How to get landscape mode to work?

My landscape mode won't work. It was working fine before, and all of a sudden I can't get it to work now. My phone is only a week old!

Reset it, hold down the home and sleep buttons, ignore the red Off slider, wait for the Apple logo and let go of the buttons. Before you do this, is the lock screen icon showing on the top right of the iPhone?

Similar Messages

HP Phoenix 8-core - how do I get XP Mode to work in Windows 7 64-bit?

My Computer: HP Phoenix 8-core, 12 GB Ram, over 1,000GB hard drive space, Win 7 SP1 with current updates. Downloaded and installed the following: Windows XP Mode with Windows Virtual PC, the hotfix MS provided for AMD multicore, and the MS Hardware-Assisted Virtualization Detection Tool which informed me that my computer does have hardware-assisted virtualization. I have done EVERYTHING Microsoft has advised.
How do I get XP Mode to work?

Frank, thanks for the help. That Microsoft article is the one I read yesterday morning. I again just now went into the BIOS as follows: Security, System Security-Data Execution Prevention AND Virtualization Technology were both enabled. So I saved changes and exited. My computer is running Windows 7 Professional 64-bit.
This is my system information:
OS Name   Microsoft Windows 7 Professional
Version   6.1.7601 Service Pack 1 Build 7601
Other OS Description    Not Available
OS Manufacturer   Microsoft Corporation
System Name   HPPHOENIX
System Manufacturer   Hewlett-Packard
System Model   h9-1100z
System Type   x64-based PC
Processor   AMD FX(tm)-8150 Eight-Core Processor, 3600 Mhz, 4 Core(s), 8 Logical Processor(s)
BIOS Version/Date   AMI Ang_716, 4/5/2012
SMBIOS Version   2.7
Windows Directory   C:\Windows
System Directory   C:\Windows\system32
Boot Device   \Device\HarddiskVolume1
Locale   United States
Hardware Abstraction Layer   Version = "6.1.7601.17514"
User Name   HPPHOENIX\Debbie
Time Zone   Eastern Daylight Time
Installed Physical Memory (RAM)   12.0 GB
Total Physical Memory   11.8 GB
Available Physical Memory   10.2 GB
Total Virtual Memory   23.6 GB
Available Virtual Memory   21.7 GB
Page File Space   11.8 GB
Page File   C:\pagefile.sys
I downloaded and installed the Windows XP Mode. The
I downloaded and installed the Windows Virtual PC. (not the 2007 version-tried that the first time and seen it did not work).
I applied the "fix" for AMD motherboards.
I just tried to install XP Mode again--I got almost to the end, the I got the following error message in a rectangle box:
"Windows XP Mode-Windows Virtual PC
Could not complete Setup. Please try again."
The has happened over 7 times. Yesterday evening before I posted on this forum, I uninstalled, deleted everything, restarting the computer after doing each step, went to website yet again, redownloaded everything again, and tried to install once again. Still the same message. Any help or advice is certainly needed and appreciated. Debbie

Cant get Security Mode to work on WRT54G

I have everything set up fine.. internet working etc but I cannot get security mode to work.. I go to click on WEP, WPA.. whatever and it just autos back to DISABLED.. Anyone to fix this?

how many computers do you have?
try to use other computers in setting up the security. check also the firmware of your router.make sure you have the latest one.

Update to kichat: FAQ 2 - How to get my router to work with iChat?

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

I have an airbook, 10.7.4 LION, thunderbolt ethernet adapter and when trying to install 1.2.1 thunderbolt upgrade it says "this software not supported on this system"? Any advice on how to get the adapter to work?

I have a new airbook, 10.7.4 LION, thunderbolt ethernet adapter and when trying to install 1.2.1 thunderbolt upgrade it says "this software not supported on this system"? Any advice on how to get the adapter to work?

Welcome to Apple Support Communities
If you purchased the computer before 2010, your computer hasn't got Thunderbolt, so you can't use it

How to get the webcam to work?

Hi,
As I don't have an instruction book for this computer, can anyone tell me how to get the webcam to work please?
There is supposed to be something that pops up from the side of the screen, but I've left the mouse sit there for ages on all sides and nothing. Please assist me.
Kit_e

I refer you back to my original question.
There used to be a bar at the side that popped up when you left the mouse sit there for a bit. It no longer pops up ... ie: it's disappeared and will not return ... this is what "started" the webcam for use as a webcam.
I have no idea on how to use the webcam from any other place. There is no icon. There is no mention of it in the programs list. There is nothing. There is a webcam sitting there in the laptops lid, but I can't find where to "access it". Like I said there is no icon, nothing in the programs list.
I want to be able to use it. You know, like you use a webcam. On the web, as a camera. No particular website or software that I have in mind.
Thanks.

How to get this script to work with different browser

Do you guys know how to get this script to work with mozilla firefox?
do shell script "open -a safari 'https://login.binck.nl/klanten/Login.aspx?ReturnUrl=%2fklanten%2fdefault.aspx'"
tell application "Safari"
activate
          tell document 1
                    repeat until ((do JavaScript "location.host") is "login.binck.nl")
                              delay 1
                    end repeat
do JavaScript"document.getElementById('ctl00_Content_Gebruikersnaam').value='sim';document.ge tElementById('ctl00_Content_Wachtwoord').value='password';window.open(document. g etElementById('ctl00_Content_LoginButton').href, '_self', 'true');"
          end tell
end tell
Thank you so much in advance:)

That isn't possible. Firefox's AppleScript dictionary doesn't contain anything which can be used to manage JavaScripts.
(63741)

Hi. I have Snap To Grid and By Kind enabled in Lion but it's not working. When I trash an icon, instead of snapping the remaining icons to the By Kind grid, a space is left where the trashed icon was. Any suggestions on how to get Snap To Grid working?

Hi. I have Snap To Grid and By Kind enabled in Lion but it's not working. When I trash an icon, instead of snapping the remaining icons to the By Kind grid, a space is left where the trashed icon was. Any suggestions on how to get Snap To Grid working?

Where are you talking about the Desktop?
I don't see where it is possible to set both Snap to Grid and By Kind they seem to be mutually exclusive.
And then
If I have Snap to grid set I get the behavior you describe. If I have By Kind set the icons stay together and close up the space from the deleted icon.
regards

Any suggestions for how to get my logic keyboard working properly for FCE?

Any suggestions how to get my logic keyboard working properly for FCE? I can't use some of the shortcuts - insert, overwrite etc. maybe the system settings aren't correct?

This normally happens when debris builds between the trackball and the rollers on the inside of the mouse.
Turn the mouse upside down and rub the trackball vigorously on a sheet of paper or microfiber cloth to try and free it up.
Regards,
Captfred

How to get my Addon to work with the license key?

Hi,
Can someone tell me how to get the Addon to work with the license key?
I've follow the steps as stated in this thread:
[Re: SBO 2005 A - How do I get a Connection string from SAP B1.|Re: SBO 2005 A - How do I get a Connection string from SAP B1.]
1) i've registered a BASIS key and get a 'BASISXXXXXX" string
2) then i paste my BASIS key in "Solution" of Add-On Indentifier Generator and generate the Add-On Indentifier Code
3) then i paste the string to my source code
which is the "XXX" of the sample code in that thread.
static string AddonIdentifierString="XXX";
int lRetCode=0;
int errCode=0;
string errMsg= string.Empty;
string connectionStr ="";
link = new SAPbouiCOM.SboGuiApiClass();
connectionStr =Environment.GetCommandLineArgs().GetValue(1).ToString();
link.AddonIdentifier=AddonIdentifierString;
link.Connect(connectionStr);
oApp = link.GetApplication(-1);
vCompany = new SAPbobsCOM.CompanyClass();
string cookie = vCompany.GetContextCookie();
string conStr = oApp.Company.GetConnectionContext(cookie);
vCompany.SetSboLoginContext(conStr);
lRetCode = vCompany.Connect();
4) then i add my add-on using manager role at Add-on admin
5) then i can see my add-on there. it not suppose to be there since i've not installed any of my add-on license for my own add-on.
what steps did i miss? Can someone please advise? Thanks
ps : i'm coding in VB

Hi,
i think you have to change the license file attributing the number of licensing for your addon, then download it from https://websmp202.sap-ag.de/smb and then install it on SAP License manager, then I think you should give the license for your addon for individual users (example manager)
I hope it helps.
Best regards

How to get online apps to work with the Verizon DSL modem firewall set at "Medium" level, not "Low?"

How to get online apps to work with the Verizon DSL modem firewall set at “Medium” level? Xbox 360 Live, FTP, and the Windows sntp Time checker native to Windows XP WON’T WORK unless the Verizon firewall is first reset down to “Low.” Then all works well, but I then risk low firewall protection. Setup: · Westell 6100 DSL modem (Software Version: VER:4.04.03.00 Transceiver Revision: 7.2.3.0 Model Name: C90-610015-06), · D-Link DIR-655 wireless router (Hardware Version: A3, Firmware Version: 1.21), For Xbox 360 Live the “canned” port forwarding rule for provided in Verizon’s drop-down list for the Westell 6100 modem forwards ports 88 and 3074 for both TCP and UDP. This does not meet Microsoft’s forwarding recommendations for Xbox 360 Live stated at http://support.microsoft.com/kb/908874. Instead, for the Verizon modem (Westell) I made a new port forwarding rule to comply with those Microsoft instructions. It forwards ports 53, 80 and 3074 for TCP and ports 53, 88 and 3074 for UDP. These same ports are also forwarded in the D-Link router configuration. For FTP, port 21 is also forwarded for TCP and UDP in both modem and router. But they don’t work until I first cripple the Verizon firewall down to “Low.” How to get them to work with the Verizon firewall up to Medium?

While I do not know the answer to your question, BUT since you have this modem and another router - you could just follow.
http://www.dslreports.com/faq/13600
^^
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Anyone have a syggestion on how to get my Ipod touch working again besides putting it into restore mode

Anyone have any ideas on how to get an Ipod touch to charge or sync without putting it into restore mode, I've prettymuch tried everything thats been put online so far

Tried DFU mode?
To do this follow these instructions:
    1. First, Open up iTunes, plug in your iPod Touch/iPhone to the Computer's USB port. Turn on your Computer's speaker and make sure it is loud enough that you can hear it.
    2. Hold down the Home button (top left for iPod Touch and top right for the iPhone with the screen facing you) and the Power button (located on the front bottom of your iPod Touch/iPhone) simutaneously, until the screen goes black and the device turns off. (past the red slider/slide to power off screen)
    3. Now let go of the Power button, but continue to hold the Home button. Your iPod Touch/iPhone should have turned off and the screen should not be on.
    4. After around ~10-20 seconds, you will hear a noise (beep/ding) from your Computer as if it had just recognized a new hardware device, now iTunes should recognize it in DFU mode.
    5. After iTunes recognizes the iPod Touch/iPhone, let go of the Home button otherwise it will go into recovery mode and you will have to do the entire DFU process over again.
    6. You will know when you have put your iPod Touch/iPhone correctly into DFU mode when the display is blank and that you do not have anything on your device.
Once you have done this click restore and iTunes sould start to dowbnload and install the latest firmware.
#Please note this will reset your iDevice to factory settings
Syther101

How to get PROCESS MODE in CRM 2007 WebClient

Hi all,
Currently, we're implementing CRM2007 WebClient -- Service Transaction.
In the past(CRM4.0 Version), we used the function 'CRM_INTLAY_GET_PROCESS_MODE' in the BADI of SAVE Service Order to identify it's a new create order or changed order.
CALL FUNCTION 'CRM_INTLAY_GET_PROCESS_MODE'
    IMPORTING
      ev_process_mode = l_dialog_mode. " A created, B changed
Now, this function does not work in Web Client. So, I turned to another function 'CRM_ORDERADM_H_READ_OW' try to get the flag of process mode.
CALL FUNCTION 'CRM_ORDERADM_H_READ_OW'
EXPORTING
    iv_orderadm_h_guid               = lv_guid_ref
IMPORTING
   ES_ORDERADM_H_WRK                = l_CRMT_ORDERADM_H_WRK
   EV_MODE                          = l_dialog_mode
Yes, function 'CRM_ORDERADM_H_READ_OW' works in WebClient. But when creating new service order, the l_dialog_mode = 'B' which is same to changing an exsiting order.
So would anyone kindly help me, How to get the process mode properly in WebClient, especially in Service Order. I need to identify the order is new created or is changed.
Your comments is really appreciated.
Best Regards,
Tony

Use function module CRM_ORDERADM_H_ON_DATABASE_OW to check, if the order has already been save on the database. If not, you are in create mode.

Can't get landscape mode with Qmix app on my iPod touch 4th generation....

I cannot get my iPod touch to go into landscape mode either with the calculator or with my Persons Qmix software app. I have no problems on the iPhone or iPad, but it has all of a sudden stopped working. I tried rebooting the OS, a reset and the orientation lock is off on the unit...help?

Well, it went into landscape mode and I used it with QMix several times, then all of a sudden it would not go into landscape mode for ANYTHING not just QMix and Ihave tried double tapping on the bottom and making sure the orientation lock was not on......any other ideas? Im thinking i may have to send it to Apple to get this resolved...

Can't get 'clamshell' mode to work with Dell 2408

I have been trying to get my Dell 2408 working in clamshell mode without any success. I have a USB keyboard, USB mouse, power adapter and monitor via DVI plugged in. I switch the display type to mirror, close the lid, wait for it to sleep, then wake it again by pressing a key on the keyboard.
The computer wakes, the external monitor flashes but at the incorrect resolution (1200 X 800 instead of 1920 X 1200) then goes back to sleep. This will repeat over and over again until I open the lid of the macbook. I can occasionally get the macbook to wake and display on the eternal monitor but this is very rare, and when it does I get some wired artifacts.
What's really puzzling is that the monitor works flawlessly in extended desktop mode, and works perfectly with other non mac computers. I took the macbook to the Genius Bar, hooked it up to the apple cinema displays and i didn't get the same problem! Grrr....
So I just don't get it, both the computer and display seemingly work fine independently from one another, work fine in extended mode, yet in clamshell mode have some fairly major issues.
Anyone have any ideas?

My dell 2408 arrived today and I'm having exactly the same problem.I cant get it to go into clamshell mode. I lie, I got it to go into clamshell mode once. I don't know what I did. But it certainly isn't willing to go into clamshell mode again any time soon.

How to get landscape mode to work?

Similar Messages

Maybe you are looking for