How to get this type of Layout

Question

I got a typical requirement in scripts , such that the layout is similat to Excel Sheet...How to maintain that layout ?

Answer 1

hi manjunath,
Use the BOX, POSITION, and SIZE commands for drawing boxes, lines, and shading to print particular windows within a form or passages of text within a window in a frame or with shading.
The SAP printer drivers that are based on page-oriented printers (the HP LaserJet driver HPL2, the Postscript driver POST, the Kyocera Prescribe driver PRES) employ these commands when printing. Line printers and page-oriented printers not supported in the standard ignore these commands. You can view the resulting printer output in the SAPscript print preview.
Syntax:
8.     /: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]
9.     /: POSITION [XORIGIN] [YORIGIN] [WINDOW] [PAGE]
10.     /: SIZE [WIDTH] [HEIGHT] [WINDOW] [PAGE]
6.19.1     BOX Command
Syntax
/: BOX [XPOS] [YPOS] [WIDTH] [HEIGHT] [FRAME] [INTENSITY]
Effect: draws a box of the specified size at the specified position.
Parameters: For each of XPOS, YPOS, WIDTH, HEIGHT, and FRAME, you must specify both a measurement and a unit of measurement. Specify the INTENSITY parameter as a percentage between 0 and 100.
XPOS, YPOS
Upper left corner of the box, relative to the values of the POSITION command.
Default: Values specified in the POSITION command.
The following calculation is performed internally to determine the absolute output position of a box on the page:
X(abs) = XORIGIN + XPOS
Y(abs) = YORIGIN + YPOS
WIDTH
Width of the box. Default: WIDTH value of the SIZE command.
HEIGHT
Height of the box. Default: HEIGHT value of the SIZE command.
FRAME
Thickness of frame.
Default: 0 (no frame).
INTENSITY
Grayscale of box contents as %.
Default: 100 (full black)
Measurements: You must specify decimal numbers as literal values (like ABAP numeric constants) by enclosing them in inverted commas. Use the period as the decimal point character. See also the examples listed below.
Units of measurement: The following units of measurement may be used:
•     TW (twip)
•     PT (point)
•     IN (inch)
•     MM (millimeter)
•     CM (centimeter)
•     LN (line)
•     CH (character).
The following conversion factors apply:
•     1 TW = 1/20 PT
•     1 PT = 1/72 IN
•     1 IN = 2.54 CM
•     1 CM = 10 MM
•     1 CH = height of a character relative to the CPI specification in the form header
•     1 LN = height of a line relative to the LPI specification in the form header
/: BOX FRAME 10 TW
Draws a frame around the current window with a frame thickness of 10 TW (= 0.5 PT).
/: BOX INTENSITY 10
Fills the window background with shading having a gray scale of 10 %.
/: BOX HEIGHT 0 TW FRAME 10 TW
Draws a horizontal line across the complete top edge of the window.
/: BOX WIDTH 0 TW FRAME 10 TW
Draws a vertical line along the complete height of the left hand edge of the window.
/: BOX WIDTH '17.5' CM HEIGHT 1 CM FRAME 10 TW INTENSITY 15
/: BOX WIDTH '17.5' CM HEIGHT '13.5' CM FRAME 10 TW
/: BOX XPOS '10.0' CM WIDTH 0 TW HEIGHT '13.5' CM FRAME 10 TW
/: BOX XPOS '13.5' CM WIDTH 0 TW HEIGHT '13.5' CM FRAME 10 TW
Draws two rectangles and two lines to construct a table of three columns with a highlighted heading section.
reward point if information is need ful
thanks,
vaibhav