How to fix blurring after enlarging jpeg
Hello, new here so bear with me. Enlarged and cropped a Jpeg and it got real blurry and lost the true image color. Can I get it back to it's origin at that larger size ?
Anytine you crop a picture, you throw information away. So when you enlarge the file it has fewer DPI dots per inch, hence it will be soft. You should use image> resize, and have the "resample" box checked, with the method set on "bicubic" or "bicubic smoother". Basically, for printing you want about 300 DPI if you intend to print the image. So, an 8 x 10 inch print would have dimensions of 2400 x 3000 pixels. For the purposes on this discussion, a pixel and a dot are the same thing. Some people recommend only resampling each time about 10%. So you would sort of go "step by step" until you reach the desired resolution.
"On One Software" sell" a program called "Genuine Fractals" http://www.ononesoftware.com/detail.php?prodLine_id=7 This is an expensive solution, but supposedly the best way of enlarging without apparent loss.
The most elegant, best, and recommended solution is to take pictures that don't require cropping.
So fill up the frame by, getting up the nerve to get closer, buy a longer lens, or do both.
Similar Messages
-
Any ideas on how to fix ipad after the new iOS 7 update? My battery will not charge, my ipad is hot to the touch, the iTunes Store won't open, and my messages on Facebook aren't showing up when I chat and pintrest won't pin to my boards.
If you have all your music on the cmputer then i would connect up my phone uncheck the Sync Music option and apply.
This should take all the music off your phone .Then you can resync the music back on to it.
If this doesn't work maybe a restore to factory settings and start from scratch is the way to go -
How to fix Grub after moving arch to new drive [SOLVED]
I moved my Arch install (/ and /home partitions) to a new drive and I was wondering how to fix Grub so that it knows /boot is on the new drive. What I've done thus far is
create partitions on the new drive and dd my current / and /home partitions to them. The new partitions are bigger than the current ones, so I also re-sized the filesystems to fill the new partitions. My disk/partition setup is the following
/dev/sda1 2048 488392703 488390656 232.9G 7 HPFS/NTFS/exFAT (Storage)
/dev/sdb1 * 2048 206847 204800 100M 7 HPFS/NTFS/exFAT (System reserved)
/dev/sdb2 206848 102402047 102195200 48.7G 7 HPFS/NTFS/exFAT (Windows 7)
/dev/sdb3 * 102402048 141472127 39070080 18.6G 83 Linux (Current Arch /)
/dev/sdb4 141472128 250069679 108597552 51.8G 83 Linux (Current Arch /home)
/dev/sdc2 * 206848 105064447 104857600 50G 83 Linux (New Arch /)
/dev/sdc3 105064448 234441647 129377200 61.7G 83 Linux (New Arch /home)
After I resized the filesystems, I then created a new grub.cfg file (on /dev/sdb3) that is aware of the new Arch system. I can boot to both my current and new Arch installs and run them fine, but ultimately I want to remove the current Arch install so I can make more room for my Windows 7 install. What do I need to do to grub, so it knows to use the new Arch system.
Last edited by tlawren (2014-08-17 21:42:46)@Xyne - Thanks! Installing grub on my /dev/sdc did the trick. Because I dd'ed my old setup to a new drive, /boot/grub was already populated, so all I had to do was install and configure grub on the new drive via the following.
grub-install --target=i386-pc --recheck --debug /dev/sdx
grub-mkconfig -o /boot/grub/grub.cfg
I used os-prober to find the other OS's (Windows 7 and my old Arch). After some testing, I will wipe my old Arch setup and then resize Windows into the free space. -
How to fix iPhoto after installing idvd
how do I fix iPhoto after installing idvd?
That's because you didin't do a custom install and installed only iDVD.
OT -
[Solved]How to fix grub after Windows XP install?
I installed Windows XP on top of Arch in a different partition.
It looks something like this:
/dev/sda1 - XP
/dev/sda2 - Arch
/dev/sda3 - Swap
Grub is located on /dev/sda2/ in /boot/grub/
Windows XP obviously overwritten the mbr like it normally does.
I tried loading the arch live install cd, and trying grub-install /dev/sda and /dev/sda1 and /dev/sda2 but it doesn't do anything.
I want to overwrite Windows XP's boot loader with grub and add XP as an option to boot. Can someone please give me noob friendly instructions on how to accomplish this with minimal effort? It's important I don't damage the XP or Arch partitions. Thanks for any help.
Last edited by PrimoTurbo (2008-07-30 18:06:43)I fixed it! Nearly the same instructions as lucke gave but I just used the Arch Live cd. All I did was boot Arch Live cd, it presented me with grub and bunch of options. (I didn't even boot into the cd) just pressed C so it loaded the grub terminal.
Then:
find /boot/grub/stage1
Which outputs:
root (hdX,Y)
(In my case it was hd0,1)
Then:
root (hdX,Y)
[Don't forget there is space after root and (hdX,Y)]
Finally:
setup hd0 -
At a total loss on how to fix PSCS6 after CSCC Install
I am assuming that the CC version of Photoshop had something to do with this as it started just after the install and they are both doing this.
The very next image I edited after the install was gif_01.gif. I saved it to: project/005885/site/image/gif_01.gif.
Soon I started working on another graphic and went to save it, say.... desktop\graphic.jpg
The warning box pops up, Warning, saving this image will overwrite the image gif_01.gif do you want to continue.
Now, everytime I save a jpeg it has this message. No other images do it, except of course gif_01.gif if in that folder.
Not a huge deal except for it is having a bit of a water board effect and is starting to feel like someone died every time it pops.
Shift+Ctrl+Alt+DBLClick = Reseting up my whole work environment and still having the gif issue. Oh ya, another issue with it is every time I save a jpeg to any file it also save that gif image to the file. It is an 1800x2400 pixel image so it will really suck to have a few thousand extra on the drives.
Any clues would be great. I hate to uninstall and reinstall as I am software heavy on this machine and it is used for many tasks. Sometime reinstalling a single program turns into setting the machine back up and it is a 3 day process.
Windows 8 Enterprise
CS6 - All Apps +(
MS Visual Studio Ultimate
Netbeans
Eclipse
MS Office Professional 2013 +Skype +Sharepoint Builder +Forms Tools
Core FTP
PUTTY (3 app pack)
Windows Defender
Spybot (dormat-manual scans and immunizations)
Windows Firewall
Everything file searcing app
Skype
Custom Apps (In House, Air Apps)
All of the internet browsers (at least the most popular dozen or so)
Mobile simulator, graphics pad software, video capture etc. Several more apps but none that should effect this)
AMD 8 Core
2xGTX 570 (Quadro 6K soon)
64gb Ram
SSD eSata III 512gb x 4 in Raid 10
1200watt PSU
Also, I have cleared as many of the temp files and etc. I use 2 256gb SSD eSata II disks for scratch and temp files for CS6 with a 300GB HDD for video
Every program system wide and all drivers are 100% up to date with the latest versions.
Also, I just realized it only does it when Save for the WEB is chosen and not when Save As and then JPEG is picked.I would hazard a guess you copied your plugins from cs6 to the cc installation which is not recommended!
Don't think the advice to reformat and reinstall is the best way and don't know why it was suggested! -
Hello,
WARNING! THIS IS AN ADVANCED FIX FOR TECHNICAL TECHS WITH OUT OF WARENTEE ROUGHTERS. IF LINKSYS SUPPORT CAN HELP YOU, USE THERE SERVICES FIRST! THIS PROCEDURE MAY RESULT IF PURMADENT LOSS OF USE OF YOUR ROUGHER. THIS WORKED FOR ME, IT MAY NOT FOR YOU!
Situation:
Linksys WRT310n V1
Power LED on solid
LAN Ports LED on solid
Wireless LED off
NO RESPONCE AT ALL!
PC hardware tested (only one is needed):
Vista laptop gigibit card.
Vista desktop gigibit card.
Software to download / install:
Installed vista TFTP client from control pannel
download TFTP from linksys
download firmware from linksys ( Proper firmware for v1 hardware!!!! )
Method and Procedure:
Plug in the power and the lan cable to the computer.
Open a dos prompt start pinging the roughter.
ping 192.168.1.1 -t -w 5
No responce is to be expected at this point.
On the computer open your network connections folder
Disable ALL OTHER network interfaces! (ALL OTHER)
open the settings of the lan interfacess.
disable (uncheck) all options other then tcp/ip v4
set the manual address of the card to
192.168.1.10 ip
255.255.255.0 sub
192.168.1.1 gate
192.168.1.1 dns
now in the network card properties above configure the network card for 10 half duplex speed mine was called line speed and duplex.
save and close.
NOTE: Do not release the reset button untill told to! You will need to hold it in for a long time!
NOTE: when holding the reset for 30 seconds, the LAN port may flash around 5 and 15 seconds, do not pull the power until the lan is off around 25 to 35 seconds of holding
On the rougher, with the power on and the lan cable connected.
Hold the reset button for 30 secconds you will see the lan cable port turn off arround this point pull the power.
Hold the reset and wait 10 seconds.
Hold the reset and power up for 30 seconds until the lan cable turns off around then
Ok so with the power off you can release the reset button.
from now own you can start from here with the reset if first attempts of sending the new firmware to the linksys fails.
Open a NEW dos prompt.
type tftp -i 192.168.1.1 put C:\linksysfirmware.bin
if you hit enter it will fail ... so let it time out... if you did type it again and wait to hit enter.
while holding in the reset button power on the roughter release the reset after 5 secconds.
press enter on the dos prompt. you may send this a couple of time arround now it took three tryes to get the "SENT COMPLETE" message from tftp! you will also magicaly see your pings from the other window start working! if working WAIT 2 min before doing anything next.
If you fail for more then 1 min, unplug your roughter and start the send firmware part.
ok so it's pinging thats all? yes!
ok so you waited 2 min, now pull the power normaly and wait 10 secconds return the power with our the restart! start it normaly.
after 20 secconds the roughter should be able to ping ... nothing else yet!
use the Linksys TFTP program now ... and install the full firmware to the roughter!
when the message says firmware complete wait two min then pull the power and reboot.
DONE!
Solved!
Go to Solution.[email protected] wrote:
Hello,
WARNING! THIS IS AN ADVANCED FIX FOR TECHNICAL TECHS WITH OUT OF WARENTEE ROUGHTERS. IF LINKSYS SUPPORT CAN HELP YOU, USE THERE SERVICES FIRST! THIS PROCEDURE MAY RESULT IF PURMADENT LOSS OF USE OF YOUR ROUGHER. THIS WORKED FOR ME, IT MAY NOT FOR YOU!
Situation:
Linksys WRT310n V1
Power LED on solid
LAN Ports LED on solid
Wireless LED off
NO RESPONCE AT ALL!
PC hardware tested (only one is needed):
Vista laptop gigibit card.
Vista desktop gigibit card.
Software to download / install:
Installed vista TFTP client from control pannel
download TFTP from linksys
download firmware from linksys ( Proper firmware for v1 hardware!!!! )
Method and Procedure:
Plug in the power and the lan cable to the computer.
Open a dos prompt start pinging the roughter.
ping 192.168.1.1 -t -w 5
No responce is to be expected at this point.
On the computer open your network connections folder
Disable ALL OTHER network interfaces! (ALL OTHER)
open the settings of the lan interfacess.
disable (uncheck) all options other then tcp/ip v4
set the manual address of the card to
192.168.1.10 ip
255.255.255.0 sub
192.168.1.1 gate
192.168.1.1 dns
now in the network card properties above configure the network card for 10 half duplex speed mine was called line speed and duplex.
save and close.
NOTE: Do not release the reset button untill told to! You will need to hold it in for a long time!
NOTE: when holding the reset for 30 seconds, the LAN port may flash around 5 and 15 seconds, do not pull the power until the lan is off around 25 to 35 seconds of holding
On the rougher, with the power on and the lan cable connected.
Hold the reset button for 30 secconds you will see the lan cable port turn off arround this point pull the power.
Hold the reset and wait 10 seconds.
Hold the reset and power up for 30 seconds until the lan cable turns off around then
Ok so with the power off you can release the reset button.
from now own you can start from here with the reset if first attempts of sending the new firmware to the linksys fails.
Open a NEW dos prompt.
type tftp -i 192.168.1.1 put C:\linksysfirmware.bin
if you hit enter it will fail ... so let it time out... if you did type it again and wait to hit enter.
while holding in the reset button power on the roughter release the reset after 5 secconds.
press enter on the dos prompt. you may send this a couple of time arround now it took three tryes to get the "SENT COMPLETE" message from tftp! you will also magicaly see your pings from the other window start working! if working WAIT 2 min before doing anything next.
If you fail for more then 1 min, unplug your roughter and start the send firmware part.
ok so it's pinging thats all? yes!
ok so you waited 2 min, now pull the power normaly and wait 10 secconds return the power with our the restart! start it normaly.
after 20 secconds the roughter should be able to ping ... nothing else yet!
use the Linksys TFTP program now ... and install the full firmware to the roughter!
when the message says firmware complete wait two min then pull the power and reboot.
DONE!
hi
i tried ur all steps but couldn't success, and the different thing is my when I connect my wrt310n to computer I show the IP 169.254.*.* is there any different steps for it. plz help me. -
How to fix Gridview after reloading Grid in Adobe flex-
hi folks,
i have searched a lot but could not find the exact way to do this... you will understand better if you will look once this page.please open this in IE.
http://www.freescale.com/webapp/search/MainSERP.jsp?SelectedAsset=Orderable%20Parts#breadc rumb_anchor
Here is my scenario goes...
click om power Actuation present in leftnav under Analog & Power Management. you will get result table and above that i have a container which shows different filter criteria. now find a filterable header(match header name with filter header) that is out of the screen fold to the righ,then Choose a value for filter exercise, filter by it.
now here my problem arises
after reloading the results, the table-view comes back to it's starting position, which creates the confusion to end user about the results.
so my question is how can i prevent my table-view to gets back to it's starting point?
i want the scenario which i described above, should work in this way.
Value is chosen for filtering, filtering starts, the reloaded values appear in the same screen position, as before the value was chosen.
i thought about viewStack but could not figure about how to do?
any suggestion or solution will highly appreciated!!!!!
Thanks in advance for your valuable time which you spend to read my question.
Thanks,
Vivek[discussion moved to Creating, Editing & Exporting PDFs forum]
-
How to fix permissions after a restore
I did a backup and restore of a site collection in 2010. Now subsites are unavailable with access denied error messages. How do correct this? I've done preliminary searchin for powershell commands but I'm not finding anything quickly...
Anyone have a link that will explain how to reset permissions on a site collection and/or its subweb's?
Kevin W. GagelHi,
Try to login the subsite using your application account.
If you can’t login it, please grant the full control in application policy of the application in Admin site.
How to do this, please refer to
http://technet.microsoft.com/en-us/library/ff608071.aspx
after you login in this site, you can reset the permissions.
Hope this helps
Thanks!
Stanfford -
Someone please tell me WHY i can"t download the cc installer? I have literally tried everything they told me on customer support (which is a very horrible place that provides no help) and I scowered all through the internet to fix this! No answer found!
http://helpx.adobe.com/creative-cloud/kb/a12e1-error-downloading-creative-cloud.html
For anything beyond that you will have to provide proper technical info about your system and otehr details, which you have not done so far.
Mylenium -
How to fix bootcamp after partitioning
macbookpro md102 mac osx 10.9+windows 8
so obviously i tried splitting my windows c to two parts using default windows program via a wiki on the net.
i shrinked it and then used allocated area to create a new disk
after i did it i got a warning that said: this may damage bootcamp (dont exactly remember) and i passed it easy and i wish i listened to it
after i did it i went to my computer trying to check on my new partition but i saw some other partitions that i didnt see before
so i passed through that too.then i restarted to see if my os x is working or not and suddenley when i restarted and pressed option i just saw windows
not macintosh hd not recovery disk
now when i boot into windows it says repairing windowns and stuff
is there a way to have my windows without reinstalling?
guys please i know you dont have too but please do something my life depends on itRemove the drive and put it in an external case, put a new drive in the nachine and reinstall OSX, connect the old (now external) drive and see if there is any data left for you to recover.
Next time, backup before you start, not after you make the mistake. -
Subtitle turn blur after render
anyone know how to fix blurred subtitle after rendering? It looks great as i create it but then turned blurry as soon as i render the sequence to export.
thanx
Trangno, i dont think it's the case, it's less than 62% and in title safe area. From the FCP Manual they also admit the prob of blur titles because of this interlacing stuff. But how do u guys face that? Do u just put up with it? I tried all safe advices from FCP (certain fonts, bigger than 25, bold, opacity 90%, etc) but my titles aint "better looking" enuf.
anyone guarantee better lookin titles using other text generators?
thanx -
Strange colour spots (red&green) appear after RAW files converted to JPEG, anyone know how to fix it? Thanks.
I use "Export" function to convert the picture from RAW format to JPEG format, resolution 240 pixels per inch. Strange red dots appeared in the area supposed to be dark grey, as per the picture below. The red colour does not appeared in the original RAW picture when viewing from Lightroom, only exist in the JPEG it created. Any ideas how to fix this? Thanks!
-
can anyone help me with Magicjack? after I purchased US number I am unable to log in on my Iphone, I keep getting an error "YOUR DEVICE IS NOT ON THIS ACCOUNT" I contacted MJ support but they are very much useless and dont know how to fix it!
There's a whole lot to read in your post, and frankly I have not read it all.
Having said that, this troubleshooting guide should help:
http://support.apple.com/kb/TS1538
In particular, pay attention to the mobile device support sections near the bottom, assuming you have already done the items above it. -
After moving to iCloud I can only get my email through the cloud, no new emails are making it to my home computer and .mac account. Does anyone have any advice on how to fix this issue?
Welcome to the Apple Community.
Which OS are you using.
Maybe you are looking for
-
Forgetting Weight in Pedometer every time I sync
Every time I finished syncing with my iTunes, my iPod always forgot my weight in Settings. I have to go back to Settings to set it again. For example, the original setting is 56.5 Kg. It turns to lbs after it synced. Maybe it converted from kg to lbs
-
Apps missing from Library sidebar after 10.1 update
Installed 10.1 yesterday and ever since the apps selection from the library is missing. I experienced problems installing 10.1 yesterday, would not run via the update selection from within iTunes. Instead, I manually downloaded and ran each component
-
Access Database in sharepoint 2013
We have a new server here at work. One of the virtual servers on this server has an installation of sharepoint 2013. I have installed and configured many previous installations of sharepoint, 2013 is quite the different animal and I am working thro
-
PDF Reader Problem for Persian PDF's in FF31
Hi, FF31 Won't show Persian PDF's properly. all characters are busted together and unreadable, I asked a friend and check it on mac and Linux. Is that a bug or something?
-
SLD Check Failed (LCR_LIST_BUSINESS_SYSTEMS function doesn't work)
Hi all, I have done SLDCHECK but then got this result below : Already verify all the user working fine, please advise me. Thank you and Regards Fernand Properties of RFC destination SAPSLDAPI RFC host: %%RFCSERVER%% program id: NWA_PROGRAM