How to get a N network running with iphones in the house??

Hi there
I have 3 x Airport express (N) stations, 1 x single port ethernet adsl2 modem.
My problem is this,
I want to create a 5ghz N based 300mbps network for our 2 macbooks in the house. We also have 2 iphones in the house. When I create the 5ghz band, the iphones can't see the network. I am only using 2 of the stations, using the "extend my network wirelessly" mode. I have a spare airport that I can add to the mix if a solution can be sort.
At present, one airport plugs into the modem via ethernet, and wirelessly talks to the other in a couple of rooms away.
As I don't have the "dual band" version of the express station, is there anyway to maybe use the "3rd un-used" airport express to communicate with the others, but using a 2.4ghz signal so that the iphones can maybe jump onto that one?

macboi_NZ, Welcome to the discussion area!
You will either need to operate in the 2.4 GHz band OR get an inexpensive wired router to connect to the modem. Then connect 2 of the AirPort Express (AX) to Ethernet LAN ports on the router. Use one of the AXs to create a 2.4 GHz network and the other to create a 5 GHz network. Configure both the AXs to act as bridges (NOT sharing a single IP address).

Similar Messages

  • How can get mig33(social network) in my iphone??

    how  can get mig33 (social network) in my iphone??

    Have a look at this post, I think it will answer your question https://discussions.apple.com/thread/2738373?start=0&tstart=0

  • How to get an accept to show with Invitations on the calendar.

    When I put in an appt. in the calendar and invite someone to join they get the invite but then can't accept or if they do nothing shows up on my calendar to indicate that a) I invited someone and b) they accepted.  Has anyone found a way for the invites to work?

    I saw someone  wrote To go into http://me.com and go into. Calendars and delete the event in there and that would take it off the iPhone and iPad and that worked!

  • How to get real value from selectOneChoice with javascript?

    Hi,
    How to get real value from selectOneChoice with javascript? The event.getNewValue() only gets me the index of the selected item, not the value/title.
    JSF page:
    <af:resource type="javascript">
    function parseAddress(event)
    alert("new value: " + event.getNewValue());
    </af:resource>
    <af:selectOneChoice label="Location:" value="" id="soc4">
    <af:clientListener type="valueChange" method="parseAddress" />
    <f:selectItems value="#{Person.locations}" id="si7"/>
    </af:selectOneChoice>
    HTML :
    <option title="225 Broadway, New York, NY-10007" selected="" value="0">225 Broadway (Central Office)</option>
    <option title="90 Mark St., New York, NY-10007" value="1">90 Mark St. (Central Office)</option>
    Thanks a lot.

    Something I was missing ,
    You need to add valuePassThru="true" in your <af:selectOneChoice component. I have personally tested it and got the actual value in alert box. I hope this time you got the real solution. You can also test the following code by your end.
    <?xml version='1.0' encoding='UTF-8'?>
    <jsp:root xmlns:jsp="http://java.sun.com/JSP/Page" version="2.1"
    xmlns:f="http://java.sun.com/jsf/core"
    xmlns:h="http://java.sun.com/jsf/html"
    xmlns:af="http://xmlns.oracle.com/adf/faces/rich">
    <jsp:directive.page contentType="text/html;charset=UTF-8"/>
    <f:view>
    <af:document id="d1">
    <af:form id="f1">
    <af:panelBox text="PanelBox1" id="pb1">
    <af:selectOneChoice label="Set Log Level" id="soc1"
    value="#{SelectManagedBean.loggerDefault}"
    valuePassThru="true">
    <af:selectItem label="select one" value="First" id="s6"/>
    <af:selectItem label="select two" value="Second" id="s56"/>
    <af:clientListener method="setLogLevel" type="valueChange"/>
    </af:selectOneChoice>
    <af:resource type="javascript">
    function setLogLevel(evt) {
    var selectOneChoice = evt.getSource();
    var logLevel = selectOneChoice.getSubmittedValue();
    // var logLevelObject = AdfLogger.NONE;
    alert("new value is : " + logLevel);
    //alert(evt.getSelection);
    //alert(logLevelObject);
    evt.cancel();
    </af:resource>
    </af:panelBox>
    </af:form>
    </af:document>
    </f:view>
    </jsp:root>

  • I have a I-mac that is not able to upgrade the os past 10.7.5, when I go to upgrade Pages it says i have to be running os 10.10, how can I get Pages that will run with os 10.7.5.

    I have a I-mac that is not able to upgrade the os past 10.7.5, when I go to upgrade Pages it says i have to be running os 10.10, how can I get Pages that will run with os 10.7.5.

    Click here and follow the instructions. If they’re not applicable, buy an iWork 09 DVD from a source such as Amazon or eBay.
    (116937)

  • Update to kichat: FAQ 2 - How to get my router to work with iChat?

    kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
    (Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
    Getting your router started with iChat.
    Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
    Glossary for this FAQ
    Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
    Routers seem to fall into two categories
    Those that work straight from the box. See Apple Article HT1787
    NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
    Even then some list that they need tweaks.
    and those that do not.
    This post will deal with what you may need to look at.
    First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
    Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
    In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
    Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
    Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
    The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
    Opening or Allowing ports. Several Methods not all devices have all of them.
    DMZ (Demilitarised Zone)
    This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
    Port Forwarding (also Virtual Server or Pin Holes)
    These settings are usually found in an Advanced setting.
    You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
    See this pic for an example of the description above.
    In this example shows that on some Port AND Protocols need to be listed.
    iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
    See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
    My Note 2:
    On the first link Note 1 under tables in that link would be better if it read:
    " 1. All iChat AV traffic is UDP -
    except for ports 5190 and 5298, which need to be open for both TCP as well;
    and 5220, 5222, which need to be open for TCP only. "
    Note 2
    GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
    UPnP Universal Plug n Play.
    This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
    By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
    They close after the application has finished with them on a timed basis.
    On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
    Trigger Ports
    Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
    The first port for incoming Video or Audio invites is port 5678.
    Pre iChat 4
    When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
    See this variation where only the ports listed above are completed.
    The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
    iChat 4
    The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
    At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
    Wireless
    Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
    Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
    Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
    Multiple devices
    Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
    Further Help
    I have found that this site (ADSLGuide) to be helpful.
    It is British based but I have linked you to the Apple Related Discussions Forum.
    Eliminating Problems on my Personal web pages.
    The ports and their function within iChat. (my personal Web pages again)
    This is not a step by step approach. You will have to read around the information about your device.
    Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
    Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
    Click on your device.
    Select iChat on the next page.
    Follow the info on the next.
    This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
    Gives you a chance to look at at pics to give clues to where some of these other things are.
    With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
    and to EZ Jim for his work on iSights on my web pages.
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.
    9:51 PM Saturday; December 6, 2008

    kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
    (Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
    Getting your router started with iChat.
    Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
    Glossary for this FAQ
    Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
    Routers seem to fall into two categories
    Those that work straight from the box. See Apple Article HT1787
    NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
    Even then some list that they need tweaks.
    and those that do not.
    This post will deal with what you may need to look at.
    First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
    Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
    In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
    Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
    Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
    The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
    Opening or Allowing ports. Several Methods not all devices have all of them.
    DMZ (Demilitarised Zone)
    This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
    Port Forwarding (also Virtual Server or Pin Holes)
    These settings are usually found in an Advanced setting.
    You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
    See this pic for an example of the description above.
    In this example shows that on some Port AND Protocols need to be listed.
    iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
    See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
    My Note 2:
    On the first link Note 1 under tables in that link would be better if it read:
    " 1. All iChat AV traffic is UDP -
    except for ports 5190 and 5298, which need to be open for both TCP as well;
    and 5220, 5222, which need to be open for TCP only. "
    Note 2
    GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
    UPnP Universal Plug n Play.
    This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
    By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
    They close after the application has finished with them on a timed basis.
    On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
    Trigger Ports
    Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
    The first port for incoming Video or Audio invites is port 5678.
    Pre iChat 4
    When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
    See this variation where only the ports listed above are completed.
    The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
    iChat 4
    The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
    At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
    Wireless
    Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
    Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
    Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
    Multiple devices
    Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
    Further Help
    I have found that this site (ADSLGuide) to be helpful.
    It is British based but I have linked you to the Apple Related Discussions Forum.
    Eliminating Problems on my Personal web pages.
    The ports and their function within iChat. (my personal Web pages again)
    This is not a step by step approach. You will have to read around the information about your device.
    Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
    Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
    Click on your device.
    Select iChat on the next page.
    Follow the info on the next.
    This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
    Gives you a chance to look at at pics to give clues to where some of these other things are.
    With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
    and to EZ Jim for his work on iSights on my web pages.
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.
    9:51 PM Saturday; December 6, 2008

  • I have Lookout 6.5 running with Windows 7, the process has been running for about 2 months with no problems, but today the Citadel stopped working! I am having a hard time getting it started again, need help!

    I have Lookout 6.5 running with Windows 7, the process has been running for about 2 months with no problems, but today the Citadel stopped working!
    How could this have happened and what can I do to get it running again? 

    Didnt realize there was a response, late getting back to you.
    Save your process files outside of the NI progam directory (you should have external backups already right ).  THey should not be deleted.
    Any customizations to the lookout.ini and lookout.sec file may be lost.  
    Mike
    Forshock - Consult.Develop.Solve.

  • How to get kensington K9294 to connect with original iPad. Bluetooth is on.

    How to get Kensington K9294 to connect with original iPad. Bluetooth is on.

    Sorry, but what is a Kensington K9294? I can find no mention of that product ID on the web, not even on Kensington's site. Do you mean the K39294, the KeyFolio keyboard/case?
    Regards.

  • How to get string from jtextpane along with its attributes

    sir,
    How to get string from jtextpane along with its attributes
    i,e font,size,style,color etc.
    please help me out.
    my mail id is [email protected]

    JTextPane extends JTextComponent
    JTextComponent.getDocument()
    a Document is a set of Element, see Document.getRootElements(). Each Element has attributes, stored within an AttributSet object see Element.getAttributes()
    a Document can also be rendered as a String, see Document.getText( offest, length ), use it with 0 and Document.getLength() as parameters.

  • How to get list of company codes with current period not opened?

    Hi,
    How to get list of company codes with current period not opened?
    Is there any way we can check whether the current period is opened for all company codes.
    If not how, can we generate a report which having information of period and company code. Also please tell me, which table will have info on posting periods and company codes.
    Thanks
    Vineeth Varghese

    Hi,
    The MM periods details can be viewed In Table MARV . On the selection screen you have the option of entering the company codes , current period, year current period etc. so make the required entries and you get the all details relevant to MM periods. Also it can be downloaded as a report.Thanks

  • How to get this script to work with different browser

    Do you guys know how to get this script to work with mozilla firefox? 
    do shell script "open -a safari 'https://login.binck.nl/klanten/Login.aspx?ReturnUrl=%2fklanten%2fdefault.aspx'"
    tell application "Safari"
      activate
              tell document 1
                        repeat until ((do JavaScript "location.host") is "login.binck.nl")
                                  delay 1
                        end repeat
      do JavaScript"document.getElementById('ctl00_Content_Gebruikersnaam').value='sim';document.ge tElementById('ctl00_Content_Wachtwoord').value='password';window.open(document. g etElementById('ctl00_Content_LoginButton').href, '_self', 'true');"
              end tell
    end tell
    Thank you so much in advance:)

    That isn't possible. Firefox's AppleScript dictionary doesn't contain anything which can be used to manage JavaScripts.
    (63741)

  • How to get list of active users with the details like samaccountname, name, department, job tittle, email in active directoy?

    how to get list of active users with the details like samaccountname, name, department, job tittle, email in active directoy?

    You can use third party software True Last Logon 2.9.You can export the file in excel for report creation.You can use the trial version this will achieve what you are looking for.
    True Last Logon displays the following Active Directory information:
    --Users real name and logon name
    --Detailed account status
    --Last Logon Date & Time
    --Last Logon Timestamp (Replicated value)
    --Account Expiry Date & Time
    --Enabled or Disabled Account
    --Locked Accounts
    --Password Expires
    --Password Last Set Date & Time
    --Logon Count
    --Bad Password Count
    --Expiry Date
    --You can also query for any other attribute (Example: Description, telephone Number, custom attibutes etc)
    Refer the below link for trial version:
    http://www.dovestones.com/products/True_Last_Logon.asp
    Best Regards,
    Sandesh Dubey.
    MCSE|MCSA:Messaging|MCTS|MCITP:Enterprise Adminitrator |
    My Blog
    Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

  • HT201269 how to transfer music from pc running with windows7 to iphone

    how to transfer music from pc running with windows7 to iphone4

    Just connect your iPhone to pc and open the iTunes then go to the option showing [add file to library or add folder to library in file option] on your left side of the desktop screen and click on apply and then sync.
    That's how I transfer music from computer to iPhone.

  • How to get online apps to work with the Verizon DSL modem firewall set at "Medium" level, not "Low?"

    How to get online apps to work with the Verizon DSL modem firewall set at “Medium” level? Xbox 360 Live, FTP, and the Windows sntp Time checker native to Windows XP WON’T WORK unless the Verizon firewall is first reset down to “Low.” Then all works well, but I then risk low firewall protection. Setup: · Westell 6100 DSL modem (Software Version: VER:4.04.03.00 Transceiver Revision: 7.2.3.0 Model Name: C90-610015-06), · D-Link DIR-655 wireless router (Hardware Version: A3, Firmware Version: 1.21), For Xbox 360 Live the “canned” port forwarding rule for provided in Verizon’s drop-down list for the Westell 6100 modem forwards ports 88 and 3074 for both TCP and UDP. This does not meet Microsoft’s forwarding recommendations for Xbox 360 Live stated at http://support.microsoft.com/kb/908874. Instead, for the Verizon modem (Westell) I made a new port forwarding rule to comply with those Microsoft instructions. It forwards ports 53, 80 and 3074 for TCP and ports 53, 88 and 3074 for UDP. These same ports are also forwarded in the D-Link router configuration. For FTP, port 21 is also forwarded for TCP and UDP in both modem and router. But they don’t work until I first cripple the Verizon firewall down to “Low.” How to get them to work with the Verizon firewall up to Medium?

    While I do not know the answer to your question, BUT since you have this modem and another router - you could just follow.
    http://www.dslreports.com/faq/13600
    ^^
    If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

  • How to get whatsapp on BBCurve 9300 with normal internet GPRS plan??

    How to get whatsapp on BBCurve 9300 with normal internet GPRS plan??

    Download the iTunesSetup package on the laptop, and then move it to the Dell. You may need to hook up the iPod to an Internet-enabled computer initially so that it has the correct firmware without storing the iTunes library on that computer.
    (30551)

Maybe you are looking for