HOW TO GET MY IPHONE 4S OUT OF BEING STUCK IN HEADPHONES MODE? I TRIED BLOWING IT, I TRIED SUCKING IT AND I TRIED THE QU TIP, ALSO FREEZING AND PLUGGING AND UNPLUGGING THE HEADPHONES. I ALSO RESTORED IT AND PUT IT IN DFU MODE AND STILL NOTHING.
How do i get my iphone 4s out of being stuck in headphones mode. When i dont even have headphones plugged in, it says headphones ringer. I've tried blowing and sucking in the jack, didnt work. I tried using a blowdrier in the jack, didn't work. I also tried putting it in the freezer while in a plastic bag, trying to clean it with a qu tip, and plugging and unplugging the headphones more than 100 times, still nothing and i also restored, reset, and put my iphone in DFU mode, and still nothing seems to work. DOES ANYONE KNOW ANY OTHER WAY I NEED HELP PLEASEEEEEEEE!!!!!!!!!!! ANYONE ANY OTHER WAYS TO FIX IT?!?!??!? That would be very helpful
I had the same problem. I squirted a drop of WD40 in the headphone hole and then used a plastic dental toothpick and twisted it around in the hole. It amazingly worked.
Good luck
Similar Messages
-
How to get an iPhone 4 out of recovery mode?
The restore needed popped up on my phone and also started cutting on and off every 3 or 4 minutes. Intially I tried to restore it through iTunes but it would not stay long enough to be restored. Then I tried to restore it in recovery mode. However the error message 1 and error message 3194 popped up after several attempts. What do those two error message mean?
I'm wanting to take my pictures off of my phone. How can I get my phone out of recovery mode?Disable ALL of your antispyware/antivirus software, open your firewall, and try again. I would aslo disconnect any other USB peripherals.
If that does not work the error 1 would indicate their is hardware damage to you iPhone. You will need to get it serviced. -
So just downloaded 5.0 and it deleted all my contacts, how can I get it all back? I already tryed the "Back Up" or "Restore" and it's still blank on my iphone??
You should have been syncing your contacts to your computer regularly. Just sync them back ot the iphone from your computer.
-
QUESTIONS: I have an iphone 3gs.just updating to ios5. am at the stage where I chose to restore iphone via itunes. sync seems stuck at step 7 of 7: syncing artwork. Is this necessary and if not how do I get around it?
When I use find file http://www.macupdate.com/app/mac/30073/find-file (which does tend to find files that "Finder" can't), it's not coming up with any other itunes library files that have been modified in the past week, which I know it would have been - unfortunately, I don't have a very recent backup of the hard drive. It would be a few months old so it wouldn't have the complete library on it....any ideas? I'm wondering if restarting the computer might help but have been afraid to do so in case it would make it harder to recover anything...I was looking at this thread https://discussions.apple.com/thread/4211589?start=0&tstart=0 in the hopes that it might have a helpful suggestion but it's definitely a different scenario.
-
How do I get my iPhone 4S out of Recovery Mode w/o restoring? (got stuck when upgrading to ios 7)
Last night I upgraded my iPhone 4S to ios 7, and this morning when I went to use it I was stuck in Recovery Mode - How do I get my iPhone 4S out of it w/o restoring? I have photos, contacts, etc Iwant to get off the phone. I tried Tiny Umbrella and RecBoot but no dice. I was not able to get any help from the Apple tech on the phone. They only suggestions offered were to check to see if iPhoto or the Finder would show my device so I could copy over my photos.
Thanks, ChadSee: Resolve iOS update and restore errors - Apple Support
That error usually means that your computer antivirus is blocking the update.
It can also mean that your phone was jailbroken, or your computer was used to jailbreak some iOS device in the past. -
I have a question. For the past week I have not been able to access my iTunes app it always kicks me out. I've turned it off and on and still nothing. I was wondering how can I get it to work or what should I do. Thank you
You need a computer with iTunes and an internet connection
Try:
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
Getting error code 1611 when trying to restore my Ipod. I have tried a forced restore and disabling my computer security and still nothing...ready to throw it out the window at this stage...help!!
Error 1611
This error typically occur when security software interferes with the restore and update process. FollowTroubleshooting security software issues to resolve this issue. In rare cases, this error may be a hardware issue. If the errors persist on another computer, the device may need service.
If you also unsuccessful on another computer then time for an appointment at the Genius Bar of an Apple store. It would see that your iPod needs service as specified in the article. -
How can i get a iphone 3G out of recovery mode without restoring it
Need Help, How can I get a iPhone 3G out of recovery mode without restoring it. it has never been backed up so restoring it will loose all contacts etc.
You can't get it out of recovery mode without restoring it.
If it's in recovery mode, your data's almost certainly gone anyway. -
How do I get my iPhone 5c out of black screen recovery mode?
I have been trying for countless hours and days to get my iPhone 5c out of recovery mode (black screen no apple logo or anything else) the only reason I know it turns on is because the backlight LCD changes color. When I press down on it it leaves a little finger pressure thing. I have tried all of the ways to get it out of DFU mode, Out of Recovery Mode, I have tried restoring it, in which case i get the error 4005,40013 etc. So now I have come here for my last hoorah on trying to get this pile out of recovery mode and the IOS installed and working.
I don't know if this matters or not but, I have recently purchased a screen from ebay, it was an original iPhone screen etc. I have replaced it and as i said the screen works fine. that shouldn't have any problem with the actual software malfunctioning to update, but here is the log! Enjoy!
All help is greatly appreciated and I will do my best to give credit where it is deserved in the future! God Bless!
2014-07-08 23:05:05.000 iTunes[796:707]: restore library built Jan 31 2014 at 16:40:15
2014-07-08 23:05:05.000 iTunes[796:707]: iTunes: iTunes 11.2.2
2014-07-08 23:05:05.000 iTunes[796:707]: iTunes: Software payload version: 11D257 (option key)
2014-07-08 23:05:05.000 iTunes[796:707]: iTunes: Using MobileRestore state machine
[23:05:52.8450] Successfully applied power assertion
[23:05:52.8454] Changing state from 'Idle' to 'Restoring'
[23:05:52.8692] amai: AMAuthInstallSsoInitialize: can't find SSOClient.framework
[23:05:52.8695] requested restore behavior: Erase
[23:05:52.8698] requested variant: Erase
[23:05:52.8822] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:53.4330] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is True
[23:05:53.4334] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreLogo" Digest = "<CFData 0x6000002b7ac0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4339] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreDeviceTree" Digest = "<CFData 0x6000002b7460 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4344] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreKernelCache" Digest = "<CFData 0x6000000bf680 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4349] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RestoreRamDisk" Digest = "<CFData 0x6000002a13e0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4354] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBEC" Digest = "<CFData 0x6080000b40a0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4359] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBSS" Digest = "<CFData 0x6000002a88e0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4364] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "KernelCache" Digest = "<CFData 0x6000002af720 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4369] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "LLB" Digest = "<CFData 0x6000002b6380 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4374] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "AppleLogo" Digest = "<CFData 0x6000000bcaa0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4379] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryCharging1" Digest = "<CFData 0x6000002b1760 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4384] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryFull" Digest = "<CFData 0x6000002ac240 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4388] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryPlugin" Digest = "<CFData 0x6000002b0bc0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4392] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryCharging0" Digest = "<CFData 0x6000002b5cc0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4396] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryLow0" Digest = "<CFData 0x6000002b0740 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4400] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "BatteryLow1" Digest = "<CFData 0x6000002aa980 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4405] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "RecoveryMode" Digest = "<CFData 0x6000002b1340 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4408] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "DeviceTree" Digest = "<CFData 0x6000002b13a0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4412] amai: _AMAuthInstallBundleCreateServerRequestDictionary: personalizing "iBoot" Digest = "<CFData 0x6100000b5600 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}"
[23:05:53.4416] amai: _AMAuthInstallBundleCreateServerRequestDictionary: using UniqueBuildID <CFData 0x6000008531a0 [0x7fff72885f00]>{length = 20, capacity = 20, bytes = 0x<<<<<<<<<<<<<<<<<<UDID>>>>>>>>>>>>>>>>>>}
[23:05:53.4419] amai: AMAuthInstallRequestSendSync: SSO function returned NULL, SSO disabled.
[23:05:53.4422] amai: AMAuthInstallDebugWriteObject: debug object written: file://localhost/tmp/PersonalizedBundle_E7EE0982-00C0-4513-B599-39C008B08D9C/am ai/debug/tss-request.plist
[23:05:53.4425] amai: AMAuthInstallHttpMessageSendSync: httpRequest=<CFHTTPMessageRef 0x61000016fc00(0x61000016fc10)> { POST request, priority -1, url http://gs.apple.com:80/TSS/controller?action=2 }
[23:05:53.9574] amai: AMAuthInstallRequestSendSync: received tss response (server version: 2.1.0)
[23:05:53.9640] amai: AMAuthInstallDebugWriteObject: debug object written: file://localhost/tmp/PersonalizedBundle_E7EE0982-00C0-4513-B599-39C008B08D9C/am ai/debug/tss-response.plist
[23:05:53.9676] amai: _AMAuthInstallBundlePopulatePersonalizedBundle: no entry in manifest found for "Diags"
[23:05:53.9709] iBoot build-version = iBoot-1940.10.58
[23:05:53.9716] iBoot build-style = RELEASE
[23:05:53.9720] requested restore behavior: Erase
[23:05:53.9731] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:53.9735] requested restore behavior: Erase
[23:05:53.9747] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:53.9751] unable to open device_map.txt: No such file or directory
[23:05:53.9937] found device map entry for 0x00008950 0x0000000a. boardConfig=n48ap platform=s5l8950x
[23:05:53.9941] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[23:05:53.9945] DeviceRequest failed: 0xe000404f
[23:05:53.9949] command device request for 'getenv radio-error' failed: 2008
[23:05:53.9952] radio-error not set
[23:05:53.9955] unable to open device_map.txt: No such file or directory
[23:05:53.9958] <Recovery Mode Device 0x60800014bf20>: production fused device
[23:05:53.9961] requested restore behavior: Erase
[23:05:53.9965] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:53.9968] requested restore behavior: Erase
[23:05:53.9977] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:54.0270] <Recovery Mode Device 0x60800014bf20>: operation 4 progress -1
[23:05:54.0553] bootstrapping restore with iBEC
[23:05:54.0557] requested restore behavior: Erase
[23:05:54.0568] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:54.0673] <Recovery Mode Device 0x60800014bf20>: operation 31 progress -1
[23:05:55.0687] <Recovery Mode Device 0x60800014bf20>: Recovery mode succeeded
[23:05:55.0692] Finished Recovery Restore Phase: Successful
[23:05:55.1899] Recovery mode device disconnected
[23:05:55.1903] Device removed when in state Restoring, moving device to transition state
[23:05:55.1906] Changing state from 'Restoring' to 'Transitioning'
[23:05:55.1909] Creating timer to monitor transition
[23:05:57.3207] Recovery mode device connected
[23:05:57.3210] Transitioning device returned, continuing restore.
[23:05:57.3213] Canceling timer
[23:05:57.3217] Changing state from 'Transitioning' to 'Restoring'
[23:05:57.3220] requested restore behavior: Erase
[23:05:57.3223] requested variant: Erase
[23:05:57.3227] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:57.6937] amai: _AMAuthInstallBundleCreateServerRequestDictionary: withApTicket is False
[23:05:57.6941] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreLogo"
[23:05:57.6945] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreDeviceTree"
[23:05:57.6950] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreKernelCache"
[23:05:57.6953] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RestoreRamDisk"
[23:05:57.6957] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBEC"
[23:05:57.6961] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "iBSS" has been previously personalized; skipping it
[23:05:57.6964] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "KernelCache"
[23:05:57.6968] amai: _AMAuthInstallBundleCreateServerRequestDictionary: entry "LLB" has been previously personalized; skipping it
[23:05:57.6971] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "AppleLogo"
[23:05:57.6975] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging1"
[23:05:57.6978] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryFull"
[23:05:57.6981] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryPlugin"
[23:05:57.6984] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryCharging0"
[23:05:57.6987] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow0"
[23:05:57.6991] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "BatteryLow1"
[23:05:57.6994] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "RecoveryMode"
[23:05:57.6997] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "DeviceTree"
[23:05:57.7000] amai: _AMAuthInstallBundleCreateServerRequestDictionary: not personalizing "iBoot"
[23:05:57.7004] amai: _AMAuthInstallBundleCreateServerRequestDictionary: nothing to be done
[23:05:57.7007] iBoot build-version = iBoot-1940.10.58
[23:05:57.7011] iBoot build-style = RELEASE
[23:05:57.7015] requested restore behavior: Erase
[23:05:57.7018] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:57.7022] requested restore behavior: Erase
[23:05:57.7025] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:57.7029] unable to open device_map.txt: No such file or directory
[23:05:57.7033] found device map entry for 0x00008950 0x0000000a. boardConfig=n48ap platform=s5l8950x
[23:05:57.7036] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[23:05:57.7040] DeviceRequest failed: 0xe000404f
[23:05:57.7043] command device request for 'getenv radio-error' failed: 2008
[23:05:57.7047] radio-error not set
[23:05:57.7050] unable to open device_map.txt: No such file or directory
[23:05:57.7054] <Recovery Mode Device 0x60800014d1b0>: production fused device
[23:05:57.7057] requested restore behavior: Erase
[23:05:57.7061] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:57.7065] requested restore behavior: Erase
[23:05:57.7068] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:57.7325] <Recovery Mode Device 0x60800014d1b0>: operation 4 progress -1
[23:05:57.7714] unable to open device_map.txt: No such file or directory
[23:05:57.7719] found device map entry for 0x00008950 0x0000000a. boardConfig=n48ap platform=s5l8950x
[23:05:57.7722] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[23:05:57.7726] requested restore behavior: Erase
[23:05:57.7733] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:57.7738] requested restore behavior: Erase
[23:05:57.7750] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:57.7754] <Recovery Mode Device 0x60800014d1b0>: operation 42 progress -1
[23:05:57.7758] requested restore behavior: Erase
[23:05:57.7767] amai: AMAuthInstallBundleCopyBuildIdentityForVariant: No baseband chipid reported. Will match Build Identity based on ap chipid and boardid only.
[23:05:58.8029] <Recovery Mode Device 0x60800014d1b0>: operation 5 progress -1
[23:05:59.1074] unable to open device_map.txt: No such file or directory
[23:05:59.1078] found device map entry for 0x00008950 0x0000000a. boardConfig=n48ap platform=s5l8950x
[23:05:59.1082] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[23:05:59.1086] DeviceRequest failed: 0xe000404f
[23:05:59.1089] command device request for 'getenv ramdisk-delay' failed: 2008
[23:06:00.7244] <Recovery Mode Device 0x60800014d1b0>: operation 6 progress -1
[23:06:01.7350] <Recovery Mode Device 0x60800014d1b0>: operation 7 progress -1
[23:06:02.0286] <Recovery Mode Device 0x60800014d1b0>: operation 8 progress -1
[23:06:02.0290] unable to open device_map.txt: No such file or directory
[23:06:02.0294] found device map entry for 0x00008950 0x0000000a. boardConfig=n48ap platform=s5l8950x
[23:06:02.0298] _AMRestoreCopyDeviceMapPlistEntryForHardware: firmwareDirectory not in options
[23:06:02.0301] <Recovery Mode Device 0x60800014d1b0>: operation 9 progress -1
[23:06:02.0305] <Recovery Mode Device 0x60800014d1b0>: Recovery mode succeeded
[23:06:02.0308] Finished Recovery Restore Phase: Successful
[23:06:03.2217] Recovery mode device disconnected
[23:06:03.2220] Device removed when in state Restoring, moving device to transition state
[23:06:03.2223] Changing state from 'Restoring' to 'Transitioning'
[23:06:03.2226] Creating timer to monitor transition
[23:06:29.9952] Restore completed, status:4013
[23:06:29.9952] Failure Description:
[23:06:29.9952] Depth:0 Error:Unexpected device state 'Recovery' expected 'RestoreOS'I ran into the problem you have after trying to update to 7.1.2 the phone updated, but got stuck in recovery mode, and none of the reset methods worked. I did some searching and came up with a simple method, and it got me out of the loop.
Once i used this app, My phone booted and The update was in place.
http://jaxov.com/2010/05/recboot-iphone-recovery-mode/ -
Why we still dont have sound notifications on iPhone??? This started in September with the launch of the new IOS and iPhone 5... I've been waiting and waiting and still nothing... How hard can this be to fix????????
Hi guys... The notifications i'm speaking about are everything that happens on our facebook. The only exception where i get notifications is if someone actually use my name on a post, then i have a notification. Now, if it is a post on my wall, a comment on one of my photos or even a like, there is no sound or vibration at all.
Also, when i say "We" is bacause there are a few users complaining about the same. There are some other forums, specially on facebook about this. What happens is that facebook blocks some of those groups.
One more thing is i did try all possible things to make sure i was doing the right things in order to have notifications. Slider is obviously not in mute position, notifications sounds are on on facebook settings on main settings and also inside the app they are on. Did try to switch everything off and reboot then change again. Did restore the iPhone as new a couple of times. And like i said, if someone actually write my name i will have sound notification...
Anyway, many thanks for your help -
I would like to know how to get my iphone on if it goes into a no service mode and shows as invalid sim, I would like to know how to get my iphone on if it goes into a no service mode and shows as invalid sim
actually I found the solution :
http://www.igeneration.fr/itunes/astuce-votre-historique-d-achats-itunes-12056
it's in french, but the images and google translate will be enough
hope that helps for the others having the same kinda problem -
I have lose my iphone4 box and my i phone4 is freez how i get my iphone serial no
i have lose my iphone4 box and my i phone4 is freez how i get my iphone serial no
Sorry duh. You said your phone is frozen. Sorry cant help. Did you try pressing and holding both the sleep and home buttons at the same time for 20 seconds? That sometimes is all you need to do to unfreeze the phone. Make sure it's charged fully too.
-
How to get this report format out ?
Hello all experts,
Sample table creations like the following. Note checkno under xcheck table is not unique. Have tried pivotting the xcheck table then link pivoted xcechk with xcert using certno and invno but this willl end up getting duplicate records. Can u please help ? Basically I am stuck at how to get that vendor name out on the report
create table xcert(
certseq number primary key,
certno varchar2(5) not null,
vendor varchar2(25));
create table xcheck(
checkseq number primary key,
checkno varchar2(8) not null,
invno varchar2(100);
Xcert Data
certseq certno vendor
1 C1001 BP GAS
2 C1002 BUG PEST CONTROL
3 C1003 BP GAS
4 C1004 BP GAS
5 C1005 WILLIES BESTxcheck Data
checkseq checkno invno
1 EF500001 C1001,C1003,C1004
2 EF500002 C1002
3 EF500002 C1005Looking for a following report format
checkno invno vendor
EF500001 C1001,C1003,C1004 BP GAS
EF500002 C1002 BUG PEST CONTROL
EF500002 C1005 WILLIES BEST Thank you
MunsharHi, Munshar,
MunSharmi wrote:
Frank,
"I don't see why you would need another column. What would you need to store, or retrieve, that a table like this wouldn't allow?
Notice my orignal xcheck table data plus a check date column
{code}
checkseq checkno invno checkdate
1 EF500001 C1001,C1003,C1004 11/01/2010
2 EF500002 C1002 12/10/2010
3 EF500002 C1005 01/01/2011
{code}Sure, if you have other data that you haven't mentioned yet, then you need other columns, and maybe even other tables, to store that data.
Talking about this would be a lot easier if you described what you were trying to model in these tables, and what the different entities are.
after nomalization
{code}
seq(PK) checkseq checkno invno checkdate
1 1 EF500001 C1001 11/01/2010
2 1 EF500001 C1003 11/01/2010
3 1 EF500001 C1004 11/01/2010
4 2 EF500002 C1002 12/10/2010
5 3 EF500002 C1005 01/01/2011
{code}What do checkseq and checkdate represent? What is the realtionship between them? If there is another row with checkseq=3, will it necessarily have checkdate=01/01/2011? If there is another row with checkdate=01/01/2011, will it necessarily have checkseq=3?
Shouldn't I need to have the extra seq(PK), then use check seq to group the data report to meet users' target format ? Please adviseIt depends on what your entities are. If you explain that, then perhaps I can give some advice about how to model them.
In general, every type of entity requires a separate table. It looks like xcert represents one kind of entity, uniquely identified by certno. I assume there is some other kind of entity, uniquely identified by checkno, and that you have a table for that which you haven't needed to show in this thread.
Are you saying that there's some other entity, that is uniquely identified by checkseq? If so, it probably needs a table of it's own.
Every table should have a primary key. I had assumed that checkseq only served as the primary key of the xcheck table. If it serves some other purpose, then yes, you would need another column.
Many-to-many relationships usually require a separate table. I was guessing that xcheck was intended to record a many-to-many realtionship between xcert and some other table. Guessing is not always the best way to solve problems. I think it would be better if you explained what you want to do, rather than have me guess at it.
So far, what you've shown is analagous to an order entry system. One kind of entity is customer, another is supplier. Say you're running a company that sells products from many suppliers to many customers. There is a many-to-many relationship between customers and suppliers. Any customer may buy from many suppliers; any supllier may sell to many cutomers. You may have an orders table that keeps track of that many-to-many relationship. You may also have another entity, salesman, that also has many-to-many relationships with customers and suppliers. Depending on what exactly you consider an "order", there are lots of different ways to model this. Can a single order involve many customers? Can a single order involve many suppliers? Can a single order involve many salesmen? If an order always involves one customer buying from one supplier using one salesman, then you may only need four tables. If the situation is more complicated, then you may need more tables. -
Ipod Touch 1st generation: blank white screen - I tried holding both buttons and connecting it to the computer, restoring it, and still nothing. What else can I do? I did not drop it in water.
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
If I'm Getting my iPhone an Out-of-Warranty Replacment
If I'm Getting my iPhone an Out-of-Warranty Replacment for a cracked screen, do I need to tell them any information? I live in Edmonton, Alberta, Canada and going to West Edmonton Mall to have an out-of-warranty replacment.
I'm assuming this is being done by Apple. Since you're getting a replacement iPhone, you obviously have to provide the them info they request regarding your broken phone and will have to update your carrier with the new info such as the IMEI #.
Maybe you are looking for
-
To import photos from Iphone to mac is a strange thing.
There are different ways to import the Iphone pictures to the mac but the result is a strange thing. 1. way over the osx tool digital pictures. result with osx Lion 1.1 GB (with the osx Lion it is 3.8 GB with the same Iphone and pictures) 2. way with
-
I am practicing SAP FICO configuration.... Can anyone give me an example of FI drill down reporting like financial statemnet comparision and also for profit center reporting ....jus some simple example to get the idea of drill down reports.
-
Pasting attributes not working properly in FCPX 10.1
I have an ongoing project in which I use the paste attributes command frequently. I've noticed in 10.1 that the paste attributes doesn't work properly. In particular the trim and possition attributes. When I paste the attributes, the image is trimmed
-
F4M document contains errors - URL missing from Media tag
I feel like I'm getting close to finally get a live stream to work correctly in 4.5 I can see the streams being recorded in the following directories C:\FMSHOME\applications\livepkgr\streams\_definst_\liveevent1 C:\FMSHOME\applications\live
-
Hello All, User A has substituted User B in the worklist. When User A tries to view the "Items on behalf of" - User B, he is able to see the items. But after 10 mins, these workitems disapper and messgae "No item to display" is shown. If User A close