How to get macbook pro to work with a canon wft-e6 wireless file transmitter
I recently purchased a Canon WFT-E6 wireless file transmitter for my 1DX Canon Camera. I can't find a way to set up my Notebook Pro to work with this device. Has anyone run into the same issue? and if so do you have a solution?
My guess is that you will see a wireless network in range using your Airport menu. The Airport menu looks like
. If it is all gray and nothing is inside of it, then the network was not properly setup. I do not have one, but if you tried to setup the network, and you can't see the device, then you might need Canon's support.
Similar Messages
-
Update to kichat: FAQ 2 - How to get my router to work with iChat?
kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008 -
How to get this script to work with different browser
Do you guys know how to get this script to work with mozilla firefox?
do shell script "open -a safari 'https://login.binck.nl/klanten/Login.aspx?ReturnUrl=%2fklanten%2fdefault.aspx'"
tell application "Safari"
activate
tell document 1
repeat until ((do JavaScript "location.host") is "login.binck.nl")
delay 1
end repeat
do JavaScript"document.getElementById('ctl00_Content_Gebruikersnaam').value='sim';document.ge tElementById('ctl00_Content_Wachtwoord').value='password';window.open(document. g etElementById('ctl00_Content_LoginButton').href, '_self', 'true');"
end tell
end tell
Thank you so much in advance:)That isn't possible. Firefox's AppleScript dictionary doesn't contain anything which can be used to manage JavaScripts.
(63741) -
How to get my Addon to work with the license key?
Hi,
Can someone tell me how to get the Addon to work with the license key?
I've follow the steps as stated in this thread:
[Re: SBO 2005 A - How do I get a Connection string from SAP B1.|Re: SBO 2005 A - How do I get a Connection string from SAP B1.]
1) i've registered a BASIS key and get a 'BASISXXXXXX" string
2) then i paste my BASIS key in "Solution" of Add-On Indentifier Generator and generate the Add-On Indentifier Code
3) then i paste the string to my source code
which is the "XXX" of the sample code in that thread.
static string AddonIdentifierString="XXX";
int lRetCode=0;
int errCode=0;
string errMsg= string.Empty;
string connectionStr ="";
link = new SAPbouiCOM.SboGuiApiClass();
connectionStr =Environment.GetCommandLineArgs().GetValue(1).ToString();
link.AddonIdentifier=AddonIdentifierString;
link.Connect(connectionStr);
oApp = link.GetApplication(-1);
vCompany = new SAPbobsCOM.CompanyClass();
string cookie = vCompany.GetContextCookie();
string conStr = oApp.Company.GetConnectionContext(cookie);
vCompany.SetSboLoginContext(conStr);
lRetCode = vCompany.Connect();
4) then i add my add-on using manager role at Add-on admin
5) then i can see my add-on there. it not suppose to be there since i've not installed any of my add-on license for my own add-on.
what steps did i miss? Can someone please advise? Thanks
ps : i'm coding in VBHi,
i think you have to change the license file attributing the number of licensing for your addon, then download it from https://websmp202.sap-ag.de/smb and then install it on SAP License manager, then I think you should give the license for your addon for individual users (example manager)
I hope it helps.
Best regards -
How to get online apps to work with the Verizon DSL modem firewall set at "Medium" level, not "Low?"
How to get online apps to work with the Verizon DSL modem firewall set at “Medium” level? Xbox 360 Live, FTP, and the Windows sntp Time checker native to Windows XP WON’T WORK unless the Verizon firewall is first reset down to “Low.” Then all works well, but I then risk low firewall protection. Setup: · Westell 6100 DSL modem (Software Version: VER:4.04.03.00 Transceiver Revision: 7.2.3.0 Model Name: C90-610015-06), · D-Link DIR-655 wireless router (Hardware Version: A3, Firmware Version: 1.21), For Xbox 360 Live the “canned” port forwarding rule for provided in Verizon’s drop-down list for the Westell 6100 modem forwards ports 88 and 3074 for both TCP and UDP. This does not meet Microsoft’s forwarding recommendations for Xbox 360 Live stated at http://support.microsoft.com/kb/908874. Instead, for the Verizon modem (Westell) I made a new port forwarding rule to comply with those Microsoft instructions. It forwards ports 53, 80 and 3074 for TCP and ports 53, 88 and 3074 for UDP. These same ports are also forwarded in the D-Link router configuration. For FTP, port 21 is also forwarded for TCP and UDP in both modem and router. But they don’t work until I first cripple the Verizon firewall down to “Low.” How to get them to work with the Verizon firewall up to Medium?
While I do not know the answer to your question, BUT since you have this modem and another router - you could just follow.
http://www.dslreports.com/faq/13600
^^
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button. -
How to get exact match when working with Oracle Text?
Hi,
I'm running Oracle9i Database R2.
I would like to know how do I get exact match when working with Oracle Text.
DROP TABLE T_TEST_1;
CREATE TABLE T_TEST_1 (text VARCHAR2(30));
INSERT INTO T_TEST_1 VALUES('Management');
INSERT INTO T_TEST_1 VALUES('Busines Management Practice');
INSERT INTO T_TEST_1 VALUES('Human Resource Management');
COMMIT;
DROP INDEX T_TEST_1;
CREATE INDEX T_TEST_1_IDX ON T_TEST_1(text) INDEXTYPE IS CTXSYS.CONTEXT;
SELECT * FROM T_TEST_1 WHERE CONTAINS(text, 'Management')>0;
The above query will return 3 rows. How do I make Oracle Text to return me only the first row - which is exact match because sometimes my users need to look for exact match term.
Please advise.
Regards,
Jap.But I would like to utilize the Oracle Text index. Don't know your db version, but if you slightly redefine your index you can achieve this (at least on my 11g instance) :
SQL> create table t_test_1 (text varchar2(30))
2 /
Table created.
SQL> insert into t_test_1 values ('Management')
2 /
1 row created.
SQL> insert into t_test_1 values ('Busines Management Practice')
2 /
1 row created.
SQL> insert into t_test_1 values ('Human Resource Management')
2 /
1 row created.
SQL>
SQL> create index t_test_1_idx on t_test_1(text) indextype is ctxsys.context filter by text
2 /
Index created.
SQL> set autotrace on explain
SQL>
SQL> select text, score (1)
2 from t_test_1
3 where contains (text, 'Management and sdata(text="Management")', 1) > 0
4 /
TEXT SCORE(1)
Management 3
Execution Plan
Plan hash value: 4163886076
| Id | Operation | Name | Rows | Bytes | Cost (%CPU)| Time |
| 0 | SELECT STATEMENT | | 1 | 29 | 4 (0)| 00:00:01 |
| 1 | TABLE ACCESS BY INDEX ROWID| T_TEST_1 | 1 | 29 | 4 (0)| 00:00:01 |
|* 2 | DOMAIN INDEX | T_TEST_1_IDX | | | 4 (0)| 00:00:01 |
Predicate Information (identified by operation id):
2 - access("CTXSYS"."CONTAINS"("TEXT",'Management and
sdata(text="Management")',1)>0)
Note
- dynamic sampling used for this statementJust read that you indeed mentioned your db version in your first post.
Not sure though if above method is already available in 9i ...
Message was edited by:
michaels -
I just purchased a 15" Macbook Pro with retina display.
How can I get my webcam to be compatable online with websites such as chatroulette, etc?
I have the latest version of flash, my system is updated, and my camera works on photo booth, skype, etc.
Whenever I try to access sites such as the one above the green light doesn't turn on and nothing happens, what can I do to fix this?Have you tried a PRAM reset?
http://support.apple.com/kb/ht1379
If you look in the audio output port, is there a red light showing. If so, the internal switch is stuck.. Insert the headphones a few times, jiggle a toothpick inside or shot some compressed air to trip the switch. If no success, have the Apple store genius bar technician do it.
Ciao. -
i have a lexmark wireless printer, its connected to my imac via wireless bthome hub connection, works fine, so does my pc laptop. but when it comes to connect my macbook pro aswell it wont work. i have installed lexmark drivers on macbook, i have follwed the wireless connection setup and plugged in via usb port. it says it has connected successfully, but it will not print. i had it connected at one point, but would only print if the imac was on, but now it wont even do that.
please help, it seems like instead of connecting through bthome hub it wants to connect to my imac, how do i change this?Well there would probably be different settings for the wireless.
For example, with a Lexmark printer although I needed to do nothing to get it to work via USB, to get the wifi working I had to use a special setup option for getting the wifi to work on my pc.
You can probably download the manual for your printer from the manufacturers website, and it should tell you how to get it to work with your printer. -
Am I able to upgrade the operating software on my 2009 Macbook Pro to work with Mavericks?
I have a 2009 Macbook Pro with 4 GB of Ram. Am I able to upgrade the software enough to support Mavericks and other software?
Yes, but you have a couple major caveats:
Rosetta is gone:
http://discussions.apple.com/docs/DOC-6271
Many drivers may not work.
And you have to buy 10.6 first, then upgrade to 10.6.8, to get the free 10.9 update, then the 10.9.2 update to avoid the security leaks of the first two versions of 10.9. -
Macbook Pro not working with replacement logic board
Hello everyone! About two months ago, someone spilled tea over my macbook pro. Upon taking it to the Apple store the representative told me that it would cost me over $1,000 to repair it and that I would be better off getting a new one (I know most of you have heard that many times). I inspected the Macbook and I realized that when I tried turning it on the keyboard would not light up and, but the sleep light was on. Furthermore, I heard the hard drive and the fans spinning. The tea only spilled on the right side of the Macbook so I figured that would help me narrow down the issue. The apple representative told me that I needed to replace the logic board so I went and bought a replacement one that was the same model. Before I screwed all the pieces back in, I wanted to try it out and see if it would turn on. Unfortunately I still have the same problem. It seems that the logic board is not the problem, but I am not sure what it might be. I'm pretty sure the CD/DVD drive is damaged, but I don't see why that would prevent the Macbook from turning on. I did a little research and I notice that most people test the graphics card to see if it is working, but I don't know how to do that. I have an older Macbook Pro, the motherboard is model 820-1993-A and I believe the model of the Macbook is A1150. Please help, this macbook was a gift and I don't want to throw it out!
Well I would like to find out what the piece is that is causing me the problem so that I could replace it! I already replaced the most expensive piece and the hard drive seems to be working fine so it doesn't leave many things. I just would like to know how I would be able to check to see if the video card is damaged.
-
How to get ASF format to work with FCP
I have a Neuros 442 DVR that I’m trying to pull footage from and play in Final Cut Pro. The thing is that the format that the DVR records in is ASF and Final Cut Pro will not read that. I have put it in a Windows (yes I know I’m sorry) and it would read it but would not convert it without hesitations it the video. If anyone knows how to do this pleas let me know thanks.
Villi Olafssoni did what you said and dowloaded that from flip4mac and it worked on letting the ASF files work with quicktime but the other thing that we are having a problum with is the glitching in the clips after convertion. (we need to conver to MOV from ASF and we are getting hesatations in the clips. which our clients will not like at all. if you now anything else that would help me out that would be great thanks
Villi O. -
Ref.: Setting up Macbook Pro to work with network printers.
I am tired looking for an answer for my issue. I am 5 hours going in and out of blogs and foruns trying to set my printers on my recently bought Macbook Pro with Mac X (10.6.2).
At home I have a home network with on Windows Vista PC and one Epson TX105 Series printer, and I have a Windows Network at work where I am trying to set a HP Laserjet 1505n.
Both cases my notebook tries to reach the printer without success.
I've added the printer all the ways possible and I couldn't get my Mac to print. I've tried every configuration possible.
Anyone could give me a hand?
Thanks a lot in advance.LuizMarques wrote:
2) Have you tried attaching the second to your Mac and printing from there.
No, I haven't. The Office's network administration does not allow me to do that yet. We scheduled to do that next week. (The other printer is installed at home).
You are very welcome. And on what's above, good, hope it works.
3) On your network, what is the printer attached to?
In my home network, the Epson TX105 is attached to a Windows Vista Home Premium PC ....
I couldn't tell if the printer works when attached to the Mac at home. Yes? Are you able to share files at home with the Vista machine? Here are some Vista settings that are likely to work across the board for you.
1. Select a folder (and your printer) to share, right click on the folder, choose sharing, and, using the remaining menus/options, share the folder with everyone allowing read and write (later, after getting things working, you can change who is allowed to share the folder).
2. Go Control Panel > Network and, turn on file and printer sharing, Turn off public folder sharing, and Turn off password protected sharing (unless sharing won’t occur without turning it on). Turn on allow network access if there is a box to do so (can't remember).
3. Restart (probably not necessary, but I’d do it). -
How to get MacBook Pro to recognize full 1366x768 resolution of Plasma?
When I hook up my MacBook Pro via DVI to my 1366 x 768 pixel Samsung plasma screen, the computer recognizes it as a Samsung PDP at 1024x768. The resulting image is stretched to fit the full 1366 horizontal pixels and thus ruins the aspect ratio. I know that I can switch the display mode on the Samsung to display 4x3 with black bars on the side, but what I really want is for the computer to take advantage of the full 1366x768. How do I do that?
Check your documentation. Most Samsung 1366x768 monitors do not support the full native resolution in DVI mode unless using a specific card to drive them made by PixelPerfect Digital.
I'm not entirely sure why that may be, but it does figure prominently in the product information on the Samsung product site. -
Hi I have a Konica Minolta PagePro 1300W printer. This works with my Windows-based Toshiba laptop but not with my i-Mac. I have the latest (Mountain Lion 10.8.2) OS-X software.
I have installed the printer using 'System Preferences' on my i-Mac and it appears on the list of available printers but documents that I create just don't print.
Can someone please advise me how I get the Konica Minolta PagePro 1300W printer to work with my i-Mac?
Thanks, John LeeLooking at the Konica web site for the PagePro 1300W, I saw the following note.
Please note: This printer is designed to be used in computer operating systems running MS Windows only. Operating systems such as UNIX, Macintosh, or Linux are not supported nor do we have workaround drivers available. Older MS Windows versions, such as Windows 3.1/95/98[pre-SE] and NT 3.51/4.0, are not supported.
So KM are not going to help you. But the LinuxFoundation does provide a workaround that should allow you to print. Have a look at this web page. You will need to install all three packages as per the instructions from that page. -
MacBook Pro now works with wireless encryption
I am offering my two cents. After spending a morning on the phone with TDS and part of the afternoon with apple yesterday, today I finally have my MacBook Pro talking wireless with an encryption key.
My MBP would connect without an encryption key but would not with an encrytion key. The MBP is 2.16GHz model, with 10.4.9 plus all updates; the GW is an Actiontec GT704-WG.
My original encryption key which did not work was 128bit key 112233445566778899aabbccdd. When this key was in the router and entered onto the MBP it would not connect.
When I changed to 64bit encryption and entered an ASCII ABCDE on the router, then on the MBP entered a 64bit key of 4142434445 (the equivalent hexcodes), everything connected.
I have not tried this method with a 128 bit encryption key.
I hope this helps those who can connect without encryption but not with encryption.
Bruce KaiseriCloud technically starts working with Lion, but I recommend Mavericks, because it is a free upgrade (and a more recent one).
Maybe you are looking for
-
Personal File Sharing Quits - Help! I have a deadline!!
I'm having problems with personal file sharing. I have two macs, both dual 2GHz G5s. Computer 1 has all of the work files on it, and when computer 2 tries to connect, it shuts down personal file sharing! Computer 1 can connect to computer 2, but not
-
I recently purchased an Ipod 4G from a family friend. When I set up my account, I originally was going to keep some of the items on it but found they were not appropriate for my 10 yr old. So I reset the IPOD erasing everything and started new. Af
-
I just installed Arch from Opensuse 11 following this guide http://wiki.archlinux.org/index.php/Ins … ting_Linux . I installed Gnome 2.24 desktop through OpenSuse also. However, when I log into Arch, the internet (wired) is not working. I have insta
-
Problem in using the api Hr_Personal_Pay_Method_Api
I am getting the following exception message in the HRSSA workflow and it errors out always. ORA-20001: FLEX-DSQL EXCEPTION: Error Stack Wf_Engine_Util.Function_Call(hum_hr_ss_paymethods.chg_cash_to_deposit, HRSSA, 3717165, 408994, RUN) The above cus
-
Quicktime application not responding after screen recording.
After taping video gameplay of a heavily modded Fallout: New Vegas, pressing the stop button makes the application stop responding altogether. Causing me to force quit as it saves only a couple seconds. It worked for awhile for about four recordings