How to get Network Printing to work with Brother!!

So i have my BROTHER DCP-7020 printer connected to my Windows machine and i've been sharing the printer on the network with my old iMac 24' which prints perfectly. Now i have the 27' imac and i have no idea why it won't do printing via network, plugging in USB works fine, i've installed the driver but it doesn't look like it did anything. It just worked on my 24' without any hassle, it gets detected in the "Printer Settings" automatically and i dont recall doing anything to get it to work before.
Can anyone give me some tips of why it won't print and what I need to do in order to get network printing to work on my new Mac?
By the way BOTH MACHINE runs SNOW LEOPARD.
Thanks in advance.

Here's the troubleshoot: http://support.apple.com/kb/HT1404
And here is the manual method: http://support.apple.com/kb/HT3049
Hope this helps!

Similar Messages

HT3669 Hi I have a Konica Minolta PagePro 1300W printer. This works with my Windows-based Toshiba laptop but not with my i-Mac. Can someone please advise me how I get the printer to work with my i-Mac? I have installed it but documents don't print. Thanks

Hi I have a Konica Minolta PagePro 1300W printer. This works with my Windows-based Toshiba laptop but not with my i-Mac. I have the latest (Mountain Lion 10.8.2) OS-X software.
I have installed the printer using 'System Preferences' on my i-Mac and it appears on the list of available printers but documents that I create just don't print.
Can someone please advise me how I get the Konica Minolta PagePro 1300W printer to work with my i-Mac?
Thanks, John Lee

Looking at the Konica web site for the PagePro 1300W, I saw the following note.
Please note: This printer is designed to be used in computer operating systems running MS Windows only. Operating systems such as UNIX, Macintosh, or Linux are not supported nor do we have workaround drivers available. Older MS Windows versions, such as Windows 3.1/95/98[pre-SE] and NT 3.51/4.0, are not supported.
So KM are not going to help you. But the LinuxFoundation does provide a workaround that should allow you to print. Have a look at this web page. You will need to install all three packages as per the instructions from that page.

How do I get the printer to work with AirPort?

I have had my printer connected via USB cable to the AirPort for a while, but recently when I had to disconnect the printer for some home improvement, I ended up with problems.
Upon reconnecting the printer to the AirPort, I started receiving this message:
USB Power
A device connected to this Apple Wi-Fi base station's USB port requires more power than this Apple Wi-Fi base station can provide. Plug the device into a power supply if possible, or connect it to a powered USB hub.
My printer is connected to a power source, but I still cannot print to it. I can see the printer when I send something to be printed, but it will not actually print.
Does anyone have any ideas on how to get my printer to work again?

Thanks for the detail. The dash separates the "main" and "guest" network.
There are a number of settings that are 2.4 GHz on both networks. The only time the dash separates 5 GHz and 2.4 GHz is on the last 3 settings.
Since the printer specifications available on the HP site show it is a b/g device only, I suspect that the printer does not like the current guest setting of 802.11 b/g/n you are currently using, which is also what it would be if the AEBS was set on Automatic.
Try the following setting:
802.11n only 5 GHz - 802.11 b/g
It's really the only choice that would keep the 5 GHz that you want on the "main" network and possibly allow the printer to connect. Unfortunately, the optimal choice for range and speed is not the setting that you may need to work with the printer.
If the printer still won't connect, I would call it a day and when it comes time for a new printer, look first for an ethernet device or at least an "n" device that will handle 5 GHz if you want a wireless printer. The advantage of an ethernet printer would be that it would also work over your wireless.
Please post back on your findings.

Update to kichat: FAQ 2 - How to get my router to work with iChat?

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

kichat: FAQ 2 - How to get my router to work with iChat? December 2008 version 3
(Note to Hosts. to be removed on acceptance. Please use this to replace http://discussions.apple.com/thread.jspa?threadID=121775 )
Getting your router started with iChat.
Appropriate for using iChatAV 2 upwards. Edits have been made for iChat 4
Glossary for this FAQ
Routers: Any configurable device that sits between your computer and the internet link you have. This includes Modems that Route as well as "routers"
Routers seem to fall into two categories
Those that work straight from the box. See Apple Article HT1787
NOTE :This Article has not been updated in content since Jan 04 Only being changed to an Article from the Previous Doc listing
Even then some list that they need tweaks.
and those that do not.
This post will deal with what you may need to look at.
First off make sure your device is acting as a DHCP server. (if you are already on the internet you may not have to bother with this.)
Check in the Tiger System Preferences > Network Preference Pane, in the "Built in Ethernet" option from the "Show" drop down list.
In Leopard the Networks are listed on the left with icons. The Airport Option will need you to access the Advance Button for the Next bit.
Make sure the TCP/IP tab is the 'front' one. You should be able to see Configure IPv4 and it most likely reads Using DCHP. Make a note of your IP address. It will start 10.xxx.xxx.xxx or 192.168.xxx.xxx (the 'x' s will stand for any number between 1 and 255). The range 172.16.xxx.xxx is also a possible value at this point. Rarely used, but it is part of the RFC for Address Allocation for Private Internets.
Your router is most likely to be configurable from your browser. You will need to find the IP address to type into the browser from any Readme or PDF files that came on the install disk or visit the makers website and download a manual.
The Port Forward.com site lists many devices and clicking on one will take you to a list of Applications. This iChat will open an page that will start by telling you the defaults to access the device
Opening or Allowing ports. Several Methods not all devices have all of them.
DMZ (Demilitarised Zone)
This is a less secure setting that basically opens all ports and points the incoming data to your computer. (not helpful if you have more than one computer on your LAN). It can be considered as an extreme form of Port Forwarding
Port Forwarding (also Virtual Server or Pin Holes)
These settings are usually found in an Advanced setting.
You may need to set an incoming IP address (Usually 0.0.0.0 to any outside server), a port that data will arrive on, the Inside computer's IP address (your computer) and the port it will deal with the data on and the protocol it will use.
See this pic for an example of the description above.
In this example shows that on some Port AND Protocols need to be listed.
iChat uses TCP and UDP so some devices will need the ports listed one by one and some settings done twice, once for each protocol. The example above has a "Both" setting
See Apple Article HT1507 Previously Doc 93208 for more information. This is the Tiger iChat 3 list. The same ports are needed for Leopard except for these changes
My Note 2:
On the first link Note 1 under tables in that link would be better if it read:
" 1. All iChat AV traffic is UDP -
except for ports 5190 and 5298, which need to be open for both TCP as well;
and 5220, 5222, which need to be open for TCP only. "
Note 2
GoggleTalk needs port 5223 on TCP. Also note the Server name for iChat 3 set ups
UPnP Universal Plug n Play.
This is a simple Plug and Play type of setting. iChat can find it's own way through a router if the device has this capability.
By Not doing Port Forwarding, Triggering or DMZ and enabling UPnP the application is allowed to control the modem and the ports that are open.
They close after the application has finished with them on a timed basis.
On some devices the number of "hops" (how far away the UPnP can be "seen") can be reduced from a default of 4)
Trigger Ports
Some devices offer a security measure that works by a first or trigger port receiving a data packet and then opening further ports when accepted.
The first port for incoming Video or Audio invites is port 5678.
Pre iChat 4
When you click on the invite window the process moves in to port 5060 (so these will need to be opened by the trigger port) for negotiating the final group of ports from the group of 20 (16384-16403 These will need to open when the trigger says so as well). Therefore port 5678 triggers ports 5678, 5060, 16384-16403. All on UDP. Port 5190 neeeds to trigger port 5190 for both TCP and UDP.
See this variation where only the ports listed above are completed.
The other single ports need to be set one by one in addition. (5220,5222, 5223 5297, 5298, 5353)Replace
iChat 4
The port used in IChat 4 is port 16402 instead of port 5060. The group of 20 ports is reduced to 10 (16393-16402). This is because all the In and Out Audio and Video data is on one port. Other that than the settings are the same.
At this time there is no Info on the ports the Screen Sharing in iChat 4 uses.
Wireless
Here you will have to read around but this Apple Article TA25949 Previously Doc 58514 might be a good starting place.
Essentially whether you are wireless or Ethernet to your routing device makes very little difference to the way you do things.
Your computer will get two IPs from a DHCP server if you are connected by both methods. (iChat does not like this)
Multiple devices
Make sure only one is acting as a DHCP server. Make sure wireless devices are bridged properly.
Further Help
I have found that this site (ADSLGuide) to be helpful.
It is British based but I have linked you to the Apple Related Discussions Forum.
Eliminating Problems on my Personal web pages.
The ports and their function within iChat. (my personal Web pages again)
This is not a step by step approach. You will have to read around the information about your device.
Collected FAQs and Expansions: Index Page Based on FAQs here by EZ Jim and myself
Also http://www.portforward.com/routers.htm for instructions with Pics on Port Forwarding and access info as mentioned earlier.
Click on your device.
Select iChat on the next page.
Follow the info on the next.
This site is godd for finding out the Default IP to use in a web browser and the default User ID and Passwords needed to do so.
Gives you a chance to look at at pics to give clues to where some of these other things are.
With thanks to Macmuse for comment on the Original (Aug 23rd 2004)
and to EZ Jim for his work on iSights on my web pages.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
9:51 PM Saturday; December 6, 2008

How to get this script to work with different browser

Do you guys know how to get this script to work with mozilla firefox?
do shell script "open -a safari 'https://login.binck.nl/klanten/Login.aspx?ReturnUrl=%2fklanten%2fdefault.aspx'"
tell application "Safari"
activate
          tell document 1
                    repeat until ((do JavaScript "location.host") is "login.binck.nl")
                              delay 1
                    end repeat
do JavaScript"document.getElementById('ctl00_Content_Gebruikersnaam').value='sim';document.ge tElementById('ctl00_Content_Wachtwoord').value='password';window.open(document. g etElementById('ctl00_Content_LoginButton').href, '_self', 'true');"
          end tell
end tell
Thank you so much in advance:)

That isn't possible. Firefox's AppleScript dictionary doesn't contain anything which can be used to manage JavaScripts.
(63741)

How to get my Addon to work with the license key?

Hi,
Can someone tell me how to get the Addon to work with the license key?
I've follow the steps as stated in this thread:
[Re: SBO 2005 A - How do I get a Connection string from SAP B1.|Re: SBO 2005 A - How do I get a Connection string from SAP B1.]
1) i've registered a BASIS key and get a 'BASISXXXXXX" string
2) then i paste my BASIS key in "Solution" of Add-On Indentifier Generator and generate the Add-On Indentifier Code
3) then i paste the string to my source code
which is the "XXX" of the sample code in that thread.
static string AddonIdentifierString="XXX";
int lRetCode=0;
int errCode=0;
string errMsg= string.Empty;
string connectionStr ="";
link = new SAPbouiCOM.SboGuiApiClass();
connectionStr =Environment.GetCommandLineArgs().GetValue(1).ToString();
link.AddonIdentifier=AddonIdentifierString;
link.Connect(connectionStr);
oApp = link.GetApplication(-1);
vCompany = new SAPbobsCOM.CompanyClass();
string cookie = vCompany.GetContextCookie();
string conStr = oApp.Company.GetConnectionContext(cookie);
vCompany.SetSboLoginContext(conStr);
lRetCode = vCompany.Connect();
4) then i add my add-on using manager role at Add-on admin
5) then i can see my add-on there. it not suppose to be there since i've not installed any of my add-on license for my own add-on.
what steps did i miss? Can someone please advise? Thanks
ps : i'm coding in VB

Hi,
i think you have to change the license file attributing the number of licensing for your addon, then download it from https://websmp202.sap-ag.de/smb and then install it on SAP License manager, then I think you should give the license for your addon for individual users (example manager)
I hope it helps.
Best regards

How to get online apps to work with the Verizon DSL modem firewall set at "Medium" level, not "Low?"

How to get online apps to work with the Verizon DSL modem firewall set at “Medium” level? Xbox 360 Live, FTP, and the Windows sntp Time checker native to Windows XP WON’T WORK unless the Verizon firewall is first reset down to “Low.” Then all works well, but I then risk low firewall protection. Setup: · Westell 6100 DSL modem (Software Version: VER:4.04.03.00 Transceiver Revision: 7.2.3.0 Model Name: C90-610015-06), · D-Link DIR-655 wireless router (Hardware Version: A3, Firmware Version: 1.21), For Xbox 360 Live the “canned” port forwarding rule for provided in Verizon’s drop-down list for the Westell 6100 modem forwards ports 88 and 3074 for both TCP and UDP. This does not meet Microsoft’s forwarding recommendations for Xbox 360 Live stated at http://support.microsoft.com/kb/908874. Instead, for the Verizon modem (Westell) I made a new port forwarding rule to comply with those Microsoft instructions. It forwards ports 53, 80 and 3074 for TCP and ports 53, 88 and 3074 for UDP. These same ports are also forwarded in the D-Link router configuration. For FTP, port 21 is also forwarded for TCP and UDP in both modem and router. But they don’t work until I first cripple the Verizon firewall down to “Low.” How to get them to work with the Verizon firewall up to Medium?

While I do not know the answer to your question, BUT since you have this modem and another router - you could just follow.
http://www.dslreports.com/faq/13600
^^
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

How to get Canon Printer to work wired?

I have a canon wireless printer. I just got a cable for it as i want to not use wifi to print from my computer.
How do i get my Canon printer to work with the cable in it.
computer is a IMAc
printer canon MP560 colour
I have cable in it now. How do i get it to work wired to computer? thanks

System Preferences - Printing & Scanning highlight your printer and right click and choose Reset Printing System. Next turn off the printer, then restart the computer in Safe Mode which will clear some caches. To restart in Safe Mode, simply hold down the Shift Key when you hear the startup tone until a progress bar appears. Then shut down the computer, connect the USB cable from the printer to the computer and start the compute normally, then turn on the printer and your iMac should find it. If your computer does not find the printer follow Apple's instructions for doing so.

How to get exact match when working with Oracle Text?

Hi,
I'm running Oracle9i Database R2.
I would like to know how do I get exact match when working with Oracle Text.
DROP TABLE T_TEST_1;
CREATE TABLE T_TEST_1 (text VARCHAR2(30));
INSERT INTO T_TEST_1 VALUES('Management');
INSERT INTO T_TEST_1 VALUES('Busines Management Practice');
INSERT INTO T_TEST_1 VALUES('Human Resource Management');
COMMIT;
DROP INDEX T_TEST_1;
CREATE INDEX T_TEST_1_IDX ON T_TEST_1(text) INDEXTYPE IS CTXSYS.CONTEXT;
SELECT * FROM T_TEST_1 WHERE CONTAINS(text, 'Management')>0;
The above query will return 3 rows. How do I make Oracle Text to return me only the first row - which is exact match because sometimes my users need to look for exact match term.
Please advise.
Regards,
Jap.

But I would like to utilize the Oracle Text index. Don't know your db version, but if you slightly redefine your index you can achieve this (at least on my 11g instance) :
SQL> create table t_test_1 (text varchar2(30))
2 /
Table created.
SQL> insert into t_test_1 values ('Management')
2 /
1 row created.
SQL> insert into t_test_1 values ('Busines Management Practice')
2 /
1 row created.
SQL> insert into t_test_1 values ('Human Resource Management')
2 /
1 row created.
SQL>
SQL> create index t_test_1_idx on t_test_1(text) indextype is ctxsys.context filter by text
2 /
Index created.
SQL> set autotrace on explain
SQL>
SQL> select text, score (1)
2    from t_test_1
3   where contains (text, 'Management and sdata(text="Management")', 1) > 0
4 /
TEXT                             SCORE(1)
Management                              3
Execution Plan
Plan hash value: 4163886076
| Id | Operation                   | Name         | Rows | Bytes | Cost (%CPU)| Time     |
|   0 | SELECT STATEMENT            |              |     1 |    29 |     4   (0)| 00:00:01 |
|   1 | TABLE ACCESS BY INDEX ROWID| T_TEST_1     |     1 |    29 |     4   (0)| 00:00:01 |
|* 2 |   DOMAIN INDEX              | T_TEST_1_IDX |       |       |     4   (0)| 00:00:01 |
Predicate Information (identified by operation id):
   2 - access("CTXSYS"."CONTAINS"("TEXT",'Management and
              sdata(text="Management")',1)>0)
Note
   - dynamic sampling used for this statementJust read that you indeed mentioned your db version in your first post.
Not sure though if above method is already available in 9i ...
Message was edited by:
michaels

Can't get out.print to work with XML jsp tags

<jsp:scriptlet>
if(ErrorTrap == true) {
out.println("<tr><td colspan=\"center\" align=\"center\">There was" an error while processing the form</td></tr>");
ErrorTrap = false;
</jsp:scriptlet>
I can't get this script to work with the XML stype jsp tags. It keeps telling me the <jsp> tags are untermintaed. Is there a special trick to fix this or do I have to use the non-XML type tags?

Sorry, I didn't mean to put the extra " in the out.println text string. :-/

How do I get my printer to work with my iPhone/ipad wirelessly

how do I get my printer epson workforce 610 wirless to work from my iphone/ipad? I downloaded the epson printer app.

Maryannebrabander,
Your comment " ... It was printing great until I did this upgrade." brought to mind a thought:
If you're ever in the SIlicon Valley area of California, specifically Mountain View, CA, I strongly recommend a visit to the Computer History Museum there. This page from the Museum website shows a Calcomp plotter advertisement from 1969:
http://www.computerhistory.org/revolution/mainframe-computers/7/161/689
My question to you is should the iPhone be able to print to the Calcomp plotter? If not, exactly how old would you have a printer (or plotter) be before you dropped support for it? If you ever do drop support, then that would occur at some discrete time - one day it would work, then something would be updated and it would no longer work.

We have a Lexmark Pinnacle Pro901 and cannot get the printer to work with airport express - any suggestions?

Can anyone give us suggestions on how to get our Lexmark Pinnacle Pro 901 to work with airport express? We cannot get airport express to recognize the printer.

Refresh all your devices before reconfiguring printer to connect to your computer.
a Shutdown computer
b Pull out printer power cord from the socket. Let it stay for at least 30 seconds then plug it back.
c Powercycle your router (unplug your router for at least 30 then plug it back. This will not change the settings of the router. This will just refresh the device)
d Once router is ready , put back brick at the back of the printer to turn it on
e Wait one minute
f Turn on computer
Repair your disk permission: http://bit.ly/OeD7U3
Run Cleanup tool http://bit.ly/vnukXY
Download updated driver from Lexmark website http://bit.ly/ToA1fo
Run firmware update http://bit.ly/AcNqbg

How to get LG G3 to work with SYNC in FORD F150

Is there something different i should be doing to get lg g3 to work in my f150 for handsfree calls used sync shpplemental guide to get it to work no results please provide detailed instructions or a link to get instructions

Hi Ed, I think you will need to check with Ford support on this.
When I look at the device compatibility page, Ford says the regular SYNC works with the G3 a bit differently depending on the carrier:
Works on AT&T, Sprint, T-Mobile and Verizon:
Automatic Phonebook Download
Caller ID
SMS Text Messaging
Call History Download
Bluetooth Audio Streaming
Transfer to Privacy
Works on AT&T, T-Mobile and Verizon:
Join Calls
You should be able to find steps for your vehicle here: http://owner.ford.com/how-tos.html
Note: Firefox Sync is different, it copies data between Firefox on your desktop and Firefox on your Android device and doesn't connect to your vehicle.

How to get ASF format to work with FCP

I have a Neuros 442 DVR that I’m trying to pull footage from and play in Final Cut Pro. The thing is that the format that the DVR records in is ASF and Final Cut Pro will not read that. I have put it in a Windows (yes I know I’m sorry) and it would read it but would not convert it without hesitations it the video. If anyone knows how to do this pleas let me know thanks.
Villi Olafsson

i did what you said and dowloaded that from flip4mac and it worked on letting the ASF files work with quicktime but the other thing that we are having a problum with is the glitching in the clips after convertion. (we need to conver to MOV from ASF and we are getting hesatations in the clips. which our clients will not like at all. if you now anything else that would help me out that would be great thanks
Villi O.

Compaq Presario R3000 how to get the sound to work with Windows 7 RC

1) Download SP29586.exe: ftp://ftp.hp.com/pub/softpaq/sp29501-30000/sp29586.exe
2) Run it, Create a directory c:\ swsetup
3) Once all the Files are extracted DO NOT INSTALL
4) Now Goto the Start Menu Click on Devices and Printers, the Click on the Name you have called your machine this will be marked will a yellow triangle as the sound driver windows 7 has install already is a realtek ac 97 which is not working,
5) Once your Machinename you will see a general tab and and hardware tab select the hardware tab.
6) Look for the Realtek ac 97 under the Device functions, select that and click properties,
7) Now tab to the Driver, now click update driver,
8) Select the option let me pick from a list of devices drivers, now click have disk
9) Click on Browse select the following location Swsetup\SP29586\SMAXWDM\W2K_XP and click on smwdmCH6.inf
10)Now the Soundmax Driver should come up select ok and next. Now your Sound will work
This question was solved.
View Solution.

I am basicaly having the same problem with my labtop. I tried the following above and yet I still have not been able to get my sound to work. I have had some problems with my power and sound cards before but after I reinstalled windows my graphics card and sound card have not been working to their full potential. I thaught that it was a 64 bit graphics card, but now I am not so sure. I had to jostle the power cord in the back till I mannaged to find a perfect spot to keep the computer running. Before the reinstallation I had to put pressure on the left side of the computer to get the sound to work.. but even then it still came in and out.. "The sound that is." I can see the same driver in the codex menue and it is yellow but, what you stated above did not work.
It says (Cannot continue the hardware update) The wizard cannot find a better match for your hardware than the software that you curently have installed. and then tells me to keep the current software. My sound Icon does not show up when I go to the settings.... I can't play diablo 2 on this no idea why... But my screen is choppy when I scroll through internet sites and it did not do that before. I have a 400mbs connection .... here is my computer information. :Compaq Presario R3000 Intel pent4 2.80ghz 2.80ghz 1.12GB ram and im running on windows xp2 professional.

How to get Network Printing to work with Brother!!

Similar Messages

Maybe you are looking for