CAB100ULL-R. Or for that matter put your current AP high in the center of the store. Run Cat5e cable to it and use a Power Injector to provide power to your AP over the cat5e. You can also add the high gain omnidirctional antennas (2 of them) to this configuration without needing the low loss cable.
These are powerful antennas and you don't want your signal going into the store across the way from you. So take a laptop or your hand held walk across the way to the front of the store and see what kind of signal you get. Reduce the power setting of your AP so the signal doesn't bleed into the store across the way from you and if you use omnidirectional antennas into stores on either side of you.
Make sure you mount the antennas high 8 to 10 feet. I assume you have your Encryption set,SSID broadcast disabled and your handhelds configured to only connect to your APs SSID.
Hope this helps.
Robert

How do I get my ipad to find the wireless HP printer that is supposed to be compatible w/ Air Print

How do I get my ipad to find the wireless HP printer that is supposed to be compatible w/ Air Print?

Mary-
First be sure your printer is on Apple's list of AirPrint compatible printers at <iOS: AirPrint 101>.
Assuming it is on that list, check to see if there is a firmware update for it. You should be able check it from the printer's control panel in one of the setup or preferences menus.
If the printer is still not found in the iPad's print routine, your WiFi router may not correctly handle Bonjour data required by AirPrint. You would need to contact the router's manufacturer to see if there is a change you can make to its setup, or if there is a firmware update that will solve the problem.
Fred

Re: Satellite L350-262 - The wireless connection adaptor is disabled

Basically my laptop is a couple of weeks old, it was working fine wirelessly until suddenly one day it stopped, it nows says The wireless connection adaptor is disabled, how can I resolve this? any suggestions?
Thanks

Can you please provide more details?
Can you see the WLan card in device manager?
Are there any yellow exclamation marks?
Does the other FN buttons work properly?
Is your BIOS up to date? Did you set it to default settings?
If not do this!
Last solution; try system recovery. This will set the notebook back to factory settings.

I have an ipad first generation. I am trying to connect to a linksys router and it is not finding the wireless network. what do i need to do?

I have an ipad first generation. I am trying to connect to a linksys router and the ipad is not finding the wireless network. What do I need to do? Thanks for your help.

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

I am in an internet cafe and my macbook pro can't find the wireless network available here. I have used this network before. I have restarted my machine several times too. help please

I am in an internet cafe and my macbook pro can't find the wireless network available at the cafe. I have used this network before. I have restarted my machine several times too. help please

Change your router channel. Sometimes this is all you will have to do.
Power cycling the router. Read the router's user manual or contact their tech support for instructions.
System Preferences/Internet & Network/Network
Unlock the padlock
Locations: Automatic
Highlight Airport
Click the Assist Me button
In the popup window click the Diagnostic button.
System Preferences/Network- Unlock padlock. Highlight Airport. Network Name-select your name. Click on the Advanced button. Airport/Preferred Networks-delete all that is not your network.
Place a check mark next to "Remember networks this computer has joined." Click the OK button and lock the padlock. Restart your computer.
http://support.apple.com/kb/TS1920 Mac OS: How to release and renew a DHCP lease
No internet connection (wireless)
Check to see if an extra entry is present in the DNS Tab for your wireless connection (System Preferences/Network/Airport/Advanced/DNS).
Delete all extra entries that you find.
Place a check mark next to "Remember networks this computer has joined."
Other resources to check into:
http://www.netspotapp.comNetspot
How to diagnose and resolve Wi-Fi slow-downs
Pv6 troubleshooting
Mac OS X 10.6 Help: Solving problems with connecting to the Internet
What Affects Wireless Internet?
Solutions for connecting to the Internet, setting up a small network, and troubleshooting

How to find the MAC address of iPod Shuffle?

Hi,
I need to add MAC address of iPod shuffle to the wireless router. Does anyone know how to find the MAC address of iPod shuffle? I would appreciate your help! Thanks.

Thanks for reply. So then I am not sure why my laptop is not recognizing iPod shuffle when it is connected through USB cable. I don't see DEVICES option under iTunes..so can't sync the music.

How to find the number of data items in a file written with ArryToFile function?

I have written an array of number in 2 column groups to a file using the LabWindows/CVI function ArrayToFile...Now if I want to read the file with FileToArray Function then how do I know the number of items in the file. during the write time I know how many array items to write. but suppose I want the file to read at some later time then How to find the number of items in the file,So that I can read the exact number and present it. Thanks to all
If you are young work to Learn, not to earn.
Solved!
Go to Solution.

What about:
OpenFile ( your file );
cnt = 0;
while ((br = ReadLine ( ... )) != -2) {
if (br == -1) {
// I/O error: handle it!
break;
cnt++;
CloseFile ( ... );
There are some ways to improve performance of this code, but if you are not reading thousands of lines it's quite fast.
After this part you can dimension the array to pass to FileToArray... unless you want to read it yourself since you already have it open!
Proud to use LW/CVI from 3.1 on.
My contributions to the Developer Zone Community
If I have helped you, why not giving me a kudos?

How to find the number of entries in a master data table

Hi Experts,
I am trying to find the entries in 0CUSTOMER master data.
BW>LISTCUBE>Data target: 0CUSTOMER and selected the fields that I need.
I would like to know how to find the "number of entrees". I tried to run the SUM for a count field, but it is taking forever as there are huge number of records .

Hi Dev,
Go to the change/display mode of the info object (0CUSTOMER) in your case. Go to the Master data/Text tab. Here you will find the master data tables according to your settings (P orQ or X or Y). Double click on the table name and it will take you to the SE11 display. From there, you can check the number of records as you do in any transparent table.
Hope this helps.
Thanks and Regards
Subray Hegde

How to find the number of links in a website

hi every body
can any one clear my doubt
my doubt is that
in a website how to find the number of links the hole website contains
is there any navigation tool to find that
plz help me yar
i am waiting for the reply

If you're talking about commercial sites (sites you don't have the source code for) I'm not sure.
If you want to count the links in site that you have the source code for, it should be relatively easy to write a Java application to do it. All you really need to do is have a list of the files you want to count links in, read each file line by line and check for the existance of the <a> tag in each line. Anywhere their is an <a> tag there is a link.
Hope this helps.

How to find the number of times method being called.....

hi,
can any one pls tell me how to find the number of times the method being called......herez the example....
Refrence ref = new Refrence();
for(int i = 0;i < arr.length; i++){
if(somecondition){
ref.getMethod();
here i want to know how many times the getMethod() is calling...Is there any method to do this.. i have seen StrackTraceElement class..but not sure about that....pls tell me the solution....

can any one pls tell me how to find the number of times the method being called......
herez the example.... http://www.catb.org/~esr/faqs/smart-questions.html#writewell
How To Ask Questions The Smart Way
Eric Steven Raymond
Rick Moen
Write in clear, grammatical, correctly-spelled language
We've found by experience that people who are careless and sloppy writers are usually also careless and sloppy at thinking and coding (often enough to bet on, anyway). Answering questions for careless and sloppy thinkers is not rewarding; we'd rather spend our time elsewhere.
So expressing your question clearly and well is important. If you can't be bothered to do that, we can't be bothered to pay attention. Spend the extra effort to polish your language. It doesn't have to be stiff or formal ? in fact, hacker culture values informal, slangy and humorous language used with precision. But it has to be precise; there has to be some indication that you're thinking and paying attention.
Spell, punctuate, and capitalize correctly. Don't confuse "its" with "it's", "loose" with "lose", or "discrete" with "discreet". Don't TYPE IN ALL CAPS; this is read as shouting and considered rude. (All-smalls is only slightly less annoying, as it's difficult to read. Alan Cox can get away with it, but you can't.)
More generally, if you write like a semi-literate b o o b you will very likely be ignored. So don't use instant-messaging shortcuts. Spelling "you" as "u" makes you look like a semi-literate b o o b to save two entire keystrokes.

How to find the number of fetched lines from select statement

Hi Experts,
Can you tell me how to find the number of fetched lines from select statements..
and one more thing is can you tell me how to check the written select statement or written statement is correct or not????
Thanks in advance
santosh

Hi,
Look for the system field SY_TABIX. That will contain the number of records which have been put into an internal table through a select statement.
For ex:
data: itab type mara occurs 0 with header line.
Select * from mara into table itab.
Write: Sy-tabix.
This will give you the number of entries that has been selected.
I am not sure what you mean by the second question. If you can let me know what you need then we might have a solution.
Hope this helps,
Sudhi
Message was edited by:
Sudhindra Chandrashekar

How to find the number of occurance of a string in text field of Infopath form?

Hi All,
In Infopath text field, How to find the number of occurrence of a particular string in that field?
Thanks in advance!

You can check to see if it contains a string once by using the contains function, but there isn't a very clean way to do what you want. If you wanted to guess at the maximum number of occurrences, then you could:
Box A has your initial. Set Box B to do a concat of string-before and string-after of Box A where it copies Box A minus the string we're looking for. Then we have Box C that does the same thing to Box B. Repeat as many times as you see necessary.
Example:
String: "1"
Box A - "123451234512345"
Box B - "23451234512345"
Box C - "2345234512345"
Box D - "234523452345"
etc.
We then have a field that has nested ifs looking backwards from Z -> A looking for a non-blank. Based on that, we return the number of occurrences. Again, this isn't clean, but it will work if you think there's a predefinable maximum.
Andy Wessendorf SharePoint Developer II | Rackspace [email protected]

How to find the number of users connected to database from OS level(Linux)

Hi All,
Could anyone know , how to find the number of users connected to database without connecting with sql*plus
is there any command to find it?
example we have 10 databases in one server, how to find the number of users connected to particular database without connecting to database(v$session)?
oracle version:- 10g,11g
Operating System:- OEL4/OEL5/AIX/Solaris
any help will be appreciated.
Thanks in advance.
Thank you.
Regards,
Rajesh.

Excellent.
Tested, works as long as you set the ORACLE_SID first ( to change databases )
ps -ef | grep $ORACLE_SID | grep "LOCAL=NO" | awk '{print $2}' | wc -l
Thanks!
select OSUSER
from V$SESSION
where AUDSID = SYS_CONTEXT('userenv','sessionid')
and rownum=1;Best Regards
mseberg

How to find the number simultaneous call at a given moment on UCCX ?

Hello,
I would to know how to find the number simultaneous call at a given moment on UCCX ?
it's on UCCX or UCCX RTMT, I don't know thanks a lot for your help.
Aubert

Hi Gergely,
I should made a report on the number simultaneous call at a given moment on UCC on the server (all calls on the server)..

How to find the Wireless LAN adaptor on my Satellite L350-21U

Similar Messages

Maybe you are looking for