How to improve sampling rates in mega samples spartan 3e board
I am trying to acquire data in spartan 3e board in mega samples rate can you post me any examples for this purpose
Solved!
Go to Solution.
If you're trying to get analog samples in that range, the issue that you're going to run into is that that sort of sampling rate is right at the bleeding edge of what you're asking for (it's a 2-channel @ 1.5Msps chip, the LTC1407A-1). If you actually want to capture at these rates, you're going to need to pull some interesting LV-foo using single-cycle timed loops in the FPGA diagram or drop some code down into an IPNode/CLIP Node, with outputs from those IP blocks hooked to the IO in a SCTL.
Please let us know a bit more about your specific design.
-Brad
Similar Messages
-
How to output sample and convert clocks to PFI lines of E-Series DAQ (DAQPad-6015)
Hi,
Can someone tell me how to output sample and convert clocks to PFI lines of E-Series DAQ (DAQPad-6015)?
Thank you very much.
JackJohn --
Windows is not an option for me. I like your idea of using a counter output -- it may be helpful as I am getting ramped up, but my application will eventually require both timer outputs.
I have a legacy C application written for Macintosh, and I am in the process of moving it onto OS X. So my options are to use DAQmx Base, or write an in-kernel driver. I actually have already done the latter for 6024/6025 E-series boards (for another company); for this client I was hoping to use the DAQmx Base to allow an easy transition to M-series boards, without the cost of writing and supporting a low-level driver.
The specific task I am doing is relatively straightforward. I record 2 channels of AI for a short period (usually about 250 ms.) and during this time I drive 2 external digital signals. Right now, I use the 2 timer outputs, which allows precise synchronization with the output and AI sampling.
I appreciate your comments, and thanks in advance for any additional suggestions you can lob my way.
--spg
Scott Gillespie
Applied Brain, Inc.
scott gillespie
applied brain, inc. -
How to assign sampling procedure at plant level.
Hi Team,
Pls suggest me "How to assign sampling procedure at plant level."
Error message is - You can not use sampling procedure here.
Not all sampling procedures can be used in this context.
Example:
Only the sampling procedures for an attributive inspection based on the
number of nonconforming units are allowed.
However I have assigned 0.05% sampling procedure in IDES system plant, which is accepted. However I am not allowed to assign this in client system..
Pls suggest me solution.
ThanksHi,
During creation of inspection plan you can assign SP at plant level, IP always at plant level
Q.Error message is - You can not use sampling procedure here.
---> pl check the MIC where Sampling procedure in clicked or not
pl revert
Cheers, -
Hi
We deleted sample basic after we installed Essbase (11.1.1.3). Now some users want to have sample basic available to practice. Do anyone know how to recreate sample basic in Essbase?
Thanksopening the zip file it looks like all of the files are there. So from EAS create the Sample application (BSO non unicode) and then create the database Basic. Stop the application then copy all of the files in the zip into the basic directory on the server (pathing may vary based on what version you are using) but there should be an app\sample\basic directory. Then start the app and you should be good to go
-
How can I improve the rate of success in Siri recognizing what I am saying (rate of success nil, to date)?
justjesper wrote:
Excelent question.
I have been searching around, and it looks like a lot of users is asking this question.
Where can I make Siri learn my accent ? Some users was talking about a feature where you could correct Siri so it would learn, but I have not been able to find it.
Nor have I, but it does seem to get better as I go along, so maybe it learns. -
HT1338 system preference not open so how guide to sample?
My mac book pro in system preference not open so how guide to sample?
Hello,
First, Safe Boot , (holding Shift key down at bootup), use Disk Utility from there to Repair Permissions, test if things work OK in Safe Mode.
Then move these files to the Desktop for now...
/Users/YourUserName/Library/Preferences/com.apple.finder.plist
/Users/YourUserName/Library/Preferences/com.apple.systempreferences.plist
/Users/YourUserName/Library/Preferences/com.apple.desktop.plist
/Users/YourUserName/Library/Preferences/com.apple.recentitems.plist
Reboot & test.
PS. Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive. -
hi,'
sap gurus,
good morning to all,
how to treat sample sales in R/3
which document type supports that.
what is the impact happens when goods send thru samples in sap
regards,
balaji.t
09990019711.Dear Balaji,
There is no seperate document type for the sample process in SAP R/3.
We can copy standard document type OR then we can rename ot according to ours.
One more importent point is pricing to the samples.
We need to define the seperate pricing procedure to the samples as per the requirement and we need to determine that according to the Customer , Document pricing group and sales area.
Noramally for sample only tax will be charged so we need to define pricing procedure in suchway.
I hope it will clear for you,
Regards,
Murali. -
How to improve speed of data acquisition? Help needed urgently.
I want to convert analog signals to digital signals and simultaneously perform some search on the data acquired and this whole process has to be done continuously for few hours.
So I tried writing two programs in Matlab, one acquires the analog data and converts it to digital and saves the data in small chunks on hard disk (like file1, file2, file3,...) continuously. The other program performs the search operation in those chunks of data continuously. I run both the programs at a time by opening two mat lab windows.
But the problem Iam facing is that the data acquisition is slow. As a result I get an error message in the second program saying that
"??? Error using ==> load
Unable to read file file4.mat: No such file or directory."
Iam unable to synchronize the two programs. I cannot use timers in search program because I cannot add any delays.
Iam using a NI PCI-6036E ,16 Bit Resolution ,200 KS/s Sampling Rate A/D board.
Should I switch to some other series such as M series having sampling rate of the order MS/s?
Can anyone please tell me how to improve the speed of data acquisition?
Thanks.Gayathri wrote:
I want to convert analog signals to digital signals and simultaneously perform some search on the data acquired and this whole process has to be done continuously for few hours.
So I tried writing two programs in Matlab, one acquires the analog data and converts it to digital and saves the data in small chunks on hard disk (like file1, file2, file3,...) continuously. The other program performs the search operation in those chunks of data continuously. I run both the programs at a time by opening two mat lab windows.
But the problem Iam facing is that the data acquisition is slow. As a result I get an error message in the second program saying that
"??? Error using ==> load
Unable to read file file4.mat: No such file or directory."
Iam unable to synchronize the two programs. I cannot use timers in search program because I cannot add any delays.
Iam using a NI PCI-6036E ,16 Bit Resolution ,200 KS/s Sampling Rate A/D board.
Should I switch to some other series such as M series having sampling rate of the order MS/s?
Can anyone please tell me how to improve the speed of data acquisition?
Thanks.
Hi gayathri,
well my email is [email protected]
if ur from india mail me back.
Regards
labview boy -
How to improve this query speed ?....help me
How to improve the query speed. Any hints can u suggest in the query or any correction. Here i am using sample tables for checking purpose, When i am trying with my original values, this type of query taking longer time to run
select ename,sal,comm from emp where(comm is null and &status='ok') or (comm is not null and &status='failed');
Thanx in advance
prasanth a.s.What about
select ename,sal,comm from emp where comm is null and &status='ok'
union all
select ename,sal,comm from emp where comm is not null and &status='failed';
Regards
Vaishnavi -
Hi very urgent How to improve the performence of the program
Hi all please tell me how to improve the performence of this program......
REPORT z03_gil010 NO STANDARD PAGE HEADING LINE-SIZE 130.
INCLUDE *
INCLUDE: z00_bci010. " Gestion des anomalies.
Déclaration des données *
Tables de la bases de données *
TABLES:
ekpo, " Poste document d'achat.
lfa1, " Base fournisseurs (généralités).
marc, " Données division de l'article.
z03_bw_cmp1,
eord, "Répertoire des sources appro. Achats
eina, "Fiche infos-achats - données générales
t024, "Groupes d'acheteurs
tvarv. "FAE17345+
Déclaration des données internes *
Déclaration de la table interne qui permet de recuperer les mois.
DATA: BEGIN OF itb_months OCCURS 12.
INCLUDE STRUCTURE t247.
DATA: END OF itb_months.
Table pour récupération d'infos sur les divisions
DATA: BEGIN OF itb_t001w OCCURS 0,
werks LIKE t001w-werks,
fabkl LIKE t001w-fabkl," Clé du calendrier d'entreprise
END OF itb_t001w.
Déclaration de la table interne contenant les infos sur l'adresse du
fournisseur.
DATA: BEGIN OF itb_adresse OCCURS 0,
lifnr LIKE lfa1-lifnr, " Numéro de compte fournisseur.
name1 LIKE lfa1-name1, " Nom 1.
name2 LIKE lfa1-name2, " Nom 2.
name3 LIKE lfa1-name3, " Nom 3.
name4 LIKE lfa1-name4, " Nom 4.
stras LIKE lfa1-stras, " N° de rue et nom de la rue.
pstlz LIKE lfa1-pstlz, " Code postal.
ort01 LIKE lfa1-ort01, " Localité.
pfach LIKE lfa1-pfach, " Boîte postale.
pstl2 LIKE lfa1-pstl2, " Code de la boîte postale.
land1 LIKE lfa1-land1, " Clé de pays.
landx LIKE t005t-landx, " Pays.
spras LIKE lfa1-spras, " Code langue
END OF itb_adresse.
Déclaration d'une table interne pour les informations sur les
prévisions de commande.
DATA: BEGIN OF itb_prev_cde OCCURS 0,
werks LIKE marc-werks, " Division
idnlf LIKE eina-idnlf, " ADDsde ref article frn
lifnr LIKE eord-lifnr, " N° fournisseur.
ekgrp LIKE marc-ekgrp, " Groupe d'acheteurs
dispo LIKE marc-dispo, " Code gestionnaire MRP
matnr LIKE eord-matnr, " Article.
maktx LIKE makt-maktx, " Désignation article.
bstmi LIKE marc-bstmi, " Quantité de commande.
men00 LIKE plaf-gsmng, " Quantité du mois en cours M.
men01 LIKE plaf-gsmng, " Quantité pour le mois M+1.
men02 LIKE plaf-gsmng, " Quantité pour le mois M+2.
men03 LIKE plaf-gsmng, " Quantité pour le mois M+3.
men04 LIKE plaf-gsmng, " Quantité pour le mois M+4.
men05 LIKE plaf-gsmng, " Quantité pour le mois M+5.
men06 LIKE plaf-gsmng. " Quantité pour le mois M+6.
DATA: END OF itb_prev_cde.
Structure de travail pour les commandes convernant les PFC
DATA str_pca_pfc LIKE itb_prev_cde.
*add sde
DATA str_eord_pfc LIKE itb_prev_cde.
Structure de travail pour les prévisons PFC
DATA str_prev_pfc LIKE itb_prev_cde.
Déclaration d'une table interne pour les informations sur le
portefeuille des commandes d'achat.
DATA: BEGIN OF itb_pca OCCURS 0,
werks LIKE ekpo-werks, " Division
idnlf LIKE eina-idnlf, " ADDsde ref article frn
lifnr LIKE eord-lifnr, " N° fournisseur.
ekgrp LIKE marc-ekgrp, " Groupe d'acheteurs
dispo LIKE marc-dispo, " Code gestionnaire MRP
matnr LIKE eord-matnr, " Article.
maktx LIKE makt-maktx, " Désignation article.
ebeln LIKE ekes-ebeln, " Numéro du document d'achat.
ebelp LIKE ekes-ebelp, " Numéro de poste du document d'achat.
slfdt LIKE eket-slfdt, " Date de livraison statistique
eindt LIKE ekes-eindt, " Date de livraison indiquée dans la
" confirmation de la cde.
menge LIKE ekes-menge, " Quantité indiquée dans la confirma-
" tion de la commande.
attdu LIKE eket-wemng, " Portefeuille fournisseur.
netpr LIKE ekpo-brtwr, " Prix net du document d'achat dans
" la devise du document.
rtard TYPE i, " Retard en jours ouvres.
wemng LIKE eket-wemng, " Quantité de l'entrée de marchandise.
bldat LIKE mkpf-bldat, " Date inscrite sur la pièce/sur le
" document.
qtran LIKE ekes-menge, " Quantité en transit.
dtran LIKE ekes-eindt. " Date du dernier avis de transit.
DATA: END OF itb_pca.
DATA: w_i TYPE i, "Compteur
w_i_char(1) TYPE c, "Texte pour récupérer compteur
w_nm_zone(20) TYPE c, "Nom zone pour assign au field-symbols
w_nb_j TYPE i, "Nb de jours ouvrés jusqu'à fin mois
w_nb_j_tot TYPE i. "Nb de jours ouvrés du mois
FIELD-SYMBOLS: TYPE ANY.
Déclaration d'une table contenant les fiches info achat.
DATA: BEGIN OF itb_eina OCCURS 0,
matnr LIKE eina-matnr,
lifnr LIKE eina-lifnr,
idfnl LIKE eina-idnlf.
DATA: END OF itb_eina.
Déclaration d'une table contenant les infos groupe acheteur.
*DATA: BEGIN OF itb_t024 OCCURS 0,
ekgrp LIKE t024-ekgrp,
eknam LIKE t024-eknam,
ektel LIKE t024-ektel,
telfx LIKE t024-telfx.
*DATA: END OF itb_t024.
Déclaration d'une table pour le transfert du fichier.
DATA: BEGIN OF itb_transfert OCCURS 0,
col00(8), "division
col00bis(20), "Reference article
col01(18), "No article
col02(45), "libelle article
col021(17), "Groupe acheteur
col022(13), "gestionnaire
col03(17), "qte commandée ou No de commande
col04(13), "Mois 1 ou No poste cde
col05(20), "Mois 2 ou délai initial
col06(33), "Mois 3 ou délai négocié
col07(13), "Mois 4 ou qté cdée
col08(13), "Mois 5 ou qté attendue
col09(13), "Mois 6 ou Montant attendu
col10(13), "Mois 7 ou retard
col11(13), "qte partielle livree
col12(13), "date livraison partielle
col13(13), "qté en transit
col14(13). "date
DATA: END OF itb_transfert.
Déclaration d'une table contenant la liste des fournisseurs.
DATA: BEGIN OF itb_lifnr OCCURS 0,
werks LIKE marc-werks,
idfnl LIKE eina-idnlf,
lifnr LIKE eord-lifnr,
ekgrp LIKE marc-ekgrp,
spras LIKE lfa1-spras,
eknam LIKE t024-eknam,
ektel LIKE t024-ektel,
telfx LIKE t024-telfx.
DATA: END OF itb_lifnr.
Déclaration d'une structure pour la selection dans la table MSEG.
DATA : BEGIN OF itb_mseg OCCURS 0,
mblnr LIKE mseg-mblnr,
mjahr LIKE mseg-mjahr,
ebeln LIKE mseg-ebeln,
ebelp LIKE mseg-ebelp,
END OF itb_mseg.
déclaration d'une structure pour la selection dans EKPO.
DATA : BEGIN OF itb_ekpo OCCURS 0,
lifnr LIKE ekko-lifnr,
ebeln LIKE ekpo-ebeln,
ebelp LIKE ekpo-ebelp,
menge LIKE ekpo-menge,
bpumz LIKE ekpo-bpumz,
bpumn LIKE ekpo-bpumn,
matnr LIKE ekpo-matnr,
werks LIKE ekpo-werks,
netpr LIKE ekpo-netpr,
peinh LIKE ekpo-peinh, "Base de prix FAE17345+
ekgrp LIKE ekko-ekgrp, "AFT++
dispo LIKE marc-dispo, "AFT++
END OF itb_ekpo.
déclaration d'une structure pour la selection dans EKPO.
DATA : BEGIN OF itb_ekko OCCURS 0,
ebeln LIKE ekko-ebeln,
lifnr LIKE ekko-lifnr,
spras LIKE ekko-spras,
END OF itb_ekko.
déclaration d'une structure pour la selection dans EKES.
DATA : BEGIN OF itb_ekes OCCURS 0,
ebeln LIKE eket-ebeln,
ebelp LIKE eket-ebelp,
ebtyp LIKE ekes-ebtyp,
eindt LIKE ekes-eindt,
menge LIKE ekes-menge,
dabmg LIKE ekes-dabmg,
etens LIKE ekes-etens,
END OF itb_ekes.
déclaration d'une structure pour la selection dans EKET
DATA : BEGIN OF itb_eket OCCURS 0,
ebeln LIKE eket-ebeln,
ebelp LIKE eket-ebelp,
menge LIKE eket-menge,
wemng LIKE eket-wemng,
eindt LIKE eket-eindt,
slfdt LIKE eket-slfdt,
END OF itb_eket.
déclaration d'une structure pour la selection dans MKPF.
DATA : BEGIN OF itb_mkpf OCCURS 0,
mblnr LIKE mkpf-mblnr,
mjahr LIKE mkpf-mjahr,
bldat LIKE mkpf-bldat,
END OF itb_mkpf.
Déclaration d'une structure pour la sélection dans EORD.
DATA : BEGIN OF itb_eord OCCURS 0,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
lifnr LIKE eord-lifnr,
ekgrp LIKE marc-ekgrp,
dispo LIKE marc-dispo, "DE3K924352
disls LIKE marc-disls,
bstfe LIKE marc-bstfe,
bstrf LIKE marc-bstrf,
bstmi LIKE marc-bstmi,
bstma LIKE marc-bstma,
END OF itb_eord.
DATA : BEGIN OF itb_eordw OCCURS 0.
INCLUDE STRUCTURE itb_eord.
DATA : END OF itb_eordw.
Déclaration d'une structure pour la sélection dans MAKT.
DATA : BEGIN OF itb_makt OCCURS 0,
matnr LIKE makt-matnr,
spras LIKE makt-spras,
maktx LIKE makt-maktx,
END OF itb_makt.
Déclaration d'une structure pour la sélection dans EBAN.
DATA : BEGIN OF itb_eban OCCURS 0,
matnr LIKE eban-matnr,
werks LIKE eban-werks,
flief LIKE eban-flief,
lfdat LIKE eban-lfdat,
menge LIKE eban-menge,
bsmng LIKE eban-bsmng,
webaz LIKE eban-webaz,
ekgrp LIKE eban-ekgrp,
ebeln LIKE eban-ebeln,
banfn LIKE eban-banfn,
bnfpo LIKE eban-bnfpo, "DB3K900702+
END OF itb_eban.
Déclaration d'une structure pour la sélection dans PLAF.
DATA : BEGIN OF itb_plaf OCCURS 0,
plnum LIKE plaf-plnum, "DB3K900702+
matnr LIKE plaf-matnr,
plwrk LIKE plaf-plwrk,
flief LIKE plaf-flief,
pedtr LIKE plaf-pedtr,
gsmng LIKE plaf-gsmng,
webaz LIKE plaf-webaz,
END OF itb_plaf.
Déclaration d'une structure pour la sélection dans MARC.
DATA : BEGIN OF itb_marc OCCURS 0,
matnr LIKE marc-matnr,
werks LIKE marc-werks,
disls LIKE marc-disls,
bstrf LIKE marc-bstrf,
bstmi LIKE marc-bstmi,
bstma LIKE marc-bstma,
bstfe LIKE marc-bstfe,
ekgrp LIKE marc-ekgrp,
dispo LIKE marc-dispo,
END OF itb_marc.
DATA : BEGIN OF itb_marc_eord OCCURS 0,
matnr LIKE marc-matnr,
werks LIKE marc-werks,
strgr LIKE marc-strgr, "groupe de stratégie planif
END OF itb_marc_eord.
DATA : BEGIN OF itb_z03_bw_cmp1 OCCURS 0,
matnr LIKE z03_bw_cmp1-matnr,
werks LIKE z03_bw_cmp1-werks,
pdatu LIKE z03_bw_cmp1-pdatu,
plnmg LIKE z03_bw_cmp1-plnmg,
END OF itb_z03_bw_cmp1.
Begin change BNI <DE3K937051>
DATA : BEGIN OF itb_z03_bw_cmp2 OCCURS 0,
matnr LIKE z03_bw_cmp2-matnr,
werks LIKE z03_bw_cmp2-werks,
pdatu LIKE z03_bw_cmp2-pdatu,
plnmg LIKE z03_bw_cmp2-plnmg,
END OF itb_z03_bw_cmp2.
*End change BNI
DATA : BEGIN OF str_index1,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index1.
DATA : BEGIN OF str_index2,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index2.
DATA : BEGIN OF str_index3_eord,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index3_eord.
DATA : BEGIN OF str_index4,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index4.
DATA : BEGIN OF str_index5,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index5.
DATA : BEGIN OF str_index6,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index6.
DATA : BEGIN OF str_index7,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index7.
Déclaration des variables de debut et de fin de mois.
DATA: w_debut_mois LIKE sy-datum,
w_debut_periode LIKE sy-datum,
w_fin_mois LIKE sy-datum,
w_fin_periode LIKE sy-datum.
Déclaration des variables pour les dates.
DATA: w_date0 LIKE sy-datum,
w_date1 LIKE sy-datum,
w_date2 LIKE sy-datum,
w_date3 LIKE sy-datum,
w_date4 LIKE sy-datum,
w_date5 LIKE sy-datum,
w_date6 LIKE sy-datum,
w_datejour LIKE sy-datum, "FAE15269
w_dat_da LIKE eban-lfdat,
w_dat_op LIKE plaf-pedtr,
w_mois0 LIKE t247-ltx,
w_mois1 LIKE t247-ltx,
w_mois2 LIKE t247-ltx,
w_mois3 LIKE t247-ltx,
w_mois4 LIKE t247-ltx,
w_mois5 LIKE t247-ltx,
w_mois6 LIKE t247-ltx,
w_lendemain LIKE sy-datum. "FAE17345+
Temoin d'un AR dans la commande d'achat.
DATA: w_temoin_ar.
Numéro de la confirmation de la commande
DATA : w_etens LIKE ekes-etens.
Déclaration des variables pour le nom des fichiers.
DATA: w_nom_fichier LIKE rlgrap-filename,
w_fichier LIKE rlgrap-filename,
w_racine LIKE rlgrap-filename,
w_file LIKE rlgrap-filename.
Déclaration d'une table interne pour le transfert.
DATA: BEGIN OF itb_trans OCCURS 0,
w_ligne(320).
DATA: END OF itb_trans.
Déclaration d'une variable pour rechercher les enregistrements vides.
DATA: w_compteur TYPE i,
w_compteur1 TYPE i,
w_compteur2 TYPE i,
w_retard TYPE i, " Retard en jours ouvres.
w_trouve_pfc TYPE c, "addsde
w_trouve_pfs TYPE c, "+DE3K937051
w_trouve TYPE c.
*Index pour les LOOP
DATA : w_index_ekpo LIKE sy-tabix,
w_index_ekes LIKE sy-tabix,
w_index_eket LIKE sy-tabix,
w_index_mseg LIKE sy-tabix,
w_index_eban LIKE sy-tabix,
w_index_plaf LIKE sy-tabix,
w_index_pca LIKE sy-tabix,
w_index_z03_bw_cmp1 LIKE sy-tabix,
w_index_z03_bw_cmp2 LIKE sy-tabix."+DE3K937051
RANGES : r_type_pfs FOR marc-strgr.
*fichier sur serveur +EDR231003
DATA : w_chemin LIKE filename-fileintern, "nom du fichier
w_date_fichier(12) TYPE c, "Date format DD_MM_AA
w_csv(307) TYPE c. "ligne du fichier format CSV
CONSTANTS: k_imputation_m LIKE eban-knttp VALUE 'M'. "FAE19001+
Description de l écran de sélection *
Paramètres "UTILISATION" *
Ouverture d'un block de sélection pour le(s) fournisseur(s).
SELECTION-SCREEN BEGIN OF BLOCK block1 WITH FRAME TITLE text-bl1.
Sélection division(s)
SELECT-OPTIONS: s_werks FOR ekpo-werks.
Sélection fournisseur(s).
SELECT-OPTIONS: s_lifnr FOR lfa1-lifnr OBLIGATORY.
Sélection du Groupe d'acheteur
*SELECT-OPTIONS: s_ekgrp FOR marc-ekgrp. "-FAE26446
*SELECT-OPTIONS: s_dispo FOR marc-dispo. "-FAE26446
SELECTION-SCREEN END OF BLOCK block1.
FAE 26446 : ajout
SELECTION-SCREEN BEGIN OF BLOCK block3 WITH FRAME TITLE text-bl3.
SELECTION-SCREEN BEGIN OF LINE.
PARAMETER p_ekgrp RADIOBUTTON GROUP g3.
SELECTION-SCREEN COMMENT 5(24) text-001 FOR FIELD p_ekgrp.
SELECT-OPTIONS: s_ekgrp FOR marc-ekgrp.
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
PARAMETER p_dispo RADIOBUTTON GROUP g3.
SELECTION-SCREEN COMMENT 5(24) text-002 FOR FIELD p_dispo.
SELECT-OPTIONS: s_dispo FOR marc-dispo.
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN END OF BLOCK block3.
FAE 26446 : fin ajout
Paramètres "SYSTEME" *
Saut de 2 lignes.
SELECTION-SCREEN: SKIP 2.
Ouverture d'un block de sélection pour l'adresse physique du fichier.
SELECTION-SCREEN BEGIN OF BLOCK block2 WITH FRAME TITLE text-bl2.
PARAMETERS: p_pc RADIOBUTTON GROUP rad1 DEFAULT 'X', "+EDR231003
p_fic_pc LIKE rlgrap-filename. "+EDR231003
SELECTION-SCREEN SKIP. "+EDR231003
PARAMETERS : p_serve RADIOBUTTON GROUP rad1, "+EDR231003
p_fic_se LIKE filename-fileintern "+EDR231003
DEFAULT 'Z03_PREV_COMMANDES'. "+EDR231003
SELECTION-SCREEN END OF BLOCK block2.
Logique de traitement *
INITIALIZATION *
INITIALIZATION.
Date du jour
MOVE sy-datum TO w_datejour. "FAE15269
Gestion des anomalies.
MOVE text-lb1 TO w_lb_traitement.
PERFORM f930_init USING sy-cprog '30'.
Fin de la gestions des anomalies.
Récuperation des mois dans la table interne 'ITB_MONTHS'.
CALL FUNCTION 'MONTH_NAMES_GET'
EXPORTING
language = sy-langu
TABLES
month_names = itb_months
EXCEPTIONS
month_names_not_found = 1
OTHERS = 2.
IF sy-subrc <> 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
Récupération des differentes periodes.
PERFORM f100_recuperation_date TABLES itb_months.
Récupération du debut du mois.
CONCATENATE sy-datlo(6) '01' INTO w_debut_mois.
MOVE: w_debut_mois TO w_debut_periode.
Récupération du dernier jour du mois.
CALL FUNCTION 'LAST_DAY_OF_MONTHS'
EXPORTING
day_in = sy-datlo
IMPORTING
last_day_of_month = w_fin_mois
EXCEPTIONS
day_in_no_date = 1
OTHERS = 2.
IF sy-subrc <> 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
TOP-OF-PAGE *
TOP-OF-PAGE.
CALL FUNCTION 'Z_00_BC_TOP_OF_PAGE'
EXPORTING
p_linsz = k_ligne
p_pagno = sy-pagno
p_prog = sy-cprog
p_projet = k_projet
p_societe = k_societe
p_sujet = sy-title.
END-OF-PAGE *
END-OF-PAGE.
AT SELECTION-SCREEN *
FAE 26446 : ajout
AT SELECTION-SCREEN ON BLOCK block3.
IF NOT ( s_ekgrp IS INITIAL )
AND NOT ( s_dispo IS INITIAL ).
MESSAGE e394(z03_mm).
ENDIF.
IF p_ekgrp = 'X'.
IF s_ekgrp IS INITIAL.
MESSAGE e395(z03_mm).
ENDIF.
ELSE.
IF s_dispo IS INITIAL.
MESSAGE e396(z03_mm).
ENDIF.
ENDIF.
fae26446 fin ajout
AT SELECTION-SCREEN ON BLOCK block2.
IF p_pc = 'X'.
IF p_fic_pc IS INITIAL.
*Attention, il n'y a aucune adresse de sauvegarde pour le(s) fichier(s)
MESSAGE e021(z03_mm).
ENDIF.
ELSE.
IF p_fic_se IS INITIAL.
*Attention, il n'y a aucune adresse de sauvegarde pour le(s) fichier(s)
MESSAGE e021(z03_mm).
ENDIF.
ENDIF.
Création du matchcode pour la selection du fichier local.
AT SELECTION-SCREEN ON VALUE-REQUEST FOR p_fic_pc.
CALL FUNCTION 'WS_FILENAME_GET'
EXPORTING
def_filename = p_fic_pc
def_path = 'C:'
mask = text-ma1
mode = 'S'
title = text-sel
IMPORTING
filename = p_fic_pc
EXCEPTIONS
inv_winsys = 1
no_batch = 2
selection_cancel = 3
selection_error = 4
OTHERS = 5.
IF sy-subrc NE 0 AND sy-subrc NE 3.
MESSAGE e032(z03_mm).
ENDIF.
START-OF-SELECTION *
START-OF-SELECTION.
PERFORM select_donnees.
=================================================
Liste des ARTICLES impactés pour les prévisions *
=================================================
===================================
PORTEFEUILLE DE COMMANDES D'ACHAT *
===================================
Construction itb_pca à partir de EKKO/EKPO.
w_index_ekpo = 1.
w_index_ekes = 1.
w_index_eket = 1.
w_index_mseg = 1.
SORT itb_ekko BY ebeln. "-FAE26446
SORT itb_ekpo BY ebeln ebelp.
SORT itb_makt BY matnr spras.
SORT itb_eket BY ebeln ebelp.
SORT itb_ekes BY ebeln ebelp.
SORT itb_mseg BY ebeln ebelp.
SORT itb_mkpf BY mblnr mjahr.
SORT itb_marc BY matnr werks. "+FAE26446
FAE 26446 remplacement
LOOP AT itb_ekko.
LOOP AT itb_ekpo.
FROM w_index_ekpo.
IF itb_ekko-ebeln = itb_ekpo-ebeln.
LOOP AT itb_ekpo.
READ TABLE itb_marc WITH KEY
matnr = itb_ekpo-matnr
werks = itb_ekpo-werks BINARY SEARCH.
CHECK sy-subrc = 0.
FAE 26446 fin remplacement
itb_pca-ebeln = itb_ekpo-ebeln.
itb_pca-ebelp = itb_ekpo-ebelp.
itb_pca-lifnr = itb_ekko-lifnr. "-FAE26446
itb_pca-lifnr = itb_ekpo-lifnr. "+FAE26446
itb_pca-ekgrp = itb_ekpo-ekgrp. "+FAE26446
itb_pca-dispo = itb_ekpo-dispo. "+FAE26446
itb_pca-matnr = itb_ekpo-matnr.
itb_pca-werks = itb_ekpo-werks.
Recherche du libellé article
READ TABLE itb_makt
WITH KEY matnr = itb_ekpo-matnr
spras = text-fra
BINARY SEARCH.
IF sy-subrc = 0.
itb_pca-maktx = itb_makt-maktx.
ELSE.
READ TABLE itb_makt
WITH KEY matnr = itb_ekpo-matnr
spras = text-ang
BINARY SEARCH.
IF sy-subrc = 0.
itb_pca-maktx = itb_makt-maktx.
ENDIF.
ENDIF.
IF NOT itb_ekpo-bpumn IS INITIAL.
itb_pca-menge = itb_ekpo-menge * itb_ekpo-bpumz /
itb_ekpo-bpumn.
ENDIF.
Sélect° ds la table EKES des dates de livraisons et des qtés
en transit
CLEAR w_temoin_ar.
CLEAR w_etens.
LOOP AT itb_ekes
FROM w_index_ekes.
IF itb_ekes-ebeln = itb_ekpo-ebeln
AND itb_ekes-ebelp = itb_ekpo-ebelp.
IF itb_ekes-ebtyp = text-arn.
itb_pca-eindt = itb_ekes-eindt.
w_temoin_ar = 'X'.
ELSE.
Si c'est une qté en transit alors on recupere
la quantité et la date.
IF itb_ekes-dabmg < itb_ekes-menge.
itb_pca-qtran = itb_pca-qtran + itb_ekes-menge -
itb_ekes-dabmg.
ENDIF.
IF itb_ekes-etens > w_etens.
w_etens = itb_ekes-etens.
itb_pca-dtran = itb_ekes-eindt.
ENDIF.
ENDIF.
ELSEIF itb_ekes-ebeln > itb_ekpo-ebeln
OR ( itb_ekes-ebeln = itb_ekpo-ebeln
AND itb_ekes-ebelp > itb_ekpo-ebelp ).
w_index_ekes = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
S'il n'y a pas d'AR alors récupérat° de la date livraison dans EKET.
LOOP AT itb_eket
FROM w_index_eket.
IF itb_eket-ebeln = itb_ekpo-ebeln
AND itb_eket-ebelp = itb_ekpo-ebelp.
IF w_temoin_ar IS INITIAL.
itb_pca-eindt = itb_eket-eindt.
ENDIF.
itb_pca-slfdt = itb_eket-slfdt.
Calcul du portefeuille fournisseur à partir de la
qté commandée et la qté reçue
itb_pca-attdu = itb_pca-attdu + itb_eket-menge -
itb_eket-wemng.
Calcul du montant du poste
itb_pca-netpr = itb_ekpo-netpr * itb_pca-attdu.
IF itb_ekpo-peinh NE 0.
itb_pca-netpr = itb_pca-netpr / itb_ekpo-peinh.
ENDIF.
Calcul quantité réceptionnée.
itb_pca-wemng = itb_pca-wemng + itb_eket-wemng.
Calcul du retard en nombre de jours calendaires
Le calcul du retard ne doit pas prendre en compte
le jour de livraison
ADD 1 TO itb_eket-eindt.
IF NOT itb_pca-attdu IS INITIAL
AND itb_eket-eindt LT sy-datum.
Calcul du retard en nombre de jours ouvrés
CLEAR w_retard.
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_PERIOD'
EXPORTING
date_deb = itb_eket-eindt
date_fin = sy-datum
IMPORTING
jours = w_retard.
itb_pca-rtard = itb_pca-rtard + w_retard .
ENDIF.
ELSEIF itb_eket-ebeln > itb_ekpo-ebeln
OR ( itb_eket-ebeln = itb_ekpo-ebeln
AND itb_eket-ebelp > itb_ekpo-ebelp ).
w_index_eket = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
Recherche de la derniere date de livraison.
LOOP AT itb_mseg
FROM w_index_mseg.
IF itb_mseg-ebeln = itb_ekpo-ebeln
AND itb_mseg-ebelp = itb_ekpo-ebelp.
READ TABLE itb_mkpf
WITH KEY mblnr = itb_mseg-mblnr
mjahr = itb_mseg-mjahr
BINARY SEARCH.
IF sy-subrc = 0.
IF itb_mkpf-bldat > itb_pca-bldat.
itb_pca-bldat = itb_mkpf-bldat.
ENDIF.
ENDIF.
ELSEIF itb_mseg-ebeln > itb_ekpo-ebeln
OR ( itb_mseg-ebeln = itb_ekpo-ebeln
AND itb_mseg-ebelp > itb_ekpo-ebelp ).
w_index_mseg = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
APPEND itb_pca.
CLEAR itb_pca.
FAE26446 suppression parag. suivant
ELSEIF itb_ekpo-ebeln > itb_ekko-ebeln.
w_index_ekpo = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
Fin FAE26446
ENDLOOP.
=========================
PREVISIONS DE COMMANDES *
=========================
SORT itb_eord BY matnr werks lifnr ekgrp.
SORT itb_eban BY matnr werks flief ekgrp.
SORT itb_plaf BY matnr plwrk flief.
SORT itb_z03_bw_cmp1 BY matnr werks.
SORT itb_z03_bw_cmp2 BY matnr werks."+DE3K937051
SORT itb_pca BY matnr werks lifnr.
w_index_eban = 1.
w_index_plaf = 1.
w_index_z03_bw_cmp1 = 1.
w_index_pca = 1.
w_index_z03_bw_cmp2 = 1."+DE3K937051
Remplissage de la table des prévisions de commande.
LOOP AT itb_eord.
CLEAR: str_prev_pfc,
w_trouve.
MOVE-CORRESPONDING itb_eord TO str_index1.
MOVE-CORRESPONDING itb_eord TO str_index3_eord.
MOVE-CORRESPONDING itb_eord TO itb_prev_cde.
Recherche dans table division/article (MARC) afin de déterminer si
article PFS (prod fabriqué à stock) ou PFC (Prod fabriqué sur cde)
AT NEW werks.
READ TABLE itb_marc_eord
WITH KEY matnr = itb_eord-matnr
werks = itb_eord-werks
BINARY SEARCH.
IF sy-subrc NE 0.
CLEAR itb_marc_eord.
ENDIF.
ENDAT.
a - Prévisions pour les PFS : DA + OP *
*Calcul des quantités de commande.
IF itb_eord-disls = text-tl1.
itb_prev_cde-bstmi = itb_eord-bstfe.
ELSEIF itb_eord-disls = text-tl2
OR itb_eord-disls = text-tl3.
IF itb_eord-bstrf NE 0
AND itb_eord-bstmi = 0
AND itb_eord-bstma = 0.
itb_prev_cde-bstmi = itb_eord-bstrf.
ELSEIF itb_eord-bstrf NE 0
AND itb_eord-bstmi NE 0.
itb_prev_cde-bstmi = itb_eord-bstmi.
ELSEIF itb_eord-bstrf = itb_eord-bstma
AND itb_eord-bstrf NE 0
AND itb_eord-bstmi = 0.
itb_prev_cde-bstmi = itb_eord-bstma.
ENDIF.
ENDIF.
si article PFS (Prod fabriqué à stock) recherche des
demandes d'achat ou ordres planfiés
IF itb_marc_eord-strgr IN r_type_pfs.
Récupérat° calendrier de la division pour calcul correct lors de
l'ajout de eban-webaz ou plaf-webaz jours ouvrés
CLEAR w_trouve_pfs ."+DE3K937051
READ TABLE itb_t001w
WITH KEY werks = itb_eord-werks
BINARY SEARCH.
IF sy-subrc = 0.
LOOP AT itb_eban
FROM w_index_eban.
MOVE-CORRESPONDING itb_eban TO str_index2.
IF str_index1 = str_index2.
w_trouve_pfs = 'X'."+DE3K937051
si qte commandées pour la DA < quantité de la DA
IF itb_eban-bsmng < itb_eban-menge.
ajout de quantité de la DA - qte commandée pour la DA
PERFORM affect_da.
ENDIF.
ELSEIF str_index2 > str_index1.
w_index_eban = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
ENDIF.
ajout des quantité des OP (ordres planifiés)
LOOP AT itb_plaf
FROM w_index_plaf.
MOVE-CORRESPONDING itb_plaf TO str_index4.
str_index4-werks = itb_plaf-plwrk.
str_index4-lifnr = itb_plaf-flief.
IF str_index4 = str_index3_eord.
Ajout de webaz jours ouvrés à pedtr
CALL FUNCTION 'Z_03_MM_ADD_TO_FACTORYDATE'
EXPORTING
i_date = itb_plaf-pedtr
i_calendar_id = itb_t001w-fabkl
i_nb_days = itb_plaf-webaz
IMPORTING
o_date = w_dat_op
EXCEPTIONS
conv_error = 1
OTHERS = 2.
IF sy-subrc
If forecasts found in Z03_BW_CMP2 for the article
IF w_trouve_pfs = 'X'."-DE3K937602
Recalculation prev month M in fct of Nb of wrought days of the month
IF NOT itb_prev_cde-men00 IS INITIAL.
one does not hold any more account of the day in progress
w_lendemain = w_date0 + 1.
CLEAR:w_nb_j,w_nb_j_tot. "DE3K938206+
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_PERIOD'
EXPORTING
date_deb = w_lendemain
date_fin = w_fin_mois
IMPORTING
jours = w_nb_j.
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_MONTH'
EXPORTING
date = w_lendemain
IMPORTING
jours = w_nb_j_tot.
itb_prev_cde-men00 = itb_prev_cde-men00 * w_nb_j / w_nb_j_tot
*CLA DE3K925301 FAE27197
*to round has the higher entirety
itb_prev_cde-men00 = ceil( itb_prev_cde-men00 ). "DE3K938206-
ENDIF.
ENDIF."-DE3K937602
*End change BNI
b - Prévisions pour les PFC (Z03_BW_CMP1 puis rééquilibrage) *
Recherche des previsions dans Z03_BW_CMP1
si article PFC (Prod fabriqué sur cde) recherche des prévisions
IF NOT itb_marc_eord-strgr IN r_type_pfs.
CLEAR str_prev_pfc.
MOVE-CORRESPONDING itb_eord TO str_prev_pfc.
CLEAR w_trouve_pfc .
LOOP AT itb_z03_bw_cmp1
FROM w_index_z03_bw_cmp1.
MOVE-CORRESPONDING itb_z03_bw_cmp1 TO str_index7.
MOVE-CORRESPONDING itb_eord TO str_index6.
IF str_index6 = str_index7.
si on trouve des prévisions dans z03_bw_cmp1 pour la source
d'appro eord alors c'est un article PFC
w_trouve_pfc = 'X'.
CASE itb_z03_bw_cmp1-pdatu+0(6).
WHEN w_date0+0(6).
str_prev_pfc-men00 = itb_z03_bw_cmp1-plnmg.
WHEN w_date1+0(6).
str_prev_pfc-men01 = itb_z03_bw_cmp1-plnmg.
WHEN w_date2+0(6).
str_prev_pfc-men02 = itb_z03_bw_cmp1-plnmg.
WHEN w_date3+0(6).
str_prev_pfc-men03 = itb_z03_bw_cmp1-plnmg.
WHEN w_date4+0(6).
str_prev_pfc-men04 = itb_z03_bw_cmp1-plnmg.
WHEN w_date5+0(6).
str_prev_pfc-men05 = itb_z03_bw_cmp1-plnmg.
WHEN w_date6+0(6).
str_prev_pfc-men06 = itb_z03_bw_cmp1-plnmg.
WHEN OTHERS.
ENDCASE.
ELSEIF str_index7 > str_index6.
w_index_z03_bw_cmp1 = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
*Begin change BNI
Si des prévisions trouvées dans Z03_BW_CMP1 pour l'article
IF w_trouve_pfc = 'X'.
Recalcul prev mois M en fct du nb de jours ouvrés du mois
IF NOT str_prev_pfc-men00 IS INITIAL.
on ne tient plus compte du jour en cours
w_lendemain = w_date0 + 1.
CLEAR:w_nb_j,w_nb_j_tot. "DE3K938206+
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_PERIOD'
EXPORTING
date_deb = w_lendemain
date_fin = w_fin_mois
IMPORTING
jours = w_nb_j.
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_MONTH'
EXPORTING
date = w_lendemain
IMPORTING
jours = w_nb_j_tot.
str_prev_pfc-men00 = str_prev_pfc-men00 * w_nb_j / w_nb_j_tot.
*CLA DE3K925301 FAE27197
*arrondir a l'entier supèrieur
str_prev_pfc-men00 = ceil( str_prev_pfc-men00 ).
ENDIF.
Equilibrage PFC : commande/prévision du mois
Recherche COMMANDES cumulées pour M à M+6
CLEAR str_pca_pfc.
LOOP AT itb_pca
FROM w_index_pca.
MOVE-CORRESPONDING itb_pca TO str_index5.
IF str_index5 = str_index3_eord.
IF NOT itb_pca-menge IS INITIAL.
CASE itb_pca-eindt+0(6).
WHEN w_date0+0(6).
IF itb_pca-eindt >= w_date0.
str_pca_pfc-men00 = str_pca_pfc-men00 + itb_pca-menge.
ENDIF.
WHEN w_date1+0(6).
str_pca_pfc-men01 = str_pca_pfc-men01 + itb_pca-menge.
WHEN w_date2+0(6).
str_pca_pfc-men02 = str_pca_pfc-men02 + itb_pca-menge.
WHEN w_date3+0(6).
str_pca_pfc-men03 = str_pca_pfc-men03 + itb_pca-menge.
WHEN w_date4+0(6).
str_pca_pfc-men04 = str_pca_pfc-men04 + itb_pca-menge.
WHEN w_date5+0(6).
str_pca_pfc-men05 = str_pca_pfc-men05 + itb_pca-menge.
WHEN w_date6+0(6).
str_pca_pfc-men06 = str_pca_pfc-men06 + itb_pca-menge.
ENDCASE.
ENDIF."NOT itb_pca-menge IS INITIAL
ELSEIF str_index5 > str_index3_eord.
w_index_pca = sy-tabix.
EXIT.
ENDIF.
ENDLOOP."itb_pca
*. Equilibrer commande / prévision des mois : diminuer la quantité de
prévision de chaque mois par le portefeuille de commande client du
mois*. Si ce solde est négatif alors lui donner la valeur 0.
w_i = 0.
Ajustement commandes/prévisions pour les mois M à M+6
WHILE w_i .
Pour un mois, SI Prévisions > Commandes en cours
IF .
Prévisions = Prévisions - Commandes en cours
= 0.
ENDIF.
On passe au mois suivant
w_i = w_i + 1.
ENDWHILE.
MOVE str_prev_pfc-men00 TO itb_prev_cde-men00.
MOVE str_prev_pfc-men01 TO itb_prev_cde-men01.
MOVE str_prev_pfc-men02 TO itb_prev_cde-men02.
MOVE str_prev_pfc-men03 TO itb_prev_cde-men03.
MOVE str_prev_pfc-men04 TO itb_prev_cde-men04.
MOVE str_prev_pfc-men05 TO itb_prev_cde-men05.
MOVE str_prev_pfc-men06 TO itb_prev_cde-men06.
Hi
You check in SM50 by executing the programing, You will come to know which select is taking more time and accordingly you modify that select.
You can do SQL trace and Run time analysis and analyse and see.
check this and use
1) Dont use nested select statements
2) If possible use for all entries in addition
3) In the where addition make sure you give all the primary key
4) Use Index for the selection criteria.
5) You can also use inner joins
6) You can try to put the data from the first select statement into an Itab and then in order to select the data from the second table use for all entries in.
7) Use the runtime analysis SE30 and SQL Trace (ST05) to identify the performance and also to identify where the load is heavy, so that you can change the code accordingly
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/5d0db4c9-0e01-0010-b68f-9b1408d5f234
ABAP performance depends upon various factors and in devicded in three parts:
1. Database
2. ABAP
3. System
Run Any program using SE30 (performance analys) to improve performance refer to tips and trics section of SE30, Always remember that ABAP perfirmance is improved when there is least load on Database.
u can get an interactive grap in SE30 regarding this with a file.
also if u find runtime of parts of codes then use :
Switch on RTA Dynamically within ABAP Code
*To turn runtim analysis on within ABAP code insert the following code
SET RUN TIME ANALYZER ON.
*To turn runtim analysis off within ABAP code insert the following code
SET RUN TIME ANALYZER OFF.
Always check the driver internal tables is not empty, while using FOR ALL ENTRIES
Avoid for all entries in JOINS
Try to avoid joins and use FOR ALL ENTRIES.
Try to restrict the joins to 1 level only ie only for tables
Avoid using Select *.
Avoid having multiple Selects from the same table in the same object.
Try to minimize the number of variables to save memory.
The sequence of fields in 'where clause' must be as per primary/secondary index ( if any)
Avoid creation of index as far as possible
Avoid operators like <>, > , < & like % in where clause conditions
Avoid select/select single statements in loops.
Try to use 'binary search' in READ internal table. Ensure table is sorted before using BINARY SEARCH.
Avoid using aggregate functions (SUM, MAX etc) in selects ( GROUP BY , HAVING,)
Avoid using ORDER BY in selects
Avoid Nested Selects
Avoid Nested Loops of Internal Tables
Try to use FIELD SYMBOLS.
Try to avoid into Corresponding Fields of
Avoid using Select Distinct, Use DELETE ADJACENT
Check the following Links
Re: performance tuning
Re: Performance tuning of program
http://www.sapgenie.com/abap/performance.htm
http://www.thespot4sap.com/Articles/SAPABAPPerformanceTuning_PerformanceAnalysisTools.asp
check the below link
http://www.sap-img.com/abap/performance-tuning-for-data-selection-statement.htm
See the following link if it's any help:
http://www.thespot4sap.com/Articles/SAPABAPPerformanceTuning_PerformanceAnalysisTools.asp
Check also http://service.sap.com/performance
and
books like
http://www.sap-press.com/product.cfm?account=&product=H951
http://www.sap-press.com/product.cfm?account=&product=H973
http://www.sap-img.com/abap/more-than-100-abap-interview-faqs.htm
http://www.thespot4sap.com/Articles/SAPABAPPerformanceTuning_PerformanceAnalysisTools.asp
Performance tuning for Data Selection Statement
http://www.sap-img.com/abap/performance-tuning-for-data-selection-statement.htm
Debugger
http://help.sap.com/saphelp_47x200/helpdata/en/c6/617ca9e68c11d2b2ab080009b43351/content.htm
http://www.cba.nau.edu/haney-j/CIS497/Assignments/Debugging.doc
http://help.sap.com/saphelp_erp2005/helpdata/en/b3/d322540c3beb4ba53795784eebb680/frameset.htm
Run Time Analyser
http://help.sap.com/saphelp_47x200/helpdata/en/c6/617cafe68c11d2b2ab080009b43351/content.htm
SQL trace
http://help.sap.com/saphelp_47x200/helpdata/en/d1/801f7c454211d189710000e8322d00/content.htm
CATT - Computer Aided Testing Too
http://help.sap.com/saphelp_47x200/helpdata/en/b3/410b37233f7c6fe10000009b38f936/frameset.htm
Test Workbench
http://help.sap.com/saphelp_47x200/helpdata/en/a8/157235d0fa8742e10000009b38f889/frameset.htm
Coverage Analyser
http://help.sap.com/saphelp_47x200/helpdata/en/c7/af9a79061a11d4b3d4080009b43351/content.htm
Runtime Monitor
http://help.sap.com/saphelp_47x200/helpdata/en/b5/fa121cc15911d5993d00508b6b8b11/content.htm
Memory Inspector
http://help.sap.com/saphelp_47x200/helpdata/en/a2/e5fc84cc87964cb2c29f584152d74e/content.htm
ECATT - Extended Computer Aided testing tool.
http://help.sap.com/saphelp_47x200/helpdata/en/20/e81c3b84e65e7be10000000a11402f/frameset.htm
Just refer to these links...
performance
Performance
Performance Guide
performance issues...
Performance Tuning
Performance issues
performance tuning
performance tuning
You can go to the transaction SE30 to have the runtime analysis of your program.Also try the transaction SCI , which is SAP Code Inspector.
1 Always check the driver internal tables is not empty, while using FOR ALL ENTRIES
2 Avoid for all entries in JOINS
3 Try to avoid joins and use FOR ALL ENTRIES.
4 Try to restrict the joins to 1 level only ie only for 2 tables
5 Avoid using Select *.
6 Avoid having multiple Selects from the same table in the same object.
7 Try to minimize the number of variables to save memory.
8 The sequence of fields in 'where clause' must be as per primary/secondary index ( if any)
9 Avoid creation of index as far as possible
10 Avoid operators like <>, > , < & like % in where clause conditions
11 Avoid select/select single statements in loops.
12 Try to use 'binary search' in READ internal table. Ensure table is sorted before using BINARY SEARCH.
13 Avoid using aggregate functions (SUM, MAX etc) in selects ( GROUP BY , HAVING,)
14 Avoid using ORDER BY in selects
15 Avoid Nested Selects
16 Avoid Nested Loops of Internal Tables
17 Try to use FIELD SYMBOLS.
18 Try to avoid into Corresponding Fields of
19 Avoid using Select Distinct, Use DELETE ADJACENT.
Regards
Anji -
Hi how to improve performence of this program
Hi all,
How to improve the performence of this program.....................
REPORT z03_gil010 NO STANDARD PAGE HEADING LINE-SIZE 130.
INCLUDE *
INCLUDE: z00_bci010. " Gestion des anomalies.
Déclaration des données *
Tables de la bases de données *
TABLES:
ekpo, " Poste document d'achat.
lfa1, " Base fournisseurs (généralités).
marc, " Données division de l'article.
z03_bw_cmp1,
eord, "Répertoire des sources appro. Achats
eina, "Fiche infos-achats - données générales
t024, "Groupes d'acheteurs
tvarv. "FAE17345+
Déclaration des données internes *
Déclaration de la table interne qui permet de recuperer les mois.
DATA: BEGIN OF itb_months OCCURS 12.
INCLUDE STRUCTURE t247.
DATA: END OF itb_months.
Table pour récupération d'infos sur les divisions
DATA: BEGIN OF itb_t001w OCCURS 0,
werks LIKE t001w-werks,
fabkl LIKE t001w-fabkl," Clé du calendrier d'entreprise
END OF itb_t001w.
Déclaration de la table interne contenant les infos sur l'adresse du
fournisseur.
DATA: BEGIN OF itb_adresse OCCURS 0,
lifnr LIKE lfa1-lifnr, " Numéro de compte fournisseur.
name1 LIKE lfa1-name1, " Nom 1.
name2 LIKE lfa1-name2, " Nom 2.
name3 LIKE lfa1-name3, " Nom 3.
name4 LIKE lfa1-name4, " Nom 4.
stras LIKE lfa1-stras, " N° de rue et nom de la rue.
pstlz LIKE lfa1-pstlz, " Code postal.
ort01 LIKE lfa1-ort01, " Localité.
pfach LIKE lfa1-pfach, " Boîte postale.
pstl2 LIKE lfa1-pstl2, " Code de la boîte postale.
land1 LIKE lfa1-land1, " Clé de pays.
landx LIKE t005t-landx, " Pays.
spras LIKE lfa1-spras, " Code langue
END OF itb_adresse.
Déclaration d'une table interne pour les informations sur les
prévisions de commande.
DATA: BEGIN OF itb_prev_cde OCCURS 0,
werks LIKE marc-werks, " Division
idnlf LIKE eina-idnlf, " ADDsde ref article frn
lifnr LIKE eord-lifnr, " N° fournisseur.
ekgrp LIKE marc-ekgrp, " Groupe d'acheteurs
dispo LIKE marc-dispo, " Code gestionnaire MRP
matnr LIKE eord-matnr, " Article.
maktx LIKE makt-maktx, " Désignation article.
bstmi LIKE marc-bstmi, " Quantité de commande.
men00 LIKE plaf-gsmng, " Quantité du mois en cours M.
men01 LIKE plaf-gsmng, " Quantité pour le mois M+1.
men02 LIKE plaf-gsmng, " Quantité pour le mois M+2.
men03 LIKE plaf-gsmng, " Quantité pour le mois M+3.
men04 LIKE plaf-gsmng, " Quantité pour le mois M+4.
men05 LIKE plaf-gsmng, " Quantité pour le mois M+5.
men06 LIKE plaf-gsmng. " Quantité pour le mois M+6.
DATA: END OF itb_prev_cde.
Structure de travail pour les commandes convernant les PFC
DATA str_pca_pfc LIKE itb_prev_cde.
*add sde
DATA str_eord_pfc LIKE itb_prev_cde.
Structure de travail pour les prévisons PFC
DATA str_prev_pfc LIKE itb_prev_cde.
Déclaration d'une table interne pour les informations sur le
portefeuille des commandes d'achat.
DATA: BEGIN OF itb_pca OCCURS 0,
werks LIKE ekpo-werks, " Division
idnlf LIKE eina-idnlf, " ADDsde ref article frn
lifnr LIKE eord-lifnr, " N° fournisseur.
ekgrp LIKE marc-ekgrp, " Groupe d'acheteurs
dispo LIKE marc-dispo, " Code gestionnaire MRP
matnr LIKE eord-matnr, " Article.
maktx LIKE makt-maktx, " Désignation article.
ebeln LIKE ekes-ebeln, " Numéro du document d'achat.
ebelp LIKE ekes-ebelp, " Numéro de poste du document d'achat.
slfdt LIKE eket-slfdt, " Date de livraison statistique
eindt LIKE ekes-eindt, " Date de livraison indiquée dans la
" confirmation de la cde.
menge LIKE ekes-menge, " Quantité indiquée dans la confirma-
" tion de la commande.
attdu LIKE eket-wemng, " Portefeuille fournisseur.
netpr LIKE ekpo-brtwr, " Prix net du document d'achat dans
" la devise du document.
rtard TYPE i, " Retard en jours ouvres.
wemng LIKE eket-wemng, " Quantité de l'entrée de marchandise.
bldat LIKE mkpf-bldat, " Date inscrite sur la pièce/sur le
" document.
qtran LIKE ekes-menge, " Quantité en transit.
dtran LIKE ekes-eindt. " Date du dernier avis de transit.
DATA: END OF itb_pca.
DATA: w_i TYPE i, "Compteur
w_i_char(1) TYPE c, "Texte pour récupérer compteur
w_nm_zone(20) TYPE c, "Nom zone pour assign au field-symbols
w_nb_j TYPE i, "Nb de jours ouvrés jusqu'à fin mois
w_nb_j_tot TYPE i. "Nb de jours ouvrés du mois
FIELD-SYMBOLS: TYPE ANY.
Déclaration d'une table contenant les fiches info achat.
DATA: BEGIN OF itb_eina OCCURS 0,
matnr LIKE eina-matnr,
lifnr LIKE eina-lifnr,
idfnl LIKE eina-idnlf.
DATA: END OF itb_eina.
Déclaration d'une table contenant les infos groupe acheteur.
*DATA: BEGIN OF itb_t024 OCCURS 0,
ekgrp LIKE t024-ekgrp,
eknam LIKE t024-eknam,
ektel LIKE t024-ektel,
telfx LIKE t024-telfx.
*DATA: END OF itb_t024.
Déclaration d'une table pour le transfert du fichier.
DATA: BEGIN OF itb_transfert OCCURS 0,
col00(8), "division
col00bis(20), "Reference article
col01(18), "No article
col02(45), "libelle article
col021(17), "Groupe acheteur
col022(13), "gestionnaire
col03(17), "qte commandée ou No de commande
col04(13), "Mois 1 ou No poste cde
col05(20), "Mois 2 ou délai initial
col06(33), "Mois 3 ou délai négocié
col07(13), "Mois 4 ou qté cdée
col08(13), "Mois 5 ou qté attendue
col09(13), "Mois 6 ou Montant attendu
col10(13), "Mois 7 ou retard
col11(13), "qte partielle livree
col12(13), "date livraison partielle
col13(13), "qté en transit
col14(13). "date
DATA: END OF itb_transfert.
Déclaration d'une table contenant la liste des fournisseurs.
DATA: BEGIN OF itb_lifnr OCCURS 0,
werks LIKE marc-werks,
idfnl LIKE eina-idnlf,
lifnr LIKE eord-lifnr,
ekgrp LIKE marc-ekgrp,
spras LIKE lfa1-spras,
eknam LIKE t024-eknam,
ektel LIKE t024-ektel,
telfx LIKE t024-telfx.
DATA: END OF itb_lifnr.
Déclaration d'une structure pour la selection dans la table MSEG.
DATA : BEGIN OF itb_mseg OCCURS 0,
mblnr LIKE mseg-mblnr,
mjahr LIKE mseg-mjahr,
ebeln LIKE mseg-ebeln,
ebelp LIKE mseg-ebelp,
END OF itb_mseg.
déclaration d'une structure pour la selection dans EKPO.
DATA : BEGIN OF itb_ekpo OCCURS 0,
lifnr LIKE ekko-lifnr,
ebeln LIKE ekpo-ebeln,
ebelp LIKE ekpo-ebelp,
menge LIKE ekpo-menge,
bpumz LIKE ekpo-bpumz,
bpumn LIKE ekpo-bpumn,
matnr LIKE ekpo-matnr,
werks LIKE ekpo-werks,
netpr LIKE ekpo-netpr,
peinh LIKE ekpo-peinh, "Base de prix FAE17345+
ekgrp LIKE ekko-ekgrp, "AFT++
dispo LIKE marc-dispo, "AFT++
END OF itb_ekpo.
déclaration d'une structure pour la selection dans EKPO.
DATA : BEGIN OF itb_ekko OCCURS 0,
ebeln LIKE ekko-ebeln,
lifnr LIKE ekko-lifnr,
spras LIKE ekko-spras,
END OF itb_ekko.
déclaration d'une structure pour la selection dans EKES.
DATA : BEGIN OF itb_ekes OCCURS 0,
ebeln LIKE eket-ebeln,
ebelp LIKE eket-ebelp,
ebtyp LIKE ekes-ebtyp,
eindt LIKE ekes-eindt,
menge LIKE ekes-menge,
dabmg LIKE ekes-dabmg,
etens LIKE ekes-etens,
END OF itb_ekes.
déclaration d'une structure pour la selection dans EKET
DATA : BEGIN OF itb_eket OCCURS 0,
ebeln LIKE eket-ebeln,
ebelp LIKE eket-ebelp,
menge LIKE eket-menge,
wemng LIKE eket-wemng,
eindt LIKE eket-eindt,
slfdt LIKE eket-slfdt,
END OF itb_eket.
déclaration d'une structure pour la selection dans MKPF.
DATA : BEGIN OF itb_mkpf OCCURS 0,
mblnr LIKE mkpf-mblnr,
mjahr LIKE mkpf-mjahr,
bldat LIKE mkpf-bldat,
END OF itb_mkpf.
Déclaration d'une structure pour la sélection dans EORD.
DATA : BEGIN OF itb_eord OCCURS 0,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
lifnr LIKE eord-lifnr,
ekgrp LIKE marc-ekgrp,
dispo LIKE marc-dispo, "DE3K924352
disls LIKE marc-disls,
bstfe LIKE marc-bstfe,
bstrf LIKE marc-bstrf,
bstmi LIKE marc-bstmi,
bstma LIKE marc-bstma,
END OF itb_eord.
DATA : BEGIN OF itb_eordw OCCURS 0.
INCLUDE STRUCTURE itb_eord.
DATA : END OF itb_eordw.
Déclaration d'une structure pour la sélection dans MAKT.
DATA : BEGIN OF itb_makt OCCURS 0,
matnr LIKE makt-matnr,
spras LIKE makt-spras,
maktx LIKE makt-maktx,
END OF itb_makt.
Déclaration d'une structure pour la sélection dans EBAN.
DATA : BEGIN OF itb_eban OCCURS 0,
matnr LIKE eban-matnr,
werks LIKE eban-werks,
flief LIKE eban-flief,
lfdat LIKE eban-lfdat,
menge LIKE eban-menge,
bsmng LIKE eban-bsmng,
webaz LIKE eban-webaz,
ekgrp LIKE eban-ekgrp,
ebeln LIKE eban-ebeln,
banfn LIKE eban-banfn,
bnfpo LIKE eban-bnfpo, "DB3K900702+
END OF itb_eban.
Déclaration d'une structure pour la sélection dans PLAF.
DATA : BEGIN OF itb_plaf OCCURS 0,
plnum LIKE plaf-plnum, "DB3K900702+
matnr LIKE plaf-matnr,
plwrk LIKE plaf-plwrk,
flief LIKE plaf-flief,
pedtr LIKE plaf-pedtr,
gsmng LIKE plaf-gsmng,
webaz LIKE plaf-webaz,
END OF itb_plaf.
Déclaration d'une structure pour la sélection dans MARC.
DATA : BEGIN OF itb_marc OCCURS 0,
matnr LIKE marc-matnr,
werks LIKE marc-werks,
disls LIKE marc-disls,
bstrf LIKE marc-bstrf,
bstmi LIKE marc-bstmi,
bstma LIKE marc-bstma,
bstfe LIKE marc-bstfe,
ekgrp LIKE marc-ekgrp,
dispo LIKE marc-dispo,
END OF itb_marc.
DATA : BEGIN OF itb_marc_eord OCCURS 0,
matnr LIKE marc-matnr,
werks LIKE marc-werks,
strgr LIKE marc-strgr, "groupe de stratégie planif
END OF itb_marc_eord.
DATA : BEGIN OF itb_z03_bw_cmp1 OCCURS 0,
matnr LIKE z03_bw_cmp1-matnr,
werks LIKE z03_bw_cmp1-werks,
pdatu LIKE z03_bw_cmp1-pdatu,
plnmg LIKE z03_bw_cmp1-plnmg,
END OF itb_z03_bw_cmp1.
Begin change BNI <DE3K937051>
DATA : BEGIN OF itb_z03_bw_cmp2 OCCURS 0,
matnr LIKE z03_bw_cmp2-matnr,
werks LIKE z03_bw_cmp2-werks,
pdatu LIKE z03_bw_cmp2-pdatu,
plnmg LIKE z03_bw_cmp2-plnmg,
END OF itb_z03_bw_cmp2.
*End change BNI
DATA : BEGIN OF str_index1,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index1.
DATA : BEGIN OF str_index2,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index2.
DATA : BEGIN OF str_index3_eord,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index3_eord.
DATA : BEGIN OF str_index4,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index4.
DATA : BEGIN OF str_index5,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index5.
DATA : BEGIN OF str_index6,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index6.
DATA : BEGIN OF str_index7,
matnr LIKE eord-matnr,
werks LIKE eord-werks,
END OF str_index7.
Déclaration des variables de debut et de fin de mois.
DATA: w_debut_mois LIKE sy-datum,
w_debut_periode LIKE sy-datum,
w_fin_mois LIKE sy-datum,
w_fin_periode LIKE sy-datum.
Déclaration des variables pour les dates.
DATA: w_date0 LIKE sy-datum,
w_date1 LIKE sy-datum,
w_date2 LIKE sy-datum,
w_date3 LIKE sy-datum,
w_date4 LIKE sy-datum,
w_date5 LIKE sy-datum,
w_date6 LIKE sy-datum,
w_datejour LIKE sy-datum, "FAE15269
w_dat_da LIKE eban-lfdat,
w_dat_op LIKE plaf-pedtr,
w_mois0 LIKE t247-ltx,
w_mois1 LIKE t247-ltx,
w_mois2 LIKE t247-ltx,
w_mois3 LIKE t247-ltx,
w_mois4 LIKE t247-ltx,
w_mois5 LIKE t247-ltx,
w_mois6 LIKE t247-ltx,
w_lendemain LIKE sy-datum. "FAE17345+
Temoin d'un AR dans la commande d'achat.
DATA: w_temoin_ar.
Numéro de la confirmation de la commande
DATA : w_etens LIKE ekes-etens.
Déclaration des variables pour le nom des fichiers.
DATA: w_nom_fichier LIKE rlgrap-filename,
w_fichier LIKE rlgrap-filename,
w_racine LIKE rlgrap-filename,
w_file LIKE rlgrap-filename.
Déclaration d'une table interne pour le transfert.
DATA: BEGIN OF itb_trans OCCURS 0,
w_ligne(320).
DATA: END OF itb_trans.
Déclaration d'une variable pour rechercher les enregistrements vides.
DATA: w_compteur TYPE i,
w_compteur1 TYPE i,
w_compteur2 TYPE i,
w_retard TYPE i, " Retard en jours ouvres.
w_trouve_pfc TYPE c, "addsde
w_trouve_pfs TYPE c, "+DE3K937051
w_trouve TYPE c.
*Index pour les LOOP
DATA : w_index_ekpo LIKE sy-tabix,
w_index_ekes LIKE sy-tabix,
w_index_eket LIKE sy-tabix,
w_index_mseg LIKE sy-tabix,
w_index_eban LIKE sy-tabix,
w_index_plaf LIKE sy-tabix,
w_index_pca LIKE sy-tabix,
w_index_z03_bw_cmp1 LIKE sy-tabix,
w_index_z03_bw_cmp2 LIKE sy-tabix."+DE3K937051
RANGES : r_type_pfs FOR marc-strgr.
*fichier sur serveur +EDR231003
DATA : w_chemin LIKE filename-fileintern, "nom du fichier
w_date_fichier(12) TYPE c, "Date format DD_MM_AA
w_csv(307) TYPE c. "ligne du fichier format CSV
CONSTANTS: k_imputation_m LIKE eban-knttp VALUE 'M'. "FAE19001+
Description de l écran de sélection *
Paramètres "UTILISATION" *
Ouverture d'un block de sélection pour le(s) fournisseur(s).
SELECTION-SCREEN BEGIN OF BLOCK block1 WITH FRAME TITLE text-bl1.
Sélection division(s)
SELECT-OPTIONS: s_werks FOR ekpo-werks.
Sélection fournisseur(s).
SELECT-OPTIONS: s_lifnr FOR lfa1-lifnr OBLIGATORY.
Sélection du Groupe d'acheteur
*SELECT-OPTIONS: s_ekgrp FOR marc-ekgrp. "-FAE26446
*SELECT-OPTIONS: s_dispo FOR marc-dispo. "-FAE26446
SELECTION-SCREEN END OF BLOCK block1.
FAE 26446 : ajout
SELECTION-SCREEN BEGIN OF BLOCK block3 WITH FRAME TITLE text-bl3.
SELECTION-SCREEN BEGIN OF LINE.
PARAMETER p_ekgrp RADIOBUTTON GROUP g3.
SELECTION-SCREEN COMMENT 5(24) text-001 FOR FIELD p_ekgrp.
SELECT-OPTIONS: s_ekgrp FOR marc-ekgrp.
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN BEGIN OF LINE.
PARAMETER p_dispo RADIOBUTTON GROUP g3.
SELECTION-SCREEN COMMENT 5(24) text-002 FOR FIELD p_dispo.
SELECT-OPTIONS: s_dispo FOR marc-dispo.
SELECTION-SCREEN END OF LINE.
SELECTION-SCREEN END OF BLOCK block3.
FAE 26446 : fin ajout
Paramètres "SYSTEME" *
Saut de 2 lignes.
SELECTION-SCREEN: SKIP 2.
Ouverture d'un block de sélection pour l'adresse physique du fichier.
SELECTION-SCREEN BEGIN OF BLOCK block2 WITH FRAME TITLE text-bl2.
PARAMETERS: p_pc RADIOBUTTON GROUP rad1 DEFAULT 'X', "+EDR231003
p_fic_pc LIKE rlgrap-filename. "+EDR231003
SELECTION-SCREEN SKIP. "+EDR231003
PARAMETERS : p_serve RADIOBUTTON GROUP rad1, "+EDR231003
p_fic_se LIKE filename-fileintern "+EDR231003
DEFAULT 'Z03_PREV_COMMANDES'. "+EDR231003
SELECTION-SCREEN END OF BLOCK block2.
Logique de traitement *
INITIALIZATION *
INITIALIZATION.
Date du jour
MOVE sy-datum TO w_datejour. "FAE15269
Gestion des anomalies.
MOVE text-lb1 TO w_lb_traitement.
PERFORM f930_init USING sy-cprog '30'.
Fin de la gestions des anomalies.
Récuperation des mois dans la table interne 'ITB_MONTHS'.
CALL FUNCTION 'MONTH_NAMES_GET'
EXPORTING
language = sy-langu
TABLES
month_names = itb_months
EXCEPTIONS
month_names_not_found = 1
OTHERS = 2.
IF sy-subrc <> 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
Récupération des differentes periodes.
PERFORM f100_recuperation_date TABLES itb_months.
Récupération du debut du mois.
CONCATENATE sy-datlo(6) '01' INTO w_debut_mois.
MOVE: w_debut_mois TO w_debut_periode.
Récupération du dernier jour du mois.
CALL FUNCTION 'LAST_DAY_OF_MONTHS'
EXPORTING
day_in = sy-datlo
IMPORTING
last_day_of_month = w_fin_mois
EXCEPTIONS
day_in_no_date = 1
OTHERS = 2.
IF sy-subrc <> 0.
MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ENDIF.
TOP-OF-PAGE *
TOP-OF-PAGE.
CALL FUNCTION 'Z_00_BC_TOP_OF_PAGE'
EXPORTING
p_linsz = k_ligne
p_pagno = sy-pagno
p_prog = sy-cprog
p_projet = k_projet
p_societe = k_societe
p_sujet = sy-title.
END-OF-PAGE *
END-OF-PAGE.
AT SELECTION-SCREEN *
FAE 26446 : ajout
AT SELECTION-SCREEN ON BLOCK block3.
IF NOT ( s_ekgrp IS INITIAL )
AND NOT ( s_dispo IS INITIAL ).
MESSAGE e394(z03_mm).
ENDIF.
IF p_ekgrp = 'X'.
IF s_ekgrp IS INITIAL.
MESSAGE e395(z03_mm).
ENDIF.
ELSE.
IF s_dispo IS INITIAL.
MESSAGE e396(z03_mm).
ENDIF.
ENDIF.
fae26446 fin ajout
AT SELECTION-SCREEN ON BLOCK block2.
IF p_pc = 'X'.
IF p_fic_pc IS INITIAL.
*Attention, il n'y a aucune adresse de sauvegarde pour le(s) fichier(s)
MESSAGE e021(z03_mm).
ENDIF.
ELSE.
IF p_fic_se IS INITIAL.
*Attention, il n'y a aucune adresse de sauvegarde pour le(s) fichier(s)
MESSAGE e021(z03_mm).
ENDIF.
ENDIF.
Création du matchcode pour la selection du fichier local.
AT SELECTION-SCREEN ON VALUE-REQUEST FOR p_fic_pc.
CALL FUNCTION 'WS_FILENAME_GET'
EXPORTING
def_filename = p_fic_pc
def_path = 'C:'
mask = text-ma1
mode = 'S'
title = text-sel
IMPORTING
filename = p_fic_pc
EXCEPTIONS
inv_winsys = 1
no_batch = 2
selection_cancel = 3
selection_error = 4
OTHERS = 5.
IF sy-subrc NE 0 AND sy-subrc NE 3.
MESSAGE e032(z03_mm).
ENDIF.
START-OF-SELECTION *
START-OF-SELECTION.
PERFORM select_donnees.
=================================================
Liste des ARTICLES impactés pour les prévisions *
=================================================
===================================
PORTEFEUILLE DE COMMANDES D'ACHAT *
===================================
Construction itb_pca à partir de EKKO/EKPO.
w_index_ekpo = 1.
w_index_ekes = 1.
w_index_eket = 1.
w_index_mseg = 1.
SORT itb_ekko BY ebeln. "-FAE26446
SORT itb_ekpo BY ebeln ebelp.
SORT itb_makt BY matnr spras.
SORT itb_eket BY ebeln ebelp.
SORT itb_ekes BY ebeln ebelp.
SORT itb_mseg BY ebeln ebelp.
SORT itb_mkpf BY mblnr mjahr.
SORT itb_marc BY matnr werks. "+FAE26446
FAE 26446 remplacement
LOOP AT itb_ekko.
LOOP AT itb_ekpo.
FROM w_index_ekpo.
IF itb_ekko-ebeln = itb_ekpo-ebeln.
LOOP AT itb_ekpo.
READ TABLE itb_marc WITH KEY
matnr = itb_ekpo-matnr
werks = itb_ekpo-werks BINARY SEARCH.
CHECK sy-subrc = 0.
FAE 26446 fin remplacement
itb_pca-ebeln = itb_ekpo-ebeln.
itb_pca-ebelp = itb_ekpo-ebelp.
itb_pca-lifnr = itb_ekko-lifnr. "-FAE26446
itb_pca-lifnr = itb_ekpo-lifnr. "+FAE26446
itb_pca-ekgrp = itb_ekpo-ekgrp. "+FAE26446
itb_pca-dispo = itb_ekpo-dispo. "+FAE26446
itb_pca-matnr = itb_ekpo-matnr.
itb_pca-werks = itb_ekpo-werks.
Recherche du libellé article
READ TABLE itb_makt
WITH KEY matnr = itb_ekpo-matnr
spras = text-fra
BINARY SEARCH.
IF sy-subrc = 0.
itb_pca-maktx = itb_makt-maktx.
ELSE.
READ TABLE itb_makt
WITH KEY matnr = itb_ekpo-matnr
spras = text-ang
BINARY SEARCH.
IF sy-subrc = 0.
itb_pca-maktx = itb_makt-maktx.
ENDIF.
ENDIF.
IF NOT itb_ekpo-bpumn IS INITIAL.
itb_pca-menge = itb_ekpo-menge * itb_ekpo-bpumz /
itb_ekpo-bpumn.
ENDIF.
Sélect° ds la table EKES des dates de livraisons et des qtés
en transit
CLEAR w_temoin_ar.
CLEAR w_etens.
LOOP AT itb_ekes
FROM w_index_ekes.
IF itb_ekes-ebeln = itb_ekpo-ebeln
AND itb_ekes-ebelp = itb_ekpo-ebelp.
IF itb_ekes-ebtyp = text-arn.
itb_pca-eindt = itb_ekes-eindt.
w_temoin_ar = 'X'.
ELSE.
Si c'est une qté en transit alors on recupere
la quantité et la date.
IF itb_ekes-dabmg < itb_ekes-menge.
itb_pca-qtran = itb_pca-qtran + itb_ekes-menge -
itb_ekes-dabmg.
ENDIF.
IF itb_ekes-etens > w_etens.
w_etens = itb_ekes-etens.
itb_pca-dtran = itb_ekes-eindt.
ENDIF.
ENDIF.
ELSEIF itb_ekes-ebeln > itb_ekpo-ebeln
OR ( itb_ekes-ebeln = itb_ekpo-ebeln
AND itb_ekes-ebelp > itb_ekpo-ebelp ).
w_index_ekes = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
S'il n'y a pas d'AR alors récupérat° de la date livraison dans EKET.
LOOP AT itb_eket
FROM w_index_eket.
IF itb_eket-ebeln = itb_ekpo-ebeln
AND itb_eket-ebelp = itb_ekpo-ebelp.
IF w_temoin_ar IS INITIAL.
itb_pca-eindt = itb_eket-eindt.
ENDIF.
itb_pca-slfdt = itb_eket-slfdt.
Calcul du portefeuille fournisseur à partir de la
qté commandée et la qté reçue
itb_pca-attdu = itb_pca-attdu + itb_eket-menge -
itb_eket-wemng.
Calcul du montant du poste
itb_pca-netpr = itb_ekpo-netpr * itb_pca-attdu.
IF itb_ekpo-peinh NE 0.
itb_pca-netpr = itb_pca-netpr / itb_ekpo-peinh.
ENDIF.
Calcul quantité réceptionnée.
itb_pca-wemng = itb_pca-wemng + itb_eket-wemng.
Calcul du retard en nombre de jours calendaires
Le calcul du retard ne doit pas prendre en compte
le jour de livraison
ADD 1 TO itb_eket-eindt.
IF NOT itb_pca-attdu IS INITIAL
AND itb_eket-eindt LT sy-datum.
Calcul du retard en nombre de jours ouvrés
CLEAR w_retard.
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_PERIOD'
EXPORTING
date_deb = itb_eket-eindt
date_fin = sy-datum
IMPORTING
jours = w_retard.
itb_pca-rtard = itb_pca-rtard + w_retard .
ENDIF.
ELSEIF itb_eket-ebeln > itb_ekpo-ebeln
OR ( itb_eket-ebeln = itb_ekpo-ebeln
AND itb_eket-ebelp > itb_ekpo-ebelp ).
w_index_eket = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
Recherche de la derniere date de livraison.
LOOP AT itb_mseg
FROM w_index_mseg.
IF itb_mseg-ebeln = itb_ekpo-ebeln
AND itb_mseg-ebelp = itb_ekpo-ebelp.
READ TABLE itb_mkpf
WITH KEY mblnr = itb_mseg-mblnr
mjahr = itb_mseg-mjahr
BINARY SEARCH.
IF sy-subrc = 0.
IF itb_mkpf-bldat > itb_pca-bldat.
itb_pca-bldat = itb_mkpf-bldat.
ENDIF.
ENDIF.
ELSEIF itb_mseg-ebeln > itb_ekpo-ebeln
OR ( itb_mseg-ebeln = itb_ekpo-ebeln
AND itb_mseg-ebelp > itb_ekpo-ebelp ).
w_index_mseg = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
APPEND itb_pca.
CLEAR itb_pca.
FAE26446 suppression parag. suivant
ELSEIF itb_ekpo-ebeln > itb_ekko-ebeln.
w_index_ekpo = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
Fin FAE26446
ENDLOOP.
=========================
PREVISIONS DE COMMANDES *
=========================
SORT itb_eord BY matnr werks lifnr ekgrp.
SORT itb_eban BY matnr werks flief ekgrp.
SORT itb_plaf BY matnr plwrk flief.
SORT itb_z03_bw_cmp1 BY matnr werks.
SORT itb_z03_bw_cmp2 BY matnr werks."+DE3K937051
SORT itb_pca BY matnr werks lifnr.
w_index_eban = 1.
w_index_plaf = 1.
w_index_z03_bw_cmp1 = 1.
w_index_pca = 1.
w_index_z03_bw_cmp2 = 1."+DE3K937051
Remplissage de la table des prévisions de commande.
LOOP AT itb_eord.
CLEAR: str_prev_pfc,
w_trouve.
MOVE-CORRESPONDING itb_eord TO str_index1.
MOVE-CORRESPONDING itb_eord TO str_index3_eord.
MOVE-CORRESPONDING itb_eord TO itb_prev_cde.
Recherche dans table division/article (MARC) afin de déterminer si
article PFS (prod fabriqué à stock) ou PFC (Prod fabriqué sur cde)
AT NEW werks.
READ TABLE itb_marc_eord
WITH KEY matnr = itb_eord-matnr
werks = itb_eord-werks
BINARY SEARCH.
IF sy-subrc NE 0.
CLEAR itb_marc_eord.
ENDIF.
ENDAT.
a - Prévisions pour les PFS : DA + OP *
*Calcul des quantités de commande.
IF itb_eord-disls = text-tl1.
itb_prev_cde-bstmi = itb_eord-bstfe.
ELSEIF itb_eord-disls = text-tl2
OR itb_eord-disls = text-tl3.
IF itb_eord-bstrf NE 0
AND itb_eord-bstmi = 0
AND itb_eord-bstma = 0.
itb_prev_cde-bstmi = itb_eord-bstrf.
ELSEIF itb_eord-bstrf NE 0
AND itb_eord-bstmi NE 0.
itb_prev_cde-bstmi = itb_eord-bstmi.
ELSEIF itb_eord-bstrf = itb_eord-bstma
AND itb_eord-bstrf NE 0
AND itb_eord-bstmi = 0.
itb_prev_cde-bstmi = itb_eord-bstma.
ENDIF.
ENDIF.
si article PFS (Prod fabriqué à stock) recherche des
demandes d'achat ou ordres planfiés
IF itb_marc_eord-strgr IN r_type_pfs.
Récupérat° calendrier de la division pour calcul correct lors de
l'ajout de eban-webaz ou plaf-webaz jours ouvrés
CLEAR w_trouve_pfs ."+DE3K937051
READ TABLE itb_t001w
WITH KEY werks = itb_eord-werks
BINARY SEARCH.
IF sy-subrc = 0.
LOOP AT itb_eban
FROM w_index_eban.
MOVE-CORRESPONDING itb_eban TO str_index2.
IF str_index1 = str_index2.
w_trouve_pfs = 'X'."+DE3K937051
si qte commandées pour la DA < quantité de la DA
IF itb_eban-bsmng < itb_eban-menge.
ajout de quantité de la DA - qte commandée pour la DA
PERFORM affect_da.
ENDIF.
ELSEIF str_index2 > str_index1.
w_index_eban = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
ENDIF.
ajout des quantité des OP (ordres planifiés)
LOOP AT itb_plaf
FROM w_index_plaf.
MOVE-CORRESPONDING itb_plaf TO str_index4.
str_index4-werks = itb_plaf-plwrk.
str_index4-lifnr = itb_plaf-flief.
IF str_index4 = str_index3_eord.
Ajout de webaz jours ouvrés à pedtr
CALL FUNCTION 'Z_03_MM_ADD_TO_FACTORYDATE'
EXPORTING
i_date = itb_plaf-pedtr
i_calendar_id = itb_t001w-fabkl
i_nb_days = itb_plaf-webaz
IMPORTING
o_date = w_dat_op
EXCEPTIONS
conv_error = 1
OTHERS = 2.
IF sy-subrc
If forecasts found in Z03_BW_CMP2 for the article
IF w_trouve_pfs = 'X'."-DE3K937602
Recalculation prev month M in fct of Nb of wrought days of the month
IF NOT itb_prev_cde-men00 IS INITIAL.
one does not hold any more account of the day in progress
w_lendemain = w_date0 + 1.
CLEAR:w_nb_j,w_nb_j_tot. "DE3K938206+
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_PERIOD'
EXPORTING
date_deb = w_lendemain
date_fin = w_fin_mois
IMPORTING
jours = w_nb_j.
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_MONTH'
EXPORTING
date = w_lendemain
IMPORTING
jours = w_nb_j_tot.
itb_prev_cde-men00 = itb_prev_cde-men00 * w_nb_j / w_nb_j_tot
*CLA DE3K925301 FAE27197
*to round has the higher entirety
itb_prev_cde-men00 = ceil( itb_prev_cde-men00 ). "DE3K938206-
ENDIF.
ENDIF."-DE3K937602
*End change BNI
b - Prévisions pour les PFC (Z03_BW_CMP1 puis rééquilibrage) *
Recherche des previsions dans Z03_BW_CMP1
si article PFC (Prod fabriqué sur cde) recherche des prévisions
IF NOT itb_marc_eord-strgr IN r_type_pfs.
CLEAR str_prev_pfc.
MOVE-CORRESPONDING itb_eord TO str_prev_pfc.
CLEAR w_trouve_pfc .
LOOP AT itb_z03_bw_cmp1
FROM w_index_z03_bw_cmp1.
MOVE-CORRESPONDING itb_z03_bw_cmp1 TO str_index7.
MOVE-CORRESPONDING itb_eord TO str_index6.
IF str_index6 = str_index7.
si on trouve des prévisions dans z03_bw_cmp1 pour la source
d'appro eord alors c'est un article PFC
w_trouve_pfc = 'X'.
CASE itb_z03_bw_cmp1-pdatu+0(6).
WHEN w_date0+0(6).
str_prev_pfc-men00 = itb_z03_bw_cmp1-plnmg.
WHEN w_date1+0(6).
str_prev_pfc-men01 = itb_z03_bw_cmp1-plnmg.
WHEN w_date2+0(6).
str_prev_pfc-men02 = itb_z03_bw_cmp1-plnmg.
WHEN w_date3+0(6).
str_prev_pfc-men03 = itb_z03_bw_cmp1-plnmg.
WHEN w_date4+0(6).
str_prev_pfc-men04 = itb_z03_bw_cmp1-plnmg.
WHEN w_date5+0(6).
str_prev_pfc-men05 = itb_z03_bw_cmp1-plnmg.
WHEN w_date6+0(6).
str_prev_pfc-men06 = itb_z03_bw_cmp1-plnmg.
WHEN OTHERS.
ENDCASE.
ELSEIF str_index7 > str_index6.
w_index_z03_bw_cmp1 = sy-tabix.
EXIT.
ENDIF.
ENDLOOP.
*Begin change BNI
Si des prévisions trouvées dans Z03_BW_CMP1 pour l'article
IF w_trouve_pfc = 'X'.
Recalcul prev mois M en fct du nb de jours ouvrés du mois
IF NOT str_prev_pfc-men00 IS INITIAL.
on ne tient plus compte du jour en cours
w_lendemain = w_date0 + 1.
CLEAR:w_nb_j,w_nb_j_tot. "DE3K938206+
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_PERIOD'
EXPORTING
date_deb = w_lendemain
date_fin = w_fin_mois
IMPORTING
jours = w_nb_j.
CALL FUNCTION 'Z_00_BC_WORKDAYS_PER_MONTH'
EXPORTING
date = w_lendemain
IMPORTING
jours = w_nb_j_tot.
str_prev_pfc-men00 = str_prev_pfc-men00 * w_nb_j / w_nb_j_tot.
*CLA DE3K925301 FAE27197
*arrondir a l'entier supèrieur
str_prev_pfc-men00 = ceil( str_prev_pfc-men00 ).
ENDIF.
Equilibrage PFC : commande/prévision du mois
Recherche COMMANDES cumulées pour M à M+6
CLEAR str_pca_pfc.
LOOP AT itb_pca
FROM w_index_pca.
MOVE-CORRESPONDING itb_pca TO str_index5.
IF str_index5 = str_index3_eord.
IF NOT itb_pca-menge IS INITIAL.
CASE itb_pca-eindt+0(6).
WHEN w_date0+0(6).
IF itb_pca-eindt >= w_date0.
str_pca_pfc-men00 = str_pca_pfc-men00 + itb_pca-menge.
ENDIF.
WHEN w_date1+0(6).
str_pca_pfc-men01 = str_pca_pfc-men01 + itb_pca-menge.
WHEN w_date2+0(6).
str_pca_pfc-men02 = str_pca_pfc-men02 + itb_pca-menge.
WHEN w_date3+0(6).
str_pca_pfc-men03 = str_pca_pfc-men03 + itb_pca-menge.
WHEN w_date4+0(6).
str_pca_pfc-men04 = str_pca_pfc-men04 + itb_pca-menge.
WHEN w_date5+0(6).
str_pca_pfc-men05 = str_pca_pfc-men05 + itb_pca-menge.
WHEN w_date6+0(6).
str_pca_pfc-men06 = str_pca_pfc-men06 + itb_pca-menge.
ENDCASE.
ENDIF."NOT itb_pca-menge IS INITIAL
ELSEIF str_index5 > str_index3_eord.
w_index_pca = sy-tabix.
EXIT.
ENDIF.
ENDLOOP."itb_pca
*. Equilibrer commande / prévision des mois : diminuer la quantité de
prévision de chaque mois par le portefeuille de commande client du
mois*. Si ce solde est négatif alors lui donner la valeur 0.
w_i = 0.
Ajustement commandes/prévisions pour les mois M à M+6
WHILE w_i .
Pour un mois, SI Prévisions > Commandes en cours
IF .
Prévisions = Prévisions - Commandes en cours
= 0.
ENDIF.
On passe au mois suivant
w_i = w_i + 1.
ENDWHILE.
MOVE str_prev_pfc-men00 TO itb_prev_cde-men00.
MOVE str_prev_pfc-men01 TO itb_prev_cde-men01.
MOVE str_prev_pfc-men02 TO itb_prev_cde-men02.
MOVE str_prev_pfc-men03 TO itb_prev_cde-men03.
MOVE str_prev_pfc-men04 TO itb_prev_cde-men04.
MOVE str_prev_pfc-men05 TO itb_prev_cde-men05.
MOVE str_prev_pfc-men06 TO itb_prev_cde-men06.
ENDIF. "w_trouve_pfc = 'X'.
ENDIF.
*recherche du libellé articleHi,
see this link, useful tips, links and transactions for best performance, by Anji.
https://forums.sdn.sap.com/click.jspa?searchID=5967263&messageID=4260111
Regards -
Tutorial: How To Improve YouTube Playback on iBook G3 (Dual USB)
Disclaimer: Apple does not necessarily endorse any suggestions, solutions, or third-party software products that may be mentioned in the topic below. Apple encourages you to first seek a solution at Apple Support. The following links are provided as is, with no guarantee of the effectiveness or reliability of the information. Apple does not guarantee that these links will be maintained or functional at any given time. Use the information below at your own discretion.
This is a brief tutorial on how to improve YouTube video playback on an Apple iBook G3. As of now, I have only tested this method on my own iBook. iBook's with lower specs than the 900 MHz model may not receive the same performance upgrade from this brief tutorial. With that said, here is what you can do to attempt to make YouTube more functional on your iBook G3.
1) If the iBook is running Mac OS X 10.4 (Tiger), disable Dashboard and Spotlight:
While widgets are fun and Spotlight is a useful quick search tool, they are known resource consumers that make video playback problematic for older Mac laptops, such as the iBook G3. To accomplish this, you will have to use the Terminal. Once the Terminal is open, enter the following command
{color:purple}defaults write com.apple.dashboard mcx-disabled -boolean YES{color}
After entering this command, you will then need to restart the Dock (Dashboard is owned by the Dock). To do so, again, using the Terminal, you will enter the following command.
{color:purple}killall Dock{color}
You may still see the Dashboard icon in the Dock, but clicking on it should do nothing.
For the next part, you will use the Terminal to disable Spotlight. Open the Terminal and enter the following command.
{color:purple}sudo nano /etc/hostconfig{color}
This will bring up a configuration listing. Use the arrow keys to scroll down and change the value, SPOTLIGHT=-YES-, to SPOTLIGHT=-NO-.
From here, you should press Ctrl+X to exit, upon which it will ask if you want to save. Follow the on screen prompts to save, and exit out of the Terminal. Spotlight will still appear in the corner of your screen, but it won't search for anything. Now on to the next step.
2) For any video URL on YouTube, add &fmt=5 to the end of the URL, and this will force videos to run in quarter VGA mode (320x240). The video quality will be degraded, but you should maintain a stable frame rate that is uninterrupted and capable of streaming without the need to pause and wait for the entire video to load.
This method has worked for me for old and new videos alike. Unfortunately, I have not found a way to make iTunes/Quicktime force videos into a low resolution mode, so this fix will only resolve video playback involving YouTube.
*To restore functionality to Dashboard and Spotlight:*
1) How to Restore the Dashboard
Open the terminal and input the following command
{color:purple}defaults write com.apple.dashboard mcx-disabled -boolean NO {color}
After entering this command, you will have to restart the Dock. To do so, enter the following command into the terminal
{color:purple}killall Dock{color}
Now, can drag the Dashboard icon back to the Dock, or if you did not remove it to begin with, it should function once again.
2) How to restore Spotlight
Open the terminal and enter the following command
{color:purple}sudo nano /etc/hostconfig{color}
This will open up a config file. Scroll down (using the arrow keys) to the portion that says SPOTLIGHT=-NO- and change the value so that it says SPOTLIGHT=-YES-
Exit the config file by pressing Ctrl+X. Follow the onscreen prompts to save the config file, and you are allset.
Best of luck to you all. I hope that this tutorial has been helpful.
This is the 2nd version of this tip. It was submitted on May 19, 2010 by Macology, with thanks to Ronda Wilson.
Do you want to provide feedback on this User Contributed Tip or contribute your own? If you have achieved Level 2 status, visit the User Tips Library Contributions forum for more information.Disclaimer: Apple does not necessarily endorse any suggestions, solutions, or third-party software products that may be mentioned in the topic below. Apple encourages you to first seek a solution at Apple Support. The following links are provided as is, with no guarantee of the effectiveness or reliability of the information. Apple does not guarantee that these links will be maintained or functional at any given time. Use the information below at your own discretion.
This is a brief tutorial on how to improve YouTube video playback on an Apple iBook G3. As of now, I have only tested this method on my own iBook. iBook's with lower specs than the 900 MHz model may not receive the same performance upgrade from this brief tutorial. With that said, here is what you can do to attempt to make YouTube more functional on your iBook G3.
1) If the iBook is running Mac OS X 10.4 (Tiger), disable Dashboard and Spotlight:
While widgets are fun and Spotlight is a useful quick search tool, they are known resource consumers that make video playback problematic for older Mac laptops, such as the iBook G3. To accomplish this, you will have to use the Terminal. Once the Terminal is open, enter the following command
{color:purple}defaults write com.apple.dashboard mcx-disabled -boolean YES{color}
After entering this command, you will then need to restart the Dock (Dashboard is owned by the Dock). To do so, again, using the Terminal, you will enter the following command.
{color:purple}killall Dock{color}
You may still see the Dashboard icon in the Dock, but clicking on it should do nothing.
For the next part, you will use the Terminal to disable Spotlight. Open the Terminal and enter the following command.
{color:purple}sudo nano /etc/hostconfig{color}
This will bring up a configuration listing. Use the arrow keys to scroll down and change the value, SPOTLIGHT=-YES-, to SPOTLIGHT=-NO-.
From here, you should press Ctrl+X to exit, upon which it will ask if you want to save. Follow the on screen prompts to save, and exit out of the Terminal. Spotlight will still appear in the corner of your screen, but it won't search for anything. Now on to the next step.
2) For any video URL on YouTube, add &fmt=5 to the end of the URL, and this will force videos to run in quarter VGA mode (320x240). The video quality will be degraded, but you should maintain a stable frame rate that is uninterrupted and capable of streaming without the need to pause and wait for the entire video to load.
This method has worked for me for old and new videos alike. Unfortunately, I have not found a way to make iTunes/Quicktime force videos into a low resolution mode, so this fix will only resolve video playback involving YouTube.
*To restore functionality to Dashboard and Spotlight:*
1) How to Restore the Dashboard
Open the terminal and input the following command
{color:purple}defaults write com.apple.dashboard mcx-disabled -boolean NO {color}
After entering this command, you will have to restart the Dock. To do so, enter the following command into the terminal
{color:purple}killall Dock{color}
Now, can drag the Dashboard icon back to the Dock, or if you did not remove it to begin with, it should function once again.
2) How to restore Spotlight
Open the terminal and enter the following command
{color:purple}sudo nano /etc/hostconfig{color}
This will open up a config file. Scroll down (using the arrow keys) to the portion that says SPOTLIGHT=-NO- and change the value so that it says SPOTLIGHT=-YES-
Exit the config file by pressing Ctrl+X. Follow the onscreen prompts to save the config file, and you are allset.
Best of luck to you all. I hope that this tutorial has been helpful.
This is the 2nd version of this tip. It was submitted on May 19, 2010 by Macology, with thanks to Ronda Wilson.
Do you want to provide feedback on this User Contributed Tip or contribute your own? If you have achieved Level 2 status, visit the User Tips Library Contributions forum for more information. -
Tutorial: How To Improve Youtube Playback on iBook G3
Salutations,
this is a brief tutorial on how to improve Youtube video playback on an Apple iBook G3. As of now, I have only tested this method on my own iBook. iBook's with lower specs may not receive the same performance upgrade from this brief tutorial. With that said, here is what you can do to make Youtube functional on your iBook G3.
1) Disable Dashboard and Spotlight:
While widgets are fun and Spotlight is a useful quick search tool, they are known resource consumers that make video playback problematic for older Mac laptops, such as the iBook G3. To accomplish this, you will have to use the terminal. Once the terminal is open, enter the following command
defaults write com.apple.dashboard mcx-disabled -boolean YES
After entering this command, you will then need to restart the Dock (Dashbaord is owned by the Dock). To do so, again, using the terminal, you will enter the following command.
killall Dock
You may still see the Dashboard icon in the Dock, but clicking on it should do nothing.
For the next part, you will use the terminal to disable Spotlight. Open the terminal and enter the following command.
sudo nano /etc/hostconfig
This will bring up a configuration listing. Use the arrow keys to scroll down and change the value, SPOTLIGHT=-YES-, to SPOTLIGHT=-NO-.
From here, you should press Ctrl+X to exit, upon which it will ask if you want to save. Follow the on screen prompts to save, and exit out of the terminal. Spotlight will still appear in the corner of your screen, but it won't search for anything. Now on to the next step.
2) For any video URL on Youtube, add &fmt=5 to the end of the URL, and this will force videos to run in quarter VGA mode (320x240). The video quality will be degraded, but you should maintain a stable frame rate that is uninterrupted and capable of streaming without the need to pause and wait for the entire video to load.
This method has worked for me for old and new videos alike. Unfortunately, I have not found a way to make iTunes/Quicktime force videos into a low resolution mode, so this fix will only resolve video playback involving Youtube. Best of luck to you all. I hope that this tutorial has been helpful.Others have suggested that you may want to tell users how to revert to the original settings.
I'm working on getting this posted as a User Tip. Would you like to add instructions on how to regain Dashboard and Spotlight functionality? -
How to increase scan rate of NI Switch SCXI 1130
Hi,
I have NI PCI 4070 DMM used with NI SCXI 1130 sitch module. I have connected 10 thermocouples to 1130 module. I am scanning the channels and reading the values in the program using niSwitch and niDMM VIs. I am using software trigger in the program. I have configured Software Trigger in niDMM configur trigger and niDMM configure Multipoint. I get the correct values when i scan using chi->com0, where i goes from 0 to 9. But the problem is that the rate of scanning is very slow.
There is niSwitch Configure scan Rate.vi, here i have given scan delay as 0 second.
It takes one second for one channel when i run the program. why is this , is this because i used software trigger for each channel scan? how to improve the scan rate. ?Sorry for the confusion, I started writing a post and got interrupted and came back to it too late. You can disregard the last post and here is my final answer:
I would actually recommend that you use synchronous scanning if you want to maximize the speed of your scan, rather than using software triggers. If you use synchronous scanning, the DMM will generate a digital pulse (Measurement Complete) each time it completes a measurement, allowing the switch to advance to the next entry in the scan list the instant the DMM has completed its measurement. The DMM will then take the next meausurement after a specified harware-timed interval. This will be much more efficient than sending software triggers back and forth to time the scanning. To set up your application using synchronous scanning, follow these steps:
Open the LabVIEW shipping example "niSwitch DMM Switch Synchronous Scanning.vi", found in the NI Example Finder in the folder Hardware Input and Output » Modular Instruments » NI-SWITCH (Switches).
Physically connect the Measurement Complete output trigger from the DMM to the trigger input of the switch. How you will do this depends on what type of chassis you are using (PXI/SCXI combo chassis or separate chassis) and what switch terminal block you're using. If you need assistance with this please provide more details about your hardware setup and I'd be happy to help out. The following resource may be helpful here: KnowledgeBase 3V07KP2W: Switch/DMM Hardware Configurations.
Select valid values for all other front panel controls and run the VI.
I hope this is helpful. Please let me know if I have misunderstood your application, or if you would like me to go into more detail on any specific part of the solution provided above. -
Ask The Experts How to Improve Your PC's Performance on June 1st at 3:30 pm PDT
Learn how to improve your PC 's performance on June 1st from 3:30 -4:30 pm PDT. We'll have a team of experts available to answer your questions.
When it comes to performance, your PC is similar to your car. Both need to be cared for to keep them running run well. But unlike your car, you don’t need to bring your PC into a shop for a tune up. You can easily do it yourself if you know the right steps to take. Our experts will answer your questions and provide tips on how to make your PC run better. Topics that may be covered in this real-time chat event include the following:
How to customize your PC to increase performance;
How to prolong your notebook’s battery life;
How to choose the right video card, power supply, or add the right amount of memory; or
How to use the tools built into your PC that can make it run better and fix common problems.
While you can attend this real-time chat event without signing up in advance, you must be a member of the HP Support Forums to ask questions. Signing up is easy and only takes a few moments, plus it will allow you to post questions or give answers on the Forums.
And it is all free!
So, come and learn how to get the most out of your PC. Please be sure to come on time as space is limited!
Message Edited by timhsu on 05-12-2009 05:33 PM
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.
This question was solved.
View Solution.Here is the transcript of the chat event on improving PC performance.
Please note that I have altered the transcript so that follow up questions are included in the logical order.
I am in the process of planning the next chat event. I would love to hear what topics would interest you, what day of the week and time is best for you, and if you think an hour is too long.
So, if you get a minute, please let me know.
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.
Maybe you are looking for
-
I would like to get the 3.6 version and uninstall the 4.0 version computer running slow
-
HELP - iMac can't find system file for start-up
Hi, My Rev. B iMac (running OS 9.2) suddenly can't find the system file. I was working in MS Word for Mac when the system crashed. Upon start-up the computer couldn't find the system and showed a flashing question mark in an old floppy disk icon. I s
-
My brand new Lumia 620's loudspeaker produces a hissing sound whenever an audio clip is played. This can be noticed at the end of the screen lock sound as well as in the background of every single music track The hiss's intensity does not change when
-
Error: -3, tried registry "classes" fix, now get 1402 Could not open key
I tried to upgrade itunes and I get an error when quicktime installs. The error is: Error: -3, followed by itunes cannot run because some of its required files are missing. I followed the registry "classes" permission fix and tried to install a stand
-
Error in viewing the Vanilla Reprots
Hi All, I have installed OBIEE 11g and top of it i have installed OBIA 7.9.6.3 in my local machine. I got the Vanilla RPD (OracleBIAnalyticsApps) and catalog as part of the OBIA installation. When i try to open a existing report in the Presentation S