How to identify which server are connected in a switch?

Hi,
Many servers are connected to a switch?
How to identify what server are connected to which port remotely?
Thanks!
Samuel

Hi Sam,
just issue the command show ip arp , it will display some thing like this for know the MAC address & the VLAN number.
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.2.1.18 9 0800.6913.710e ARPA Vlan2
to know on which port it is connected, just issue the command as mentioned below
sh mac-address-table address 0800.6913.710e
Mac Address Table
Vlan Mac Address Type Ports
2 0800.6913.710e DYNAMIC Po1
hpe this will help you to identify your servers.
rate this post.

Similar Messages

How to identify Which ports are using in RAC setup?

Hi,
how to identify Which ports are using in RAC setup?
Thnaks,

[Viewing Port Numbers and Access URLS|http://download.oracle.com/docs/cd/B19306_01/install.102/b14205/ports.htm#sthref1208]

Which server is connected to a switch interface

Hi all,
We have a few switches in our company and we wanted to know an easy and quick way to find out which servers are connected to that switch (even if possible on which interface).
For example:
Firewall -> Switch1 interface Gig 0/1
Mail or 10.10.10.10 -> Switch2 interface Gig 0/3
I'm using at this moment the following command:
show cdp neighbors
It gives me all cisco device connected to that switch.
Is there an other command that does the same? Displaying the DNS or IP of a server that is connected to that interface of the switch.
Kind Regards

Hi,
a) there are some free tools available to track the end devices.
SolarWinds User Device Tracker might be an example (not tested personally).
b) If you want to run a CLI command, you usually need to take an opposite way: find out the device IP or MAC address and track to which switch port it's connected.
So you can list the FW ARP cache in your case.
And then to use "trace mac ip ..." switch CLI command, e.g.
See
http://www.cisco.com/en/US/customer/docs/switches/lan/catalyst3750/software/release/12.2_25_sec/command/reference/cli3.html#wp1917847
or
http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_25_sec/command/reference/cli3.pdf
for details.
HTH,
Milan

Deduplication: how to identify which files are "in-policy" (and which are not)?

Dear experts,
in eventlog I find the following information for one of my deduplicated volumes:
Volume: F: (\\?\Volume{9794e270-fb08-487e-979b-8a08fa9ca311}\)
Error code: 0x0
Error message:
Savings rate: 24
Saved space: 853327714684
Volume used space: 2681869406208
Volume free space: 66771247104
Optimized file count: 1199618
In-policy file count: 1188049
Job processed space (bytes): 0
Job elapsed time (seconds): 2
Job throughput (MB/second): 0
Some things look strange to me:
- The savings rate is only 24% which looks odd because I get about 40% on other file shares with similar characteristics.
- The "Optimized file count" is higher than the "in-policy" file count.
- The volume has about 3.5 million files but only 1.1 million files are "in-policy".
My understanding of "in-policy" files is that all files are in-policy which are older than 3 days (if not configured different, which is not the case) and which are not contained in an excluded folder (nothing configured here) and which have no
excluded file extension (nothing configured here apart from the default). Right?
I'm sure that only a small fraction of the files on this volume are younger than three days, so something seems to be wrong there, but I have no idea how to find the cause of the problem.
Is there any way to identify the files (full path) which are considered to be not "in-policy"?
How can I find out if the optimization process really looks at all files - and doesn't skip a million?
Thanks!
Regards
Christoph

Mandy, thanks for your feedback! I've read these technet articels, but I couldn't learn something really helpfull related to my problem there. To make investigation of the problem easier I did the following:
- created a brand new empty volume (x:) on the same server
- enabled data deduplication on that volume with a minimal file age of 0 days
- copied about 2GB of data from the problem-volume in 15450 files to this new volume
- started "Start-DedupJob x: -Type Optimization -Memory 50"
After a few seconds that job completed and I got the following result:
Volume: X: (\\?\Volume{d1ba9ed8-28f1-44d1-9535-fe603d6a70c6}\)
Error code: 0x0
Error message:
Savings rate: 0
Saved space: 12360718
Volume used space: 3091664896
Volume free space: 7610097664
Optimized file count: 153
In-policy file count: 153
Job processed space (bytes): 46095214
Job elapsed time (seconds): 9
Job throughput (MB/second): 4.88
The question is: why are only 153 files in-policy?
All files (of more than 15000) are of course "older than 0 days", there are no excluded folders configured, there are no excluded extensions configured, no file has one of the default excluded extensions and more than 1000 files are bigger than 100kB
(minimal size for deduplication is 32kB). So what makes only 153 files qualify for deduplication?
My impression is that there are further undocumented requirements which have to be met by a file to qualify for deduplication. But if there's no detailed log of an optimization run available how to find out what's going on?
(Or is something going wrong on my server?)
Kind Regards
Christoph

How to identify which albums are missing from my iTunes

I recently got a new PC with loads of storage so I have been copying mp3's onto it from various old backups and CD's that wouldn't fit on my old laptop.
Is there an automated way of importing the albums that don't already exist in the iTunes library? It would be a mess to import everything then weed out the dupes!

You can put everything into the "Automatically add to iTunes" folder, but there are occasional horror stories about those files going missing. You can also add the entire media folder, but occasionally that can create duplicate entries in the library, particularly if you have split the media folder to a separate location on a drive that isn't permanently connected to your computer.
tt2

How to know which interfaces are going to which switch?

How to know which interfaces are going to which switch ?
I know that cdp will show this information. But CDP will not show info about the devices connected to my device and whose link between is administratively down.
Regards,
Chandu

I don't want to the end devices location.
For example, i have a switch that connect to multiple switches few using etherchannels and few using stand-along ports.
So assume that one of the link whether it may be entire port-channel or a stand alone link that connects to another switch has been shut down manually by some x person...
Then how can i know that which interfaces are connecting to that switch. In this case i think CDP will not help because it will hold the information of ports that are up.
Regards,
Chandu

How to identify which videos

I took a dozen or so short clips of an event. I know which three I want to combine and edit. But I can't figure out how to identify which they are in imovie in order to put those clips in my project. It shows them all as consecutive clips or frames, without file numbers or names.

I'll try to explain better.
A dozen clips or videos, 1 min to 5 min in length. In one case all along a mountain road.
I want to produce a 5 min project or video with the best parts of 3 of those 12.
All 12 have thumbnails almost identical (the dashboard across the bottom, roof line at the top)
I only want to start editing the 3, not put all 12 in.
How do I identify those 3?

How can I know which clients are connected to my network through express and which are connected through extreme?

I have an airport express extending, through wireless, a network provided by an airport extreme. How can I know which clients are connected to my network through express and which are connected through extreme?
Here you can see both routers:
I would expect to some clients connected to the express, other than the extreme. And that's all I see: only the airport extreme appears as client of the airport express.
Below, one can see the summary of the config for both routers.
Would somebody explain it?
Thanks,
Marcelo
Message was edited by: Marcelão

please disregard this answer.
Message was edited by: Marcelão

How can i see which devices are connected to my wireless network?

how can i see which devices are connected to my wireless network?

Login to your router and view the DHCP clients.

How to identify which is rootsite/webapplication url and which are site collection url ?

How to identify which is rootsite/webapplication url and which are site collection url underneath of web application using powershell script in following code?
# Get site objects
$webapplication = Get-SPWebApplication $siteUrl
# Walk through each site in the site collection
foreach($site in $webapplication.Sites)
foreach($subWeb in $site.AllWebs)
$_ = AddLevel123($subWeb.Url)

Hi,
Hope you wanted to know which API is Site collection (SPSite) and Sub site(SPWeb)
$webapplication.Sites = Site Collection (SPSite)
and $site.AllWebs = Subsite (SPWeb)
and see these links - to get webApplication URL
http://social.msdn.microsoft.com/Forums/sharepoint/en-US/e223b607-ab35-454a-a050-1db3005687e5/spwebapplication-url?forum=sharepointdevelopmentlegacy
SPSite Url - SPSite.Url (http://msdn.microsoft.com/en-us/library/office/microsoft.sharepoint.spsite.url.aspx)
SPweb URl - SPWeb.URL (http://msdn.microsoft.com/en-us/library/office/microsoft.sharepoint.spweb.url.aspx)
http://social.technet.microsoft.com/Forums/sharepoint/en-US/b4dfb645-69f4-4abd-947c-64ca42af3a26/script-to-get-list-of-sites-and-subsites
Hope this helps!
MCITP: SharePoint 2010 Administrator
MCTS - MOSS 2007 Configuring, .NET 2.0
| SharePoint Architect | Evangelist |
http://www.sharepointdeveloper.in/
http://ramakrishnaraja.blogspot.com/

How to identify Which function modules are used in the planning area?

Hi all,
there are couple of function module derviation is used to derive the calendar year, month, fiscal period etc.
But how to identify which function module is used in which planning area?
I cant find out from the where used list from function modules?
Thanks
pooja

Hi Pooja,
Go to characteristic relationship tab,click on detail icon on extreme left of the derivation,there you will get the name and the details of function module used for derivation.
Regards,
Indu

How do i identify what devices are connected to 101, 102, etc on my air port extreme?

How do i identify what devices are connected to 101, 102, etc on my air port extreme?

Depending on whether a device is connecting using Ethernet or wireless, you need to know the Ethernet ID or AirPort ID of the device. That is the number that is associated with the IP address that is displayed in AirPort Utility.
For example, if you have a Mac....
Open System Preferences (gear icon on the dock) and open Network
Click on AirPort , then click Advanced at the lower right
The AirPort ID of the Mac is displayed at the bottom of the window
For the Ethernet ID, click on Ethernet, then click Advanced, then click the Ethernet tab
The Ethernet ID is displayed at the top of the window
On an iPhone.....
Tap the Settings icon, tap General, tap About, then scan down to locate Wi-Fi Address, also known as the AirPort ID.

TS2972 how can i identify which computers are authorized for i tunes

How can I identify which computers are authorized for use with I tunes?

Hi there,
You can't see a list of your authorised computers, but you can see how many are authorised and deauthorise them individually or together.
I've found you a relevent support article which explains all of this:
iTunes Store: About authorization and deauthorization
Hope this helps,
Nathan

How to identify which root certificate is used?

How to identify which root certificate(on terminal) is used when a terminal is connecting to a https website?
SecurityInfo.getServerCertificate() only returns the certificate send from the https server.
But how could know the which local root certificate is used to verify the certificate send from the https server?
Is there a method or class in MIDP 2.1?
Thanks

UP�Cthis question is urgent. Hope anyone can answer me!

How ABAP and JAVA stacks are connecting

Hi Experts,
I have a doubt in pi. We are developing Message Mapping in IR, it means it is running on JAVA STACK. But we are checking any mapping error in SXMB_MONI which will run on ABAP STACK.
Now My doubt is " How JAVA and ABAP stacks are connecting to each other and How we are able to see Mapping error in Integration Engine which resides on ABAP stack even though we create Mapping in IR which runs on Java".
Thanks&Regards ,
Gajapathi.

Hi Gajapathi,
How JAVA and ABAP stacks are connecting to each other
PI manages using single database for both JAVA and ABAP servers. But both access them using different schema. They connect using RFC protocol via SAP Java Connector (JCo Connector).
How we are able to see Mapping error in Integration Engine
which resides on ABAP stack even though we create Mapping in IR which runs on Java".
So when you create a object be it mapping or interface or any XI objects, it is stored in Single Database. When you use ABAP sxmb_moni for monitoring the message, it uses ABAP related schema to access the message.
I hope it answers you query.
Regards
Ramesh

How to identify which server are connected in a switch?

Similar Messages

Maybe you are looking for