How to generate biphasic pulses and change parameters?

Hi I am a beginner. I need to know how to generate biphasic pulses. What are the functions i need to use(the logic involved in labview to generate)? I should be able to change the parameters like duration,interval during the course of the program.

Greetings:
You can go to the Analysis/waveform/signal generation toolbox and find Pulse Pattern. You can set the duty cycle, frequency and phase with the standard controls.
Eric
Eric P. Nichols
P.O. Box 56235
North Pole, AK 99705

Similar Messages

How to generate TDS certifcate and CHallan forms

Hello All,
How to generate TDS cerficates and challan forms for Pakistan withholding tax in ECC system,
Regards,
Ramana

Hi,
Check whether you have activated Withholding tax for your company code and country. Each country has
its own versions like India has Country India Version. Check with SAP the version for Pakistan whether
there is any country specific functionality. Ofcourse, you can use the other versions if the same
parameters suits the tax classification if your country.
Regards,
Sadashivan

How to generater automatically getters and setters???

Hi!!!
Boys and Girls, how to generate automatically getters and setters like eclipse dialog or shortcut, using bea workshop(jpf file)?
Best Regards,
Pablo

can anyone tell where i can find libraries for access/manipulate beans.
and sample example to invoke getters and setter of the property but not like preparing String "setPropertyName" or "getPropertyName" and invoking the method i beleive there should be standard way
and also setPropertyName may take different type parameters i cannot keep number of if conditions to check for different datatypes
with regards
satya

How to generate pwm pulse using NI DAQ in MATLAB

hi everyone. please tell me how to generate pwm pulses using Ni DAQ card in MATLAB Simulink. if through coding is possible then post the corresponding code.....reply me

Make sure you have installed the Measurement studio support for VB 6.0 then you will be able to find examples in the folder below on win7 and 8.
C:\Users\Public\Documents\National Instruments\NI-DAQ\Examples
Narrow down to Analog Output and choose update voltage example for measurement studio.
You also have the possibility to use DAQ assistant if you have measurement studio installed. This function is a configuration type programming. After going through the configuration Wizard code is automatically scripted for you so that you can output the voltage you need. Read more about DAQ assistant in the blow link.
http://www.ni.com/white-paper/4652/en/
Best Regards
Jonas Mäki
Applications Engineering
National Instruments

How to Generate Synchronized pulses across two separate cards on a PXI system

Hey,
I'm trying to generate three pulses from my PXI System for triggering purposes. I have two cards (PXI 6259 and PXI 6115) , each with two counter/timers on them. The 6259 has 32 bit timers, and the 6115 has 24 bit timers.
Up until now, I only needed two pulses. One was 180us long at 20 Hz, and the other is 5us at 20 Hz, starting 150us after the beginning of the first pulse. I was able to achieve this by generating both pulses on my 6115 card by triggering the shorter pulse off of the rising digital edge of the longer pulse and giving the DAQmx Counter/Timer task an initial delay of 150us.
The third pulse needs to be identical to the short pulse, only it needs to occur 20us early (130us after the start of the wide pulse). I tried to generate it using the same technique as I used when generating the short pulse, only generating the pulse and reading in the rising digital edge trigger on my 6259 card instead of the 6115.
The result was that my pulse trains were asynchronous and the pulse generated on the 6259 card was constantly shifting to the left.
This puzzled me, so I wrote up a little dummy program to test generating triggered pulses. The results were that when I generated two pulses on the same card, they were always synchronized; however when I generated pulses on separate cards, one of the pulses always shifted.
I was hoping somebody could suggest a reason that the pulses across cards are asynchronous even though I'm reading in a digital trigger and hopefully a way to rectify the situation and synchronize all of my pulses.

The problem, in a nutshell, is that the timebases on the two boards have manufacturing tolerances that will cause them to differ from one another. The accuracy error is a small fraction of a percent, but the effect on the phasing of your pulses will be cumulative. That's why you saw the one set of pulses "shifting to the left."
The solution is to make sure each board derives its pulse timing from a single common timebase. Fortunately, this is pretty easy to specify with DAQmx, just a little tricky to find. In the chain of VI's you call to configure the counter pulses, insert a DAQmx Channel property node. From memory, I *think* you should be looking under something similar to "Counter Output->General->Timebase->Timebase.Src"
Right click and create a constant or control to define the timebase source. You should get a dropdown list that includes a wide variety of choices. Among them are each of the boards' 20 MHz clocks. By default each task will use a timebase from its own board but this technique lets you route one board's timebase over the PXI backplane with that single property node setting. DAQmx does most of the dirty work behind the scenes.
-Kevin P

How to reverse from quality and change the vendor account.

I had made GR, but posted wrong entries, instead of doing one vendor account & i had made in other vendors account, this lot is passed by quality also that means it UD is also done.
how to reverse from quality and change the vendor account.
Thanks and Regards

hi Raj,
Reversing Stock Postings Locate the document in its SAP Library structure
   1. Choose Logistics ® Materials Management ® Inventory Management ® Goods Movement ® Goods receipt ® For purchase order ® PO number known.
The initial screen for creating a goods receipt for a purchase order appears.
   2. In the field for the movement type, enter
   3. 102 (goods receipt for a purchase order into warehouse - reversal). In the field for the purchase order, enter the purchase order number for the original goods receipt.
Note
You can copy the purchase order number from the inspection lot.
   4. Choose Enter to display the selection screen for the purchase order items.
   5. Select the purchase order item for which you want to create the goods receipt and set the Stock type indicator to the stock to which the goods were originally posted with the usage decision (for example, F for unrestricted-use stock or S for blocked stock).
   6. Save the goods receipt and exit the Materials Management component.
   7. Choose Logistics ® Quality management ® Quality inspection ® Inspection lot ® Usage decision ® Change with history.
The initial screen for changing a usage decision appears.
   8. Enter the number of the inspection lot for which you previously made the usage decision and choose Usage decision (UD).
   9. To cancel the inspection lot, choose Usage decision ® Functions ® Cancel lot in the usage decision screen.

Urgent!! How to update Planning book and change when planning will start

Hi Gurus,
I had configured the system and we can initilize planning area every month and my question is
1. How to update planning book and change planning start date every month?
Thanks a Lot
Regards,
Raj

Hi,
In the planning book-dataview, you will assign the time bucket profile, and will be on rollling basis. if you want the forecast profile on rolling basis, maintain the forecast and history horizon as periods then that will also be on rolling basis.
Regards,
Raj

When opening a new tab, it opens onto a search engine, which is not what i want it to do. How do i resolve this and change it back to just a black page?

when opening a new tab, it opens onto a search engine, which is not what i want it to do. How do i resolve this and change it back to just a black page?

A new tab opens by default as a blank tab (about:blank).
If that isn't the case then an extension has changed that behavior.
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.org/kb/Safe+Mode

HT4623 Bought Iphone Off of craiglist and it is not an att product the iphone had a gci sims card in it . How do i unlock phone and change carriers

Bought Iphone Off of craiglist and it is not an att product the iphone had a gci sims card in it . How do i unlock phone and change carriers

You contact the carrier it is locked to.
Unfortunately, if it's actually a GCI phone, they do not offer unlocking.

I've never made a rescue email, how do I make one and change my security questions

I've never made a rescue email, how do I make one and change my security questions

Click here for information. If you can't reset them through the method described in that article, contact the iTunes Store staff via the link in the 'Additional Information' section.
It isn't possible to create a rescue email address without correctly answering two of the questions. Nobody on these boards can reset them for you.
(95613)

How to generate pdf report and automatically save in the folder?

Hi all,
I want to ask, how to generate pdf report and automatically save in the folder?
Actually, if i run pdf report and show to screen. Now do not need to show to the screen but save the pdf file in the folder.
If anyone know, please share to me.
Thanks and regards,
Iwan

Hi all,
Thanks for the reply.
when i run pdf report, and i got this URL to show the pdf report.
http://190.180.55.73:7778/reports/rwservlet/getjobid3828?server=sitcnrepsvr
Do any body know where can i get this pdf report that i have run in application server report folder ?
Thanks and regards,
Iwan

How to generate a pulse train with different pulse width and delay?

How to generate a triggered pulse train with different pulse width. for example, after each trigger signal, let's say 2 ms, then the counter output a pulse with pulsewidth of 1 ms, and then after 3 ms delay after the first pulse, the second pulse was generated with a pulse width of 4 ms. Next cycle when the trigger signal comes, the same two pulses will be generated and so on. Is it possible to achieve this by using 6601 counter card? and if yes, how to achieve this? Thanks!

Unfortunately you can not create a hardware timed pulse train with different widths on each pulse from a counter. Whilst it can be changed on the fly using software, since you require a hardware triggered signal getting the software involved will not give a huge amount of accuracy when the pulse will actually change.
So in short you can't use your 6601 card (or a counter timer) to achieve this
There are three possible Alternative solutions
1 You could use a high speed digital IO device such as the (6533/34) to generate your variable signal which would require setting up the pulse train as a series of states based around the burst transmission mode where the clock would give you your specific timing.
2 A timed analogy output (for example on a MIO card with a clock (PCI-6220 / 62xx), i.e. Not the 6704 style static analogy output cards)
3 A high speed digital waveform card such as the (, 656x , 655x, 654x, 6534, 6533 (http://www.ni.com/modularinstruments/find_right.htm) ) this could then be scripted to work with your triggering and also there is a digital waveform editor which will enable you to set up the pattern you wish to generate (http://sine.ni.com/nips/cds/view/p/lang/en/nid/13555)
Hope that helps
Tim Matthews
NI (UK)

How to generate a pulse waveform 90 deg phas shifted with respect to a pulse generated using a counter in PXI 6070E daq card ?

Hi
I ma using 6070E daq. I am generating a infinite pulse train using one of the counters. I want to generate another pulse train which should 90 degress phase shifted with respect to the previsously generated pulse. How to implement this using the counters in the DAQ card.

Hi Gopal,
1) yes the frequency generator is programmable. You have 2 timbebases (10MHz and 100kHz) and you can divide down by any integer between 1-16. Those are the only frequencies you can use.
2) The way counters work is that you can apply a gate signal to the counter which will cutoff the output. Therefore, you can have a second counter generating a pulse train of an equivalent frequency to the frequency generator (fout) but you don't want it to start immediately. You want it to start only after a short delay (equivalent to a 90d phase). Therefore, you need to "gate" or prevent the output on this counter for that small delay period of time. The way you can do this is by using a second counter to create a delayed pulse. You would
connect the output of that counter to the gate of your pulse train function. That way, during the delay period of the pulse, you won't be outputing your pulse train yet. When the pulse (high-time) of your pulse reaches the gate, then your pulse train will start generating its pulse train (which is consequently delayed by the amount of delay used in the single delayed pulse counter). Since you don't want your pulse to go back low, you will have to turn off or clear your pulse counter while it is high. That way the signal on the gate will remain high forever.
Your better solution is to use a PCI-660x card to perform this action. You will have more counters which will give you a greater range of frequencies to choose from and you will have more accurate timing of the signals.
Anyway, hope that clears things up. Have a good day.
Ron

How to generate a pulse on x number of events PCI-6602

I am running LabVIEW 5.1 full development with a PCI-6602 counter board.
I would like to generate an output pulse after counting x number of input pulses. I would also like to reset the counter with an external signal.
My application is I am trying to generate a second index pulse for an encoder.
I would like to count the pulses from encoder phase A and generate an output pulse on x number of counts. Then I would like to reset the counter using the encoder’s index pulse. This way I can change the phase of the “generated” index pulse with respect to the “real” index pulse by x number of counts (degrees) and maintain that regardless of encoder rpm.
Thanks
Brian

Brian,
There actually is a way to do what you want, but it gets a little complicated. I don't have LV on this machine so I'll have to just describe the idea. First a summary: the counter will repeatedly countdown to 0. Each time it reaches 0, it will generate a brief pulse which will in turn hw-reset the counter value to N. Then it will countdown to 0 again, etc. The same brief pulse could also be wired to a different encoder-measuring counter to create a "delayed" reset to 0 (or some other #).
1. Configure your counter for "position measurement" instead of "simple event counting". Set the encoder type to, um, I forget the name -- something like "two pulse encoder." It's the setting that will increment with every SOURCE edge and decrement with every AUX edge. Wire your encoder channel A to the counter's default AUX input (in position encoder mode, you must use the default input pins). Hard wire from the default SOURCE input to GND. Now every encoder edge will decrement the count, and nothing wlil ever increment it.
2. Configure the counter to use z-indexing. Set the z-index reload value to be N-1, where N is the # of encoder counts by which to delay the encoder's real z-index pulse. Set the z-index reload phase appropriately, probably to A low B low. Wire the real z-index pulse to the counter's GATE input.
3. Configure the counter to "pulse on terminal count" -- you do this using 'Counter Set Attribute.vi'. So N encoder edges after the real z-index pulse, you'll generate a pseudo-z-index with this counter.
4. You can wire this pseudo-z-index to the GATE input of the encoder-measuring counter. Now the encoder's z-index pulse is delayed by an amount you can program.
5. Note: this method requires the motion to be uni-directional.
Good luck!
-Kevin P.

How to generate a pulse with 9472?

I am trying to generate a single 8V pulse of 10ms duration on multiple channels of the 9472. The 9472 is in slot 4 of the 9172 compact daq chassis. To test my results, I have connected an oscilloscope to one channel of the 9472 (with no load attached). I tried modifying the Create Digital Waveform VI from the Write Dig Chan-Ext Clk example VI. In doing so, I generated a binary array with the first half of the array filled with all 0's and the second half of the array filled with all 1's. When I triggered my O'scope on a rising edge, I saw the channel turn on (also the LED was lit on the 9472). However, the channel stayed on even after the routine had completed (LEDs were lit solid). So to try to turn the channel off, I appended one 0 to the end of my array. Now the O'scope won't trigger and I see no sign of the LEDs on the 9472 blinking. Any ideas how I can solve this problem?
I was able to get a single pulse of the proper duration by setting up a task in MAX with the 9472 in slot 5. But in doing so, I was only able to generate the pulse on one channel. I need to be able to parallel multiple channels for my application.

I am trying to generate a single 8V pulse of 10ms duration on multiple channels of the 9472. The 9472 is in slot 4 of the 9172 compact daq chassis. To test my results, I have connected an oscilloscope to one channel of the 9472 (with no load attached). I tried modifying the Create Digital Waveform VI from the Write Dig Chan-Ext Clk example VI. In doing so, I generated a binary array with the first half of the array filled with all 0's and the second half of the array filled with all 1's. When I triggered my O'scope on a rising edge, I saw the channel turn on (also the LED was lit on the 9472). However, the channel stayed on even after the routine had completed (LEDs were lit solid). So to try to turn the channel off, I appended one 0 to the end of my array. Now the O'scope won't trigger and I see no sign of the LEDs on the 9472 blinking. Any ideas how I can solve this problem?
I was able to get a single pulse of the proper duration by setting up a task in MAX with the 9472 in slot 5. But in doing so, I was only able to generate the pulse on one channel. I need to be able to parallel multiple channels for my application.

How to generate biphasic pulses and change parameters?

Similar Messages

Maybe you are looking for