How to forward port for remote viewing...?

Since getting a Time Capsule I have been unable to use my SlingBox remotely. After doing some research I figured out that I have to forward a port...but i have no idea how...or what port to forward.
Can someone help me out here?

Use Airport Utility. Click on the Manual Setup button, then click on the Advanced icon in the toolbar. Click on the Port Mapping tab then click on the [+] button to add a new configuration. Use port number 5001 for both TCP and UDP ports in the Public and Private fields. Use the IP address you have assigned to your Airport Express that you've connected to the Slingbox. You will find this all outlined in the Slingbox documentation PDF that came with the device. You can also find it at the Slingmedia website.

Similar Messages

Forwarding port for remote desktop connection

I have been able to connect to my home machine from work using remote desktop. Because of some changes at work I am no longer able to do this on the default port (3389). So I am trying to use port 5190 (which is used for AIM) or port 5050 (Yahoo messenger). Both of these ports are enabled from work and I don't use them at home or on the computer I connect from.
When I changed the port on my home computer, which is connected to a Linksys WRT54G router, I am able to connect when I am on my home LAN using machine_nameort. But when I try my public IP addressort (which is how I would connect from work) I am not able to connect.
I have added a port in the port range forward area of my router. I have tried 5190 and 5050 and both will not allow me to connect when I am not on my LAN.
Any ideas for this?
RIKIL

Actually you don't need to press the reset button for 30 seconds...only 5.
There are two ways to reset the Router’s
factory defaults. Either press and hold the Reset
Button for approximately five seconds, or restore
the defaults from Administration > Factory
Defaults in the Router’s web-based utility.
This is what threw me, I pressed for more than 5 seconds and it wouldn't reset. I had to hold it for about 20 and that worked.

How to use a fixed port for remote assistance in windows 8.1 behind a nat router freebox?

Hello,
Before to use remote assistance in windows 8.1, i need to configure my nat router freebox.
But remote assistance ( msra.exe ) use a dynamique port and never the same.
How to use a fixed port for remote assistance ini windows 8.1 ?
And why i can't use easy connect ?
i read that the router must implement the PNRP protocol. I think it's a propriatary microsoft's protocol unknow on my router.
Thanks

Hello,
Very good. It's a big range ( 255 mini from 49152 ) for a single port but if it's the only one possibility...
You are very helpfull ( i don't know if it's a good english but you make me very happy )
Merci beaucoup

Help networking a Security System DVR for remote viewing

Hey,
I am trying to network my Security System DVR for remote viewing but cannot seem to get it working. I have read some post on this site as well as many others and followed instructions to the T but to no avail.
Here's what I've got:
Linksys WRT54G2 V1 connected to a modem.
My DVR has 3 settings for networking:
-PPPOE
-Static
-DHCP
On DHCP, The DVR automatically sets these settings:
IP Address: 192.168.1.100
Subnet: 255.255.255.0
Gateway: 192.168.1.1
and then the DNS is the same as the one on the "status" area of the router settings...
Port: 10000-10020
I set up port forwarding for 192.168.1.100 for port 10000-10020 selecting "both"
If I pull up the "DHCP Clients Table" it shows the above IP Address but with no name....and the MAC address is something like ee:ee:ee:d4:03:5f.
I have tried to change the DVR to Static and do everything manually but thats not working either.
I created a Dynamic DNS with goddns.org but the DVR seems to have its own one built in that you cannot change. (at the bottom of the network settings it says something like "URL: 123484984.goddns.org----Status: OK." But when I try to type that in the address bar of IE it goes no where.)
I hope someone can tell me why its not working.... It was working when we first got everything set up...then it stopped. then I messed with it and got it working but didn't know what I did. Now its broken again and I don't know what to do.
-Ian
PS. When I am connected to the router via LAN cable and I type the internal IP Address assigned to the DVR by the DHCP (192.168.1.100:10000) it brings up the DVR menu perfectly. But when I try to log into it from a different location...with the external IP address...thats when I have trouble. I do not think my external IP has changed since I got this router set up.
Any help would be awesome.

Hmmm... Did that and I can't seem to get it working still. Whats weird is that as long as I am connected to the router...I can access it through the internal IP address.... (if using DHCP its 192.168.1.100:10000 and if using static its 192.168.1.99:10000)
Those both work when set up on DHCP for the first and Static for the second. But as soon as I type the external IP address with the port it doesn't work. Its like there is a firewall OR the port forwarding is not working. But everything on the port forwarding page looks good... Its enabled, set on Both, correct port range... 10000-10020...
Any Ideas?
-Ian

How to create variant for table/view ?

Hi,
When I go through SM30, I find a radio button called variant. I don't know the effect.
Can anyone tell me how to create variant for table / view ?
I want to know when we need to create variant for table/view.
Best regards,
Chris Gu

hi ,
Whenever you start a program in which selection screens are defined, the system displays a set of input fields for database-specific and program-specific selections. To select a certain set of data, you enter an appropriate range of values.
For further information about selection screens, refer to Selection Screens in the ABAP User's Guide.
If you often run the same program with the same set of selections (for example, to create a monthly statistical report), you can save the values in a selection set called a variant
Procedure
To create a new variant:
       1.      On the ABAP Editor initial screen, enter the name of the program for which you want to create a variant, select Variants, and choose Change.
       2.      On the variant maintenance initial screen, enter the name of the variant to be created.
Note the naming convention for variants (see below).
       3.      Choose Create.
If the program has more than one selection screen, a dialog box for screen assignment appears. The dialog box does not appear if the program only has one selection screen. The selection screen appears in this case.
       4.      If there is more than one selection screen, select the screens for which you want to create the variant
5.      Choose Continue.
The (first) selection screen for the report appears.
If your program has more than one selection screen, use the scroll buttons in the left-hand corner of the application toolbar to navigate between them and to fill the fields with values. If you keep scrolling forwards, the Continue button appears on the last selection screen.
       6.      Enter the desired selection values, including multiple selection and dynamic selection.
       7.      Choose Continue.

How to create EVENTS for a View Cluster.

Hi Tech Gurus,
I have created a view cluster on 5 tables. I need to do a validation and this can be done by using events. But i am unable to create a EVENT for the View Cluster. Could anyone please tell me how to create events for a View Cluster.
Thanks in advance for your esteemed replies.
Regards,
Raghavendra Goutham P.

Hello Pasapula
When you are in the View Cluster maintenance dialog (SE54) click on dialog "Events".
Below the field for the view cluster you have an additional field <b>FORM routines main program</b>. There you have to add the main program containing the FORM routines called by the VC events.
For example: I had defined a normal report containing an include with all the FORM routines. The report contains only the following lines of coding:
report zus_0120_u1.
* Common Data und access routines for user exits in VC maintenance
include LSVCMCOD.
include zus_0120_f1. "FORM routines for VC events
Now in the "Events" dialog of the view cluster maintenance you assign your FORM routines to the events.
Regards
Uwe

How to Network Interface for Remote Debugging in Adobe Flash Professional CS6?

How to Network Interface for Remote Debugging in Adobe Flash Professional CS6?

Check out : http://helpx.adobe.com/flash/using/whats-new-cs6.html
In that click on "Choose network interface for remote debugging for AIR" section.
Hope it helps.

How to forward ports using Airport Extreme?

So,
I wanna forward some ports but every guide I find on the internet describes how to use the Airport Admin Utilty to do this. The problem is though that I can't configure my AE using AIrport Admin Utility; I need to use my Airport Utility instead. The only problem is that I don't know how to forward ports using Airport Utility.
Anyone?

In AirPort Utility, Port Forwarding is called Port Mapping which is under the Advanced->Port Mapping tab.

How to download applet for offline viewing!!

How to download applet for offline viewing!!

View source on the web page containing the applet. It will point ot a file.class
Then change your URL to that file and it should download it.
Lucas

Forwarding UDP port for Remote Desktop Gateway

What is the correct way to forward UDP 3391 port for RDG server?
What direction should I choose for UDP port parameters? "Receive" or "Receive Send" or something else?

Aurimas N, Were you able to get RemtoteFX working through TMG? I have the same issue whre I can not get UDP working with clients conneciting over the WAN. Can you tell me specifically how you got this to work on your TMG?
Thanks
I am not sure how to check to be honest, on TMG I only see 443 port being used, and since it is remoteApp there is no connection indicator, or I don't know how to access it.

How to: Setup AAE for Remote Disk Access & Serve PS3

Hi there,
I've read so many tutorials, and tried so many combinations, but haven't found anything for my specific purpose.
I was wondering if someone might have the insight to do a quick run-through (including specific settings) on how I would setup my Airport Extreme for the following scenario/purpose.
Setup:
1. Netgear DGN2000 ADSL Modem + Router in one
2. Airport Extreme = Model #A1354
3. Western Digital Studio 1TB (mac os extended journaled formatting - not used as time machine)
4. PS3 80gb
*To accomplish:*
1. Access the Western Digital HDD remotely. So I can access my files from work.
2. Use the Western Digital HDD to serve media to the PS3 when I'm at home, so I can watch movies without having my computer turned on.
Caveat:
1. I don't want to use/pay for MobileMe.
Many thanks,
Glen

Hello nelga. Welcome to the Apple Discussions!
Since most of your questions are not really AirPort networking related, I will do the best I can to provide assistance.
1. Access the Western Digital HDD remotely. So I can access my files from work.
I know you don't want to use BTMM, but to best understand the hurdles you will be up against, it might be worth taking a quick look at how BTMM works "behind the scenes" to allow you to access a HDD remotely.
BTMM - Basic Communication Flow
o For a computer connected to the Internet via a router, BTMM "asks" the router for its configuration information. For a router, like your AEBSn, that uses NAT-PMP, BTMM will ask the router to assign arbitrary public ports. In turn, the router will provide these port assignments (& the router's Public IP address) back to BTMM.
o BTMM then sends this information to the MobileMe account. In background MobileMe updates a special set of DNS entries to be used by BTMM. These entries are then made available to all BTMM clients using your MobileMe account. When a computer, with BTMM enabled, uses your MobileMe credentials, it automatically retrieves a list of all other computers/routers that are registered with the same account. All these devices should then appear under the SHARED section of the Finder.
o When attempting to connect to a remote computer (or router), BTMM creates a secure connection to that remote device using the information from the MobleMe account.
o Once the connection is established, the devices can then communicate with each other.
The key to all this is that you will need the following in order to be able to remotely access the HDD:
1) Your ISP must provide you with a publicly reachable IP address.
2) If your ISP provides you with a Dynamic (vs. a Static Pubic IP address), you will need to keep track of that IP address in order to consistently have access to the HDD. Without knowing this address, when your ISP changes it periodically, you will have to manually "retrieve" it to connect again. You can get around this by using a service, like DynDNS.
3) You will have to configure your NAT router for port forwarding/mapping to allow the necessary file sharing communication to pass through the router to the AEBSn with the shared HDD. Specifically you want to open the appropriate ports for both the AFP (TCP: 548) & SMB (TCP: 445) file sharing protocols.
4) Similarly you want the AEBSn to be enable for file sharing.
2. Use the Western Digital HDD to serve media to the PS3 when I'm at home, so I can watch movies without having my computer turned on.
In order to stream video from your WD HDD, you will need a DLNA-compliant Media Server to stream that data to the PS3, which is a DLNA client. With that said, you will need at least one computer (Mac, PC, or Linux-based device) running in order to run this server. The WD HDD has no means to run this server as it has no operating system.

How to Open Ports for HP Printers for all computers within the network (router)

Hi,
I have the EA6700 router and a few HP printers and Multi purpose printers/scanner/fax ...
When installing the print drivers, they are ok. Sending to printers are not a problem. However, the problem comes with scanning.
The HP Software ask to open a port for it... How do I do that? I checked, it seems other computers are affected by it too after changing to this new router.
I read that it can be done on the "App and gaming" section at the Security page. Do I go to the port forwarding section? But it only forward to one computer. that doesn't work...
I'd like to open a port and a lot of other IPs can print and scan from it.
Thanks

Ports are not needed to be opened on the LAN side of the router for Printers and Scanners. I recommed that tiy contact hp for help and information regarding setup and configuration of those devices. Also the addition of a external Gb network switch for these devices is recommended as well. Would help eliminate any un-necessary router configuration or processing.

How to change Port for SAP Client on SAP R/3 Server?

The defualt port for SAP GUI Client is 3200.
How could I change the SAP GUI Client port to say 5222 instead of 3200?
How can I view the full list of all ports required by SAP R/3?

Freddy,
I don't have the document handy but there was a document on service.sap.com/security which would give you a list of all the ports. SAP's wording is some thing like "specific ports are fixed and SAP does not support changing that port number".
In case of GUI client and your example of 3200, as you know 00 is based on the fact that that is your instance number. You could change last two numbers by assigning a different instance number (and not 00).
Thanks
BMG

Right for Remote View Only?

I am using ZfD3.2sp2 with ConsoleOne 1.3.5 or 1.3.6. I have a Help
Desk
that I would like to grant Remote View of a group of workstations. I
am
able to remotely control workstations as administrator. I have
checked
Remote Operator tab and the users show with Remote View and I have
granted
read right to the WM:Network Address property and write to the DM:ZEN
Remote View property of the Workstation object. I am able to ping the
workstation but receive a failure due to rights issue.
Can anyone tell me what rights I really need to allow a non-admin the
ability to RC a workstation?
Thanks,
Rob Bennett

Rob,
How about this one?
http://support.novell.com/cgi-bin/se...?/10087662.htm
Also, there is wizard that does this for you under c1, tools.
Jared L Jennings, CNE
Novell Support Forums SysOp.
http://support.novell.com/forums/faq_nntp.html
Posting with XanaNews Reader 1.15.8.4
Geek by Nature, NetWare by Choice.

Forwarding port for Counter-strike: Source is not working

With my linksys router (Model WRT54G)I tried forwarding my port for a Counter-Strike: Source server. My friends tried it after I tried forwarding the ports and it did not work. It looks like this: |Application|Start|End--|Protocol|Ip-Adress------|Enabled| |CS1--------|1200-|1200-|Both----|192.168.1.[105]|Check--| |CS2--------|2700-|27015|Both----|192.168.1.[105]|Check--| |CS3--------|27020|27039|Both----|192.168.1.[105]|Check--| I can get on the server but my friends can not. And yes, I did uncheck "Block Anonymous Internet request". Message Edited by Iridium on 08-16-2007 07:37 PM Message Edited by Iridium on 08-16-2007 07:38 PM
Message Edited by Iridium on 08-16-2007 07:38 PM

Is the IP address 192.168.1.105 really the IP address of the server in your LAN?
Moreover, check what kind of modem you have. Follow the instructions here. If the IP address on the status page is a private IP address and the IP address on whatismyipaddress.com is different then your modem does routing too and you have to configure port forwarding there as well.

How to forward port for remote viewing...?

Similar Messages

Maybe you are looking for