How to get best routing performance for 320n?

Ok, I verified that the PC link is Gigabit and the WAN link is Gigabit.
I should be able to pull speedtests down in the 100mbps range, which I can do if I bypass the 320n.
However, with the 320n in place, I get about 60mbps speedtests, or 70mbps (when overclocked to 400 MHz from 354 MHz).
Anyway to get closer to 100mbps without overclocking any further?  Smallnetbuilder rated the 320n about 144 mbps throughput, but I take it that's in both directions at the same time? 144/2 = 72mbps, and after overhead that seems about right for speedtests in the 60-70 mbps range.
I take it I should return this router and get another brand.

Thanks, I will check that out.  I was looking up info on Tomato, but it seemed it was for the old WRT-54g / gs, etc...
I ran it at the stock clock (I think stock is 354 MHz) for awhile.  I over clocked it only by 46 MHz maybe two weeks ago.  They still freeze up at stock clock with default wireless power.  The thing is, the broadcom CPU in this thing is the same part number used in other routers, and it's clocked at 400 MHz in some models, and 533 MHz in others.  It's terribly underclocked in this router.  I don't know if it's because they didn't want to spend money on better heatsinks or higher quality power supply circuitry and capacitors, or what.
That's another thing that could be bad. Inferior components, such as slightly out of tolerance capacitors, or cheap lead-free solder that wasn't melted to the right temperature in the board flow production process.  Under heavy load it can crack and cause bad connections or cause heatsinks to come off the board (if any).  It was a major problem with the Xbox 360, and it's a major problem in the HP 2015dn laser printer.
Who knows what the deal is.  My 320n seems stable now.  I was just hoping to get a little more routing speed out of it.  I'll read up on Tomato and see if that's a feasible solution.

Similar Messages

  • How to get best OC performance from Athlon 64 system

    Another OC article, that covers differant ways of OC a Athlon 64 system and what gives best perormance boost.
    http://www.neoseeker.com/Articles/Hardware/Guides/athlon64oc/index.html
    PS Sorry did not see that Worf105 already posted same thing... 

    Thanks, I will check that out.  I was looking up info on Tomato, but it seemed it was for the old WRT-54g / gs, etc...
    I ran it at the stock clock (I think stock is 354 MHz) for awhile.  I over clocked it only by 46 MHz maybe two weeks ago.  They still freeze up at stock clock with default wireless power.  The thing is, the broadcom CPU in this thing is the same part number used in other routers, and it's clocked at 400 MHz in some models, and 533 MHz in others.  It's terribly underclocked in this router.  I don't know if it's because they didn't want to spend money on better heatsinks or higher quality power supply circuitry and capacitors, or what.
    That's another thing that could be bad. Inferior components, such as slightly out of tolerance capacitors, or cheap lead-free solder that wasn't melted to the right temperature in the board flow production process.  Under heavy load it can crack and cause bad connections or cause heatsinks to come off the board (if any).  It was a major problem with the Xbox 360, and it's a major problem in the HP 2015dn laser printer.
    Who knows what the deal is.  My 320n seems stable now.  I was just hoping to get a little more routing speed out of it.  I'll read up on Tomato and see if that's a feasible solution.

  • How to get best speeds possible for Linksys E1200 ?

    I have 3 Wireless Devices connected to my Router which is a Ipad, Ipod Touch & laptop.
    I have 2 hard Wired conneted to my Router which is a ps3 and a Desktop. 
    How can i have great speeds and reliable connection on all of them. 
    Sometimes my ps3 lags.. 
    When i do Speed test on ipod & ps3.. The download speed changes a bit.

    Try changing your wireless router's channel through your router's configuration page to see if your signal strength improves. You don't need to change your computer's configuration, because it can automatically detect the new channel.
    To find your router configuration page, consult this quick reference table, which shows the default addresses for common router manufacturers. If the address is not listed here, read the documentation that came with your router, or visit the manufacturer's webpage.
    RouterAddress
    3Com
    http://192.168.1.1
    D-Link
    http://192.168.0.1
    Linksys
    http://192.168.1.1
    Microsoft Broadband
    http://192.168.2.1
    Netgear
    http://192.168.0.1
    Actiontec
    http://192.168.0.1
    Thanks,
    Rich
    Ask your any query related with your Linksys router, I am always available on this Cisco Community for help
    Mod Note: Link to 3rd party support removed.

  • Update to kichat: FAQ 2 - How to get my router to work with iChat?

    kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
    (Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
    Getting your router started with iChat.
    Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
    Glossary for this FAQ
    Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
    Routers seem to fall into two categories
    Those that work straight from the box. See Apple Article HT1787
    NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
    Even then some list that they need tweaks.
    and those that do not.
    This post will deal with what you may need to look at.
    First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
    Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
    In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
    Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
    Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
    The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
    Opening or Allowing ports. Several Methods not all devices have all of them.
    DMZ (Demilitarised Zone)
    This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
    Port Forwarding (also Virtual Server or Pin Holes)
    These settings are usually found in an Advanced setting.
    You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
    See this pic for an example of the description above.
    In this example shows that on some Port AND Protocols need to be listed.
    iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
    See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
    My Note 2:
    On the first link Note 1 under tables in that link would be better if it read:
    " 1. All iChat AV traffic is UDP -
    except for ports 5190 and 5298, which need to be open for both TCP as well;
    and 5220, 5222, which need to be open for TCP only. "
    Note 2
    GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
    UPnP Universal Plug n Play.
    This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
    By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
    They close after the application has finished with them on a timed basis.
    On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
    Trigger Ports
    Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
    The first port for incoming Video or Audio invites is port 5678.
    Pre iChat 4
    When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
    See this variation where only the ports listed above are completed.
    The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
    iChat 4
    The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
    At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
    Wireless
    Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
    Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
    Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
    Multiple devices
    Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
    Further Help
    I have found that this site (ADSLGuide) to be helpful.
    It is British based but I have linked you to the Apple Related Discussions Forum.
    Eliminating Problems on my Personal web pages.
    The ports and their function within iChat. (my personal Web pages again)
    This is not a step by step approach. You will have to read around the information about your device.
    Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
    Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
    Click on your device.
    Select iChat on the next page.
    Follow the info on the next.
    This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
    Gives you a chance to look at at pics to give clues to where some of these other things are.
    With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
    and to EZ Jim for his work on iSights on my web pages.
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.
    9:51 PM Saturday; December 6, 2008

    kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
    (Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
    Getting your router started with iChat.
    Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
    Glossary for this FAQ
    Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
    Routers seem to fall into two categories
    Those that work straight from the box. See Apple Article HT1787
    NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
    Even then some list that they need tweaks.
    and those that do not.
    This post will deal with what you may need to look at.
    First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
    Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
    In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
    Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
    Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
    The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
    Opening or Allowing ports. Several Methods not all devices have all of them.
    DMZ (Demilitarised Zone)
    This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
    Port Forwarding (also Virtual Server or Pin Holes)
    These settings are usually found in an Advanced setting.
    You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
    See this pic for an example of the description above.
    In this example shows that on some Port AND Protocols need to be listed.
    iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
    See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
    My Note 2:
    On the first link Note 1 under tables in that link would be better if it read:
    " 1. All iChat AV traffic is UDP -
    except for ports 5190 and 5298, which need to be open for both TCP as well;
    and 5220, 5222, which need to be open for TCP only. "
    Note 2
    GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
    UPnP Universal Plug n Play.
    This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
    By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
    They close after the application has finished with them on a timed basis.
    On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
    Trigger Ports
    Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
    The first port for incoming Video or Audio invites is port 5678.
    Pre iChat 4
    When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
    See this variation where only the ports listed above are completed.
    The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
    iChat 4
    The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
    At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
    Wireless
    Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
    Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
    Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
    Multiple devices
    Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
    Further Help
    I have found that this site (ADSLGuide) to be helpful.
    It is British based but I have linked you to the Apple Related Discussions Forum.
    Eliminating Problems on my Personal web pages.
    The ports and their function within iChat. (my personal Web pages again)
    This is not a step by step approach. You will have to read around the information about your device.
    Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
    Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
    Click on your device.
    Select iChat on the next page.
    Follow the info on the next.
    This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
    Gives you a chance to look at at pics to give clues to where some of these other things are.
    With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
    and to EZ Jim for his work on iSights on my web pages.
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.
    9:51 PM Saturday; December 6, 2008

  • How to get 64 bit version for premiere elements 12

    How to get  64-bit version for Premier Elements 12 ? 
    I download from ADMISY site.
    Click on win 64 bit and download it.
    When I try to install ther is a error  this download version is not for 64 bit I have try many times but same result

    Hello
    I have been away some days
    ADMISY is a software partners for Adobe
    I running Win 7 Home Edition
    I have received a card with a code when I bought the program and the I
    download from ADMISY
    Sending serial and installation warning
    PhotoshopElements_12_WWEFDJ.7z
    PhotoshopElements_12_WWEFDJ
    PremiereElements_12_WWEFDJ_win32.7z
    PremiereElements_12_WWEFDJ_win32
    I can not find a 64 bit version of 32-bit or 64-bit version of downloads
    This is information I have
    Best regards
    Erling Magnusson
    2015-02-04 22:33 GMT+01:00 Adobe Forums <[email protected]>:
        How to get 64 bit version for premiere elements 12  created by A.T.
    Romano <https://forums.adobe.com/people/A.T.+Romano> in *Premiere
    Elements* - View the full discussion
    <https://forums.adobe.com/message/7162950#7162950>

  • How to get count of rows for a table?

    Hi,
    How to get count of rows for a table and secondly, how can i have access to a particular cell in a table?
    Regards,
    Devashish

    Hi Devashish,
    WdContext.node<Your_node_name>().size() will give you the no: of rows.
    This should be the node that is bound to the table's datasource property.
    WdContext.node<Your_node_name>().get<node_name>ElementAt(index_value); will select the row at that particular index.
    You can access an attribute of a particular row as
    WdContext.node<Your_node_name>().get<node_name>ElementAt(index_value).get<attribute_name>();
    Hope this helps,
    Best Regards,
    Nibu.
    Message was edited by: Nibu Wilson

  • How to get the health , performance information and about the services run on devices that have connected to the system center?

    Hi All,
    I want to know how to get the health , performance information and about the services run on devices that have connected to the system center to my c# application. Also I need to know about the information of databases that have connected to system center.
    I will appreciate your feedback
    Thank you

    Hi,
    You can configure service monitor for the required service on the server
    refer below link for how to configure service monitoring
    http://www.bictt.com/blogs/bictt.php/2011/03/17/scom-monitoring-a-service-part3
    You can use SCOM SDK to connect to the scom server using c# and get required information
    http://msdn.microsoft.com/en-us/library/hh329086.aspx
    you can find the database in below registry path on management server
    HKLM:\SOFTWARE\Microsoft\Microsoft Operations Manager\3.0\Setup\DatabaseName
    Regards
    sridhar v

  • Magic Packet - How to get my router to send one

    I have the Quantum Gateway 1100 router.  I have a NAS Server on my home network.  The NAS server has the capability to Wake on LAN if the router can send that packet.  Can anyone tell me how to get the router to send the Wake-on-Lan packet to the server.  FIOS Tech Support is completely and totally useless.

    Hi,
    You can do a fresh installation using the installer bits available at the following link/location Download CS5.5 products
    For suites, you need to download and copy both .7z and .exe in the same folder. Clicking .exe will extract all relevant installer files. You can then install the suite. Use your existing Serial number when prompted.
    regards
    Aj

  • How to get Best practices solution

    Hi,
           We want to apply Best practices in our server.
           Please inform how to get best practices by solution manager or SAP servive merket place.
    Best regards,
       Gaito

    Use your Secure user id to login to hxxp://service.sap.com . Click on "Quick Links" on top right corner of market place. Under "Software downloads", navigate to "Installations and Upgrades" link.
    You can search for "Best Practices" from here.

  • How to get the last error for while loop?

    How to get the last error for while loop? I just want transfer the last error for while loop, but the program use the shift register shift all error every cycle.

    What do you mean by "get" and "transfer"?
    If the shift register is not what you want, use a plan tunnel instead.
    Typically, programmers are interested in the first, not last, error.
    Can you show us your code so we have a better idea what you are trying to?
    LabVIEW Champion . Do more with less code and in less time .

  • HOW TO USE A SINGLE PERFORM FOR VARIOUS TABLES ?

    perform test TABLES t_header.
    select
           KONH~KNUMH
           konh~datab
           konh~datbi
           konp~kbetr
           konp~konwa
           konp~kpein
           konp~kmein
           KONP~KRECH
           FROM konh INNER JOIN konp
                  ON konpknumh = konhknumh
           into table iTABXXX
            "ANY TEMPERARY INTERNAL TABLE.
           for all entries in t_header
           where
                 konh~kschl = t_header-kschl
             AND konh~knumh = t_header-knumh.
    endform.
    how can I use above perform for various internal tables of DIFFERENT LINE TYPES but having the fields KSCHL & KNUMH.

    u can use single perform....
    just see this example......hope this is what u r expecting....
    tables : pa0001.
    parameters : p_pernr like pa0001-pernr.
    data : itab1 like pa0001 occurs 0 with header line.
    data : itab2 like pa0002 occurs 0 with header line.
    perform get_data tables itab1 itab2.
    if not itab1[] is initial.
    loop at itab1.
    write :/ itab1-pernr.
    endloop.
    endif.
    if not itab2[] is initial.
    loop at itab2.
    write :/ itab2-pernr.
    endloop.
    endif.
    *&      Form  get_data
          text
         -->P_ITAB1  text
         -->P_ITAB2  text
    form get_data  tables   itab1 structure pa0001
                            itab2 structure pa0002.
    select * from pa0001 into table itab1 where pernr = p_pernr and begda le sy-datum and endda ge sy-datum.
    select * from pa0002 into table itab2 where pernr = p_pernr and begda le sy-datum and endda ge sy-datum.
    endform.                    " get_data
    Regards
    vasu

  • How to get title templates library for CC?

    How to get title templates library for CC?  Do you have to download and install PP 6 to get them?

    Try here Library, title templates, template projects missing: Premiere Pro, After Effects, Encore

  • How to get balance sheet report for profit centers

    hi
    how to get balance sheet report for profit centers, is there any transcation code to get that report or i need to create a report painter report for this

    Hi,
    You can use T. code KE5Z for actual line items.
    More to this you can use program RFBILA10 (Use T. code SE38 and program RFBILA10) for complete blance sheet.
    The transaction is for special purpose ledger but this program RFBILA10 can be used for profit center balance also.
    In selection, you can give ledger name which is generally 8A for profit center ledger.
    Reg

  • I went to add my iPod to another computer and when I did it re-bought all of my music and I would like to know how to get my money back for it?

    I went to add my iPod to another computer and when I did it re-bought all of my music and I would like to know how to get my money back for it?
    anyonr know how I can get my money back????????

    Go to Settings>General>Reset>Erase all content and setting. Then re-setup the iPod with your account/media. To redownload iTunes purchases see:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • How to get the depreciation areas for an asset in particular period

    Hi frndz,
      how to get the depreciation areas for an asset in a particular period for writeup or manual depreciation method.
    Thanks and regards.
    Harisumanth.Ch

    Try table ANLB, then read ANLC.
    Regards.

Maybe you are looking for