How to fix iPhoto after installing idvd

how do I fix iPhoto after installing idvd?

That's because you didin't do a custom install and installed only iDVD.
OT

Similar Messages

WRT310N V1 - How to fix firmware after installing firmware v2 on v1 hardware. ** SOLVED **

Hello,
WARNING! THIS IS AN ADVANCED FIX FOR TECHNICAL TECHS WITH OUT OF WARENTEE ROUGHTERS. IF LINKSYS SUPPORT CAN HELP YOU, USE THERE SERVICES FIRST! THIS PROCEDURE MAY RESULT IF PURMADENT LOSS OF USE OF YOUR ROUGHER. THIS WORKED FOR ME, IT MAY NOT FOR YOU!
Situation:
Linksys WRT310n V1
Power LED on solid
LAN Ports LED on solid
Wireless LED off
NO RESPONCE AT ALL!
PC hardware tested (only one is needed):
Vista laptop gigibit card.
Vista desktop gigibit card.
Software to download / install:
Installed vista TFTP client from control pannel
download TFTP from linksys
download firmware from linksys ( Proper firmware for v1 hardware!!!! )
Method and Procedure:
Plug in the power and the lan cable to the computer.
Open a dos prompt start pinging the roughter.
ping 192.168.1.1 -t -w 5
No responce is to be expected at this point.
On the computer open your network connections folder
Disable ALL OTHER network interfaces! (ALL OTHER)
open the settings of the lan interfacess.
disable (uncheck) all options other then tcp/ip v4
set the manual address of the card to
192.168.1.10 ip
255.255.255.0 sub
192.168.1.1 gate
192.168.1.1 dns
now in the network card properties above configure the network card for 10 half duplex speed mine was called line speed and duplex.
save and close.
NOTE: Do not release the reset button untill told to! You will need to hold it in for a long time!
NOTE: when holding the reset for 30 seconds, the LAN port may flash around 5 and 15 seconds, do not pull the power until the lan is off around 25 to 35 seconds of holding
On the rougher, with the power on and the lan cable connected.
Hold the reset button for 30 secconds you will see the lan cable port turn off arround this point pull the power.
Hold the reset and wait 10 seconds.
Hold the reset and power up for 30 seconds until the lan cable turns off around then
Ok so with the power off you can release the reset button.
from now own you can start from here with the reset if first attempts of sending the new firmware to the linksys fails.
Open a NEW dos prompt.
type tftp -i 192.168.1.1 put C:\linksysfirmware.bin
if you hit enter it will fail ... so let it time out... if you did type it again and wait to hit enter.
while holding in the reset button power on the roughter release the reset after 5 secconds.
press enter on the dos prompt. you may send this a couple of time arround now it took three tryes to get the "SENT COMPLETE" message from tftp! you will also magicaly see your pings from the other window start working! if working WAIT 2 min before doing anything next.
If you fail for more then 1 min, unplug your roughter and start the send firmware part.
ok so it's pinging thats all? yes!
ok so you waited 2 min, now pull the power normaly and wait 10 secconds return the power with our the restart! start it normaly.
after 20 secconds the roughter should be able to ping ... nothing else yet!
use the Linksys TFTP program now ... and install the full firmware to the roughter!
when the message says firmware complete wait two min then pull the power and reboot.
DONE!
Solved!
Go to Solution.

[email protected] wrote:
Hello,
WARNING! THIS IS AN ADVANCED FIX FOR TECHNICAL TECHS WITH OUT OF WARENTEE ROUGHTERS. IF LINKSYS SUPPORT CAN HELP YOU, USE THERE SERVICES FIRST! THIS PROCEDURE MAY RESULT IF PURMADENT LOSS OF USE OF YOUR ROUGHER. THIS WORKED FOR ME, IT MAY NOT FOR YOU!
Situation:
Linksys WRT310n V1
Power LED on solid
LAN Ports LED on solid
Wireless LED off
NO RESPONCE AT ALL!
PC hardware tested (only one is needed):
Vista laptop gigibit card.
Vista desktop gigibit card.
Software to download / install:
Installed vista TFTP client from control pannel
download TFTP from linksys
download firmware from linksys ( Proper firmware for v1 hardware!!!! )
Method and Procedure:
Plug in the power and the lan cable to the computer.
Open a dos prompt start pinging the roughter.
ping 192.168.1.1 -t -w 5
No responce is to be expected at this point.
On the computer open your network connections folder
Disable ALL OTHER network interfaces! (ALL OTHER)
open the settings of the lan interfacess.
disable (uncheck) all options other then tcp/ip v4
set the manual address of the card to
192.168.1.10 ip
255.255.255.0 sub
192.168.1.1 gate
192.168.1.1 dns
now in the network card properties above configure the network card for 10 half duplex speed mine was called line speed and duplex.
save and close.
NOTE: Do not release the reset button untill told to! You will need to hold it in for a long time!
NOTE: when holding the reset for 30 seconds, the LAN port may flash around 5 and 15 seconds, do not pull the power until the lan is off around 25 to 35 seconds of holding
On the rougher, with the power on and the lan cable connected.
Hold the reset button for 30 secconds you will see the lan cable port turn off arround this point pull the power.
Hold the reset and wait 10 seconds.
Hold the reset and power up for 30 seconds until the lan cable turns off around then
Ok so with the power off you can release the reset button.
from now own you can start from here with the reset if first attempts of sending the new firmware to the linksys fails.
Open a NEW dos prompt.
type tftp -i 192.168.1.1 put C:\linksysfirmware.bin
if you hit enter it will fail ... so let it time out... if you did type it again and wait to hit enter.
while holding in the reset button power on the roughter release the reset after 5 secconds.
press enter on the dos prompt. you may send this a couple of time arround now it took three tryes to get the "SENT COMPLETE" message from tftp! you will also magicaly see your pings from the other window start working! if working WAIT 2 min before doing anything next.
If you fail for more then 1 min, unplug your roughter and start the send firmware part.
ok so it's pinging thats all? yes!
ok so you waited 2 min, now pull the power normaly and wait 10 secconds return the power with our the restart! start it normaly.
after 20 secconds the roughter should be able to ping ... nothing else yet!
use the Linksys TFTP program now ... and install the full firmware to the roughter!
when the message says firmware complete wait two min then pull the power and reboot.
DONE!
hi
i tried ur all steps but couldn't success, and the different thing is my when I connect my wrt310n to computer I show the IP 169.254.*.* is there any different steps for it. plz help me.

This update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled... this comes up when I go to update Iphoto after installing Yosemite... how do I fix this?

This update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled... this comes up when I go to update Iphoto after installing Yosemite... how do I fix this?

I have resolved this issue with the apple chat support by going to the "purchases" tab in the app store - where there was a message that I had to accept updates for the apps that wouldn't update. Once I did this, signing in for each of them, they all updated just fine.

Issues printing with iPhoto after installing OS X 10.10.2

After working with 2nd and 3rd level Apple Support I was able to print photos using iPhoto after installing OS X 10.10.2. I have an HP 7520 all in one ePrinter and the latest Yosemite driver have been installed. When I tried to print a photo using iPhoto the application would hang and I had to force quit to continue. Apple support was able to identify the problem. The iPhoto application had an outstanding print job listed in the Recent heading on the left side of the screen, I do not know how this happened, but after clearing out this print job I was able to print from iPhoto. The Apple Support person said I could avoid this problem by hitting the cancel button located near the print button on the bottom of iPhoto, after any print activity had finished. He said this was a known problem when using iPhoto and Yosemite.

EW,
Kernel Panics here on the same model. My problems started after the recent Firmware Update for Airport and Airport Expresses (7.6). No other new software installed besides the Firmware Update and they are occurring daily.
I haven't seen any remedies yet....

Should I trash iPhoto after installing Photo?

Should I trash iPhoto after installing Photo?

Should I trash iPhoto after installing Photo?
Why would you want to do that? You paid for it, and Photos cannot do everything that iPhoto can, for example add location data to photos or batch changing the titles. Don't trash iPhoto, before you have explored your migrated photos library thoroughly and are sure, that all photos migrated correctly, and before you have tested all features of the new Photos and are sure, that there are no hidden bugs on your system, that would require reverting to iPhoto until the bugs are fixed. And even if you, be sure, to keep a backup of iPhoto and your iPhoto library - best make a bootable clone of your system. Better be safe than sorry.

I purchased iPhoto after installing Yosemite, but App store shows the download is "waiting"

I purchased iPhoto after installing Yosemite, but App store shows the download is "waiting", with a greyed out box that says pause.

Hi exyankee,
Thanks for the question. If I understand correctly, an app is stuck on waiting. I would recommend that you read this article, it may be able to help you isolate or resolve the issue.
iTunes: How to resume interrupted iTunes Store downloads - Apple Support
Thanks for using Apple Support Communities.
Have a great day,
Mario

Any ideas on how to fix ipad after the new iOS 7 update? My battery will not charge, my ipad is hot to the touch, the iTunes Store won't open, and my messages on Facebook aren't showing up when I chat and pintrest won't pin to my boards.

Any ideas on how to fix ipad after the new iOS 7 update? My battery will not charge, my ipad is hot to the touch, the iTunes Store won't open, and my messages on Facebook aren't showing up when I chat and pintrest won't pin to my boards.

If you have all your music on the cmputer then i would connect up my phone uncheck the Sync Music option and apply.
This should take all the music off your phone .Then you can resync the music back on to it.
If this doesn't work maybe a restore to factory settings and start from scratch is the way to go

I can't update iPhoto after installing OSX 10.9.2, it has the name otto@**** in the apple ID box and will not let me change it. Any thoughts?

Hello people,
I can't update iPhoto after installing OSX 10.9.2, it has the name otto@**** in the apple ID box and will not let me change it. Any thoughts?
Thanks
<Email Edited By Host>

You installed a hacked app, originally from the Mac App Store. It contains the receipt for a different app, downloaded using an account that you don't control. You need to identify and remove the hacked app.
Important: The app you need to remove is not necessarily the one named in the App Store alert. For example, the App Store may prompt you to update "Angry Birds" or "Twitter," but the hacked app may be something else entirely. Don't make any assumptions about which app you're looking for. To find it, you must carry out a systematic search with Spotlight.
1. Triple-click anywhere in the line of text below on this page to select it:
kMDItemAppStoreHasReceipt=1
Copy the selected text to the Clipboard by pressing the key combination command-C.
2. In the Finder, press command-F to open a search window, or select
File ▹ Find
from the menu bar. In the search window, select
Search: This Mac
from the row of tokens below the toolbar. Below that is a popup menu of search criteria, initially showing Kind. From that menu, select
Other...
A sheet will drop down. In that sheet, select
Raw Query
as the criterion, then click OK or press return.
Now there will be a text box to the right of the menu of search criteria. That's where you enter the raw search query. Click in that box and paste the text you copied earlier by pressing command-V.
4. The search window will now show all the App Store products that are installed. Compare those search results with the list of your purchases from the App Store. To see the complete list, you may need to unhide hidden purchases. If any apps were download from the App Store using other Apple ID accounts that you control, sign in to the store under each of those ID's and check the purchases.
At least one of the apps in the Spotlight search results is not among your purchases in the App Store. Move each such item to the Trash, after quitting it if it's running. You may be prompted for your administrator password. Empty the Trash.
Quit and relaunch the App Store. Test.
If you find these instructions confusing, ask for an alternative method.

I can't update iPhoto after installing yosemite

i can't update or open iPhoto after installing yosemite

Ok so here's what you gonna do. (had this problem myself today, and after some fiddling figured out what to do.)
Find your old iPhoto with a cross through it, right-click it and select 'show package contents'. A folder will open. In that folder go to Contents>MacOS and there will be three little things there. Click on the one called 'iPhoto' and terminal will open. Leave terminal open and wait four seconds and VOILA! iPhoto opens. Leave terminal open until you are finished with iPhoto, because if you close terminal, iPhoto will close with it. THX! ENJOY! Hope it works.
P.S.
You can close terminal once you close iPhoto. I also suggest backing up your iPhoto library while you can.

Cannot access iphoto after installing Yosemite

cannot access iphoto after installing Yosemite
My icon for iPhoto has a X thru it when I try to re install through app store nothing happens

what version of Iphoto are you running there is an update available ver9.6

All of my pictures are gone from iPhoto after installing Yosemite..how do i get them back?

I have tried everything to get my pictures back after installing Yosemite on my laptop. Are they gone? Or is there a way to retrieve them?

Define "everything" because if you've tried everything then your last recourse is:
1 - restore your backup copy of your iPhoto Library created just prior to your Yosemite upgrade or
2 - Starting over from scratch with new library
Start over with a new library and import the Originals (iPhoto 09 and earlier) or the Masters (iPhoto 11) folder from your original library as follows:
1. Open the library package like this.
2. Launch iPhoto with the Option key held down and, when asked, select the option to create a new library.
3. Drag the subfolders of the Originals (iPhoto 09 and earlier) or the Masters (iPhoto 11) folder from the open iPhoto Library package into the open iPhoto window a few at a time.
This will create a new library with the same Events (but not necessarily the same Event names) as the original library but will not keep the metadata, albums, books slideshows and other projects.
Note: your current library will be left untouched for further attempts at a fix if so desired.

How to fix Grub after moving arch to new drive [SOLVED]

I moved my Arch install (/ and /home partitions) to a new drive and I was wondering how to fix Grub so that it knows /boot is on the new drive. What I've done thus far is
create partitions on the new drive and dd my current / and /home partitions to them. The new partitions are bigger than the current ones, so I also re-sized the filesystems to fill the new partitions. My disk/partition setup is the following
/dev/sda1 2048 488392703 488390656 232.9G 7 HPFS/NTFS/exFAT (Storage)
/dev/sdb1 * 2048 206847 204800 100M 7 HPFS/NTFS/exFAT (System reserved)
/dev/sdb2 206848 102402047 102195200 48.7G 7 HPFS/NTFS/exFAT (Windows 7)
/dev/sdb3 * 102402048 141472127 39070080 18.6G 83 Linux (Current Arch /)
/dev/sdb4 141472128 250069679 108597552 51.8G 83 Linux (Current Arch /home)
/dev/sdc2 * 206848 105064447 104857600 50G 83 Linux (New Arch /)
/dev/sdc3 105064448 234441647 129377200 61.7G 83 Linux (New Arch /home)
After I resized the filesystems, I then created a new grub.cfg file (on /dev/sdb3) that is aware of the new Arch system. I can boot to both my current and new Arch installs and run them fine, but ultimately I want to remove the current Arch install so I can make more room for my Windows 7 install. What do I need to do to grub, so it knows to use the new Arch system.
Last edited by tlawren (2014-08-17 21:42:46)

@Xyne - Thanks! Installing grub on my /dev/sdc did the trick. Because I dd'ed my old setup to a new drive, /boot/grub was already populated, so all I had to do was install and configure grub on the new drive via the following.
grub-install --target=i386-pc --recheck --debug /dev/sdx
grub-mkconfig -o /boot/grub/grub.cfg
I used os-prober to find the other OS's (Windows 7 and my old Arch). After some testing, I will wipe my old Arch setup and then resize Windows into the free space.

Why is that I am not able to update iPhoto after install os x yosemite? is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled.

"This update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled" iPhoto is gone after installing to OS X Yosemite. Where did it go and how do i get all my pictures back ??
HELP !!!

"This update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled" iPhoto is gone after installing to OS X Yosemite. Where did it go and how do i get all my pictures back ??
HELP !!!
Did you upgrade to Yosemite, without first updating to iPhoto 9.5.1 in Mavericks? Then updating to 9.6 may not work - it is buggy at the moment.
If you already own a version of iPhoto 9.x.x, but cannot update iPhoto, try to buy a new version. When I look at the AppStore, the price has now changed to "Free", so it should not matter if you buy again or update.
Delete iPhoto from Applications, but do not empty the Trash.
Go to the first page of the App Store and sign in with your AppleID.
Search for "iPhoto" using the Search field.
What does the button below the iPhoto icon show? If it is showing "Free" like for me, click "free" to purchase again.

How setup LDAP Sync After Install in OIM 11g ver, 11.1.1.5.0

Hi guys, I'm trying to find how to setup LDAP Sync After Install in OIM 11g (ver, 11.1.1.5)....
I found on Metalink an interesting article "*How to Setup LDAP Sync After Install in OIM 11g [ID 1272682.1]*", but inside there is a Note that says:
Note: This article is applicable to OIM version 11.1.1.3 only. Steps for 11.1.1.5 are not the same, and product manual has documented steps to setup LDAP sync after install.
So, that the steps for 11.1.1.5 are not the same, it's clear.....
and I tried to look for these steps in the manual:
Oracle® Fusion Middleware Quick Installation Guide for Oracle Identity Management
11g Release 1 (11.1.1)
Part Number E10033-06
but I didn't still find nothing for the specific 11.1.1.5.0 version....only for the 11.1.1.3.0 version
Can anyone help me to find where these steps are ? I need this information as soon as possible ti start the development
Thanks in advance for the help
Alex

If you are creating Before and After Create Opeation script, you would be able to access all the variables in the process form. Now obvious question, what are the names of these variables? The answer is: the name of the variable is same as that mentioned in the "decode" column of the provisioning attribute map lookup or in other words, the variable name is same as the AD attribute name. In the example mentioned in the documentation, the variable "%givenName% was used in the script. On the similar lines you can use other variables like "sn", "samAccountName", etc.
Hope the information helps.

Could not open iPhoto after installing Yosemite.

Could not open iPhoto from dock or launch pad after installing Yosemite. Went into the iPhoto application in applications and clicked on MAC OS and then clicked on iPhoto. iPhoto then opened but when I closed the exec window iPhoto closed.

Could not open iPhoto as a guest user.
Was able to open iPhoto in my account when I went to the application list, right clicked on the iPhoto application then chose Show Package Contents, then clicked on Contents and then clicked on MAC OS which then opened iPhoto.
This is the only way I have been able to open it.
Thanks

How to fix iPhoto after installing idvd

Similar Messages

Maybe you are looking for