How to Gatekeeper on cisco 7200

How can i enable my gatekeeper on cisco 7200 my current IOS is 12.1.(2)T i cannot enable my gatekeeper it seems to be working before.
hope you can help me.
thanks

Does rolling back to previous version help. If so you could search for any potential bugs in 12.1.(2)T or try loading the latest version.
My search on bug toolkit with "Gatekeeper" keyword on this release got me 240 bugs. I am not sure which one is yours. So better try with the latest version

Similar Messages

  • GETVPN Key server Cisco 7200

    Hi,
    I am using Cisco 7200 NPG1 as Key server for GETVPN. I have almost 500 Spokes. How many concurrent IKE sessions could be supported by 7200 box ?
    I have heard that simultenous session limit for IKE is 100 ?
    regards
    Prasad K

    I have heard that simultenous session limit for IKE is 100 ?
    This is true to software crypto.
    You get best scaling factor on 7200 with VSA. 500 seems a decent number. Are you seeing any problems?

  • How to check if Cisco WSA is already blocking the malicious sites?

    How to check if Cisco WSA is already blocking the malicious sites? 

    Depends on what you mean, but in general what you did will not work.
    The usual intent of RMI is to have several processs running and all of them use one process as the repository.
    A static value is only visible in one VM instance thus it will not be visible in another process.
    So in that situation you could check if the the server socket that the RMI using is open. But just catching the exception, presuming that you catch the correct one, is also sufficient.

  • How do I get Cisco Connect back?

    I bought the Linsky E2000, and after I installed it Cisco Connect was installed too. Someone in my household uninstalled Cisco Connect so now my Linsky gaming adapter wont work so my laptop and PS3 can't go on the internet. How do I get Cisco Connect back?

    I gave up on Cisco Connect the same way I did the stock E300 firmware, so it's now moot to me. The one thing I found with the Connect software was that if you make a change to the router setup from the web interface, Connect lis likely to no work anymore.
    I was able to get it back a couple of times by changing the XML config file on *all* the machines. Most of the connect testing period, I wound up doing a 30-30-30 reset on the router and reconfiguring from scratch. No more, since I went to TomatoUSB.
    FBIG a.k.a. BezantSoft
    SOHO Network: E3000 TomatoUSB (1.28.7440 MIPSR2-Toastman E3000 USB Ext); WRT54G (Base Tomato 1.28.1816) as AP; Belkin 150 N+ Gbit Storage Router; HP [email protected] 64bHT W7(32bit)Ult & WinXP Virtual instance. HP [email protected], XPProSP3. IBM [email protected] XPProSP3. DIY P4 [email protected], W7Ult32. HP [email protected], XPProSP3, w 100M, 802.11G, builtins 1G PCMCIA & WUSB600N addon Nics. all running NM 5.5.9195.0-pure0.beta. Hawking PrtSrv 100M to USB. Offline: BEFW11S4, WRT54GC, ADSTech NAS 100Mx500Gb. Son took Xbox360 to college. {sniff!}

  • Multilink limitations application on Cisco 7200 Series

    Hi,
    Can someone please mention if Multilink can be supported on Cisco 7200 Series?
    IOS version:
    IOS 7200 Software (C7200-P-M), Version 12.3(16a), SOFTWARE (fc2)
    cisco 7206VXR 
    Any comment will be appreciated.
    Thank you.

    Hi -
    Our s/w development group is in the process of implementing ipv6 support in our products, and would like to use our Cisco 2650XM running ITP s/w for ipv6 interoperability tests.
    However, it appears that ipv6 is not supported in this s/w version:
    ITP1#sh version
    Cisco IOS Software, C2600 Software (C2600-ITPK9-M), Version 12.4(15)SW2, RELEASE SOFTWARE (fc3)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Tue 23-Sep-08 19:48 by prod_rel_team
    ROM: System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1)
    ITP1#config
    Configuring from terminal, memory, or network [terminal]?
    Enter configuration commands, one per line. End with CNTL/Z.
    ITP1(config)#ipv6 ?
    % Unrecognized command
    My question is: Can I use this s/w version on the 2650XM in an ipv6 network? Do I need to upgrade the s/w?
    Thanks,
    Matt

  • Building Cisco 7200 VXR

    Hi,
    I have a Cisco 7200 VXR chassis. What cards I have to buy to mount a VoIP Gateway, with SS7 E1 ports to trunk with the PSTN networks?
    Best Regards.

    You can use Cisco MIX-enabled T1/E1 Port Adapter. For more information kindly refer the url's below,
    http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00800afd65.shtml
    http://www.cisco.com/en/US/products/hw/modules/ps2033/ps1952/index.html

  • Cisco 7200 as managed cpe with mpls enabled

    Is there any real network that is using managed CPE (CPE router managed by SP) with mpls enabled (MPLS-TE, VPN) etc.
    Is anybody using cisco 7200 as a managed cpe router with mpls.
    Thanks.
    subodh

    with PE router, Service provider handles so many CE routers (of customers).
    Managed CPE router will be placed at the customer site and will handle only one customer.
    Is there any company/customer that have so big network that they need cisco 7200 at there site and this CPE does MPLS-TE,MPLS-VPN.
    could u pl. name some companies that are availing this king of services from service provider.
    {as cisco 7200 is also capable of providing voip solution to customer}.

  • Cisco 7200 as BRAS

    Hi,
    does anyone of you know if you can use a Cisco 7200 as a BRAS? We were told it is possible, but I am not able to find an IOS image with PPPoE support.
    Any pointers are welcome.
    TIA
    NaNa

    As far sa I know, you can get ISG
    (http://www.cisco.com/en/US/products/ps6566/products_configuration_guide_book09186a008061ab53.html)
    features on 7600 platform but only for IP sessions, not for PPP.
    These functions should be available on on SIP-400.

  • How to factory default cisco MDS 9222i

    How to factory default cisco MDS 9222i

    Hi,
    write erase
    write erase boot
    reload
    (If prompted to save run to start, say no)
    http://www.cisco.com/en/US/docs/switches/datacenter/mds9000/sw/4_1/configuration/guides/cli_4_1/bb.html#wp1087208
    Regards,
    David

  • Hello, can someone tell me where i can find a document how to upgrade a cisco 6880 running vss

    I copied the ios to bootdisk, but when I change the boot system and reload my standby peer de standby peer starts up in rommon mode. I need the correct parameters for the boot command for a 6880. On the cisco site I can only find how to upgrade  a 6500 with vss,but I need the documentation how to upgrade a cisco 6880. Can someone please help me to find this . Thank you.

    There are several methods.  Both methods has downtime.  One method is FSU/eFSU, which I will NOT go into, is an "automated" method of upgrade.  The automation, if it works, include booting each chassis one at a time.  
    The second method works well for me.  Before I begin, it is very, very important that you check the MD5 hash value of the IOS file you've downloaded against the MD5 hash value found in the Cisco website.  
    1.  Copy the IOS to the sup-bootdisk:.  
    2.  Copy the  IOS to the slavesup-bootdisk:
    3.  Change the boot variable string to point to the IOS of your choice.  Additionally, you can specify a second boot variable string to point to your OLD IOS.  This is very handy/important if your chassis attempts to boot the new IOS you've copied and failed.   It is important to remove the old boot variable string before changing.  
    4.  Ensure your config-registry is 0x2102.  
    5.  Save the config first and copy the startup-config to an external media:  CF or TFTP
    6.  Reboot the chassis. 
    Hope this helps.

  • Cisco 7200 VSA issue after upgrade to IOS 15.2

    After upgrade to IOS 15.2(4), VSA module in 7206VXR (NPE-G2) is disabled and we cannot enable it.
    Show diag output:
    ------------------ show diag ------------------
    Slot 0:
    VSA IPsec Card Port adapter
    Port adapter is deactivated
    Port adapter insertion time unknown
    EEPROM contents at hardware discovery:
    PCB Serial Number        : JAF1309ADDT
    Hardware Revision        : 1.0
    Part Number              : 73-10220-05
    Board Revision           : B1
    RMA Test History         : 00
    RMA Number               : 0-0-0-0
    RMA History              : 00
    Deviation Number         : 0
    Product (FRU) Number     : C7200-VSA          
    Version Identifier       : V01
    Top Assy. Part Number    : 68-2578-05
    CLEI Code                : CNUCAFNAAA
    EEPROM format version 4
    EEPROM contents (hex):
      0x00: 04 FF C1 8B 4A 41 46 31 33 30 39 41 44 44 54 40
      0x10: 05 0D 41 01 00 82 49 27 EC 05 42 42 31 03 00 81
      0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 43 37 32
      0x30: 30 30 2D 56 53 41 20 20 20 20 20 20 20 20 20 20
      0x40: 20 89 56 30 31 20 D9 03 C1 40 CB 87 44 0A 12 05
      0x50: C6 8A 43 4E 55 43 41 46 4E 41 41 41 FF FF FF FF
      0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
      0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
    If we try to enable it manually from CLI we get the following message:
    Router(config)#crypto engine slot 0
    VSA will NOT come up until system power-cycle or reload
    Of course, after reload nothing happens.
    Is VSA incompatible with IOS 15.x? I'm asking because downgrade to 12.4 causes VSA to be active again.
    Regards,
    Igor

    Hi igor,
    1) FDP image
    Field-programmable devices (FPDs) are hardware devices implemented on router cards that support separate software upgrades. An FPD image package is used to upgrade FPD images
    The FPD image package must be compatible with the Cisco IOS software that is running on the router. If an incompatibility exists between an FPD image package and the Cisco IOS software release running the router, the device with the FPD will not operate properly until the incompatibility is resolved.
    The FPD automatic upgrade feature searches only for the FPD image package file that is the same version number as the Cisco IOS release being used by the system. For example, if the Cisco IOS release being used is Cisco IOS Release 12.4(5)T1, the system searches for the FPD image package file that supports the specific Cisco IOS release (c7200-fpd-pkg.124-5.T1.pkg).
    2) Steps to Upgrade:
    From the document below which I already sent you, please refer to the section “How to Upgrade Field-Programmable Devices”
    http://www.cisco.com/en/US/docs/routers/7200/configuration/feature_guides/fpd.html
    I would recommend you to follow the steps in the “Field-Programmable Device Quick Upgrade (Automatic FPD Upgrade Only)” as that is the recommended and the easiest way.
    Steps are:
    The command is present “upgrade fpd auto” in the running-config by default.
    Have the Cisco IOS image in disk2:
    Download the FPD image package to disk2: flash disk
    Reboot the router using the new Cisco IOS release.
    Hope this helps
    Thanks
    Syed

  • How do I use Cisco Registered Email Service with 10.7?

    I received a email via someone using Cisco Registered Email/Envelope Service.  The authentication process required the latest version of JAVA for 10.7, which I downloaded and installed.  When I try to logon, the screen hangs with the message "Loading Envelope Tools."  If I press "open" again it states "Inactive tools."  The alternate method is to open the mail via a secure Web site, which I can open, but I am unable to download attachments.  To download attachments, I am directed to a page that begins with "x-msg:" and I get a message that says: "Safari can't open the address .. . because MAC OX doesn't recognize Internet Addresses starting with "x-msg:"

    Thanks for the info Roger, this is indeed did work for me (at least the part about signing in on apple.com, haven't tried the rest). Since Apple does not allow for the merging of Apple IDs, my plan is to use the old me.com address (from the free trial) with iCloud but then forward all the messages from the old me.com to my current Apple ID. Problem is all my devices are already associated with iCloud. So... if I want to activate iCloud using the old me.com, how do I do it?
    I have two ideas: 1) as you suggest, signing out and signing back in through the iCloud preference pane (either on Mac OS or iOS); but I'm worried this will have consequence - will I be able to sign back in to my main Apple ID account after doing this?
    2) create a new user on my Mac and then sign in to iCloud with the old me.com address there, then delete the account.
    Thanks for any help with this.

  • How do I install Cisco Connect without the CD-Rom?

    I want to add a password to my router. I no longer have the cdrom. I own a mac. I saw firmware and a wizard to download on the linksys site but it was only for a pc. can I download from online for a mac? or does it have to be done on a pc? or should I request a new cd-rom? and if so how?

    I found the Linksys web site for you.  Then I did a simple search and found the software for you also.
    Go here..
    http://homesupport.cisco.com/en-us/wireless/linksys/E3000
    Select download then version 1.  You will see the software for the MAC.

  • How do I delete Cisco connect w/o the software?

    I installed Cisco Connect about 8 years ago. Since that time, my router died, and I installed a new router. Also in the interim I completely discarded all of the software, as I had though, I had properly removed all remnents of it on my imac. Recently out of the blue, I have been recieving the message, please enter your "Cisco Connect guest password," several times a day. I don't know it, and certaintly don't need to enter it, since I am using a new router. How do I remove this intrusive software, from my computer.

    Thankyou Jane, I'm an idiot. According to my network connections it turns out is my network, and I never replaced my router. Still I only use the main network, and never the guest network. I looked for the software, that came wt my router, and can't locate it anymore. That is why I thought that it was a new router. Still I don't have any need for the guest network. I couldn't figure out how to just delete the guest network. So I took a chance and removed all of the WiFi networks. I'm not exactly sure why, but my main network still operates on my device. Also my Bluray player is still able to access my main network. My computer and blue-ray might be working on my Xfinity WiFi, but the main network still displays on my sevice. Hopefully my computer doesn't ask me for the guest password anymore.

  • How often should the Cisco 6509 and 3750 switches be rebooted? Does Cisco have a best practice recommendation?

    How often should the 6509's and 3750's switches be rebooted?
    Does Cisco have a best practice document on this and recommendation how long the switch should be up before it gets rebooted?
    Why is a reboot needed if there are no indications of issues on the log?

    I'd agree with Larry here.
    If you're not seeing any issues with your IOS revision and there are no relevant PSIRTs (security notices applicalble to features and or exposure of your device requiring an IOS upgrade) then you can go a very long time without rebooting, if ever.
    I'm sure it's far from a record, but our corporate distribution router that supports >1000 downstream devices day in and day out has never been rebooted since installation just over 5 years ago. I have a top of rack Layer 2 switch (2900 series running CatOS) that's almost at 10 years.
    That said, you should have some monitoring scheme that assures you everything is healthy. But as long as memory and cpu are happy, the device will run forever.

Maybe you are looking for