How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

Hello
I'm looking for information on how to install 2 newly purchased cards and keep running into dead links. The cards I bought are for a CISCO-2801-CCME/K9 with PVDM2-8, FL-CCME-25, SP Services 128F/256D cisco router:
vic3 2fxs/DID and a vic2 2fxo.
I keep finding documents on how to install these cards but all links are dead and leading to nowhere.
http://www.cisco.com/en/US/docs/routers/access/interfaces/ic/hardware/installation/guide/2port_FXS_DID_VIC.html#wp1065062
The 2 documents i'm looking for are: how to install a 2-port vic2 fxo cards on cisco 2801 router and how to install 2-port vic3 2fxs/DID cards on the same 2801 cisco router.
NOTE: I've never installed these cards and am not sure if:
Does my ios support both of these cards?
and which slots do I install those in the router.
I have 4 slots like this:
slot 0: This slot only accepts VIC's ***This could be used for the vic3 2fxs/DID card correct?
slot 1: Nothing written here ****What can i install in this slot?
slot 2: This slot only accepts VIC's and WIC's ***If I buy a WIC and install here which other slot can i install my VIC2-2FXO card in ?
slot 3: Nothing written here ***What can i install in this slot?
Any chance someone can help me out with this.
Thanks very much

Ok
I was able to figure out what goes where and found out that the IOS i had c-2801-spservicesk9-mz.124-15.T10.bin with cme-full-4.1.0.2 tar didn't support the vic3 2fxs/DID card. I then found the one that works which is the c2801-spservicesk9-mz.124-22.YB5.bin.I am now able to see my new hardware interfaces. The question I have now is since the previous version ran with cme-full-4.1.0.2 tar i'm not sure if this needs to be changed since in the compatibility matrix i found this IOS c2801-spservicesk9-mz.124-22.YB5.bin to be compatible with cme-full-7.1.0.0 tar
Do i need to remove cme-full-4.1.0.2 tar and install the cme-full-7.1.0.0 tar?
If yes, i know how to install the cme-full-7.1.0.0 tar but how do i remove the other cme-full-4.1.0.2 tar file in order to be able to install the other version?
Thanks

Similar Messages

Vic3-2FXS/DID fax problem

I have a network in Beijing China below,
(1) E1 Pri interface to PSTN
(2) Vic3-2FXS/DID to fax machine
all these modules installed on Cisco 2900, when I call my fax machine from PSTN, the fax machine answered, but fax can't start.
I want to know is there any special consideration about the fax configuration to be worked.
Thanks for your advice.
Robert
2011/2/18

Hey Robert.
Since you have PRI and the fxs port on the same card, in theory there is not a whole lot you need to do with regards to the fax or port configuration on the router if this is H323 or SIP. On our initial voip gateways even on port to port calls we would invoke fax relay, but on the ISR line with the internal tdm backplane, the dsp should be dropped from the call with minimal impairment of the connection through the gateway.
Now, this is true as long as you don't have "no local-bypass' configured under the voice-card. Default is that this is not configured but it you do, you should change it to local-bypass. "show voice dsp active" will show if the dsp is still in the loop on the call as well.
Definitely check the E1 controller ("show controller e1") for slips and errors. This will kill a fax if present.
Looking back at your previous post though, I would not expect you to be seeing G722 on the output of the show voice call summary when the call connects between the two ports.
Are you using MGCP?
When the call is active between the two ports, what is the output of "show call active voice brief" and "show call active fax brief"?
There are a few good resources for troubleshooting fax issues. An excellent source if the CiscoPress publication "Fax, Modem and Text for IP Telephony". If you would like some of the scaled down versions, I have posted a couple of links that would be useful.
Bryan
https://supportforums.cisco.com/community/netpro/collaboration-voice-video/ip-telephony/blog/2010/10/26/fax-configuration-and-troubleshooting-project
http://www.cisco.com/en/US/docs/ios/12_3/vvf_c/voice_troubleshooting/old/vts_fax.html

VIC3-2FXS/DID VS VIC3-2FXS-E/DID

hi all,
we'll upgrade our router from 2811 to 2911.
the current 2811 uses VIC2-2FXS but saw on cisco's website that we need a VIC3 instead.
i saw there's two versions of this card, the other has an 'E'.
what's the difference between the two? can i just get a VIC3-2FXS/DID?

Hi John,
The difference is explained in the following link
http://www.cisco.com/c/en/us/products/collateral/interfaces-modules/ip-communications-voice-fax-network-modules/product_data_sheet0900aecd801c595e.html
VIC3-2FXS-E/DID is designated as an "Off-Premise Extension Lite" product offering. This means that while the module addresses a subset of the off-premise extension applications, it should be noted that the module is not in full compliance for off-premise usage.
HTH
Manish

VIC3-2FXS/DID

Hi everybody,
We have a CCM version 4.x and we need to connect two fax extensions on a VIC3-2FXS/DID card.
The problem is that the faxs are 6 floors up the CCM. Between floors are connected by Optical fiber thought Cisco Switchs. We can configure these faxs on that card?
Thanks!!

VIC3-2FXS/DID
If you have copper pairs to connect, yes.<-- means that if we connect the faxs to a switch and the VIC3-2FXS/DID to the other switch with Ethernet cable it will work?
VIC3-2FXS/DID

How to install leopard again after formating hd and now it just allows me to download yosemite.

how to install leopard again after formating hd and now it just allows me to download yosemite. When i insert the original cd of leopard it doesnt restart from it!!!
I made a mistake formating hd without creating a bootable disk... So i started the process to install yosemite, then i formated the hd and forgot that the installer was no more in applications because no more applications forlder!!! after the format it just allows me to install directly from app store which is taking 18 hours to download.
I tried to restart with original leopard cd but it didnt recognize it and jump back to yosemite install from app store..
What should i do?
Can anyone help me please? thanks

How did you even manage to start installing Yosemite? What operating system did you have before you upgraded? It wasn't Leopard, since you need Snow Leopard (10.6) to get to the App Store.
Matt

How to install Tamil fonts to my iPad and iPhone?

How to install Tamil fonts to my iPad and iPhone?

ebenezeramos wrote:
How to install Tamil fonts to my iPad and iPhone?
Your iPad and iPhone should already have Tamil fonts. Can you really not see a web page like this one?
http://ta.wikipedia.org/
There is however no keyboard yet. If that is what you are talking about, search the app store for "tamil" to see if there is a keyboard app which might be useful for some purposes. Also try the Keyman app.
You can ask Apple for a Tamil keyboard via
http://www.apple.com/feedback

HT4407 i have hp laptop 64bit , now i would like to install mac os on my laptop so plz help me how to install mac os in my laptop and how do i get mac os ?

i have hp laptop 64bit , now i would like to install mac os on my laptop so plz help me how to install mac os in my laptop and how do i get mac os ?

There is no way to accomplish that.
Buy a Mac.

How to install E-business suite for easy and simple?

Please help me.
I installed oracle application 11i,but i don,t use it. when i create a new user or modify a user,then login in system with this user name,but it is failed.the error message is :
ORA-01403:not found data.
ORA-06510:
ORA-01403: Traslation data has not been installed yet,pleas apply NLS patch.
who tell me:how to get NLS pacth?where get NLS patch?

LAVANKV wrote:
Hi All,
Can any body direct me how to install e business suite on linux 32 bit env.
Thanks.Interesting Documents Concerning E-Business Suite 11i to R12 Upgrades [ID 850008.1]
Oracle E-Business Suite Installation Guide Using Rapid Install
http://docs.oracle.com/cd/E18727_01/doc.121/e12842/toc.htm
Thanks,
Hussein

How to install Laserjet M1217 for both wireless and network

How to install an HP Laserjet Pro M1217nfw MFP on an XP system for both network and wireless capabilities?

Hi,
Are you talking about a mixture of wired and wireless ? If yes, please check your existing hardware and use the following manual to select one connection type then post back if having any porblem during the setup:
http://h10032.www1.hp.com/ctg/Manual/c00389927.pdf
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

How to install Photoshop CS2 on new computer, and deinstall from old one.

I have Photoshop CS2 installed on my desktop since 2005. I now want to install it on a new desktop and remove it from the old desktop.
But does that still work since this is an old version? Who can help me?

CS2 activation is no longer supported. Go here for a non-activation copy and new serial number.
Download Acrobat 7 and CS2 products
Gene

Why the ringing voltage closely 0v for VIC3-2FXS/DID port?

Initially, I have tested every port of FXS module on ISR with an analog phone. There
was ringing tone and I was able to communicate to other as normal. The second
test involved measuring the ringing voltage on the same ports by using a pair cable and multimeter. The
'idle voltage' measured was around 44V and when there was an incoming call, the measured 'ringing
voltage' was close to 0V.
So why the ringing voltage is drop to 0V?
Please advice.

You cannot measure ringing voltage with a common multimeter. Read why:
http://www.sandman.com/ringvoltbul.html

I did factory install on my hp probook 4520s and usb ports worked

did factory instasll usb ports worked after restarting it saids usb ports cannot start in deviice mangager

You should really read the manual.
"How do you restore from backup? "
Restore. When given the choice, choose to use backup.
"And how can I check to see if the pics and videos are on my computer somewhere first??"
They would only be where you put them. What program did you use to import them? Pics/vids taken with ipod are not part of the sync process at all. You should be importing them just as you would with any digital camera.
If you did not import them, then they are not on your computer.

Installed Windows & 32 Bit But Drivers and USB ports NOT WORKING.

I bugh an HP Pavillion TS 14 Notebook that came preinstall with Windows 8.1 64 bit which I hate so wiped the drives and installed Windows 7 32 bit and now I have a big problem. None of my network drivers work and the 2 uSB ports where I plug my mouse and other SB hardware in no longer work.
I did a back up of the SW Set up file that has all of the HP dvers for my laptop but both the network and video divers won't install. And When I try to install the drives I get the eror message saying they are not compatible with this version of Windows.
I have loked on the HP website under my laptop model which s as above but HP don't do drivers for Windows 7 32 for my laptop. And I have looked on both the Realteck website for both the Realteck ethnet and Realteck wireless network drivers but none of them work or install on my operating system. The video drivers Intel don't work either. So I am really stuck a I cannot go back to Windows 8.1 as though that 32 bit Windows 7 would work on my laptop but most of my drivers are not compatible with the operating sytem And I don't want to install 64 bit Windows as I like 32 bit.
The drivers that are not working on Windows 7 32 bit are:
Realteck RTL8188EE 802-11b/gn witeless lan
Realteck ethnet die and
Intel High definition graphcs driver
Which don't work at all on Windows 7 32 bit as they are 64 bit only drivers.
So can you please post me a link bth the network and Intel graphics drvers that work with my laptop. As I have tried lots of different Realteck and raphics drivers for Window 7 but NONE of them work on my system. And None of my USB ports are working either. So how do I solve this problem?
This question was solved.
View Solution.

Hi:
Should be no problem to get W7 32 bit to work on that model.
Just use all of the drivers and software from the HP Probook 450 G0 on your model except the Audio, BIOS and firmware files.
Your model uses the Intel HD graphics driver only.
The first driver you have to install is the Intel chipset installation utility and then reboot.
http://h20565.www2.hp.com/portal/site/hpsc/public/psi/swdHome/?cc=us&lang=en&sp4ts.oid=5359407&ac.ad...
Audio: Accept the agreement. Download and install the first driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=24&Level=4&Conn=3&DownT...
If for some reason, the Intel HD graphics driver from that model does not work, then use this one...
https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=23713

How to install the driver of the 'SCSI and RAID Host Controller'

Hi,
I have two Windows XP(32Bit) installations:
•Windows XP SP2(32Bit) which is old and it seems as if it is infected by some viruses.
•I have installed another fresh clean Windows XP(32Bit) SP3. However, I have found that there is no category named with ''SCSI and RAID Host Controller'. However, when checking out the old version of Windows XP, I found 'SCSI and RAID Host Controller'
is there. (Screen shot below)
The new Windows XP(32Bit) SP3, there is no 'SCSI and RAID Host Controller'
My motherboard is:
My Desktop Computer(Intel P 4, 512MB of RAM, and Graphics Card with 256MB of RAM.
]I am seeing that most computer doesn't has the scsi / raid controller . in the old Windows XP on my computer that SCSI and RAID controller exists, and it it has not a yellow mark on it.
When I installed a new windwos XP 32Bit SP3, no SCSI/RAID in divice manager .
My computer sound on new Windows XP doesn't work , however, on old Windows XP SP2 works well. I have a buitl-in sound card. SCSI and RAID controller category in the device manager on the old Windows xp SP2 is realted to sound card,I don't think.
Thus, What drivers would let the 'SCSI and RAID Host Controller' added in the device manager?
A man should convert his anger and sadness into strength to continue living in this life.

If you open the case and shine a light on the motherboard you can usually see both the manufacturers name and the model printed on the pcb somewhere. You should also normally see this information on the first POST screen when you turn on the PC.
Otherwise Google "775i65G" like I did.
Here are the driver downloads (assuming it is an Asrock 775i65G R2.0 and not an R3.0)
http://www.asrock.com/mb/Intel/775i65G%20R2.0/?cat=Download&os=XP
You should install the inf driver first. Hopefully after you do that you will see your desired listing in Device Manager.
With regard to the AMR driver and the HDMR driver, you can find some information about these here :
http://en.wikipedia.org/wiki/Audio/modem_riser
Unless you actually have something plugged into these risers, it is probably not necessary to install the drivers.
However, the drivers for the integrated C-Media audio chip and the Realtek Lan chip may prove useful.
It looks like the motherboard has integrated video but if you are using a graphics card it will not normally be necessary to install the VGA driver.
You can download both the manual and the installation guide here
http://www.asrock.com/mb/Intel/775i65G/?cat=Manual
And if "SCSI and RAID Host Controller" is still not shown in Device Manager, don't worry - because these functions are not supported by your motherboard (again assuming it is an Asrock 775i65G)
Thanks a lot,
First of all, when saying that I have multi-operationgs systems, I mean there are two operating systems installed on my PC(SP2, SP3) both are 32Bit. The first Windows SP2(NOT installed by me) has all multimedia audio card installed
well, and has SCSI and RAID Host Controller shown the device manager. However, only the VGA is not installed on Windows SP2. However, the second one Windows SP3(Installed by me) has VGA not installed, Multimedia audio NOT installed, and there is no SCSI and
RAID Host Controller in device manager.
First: Why did the CPUz, specy didn't detect motherboard name, and only detect the model. IF I need to open the case and shine a light on the motherboard you can usually see both the manufacturers name and the model printed on
the pcb somewhere, then what benfit would be there from hardware detection software?
Second: Yes, my motherboard has integrated video, and integrated audio card
However, this doesn't mean that I don't need to install them since the Vidoe controller is not properly installed (it is a default VGA ) Also, Multimedia audio controller is not functiong at all.
Finally: if And if "SCSI and RAID Host Controller" is still not shown in Device Manager in Windows XP SP3, because these functions are not supported by my motherboard, then why is 'SCSI and RAID Host
Controller' installed/shown in the device manger in Windows XP SP2 on the same PC???
A man should convert his anger and sadness into strength to continue living in this life.

How to install the adobe creative cloud packager and how to apply the adobe ID for Admin user

Hi team,
Anyone has done install silently the captivate 8 using AAME? i try using this tool to create the msi but its not work.
i saw the previous disussion on captivate 7 and they said cannot use AAME and need to use CCP.
isit also applicable to Adobe Captivate 8? if yes cana anyone tell me how to download the CCP?
I already create my Adobe ID but when i try to login, its stated "Adobe does not recognize you as an authorized user of this web site."
How can i access this site? appreciate your help

The help I have been using (unsuccessfully) is here:
>These links provide additional guidance for deployment support
>Creative Cloud Packager Help: http://helpx.adobe.com/creative-cloud/packager.html
Dave

How to install 2-port vic3 2fxs/DID and 2-port vic2 fxo on cisco 2801 router

Similar Messages

Maybe you are looking for