How to fix paper feed problem after jam? Paper feeds out diagonally at page bottom. hp deskjet 920c

I have a HP Deskjet 920c printer. One sheet jammed in it, which I pulled out.  After that, it prints fine for the first 3/4 of the page, then the feed direction changes and the paper (and thus the printing) comes out diagonally.
I have Windows Vista.
Thank you

Hi Castor - I followed your instructions and did a semi-full reset after which the printer switched itself off.
I waited a couple of minutes, turned the printer on, answered the questions about language and region and the printer produced an alignment page which was then successfully scanned.  So at least that page was fed in and printed correctly. Sadly, with subsequent printed pages, I still had problems with the paper being picked up at a slight angle, printing too close to the top edge, picking up multiple pages when there's just a few pages left in the tray. 
So I did the semi-full reset again!  This time the alignment page was also printed at a slight angle and starting too near the top edge.  The printer refused to detect that alignment page, produced a second alignment page with similar poor printing and this time the printer screen stated: "Alignment Failed.......".
What to do now?
Regards, Richard

Similar Messages

  • How to fix the delay problem while recording? Can't set the Latency to 0. Win7, CS6,Realtek,C03u Mic

    I am using Win7, with CS6, Realtek soundcard and Samson C03U microphone.
    There is a problem that's really been bothering me. When I record songs the recorded audio always comes 0.1 seconds after where it's supposed to be and I need to fix the problem every time. How to fix the delay problem while recording? I can't set the Latency to zero. The minimum is 30ms and I still get an obvious delay.
    I saw some previous discussions saying that installing ASIO would help. Is it gonna work on my PC?
    Thank you in advance guys.

    You probably should look at a more 'serious' audio interface rather than the Realtek
    Yes ASIO drivers are the way to go
    If you want zero latency you need to monitor via your audio hardware (hence the 'serious' audio interface suggestion)
    There are a heap of reasonable audio interfaces which will do the job for you that are pretty inexpensive and I'm sure that someone will jump in with a suggestion

  • HT4623 how to fix my iphone 3gs after ios 6  ?there is no sim card install in the iphone you ar attempting to activate

    how to fix my iphone 3gs after ios 6  ?there is no sim card install in the iphone you ar attempting to activate

    Hello James,
    Thank you for the details of the issue you are experiencing with your iPhone.  I recommend following the steps in the article below if you are getting the message "No SIM" when your SIM card is installed:
    iPhone: Troubleshooting No SIM
    http://support.apple.com/kb/ts4148
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • Guys how to fix the audio problems of my itouch? The volume bar dosnt exist and the loudspeaker doesnt work. . .Sounds only works in headset  please help thanks!!!!

    Guys how to fix the audio problems of my itouch? The volume bar dosnt exist and the loudspeaker doesnt work. . .Sounds only works in headset  please help thanks!!!!

    Post this in the iPod Touch forum.
    https://discussions.apple.com/community/ipod/ipod_touch
    B-rock

  • HOW TO FIX THE WIFI PROBLEM

    HOW TO FIX THE WIFI PROBLEM: Settings > Wifi > (little blue arrow) > scroll down to "Renew Lease" and then click on it.
    Enjoy

    Didn't work for me.
    What did work was going to the Wifi network settings and setting the HTTP Proxy to Auto rather than Off.
    Worked for both iphone4S and ipad2.

  • I've no idea how to fix my service problem ?

    So a day or so ago my phone was having troubles finding wifi so I turned it on and off of airplane mode, it found the wifi , but soon after my service depleted ... I turned my phone on and off but the service did not return , I then reset the network settings and I had service again ! But only due to 3G which my plan doesn't cover so it had to be turned off ..I still have no service and I can't figure out how to fix it. So if you could tell me how that would be lovely !?? One more thing ..does 3G cost money , if it's not in your plan, but you are connected to wifi ? With 3G my phone gets 3 bars but without it goes to one bar immediately and then says "searching /no service " soon after
    I also don't know if I'm posting this in the right place or again, sorry :/

    It's hard to say what the problem is, but if you are concerned about data charges from using 3G you can turn off cellular data in Settings > Cellular to eliminate all doubt. Slide Cellular Data "off". That will constrain your data connection to Wi-Fi only.
    Have an Apple Store evaluate your iPhone.

  • How I fixed my conection problem

    Here's my setup:
    Wireless IP (Motorola canopy)
    The connection comes into the house as ethernet (I'm conected wirelessly to the ISP's router and it's using DHCP
    That's pluged into an airport express that acts as a bridge to the ISP's router
    iMac G4 wireless
    Windows xp notebook wireless using a Netgear PCMCIA card
    Son's XP desktop using a DLink internal wireless card
    Symptoms:
    This worked but after several hours the airport express wouls stop forwarding the new DHCP info. The green light was On but I could not connect to the internet wirelessly.
    Here's how I fixed it:
    I turned off ipv6 in the network settings. I had it set to Automatic. When I turned it off It has worked like it is suposed to.
    I hope this helps someone.

    The fact that you saw no glitches while running Logic before applying the update means almost nothing because that uses only a small subset of system resources. Far more significant is that Safe Mode restored some missing functionality: because it disables non-essential items like user fonts, third party drivers, & so on, it points to problems in those areas.
    Equally significant, the fact that there are relatively few reports of post-update problems among the several million Snow Leopard users points away from the update itself as the cause of your problems.
    Separate & apart from that, it so happens that I'm a sound engineer/system designer/board operator with nearly 40 years of professional touring experience. FWIW, I never have & never will update the software of any system I must rely on professionally (whether it is running on a Mac, a PC, or dedicated hardware) unless & until I can thoroughly test it first and I have a trustworthy backup/recursion strategy to fall back on in case of problems.
    I strongly suggest you learn from your unpleasant experience & do the same. I have had far fewer problems with Macs than with PC's, but nothing is 100% reliable to begin with. Changing the OS software part way through the tour is just asking for trouble, no matter how reliable that has been in the past. Even if the budget allows for nothing better than a stack of burned CD's & a couple of consumer grade CD players, no professional tour can afford to be without some fallback strategy in place. That should be self-evident & require no warning from Apple or anybody else.

  • How to fix exclamation mark problem

    Basically since I updated to iTunes 11 and I went to make a new cd to listen to in the car a lot of my songs have got an exclamation mark next to them and says it can't find the original file so since I HATE the new iTunes i decided to downgrade back to iTunes 10. what ever it was before the update came out to see if that would fix the problem but no that didn't work, so I've since been looking all over Google to try and find a solution to this but everything I found was mostly about moving the iTunes library and how to fix that problem but in my case that isn't the problem at all as I haven't moved the library anywhere, I did find a post about transferring purchases from my iPhone to iTunes so I did that thinking it would fix the problem as all the songs that have the exclamation mark next to them are on my iPhone and play back perfectly fine but iTunes would only transfer my app's not my music, is there a way to change this? Or if anyone else knows how to fix this problem in a different way I would very much appreciate the answer to this problem as it's driving me insane!
    Thanks in advance
    Jordan

    This happens if the files are no longer where iTunes expects to find them. Possible causes are that you or some third party tool has moved, renamed or deleted the files, or that the drive they live on has had a change of drive letter. It is also possible that iTunes has changed from expecting the files to be in the pre-iTunes 9 layout to post-iTunes 9 layout, or vice-versa, and so is looking in slightly the wrong place.
    Select a track with an exclamation mark, use CTRL+I to Get Info, then cancel when asked to try to locate the track. Look on the summary tab for the location that iTunes thinks the file should be. Now take a look around your hard drive(s). Hopefully you can locate the track in question. If a section of your library has simply been moved, or a drive letter has changed, it should be possible to reverse the actions.
    Alternatively, as long as you can find a location holding the missing files, then you should be able to use my FindTracks script to reconnect them to iTunes. See this post for a detailed explanation of what the script does.
    If your media is scattered around you may need to repeat the search using each of the different locations where you have stored things.
    tt2

  • Please tell me how to fix this annoying problem

    Whenever I open a new Safari window (apple-N) the page width falls just short of completely filling my monitor screen. I'd like it to go to the absolute extreme edge of my screen by default, how do I do this?

    I just posted a new topic with a possible fix to your problem. The topic's title is "Javascript Bookmark to resize Safari Windows", or try the following link:
    http://discussions.apple.com/thread.jspa?threadID=1317489&tstart=0

  • How to fixed stuck itunes logo after updating ios

    after i upadte it last 3 days only the itunes logo appear. i try to do the things that i saw in the net like pressing the home button and power and using the itunes but then uit doesnt work...i installed a latest version of itunes and only error appears it not even restore...pls someone know how to fixed it?thnx in advance

    FORCE IPAD INTO RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.

  • How to fix Software Update Problem?

    I was do some update includes new 10.5.1, iTunes, QuickTime, and many more, but today I test to check new update I got blank list and I was try to do via Terminal and got this message
    Software Update Tool
    Copyright 2002-2007 Apple
    XML parser error:
    Encountered unexpected EOF
    Old-style plist parser error:
    Malformed data byte group at line 1; invalid hex
    What's going on? and How to fix it my Leopard Software Update Problem

    (1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
    http://majorgeeks.com/download.php?det=4459
    (2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
    (3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
    (4) In the list of programs that appears in CleanUp, select any Apple Software Update entries and click "Remove", as per the following screenshot:
    (5) Quit out of CleanUp, restart the PC and try another iTunes install using an iTunesSetup.exe (or iTunes64Setup.exe) downloaded from the Apple Website:
    http://www.apple.com/itunes/download/
    Does it go through properly this time?

  • Print Paper Size Problem after Mavericks Upgrade

    I migrated my Apps, Data and System Settings from a Macbook running OSX Lion to a new Macbook Pro running Mavericks.
    The problem I now have is that the application 'Family Tree Maker 2' cannot get the paper size right. No matter which Paper size I select, it is shown as half size in the Application Print Preview screen and this error carries through to actual printing.
    so A4 210 by 297 mm displays as 5.8 x 4.1 inches (which is Half Size).
    The problem is significant because the application formats it's output to fit into half of the available space.
    I have unsuccessfully tried;
    - removing and reinstalling the Application.
    - Adding my Brother Laser printer with the latest Mavericks compatible driver.
    - Resetting the printing system.
    - Repairing disk permissions
    - Adding a new User Account
    - Deleting plists associated with com.ancestry
    iWork Pages is working correctly.
    I have raised this with ancestry.com however it appears that I am the only person that has experienced this problem.
    Any suggestions would be appreciated.

    Problem is worse than that. Whilst the Paper is shown as half size, the family tree diagram boxes are produced twice as wide as they should be.
    If I select A4 Paper, a diagram that would fit on one page is now spread across two.
    If I select A3 Paper, the preview indicates the paper size as A4 8.3 x 5.8 inches however the diagram size and position on the paper are unchanged and I just get loads of white space around the outside of the diagram.
    It does sound like an Application problem but it is still working fine on my old OSX Lion machine. Something has happened in the migration.

  • How to fix connecting to iTunes after upgrading to ios6

    How do I connect to iTunes  after upgrade to ios6

    iTunes on your computer or the iTunes store?
     Cheers, Tom

  • How to fix screen rotation problem in iphone 5s?

    screen is not tilting while playing and messaging on iphone 5s ios 8.1.3.
    is it a hardware fault or software?
    how to fix it now?

    Is "rotation lock" set in the Control Panel?
    The Control Panel is accessed by swiping up from the bottom of the screen. Check the icon with the padlock and circular arrow.

  • HOW TO FIX NO AUDIO PROBLEM IN FLASH (4 SOLUTIONS)

    This solution is for WINDOWS ONLY!!! Unfortunately I believe
    it is a bug in flash itself as I have read more than one instance
    of this same no audio problem occuring on MAC'S and LINUX based
    systems as well. IF YOU KNOW OF SOLUTIONS TO THE MAC OR LINUX BASED
    PROBLEMS, PLEASE POST THEM IN THIS THREAD.
    Description of the problem: Video sites such as YouTube,
    VideoSift, Break, Google Videos, Yahoo, and a plethora of others do
    not stream embedded audio. Viewing a YouTube video, for example, on
    VideoSift.com results in the video playing back with no audio.
    However, by going directly to YouTube and playing back the same
    video, it appears to work.
    THERE ARE SEVERAL POSSIBLE SOLUTIONS.
    Problem: You may be missing your WAVEMAPPER driver.
    Cause: Wavemapper driver was removed during installation or
    updating of the Flash Player. It might not necessarily be Flash
    that removes it but apparently something does.
    Solution #1: Google "Flash No Audio WAVEMAPPER" for
    directions, its been covered a bunch, but basically requires
    running REGEDIT and readding the WAVEMAPPER key to the appropriate
    location and value in the registry. Its not as difficult as it
    sounds.
    http://weyland.be/wrdprss/index.php/2006/08/22/no-sound-in-macromedia-flash-player-9/
    if your wavemapper key is installed correctly...
    Possible Cause: Corrupted or damaged flash content preventing
    audio streaming from working correctly.
    Soltuion #2: Run CC Cleaner and delete only cached Flash
    content. It is a free program, again just google "download CC
    Cleaner". This particular solution worked for me.
    If CC Cleaner also does not work, the description of your
    problem may differ slightly. In my case on several computers, one
    day it worked, the next day it didnt. If it never worked, this
    would be a logical solution for you. One variation of this that I
    have found is to create a new Windows User Account and log into it.
    The reason the CC Cleaner method may work better is that the User
    Accounts have their own separate cache folders so a corrupted cache
    preventing audio playback on one profile will not be available on
    the other User Account to cause the same problem. I wont explain
    how to do this as the CC Cleaner will work better but if you are
    curious, yet again google "create new windows user accounts". I
    have also seen this method work on one of my affected computers but
    it did not fix the issue on the account I was having problems with.
    http://www.ccleaner.com Install
    and run it, use it only to remove Flash under the Applications Tab,
    Multimedia, Adobe Flash Player. Check it and uncheck everything
    else, then hit Analyze then Run Cleaner.
    Possible Cause: Missing Codec
    Solution #2: Download and install the K-Lite Codec pack.
    Again, google it. A CODEC stands for COmpressor DECompressor and is
    a way to make audio and video files small enough to be transferred
    on the internet. There are a lot of different codecs and if you
    want to play back a video that was compressed using a particular
    codec, you will need that same corresponding codec to decompress
    your media source and view its content. Basically if you dont have
    a codec, you cant observe the content of the media. If you have a
    VCR and want to play back a DVD, you are out of luck unless you get
    a DVD Player. DivX and XVid Codecs are some of the very popular
    codecs used on the net, but to get those, I still suggest getting
    the K-Lite Codec Pack.
    http://www.free-codecs.com/download/K_Lite_Codec_Pack.htm
    Solution #4: Go back to Flash 7. If it aint broke dont fix
    it. This Final alternative is only to be used as a last resort.
    You'll have to get rid of Flash 9 and go back to Flash 7. The
    really tricky part here is that you have to prevent Flash from auto
    updating itself. If you install Flash 7, and hit up YouTube, you'll
    immediately get Flash 9+ installed again with the same problems. So
    AFTER you uninstall Flash 9 (use Macromedias / Adobes uninstaller,
    yet again go google it) make a new text file and name it MMS.CFG,
    in the file put this one line "AutoUpdateDisable=1" (without the
    quotes) and put it in BOTH your c:\windows\system32 AND
    c:\windows\system32\Macromed\Flash folders. This will prevent flash
    from Auto Updating to 9+, then have to find some place to download
    the old flash 7 installer. I found one here.
    http://www.intercomm.com/downloads/Flash7.
    Only problem is that most sites will try to make you install Flash
    9 and Flash 7 does not work on all sites, but it does on some like
    YouTube. DO NOT UPDATE TO FLASH 9+ IF YOU USE THIS METHOD.
    You will probably want to IMMEDIATELY go to
    http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager05.htm l
    after installing Flash 7 and UNCHECK the update feature
    I've tried to write this quick little guide at 3AM so Im not
    going to take more time to research other ways to fix this problem.
    If you have other solutions, such as for MAC and LINUX, or feel
    like adding on to something else that I've written here (links
    would be useful to the downloads I suggested) or correcting any
    mistakes I probably have made, please say so.
    One of these solutions is bound to help you. Theres multiple
    causes for this no audio problem so there is obviously multiple
    fixes.

    http://www.omahapokernews.org
    http://www.holdempokernews.org
    http://www.7cardstudplay.net
    http://www.5cardstudplay.net
    http://www.holdemspot.org
    http://www.texasholdemstate.net
    http://www.texasholdemstate.com
    http://www.pokerbonuslist.net
    http://www.pokerdownloadz.org
    http://www.signuppoker.net
    http://www.tournamentpokerz.com
    http://www.pokercalculatorz.com
    http://www.omahaodds.org
    http://www.omahaouts.org
    http://www.texasholdemrulesonline.net
    http://www.onlineholdemtips.com
    http://www.pokerhilo.net
    http://www.poker-hilo.com
    http://www.hilopokers.com
    http://www.nolimit-holdempoker.net
    http://www.texasholdemlimits.org
    http://www.texasholdemlimits.net
    http://www.onlinepokerlimits.org
    http://www.onlinepokerlimits.net
    http://www.onlinepokerlimits.com
    http://www.texasholdemlimits.com
    http://www.7cardplayer.net
    http://www.5cardplayer.net
    http://www.omahaacademy.org
    http://www.omahapokerrooms.net
    http://www.onlinepokerroomstop.net
    http://www.playpoker-toppokerrooms.com
    http://www.texasholdemz.com
    http://www.playpokeronline-casinos.com
    http://www.texasholdem-vip.com
    http://www.gamble-poker-holdem.com
    http://www.playpoker-holdem.com
    http://www.onlinetexasholdem-poker.com
    http://www.texasholdempokeracademy.com
    http://www.vip-texasholdem.com
    http://www.playfree-poker-online.com
    http://www.texasholdem-pokerrooms.org
    http://www.toppokerrooms.ws
    http://www.toppokercasino.ws
    http://www.onlinepokercasino.ws
    http://www.playpoker-online.ws
    http://www.online-texasholdem.ws
    http://www.play-texas-holdem.ws
    http://www.internet-texas-holdem-poker.ws
    http://www.poker-player.ws
    http://www.luckyschool.com

Maybe you are looking for