How to install 3G Broadband Modem on my Tecra R850

i want to install a hardware for 3g mobile broadband in my Tecra R850 pt520a-01s003. is it possible?

Well, the Tecra R850 PT520A-01T00301 supports 3G broadband modem.
The point is that the SIM card slot is part of the motherboard and if your notebook does not support the SIM card slot, the upgrade would not be possible.
The sim card slot should be placed behind the batteryso you need to remove the battery firstly to check this.
The 3G card the PCI-E mini card can be connected to motherboard and its removable.
Furthermore the 3G modules needs an 3G antenna so the whole notebook needs to be disassembled to install and to hide the 3G antenna cables
The whole procedure will be really, really difficult and I think only an authorized service technician with good notebook experience could do that.

Similar Messages

How to Install 3G Broadband Modem in Tecra R850

My model Number is: TECRA R850 PT520A-01S003
I Found SIM card conector under bettery but no 3G modem Hardware installed.
I bought a 3G Broadband Card [Sierra MC8775 HSDPA ] but how to install?
B.R
srkhan
Attachments:
Sierra MC8775 HSDPA.jpg ‏143 KB

I don't know if all of the motherboards have the connectors needed, or if the models without the 3G card installed at the factory have the needed antenna.
There is a small port on the bottom of the computer that you can open after removing a screw. This allows access to the connectors for antennae to the WiFi and (if present) 3G cards. So you could at least see if the antennae are there(or at least their connectors).
However, the cards themselves seem to be larger than the port, and require pretty much a complete diassembly of the computer in order to get to the motherboard. And even then, it is possible that the connector for the 3G card may not exist on the motherboard.

Does anyone know how to instal a 33600bps modem on OS X 10.7.4?

Hello people from around the world!
I'm having a very hard time to find out how to instal a 33600bps modem on my OS X 10.7.4. The modem is conected to my MBP through a Prolific USB cable which I already have instaled. My problem is to be able to connect the MBP to this 33600bps modem.

Just to make sure I understand correctly:
This is a modem just for faxing or for an internet connection?
If it is for an internet connection, what company (ISP) are you dealing with???? This would be an extremely slooow dialup connection.
Most ISP's either require you to rent or purchase one of their modems or have an "approved and compatible model" list so you can go out and buy one yourself.

How to install printer and modem in solaris

Please send me detailed installation information about how to install a serial or aparallel printer on solaris 7 and 8 and also how to install the modem on solaris 7 and 8.pls send me some docs,informations etc.

Solaris 8 includes an "answerbook" CDROM that explains this
in great detail. Look in the <tt>Solaris 8 System Administrator Collection</tt> �
<tt>System Administration Guide, Volume 2</tt>.
You can also read the answerbook documentation online on
http://docs.sun.com.

How to install Toshiba software modem on Tecra M2

It has been a few months since I used dial up, then whilst travelling and found no ethernet cable to plug into I tried the dial up modem and it didn't work and was giving an error saying the modem was misconfigured or already in use.
On closer inspection it seems the modem was configured to use COM3 port which did not show up on the device manager listing. I tried to amend the com port to COM11 which was listed as unused and then the window hung though the rest of the laptop / XP worked.
I had to reboot the computer and found that the Toshiba Software Modem was no longer installed.
So I went to the drivers site and downloaded the driver and tried to install it. It spent a few minutes updating the drivers then the window closed without any error message. Going to control panel modems add modem have driver and clicking on the INF file did nothing.
So how do I get back the Toshiba Software Modem and when I do which port do I assign it to, also how do I know if all the COM ports are being recognised?

I have a tecra M1 and no modem will work on it. I first installed the 2000 OS drivers by mistake could not start device from the forums.
I realized my mistake and found the xp drivers. UNinstalled the old ones, XP drivers installed nicely; looks fine no errors no conflicts, working properly com port 3.
But when I query modem i get the port could not be opened it is busy please check the device manager for other problems with devices.
I do see that all items are installed correctly.
They are BUT I DID NOT INSTALL THE DRIVERS in the order prescribed in the instructions.
The modem got installed after lan and wireless and a bunch of other stuff.
I wanted to do a system restore to when I just installed windows XP Pro ( not the image of the M1) but I had not activated windows until after I installed the wireless drivers. I was afraid I would deactivate windows and that would be a bummer so I just created a restore point called "before I uninstalled drivers".
Then I went to the control panel add or remove programs and removed everything in the opposite order from the install instructions, when I rebooted the wireless and lan installed before the modem and the modem still was not functional even though it said it ws working properly in the DM>
Then I uninstalled wireless and lan installed the modem then rebooted AUGHHH. Not working
Well, before this I purchased a used modem and installed it and that set up fine also and did not work I got the same error message!!! AUGHH
THEN, I instaled a PCMCIA modem, It set up perfectly and got the same rror message. DOUBLE AUGHHHH
So thats when I go to thinking of the correct order of install and sigh..........
Well, if I system restore it, the way back to the time immediately after I installed windows and the rest will I be deactivated with Microsoft?
And do you think it would work?
If not if I wiped it and reinstalled XP and installed in the correct order do you think the modem problem would be fixed.
Any ideas?

Since installing my broadband modem & software why can't I shut down?

I have just got broadband,via a voyager 105 modem, but since installing it I have to hold down the restart button to shut down, and I get an error message on switching my mac back on that "Mac OSx shut down unexpectedly". I've tried clicking on the disconnect icon prior to shutting down but still the same thing happens. What's going on & how can I fix it? HELP!
Mac mini G4 Mac OS X (10.4) new switcher

If your using a BT voyager 105 this is a USB ADSL modem then you will experience difficulties. Unfortunately USB ADSL modems have never worked very well in OSX. USB ADSL modems require drivers to work on your mac. They have a history of being buggy and inefficient.
The only way to have a reliable ADSL experience is to replace your USB ADSL modem with an Ethernet ADSL modem/router.
An Ethernet ADSL modem does not require drivers and will work on any platform.

How to Install Netgear DGN2200 modem/router combination

My Netgear DGN2200-100NAS arrives today and I would like to know of any tips or suggestions in the setup and install for my iMac running 10.6.4. The installation CD only is useful for Microsoft PCs, and all installation scripts are for PCs only.
Any suggestions would be appreciated.
Thanks
Message was edited by: wmm5

I'm not familiar with that specific router but typically you don't need to install any software when connecting a router. Even PC users often use the router install DVD as a coaster instead of installing the software. If you are connecting the router to the usb port of your computer you will need to install the router's usb drivers. But connecting a router to the usb port is a bad idea. Just connect it to your cable/DSL line and to your computer(s) using Ethernet. It should automatically connect with default settings. Let us know if you run into problems.
Depending on who your ISP is, you may need to call them to register the modem with their service. I know you need to do this with Comcast otherwise their system won't allow your modem onto their network.
Message was edited by: BobTheFisherman

How to install nokia 6020 modem drivers?

i have a nokia 6020 phone,i want to used it as a modem for my pc but i cant install the .inf file that i downloaded... tnx for helping!

Please HELP!
My Nokia is 6020, I would like to use it as a modem for a notebook (with Windows XP).I have CA-42 cable with a disk, so Nokia PC Suite was installed on my notebook, but attempt to connect to the Internet was fault because the notebook regarded the built-in modem as appropriate one and the only potential. So I downloaded Nokia6020IrDA_2000_XP.inf drivers from www.nokia.ru . It didn’t work either. Now it identifies “PC Connectivity Bluetooth Modem - connected to COM6” (that is funny – I have no Bluetooth at all!). All Mobile settings are correct.

Possible to manually install moble broadband modem later on?

I'm getting a thinkpad helix and was wondering if anyone knew if it is possible to manually install the mobile wwan sim card slot manually after purchasing a model that does not include the mobile wwan feature? I found the same network card that thinkpad offers on amazon but don't know if I would be able to open the helix up and install the wwan card myself. Only reason I'm doing this is because I would like to buy the tablet now but lenovo doesn't offer any kind of financing so I'm going to use either ebay or amazon to buy a helix so I can use a credit limit I have with them to buy it. I'll have the money I just don;'t have the money right now. ANyway none of the helix on either ebay or amazon have 3g wwan capability which is the only problem. I want to be able to buy one on ebay or amazon and then install the wwan card myself. Would this be possible?

I don't know about sim card reader, but it's possible to add wwan card yuorself. Look at this service video under "Tablet FRU Videos" item:
http://service.lenovo.partner-management.com/content/CourseWarePublic/18124/player.html
Usually all new generation ThinkPads are "wwan ready" i.e.have sim card slot and wwan antennas kit. In this case they don't include special mark regarding wwan ready features in short model description on Lenovo site in opposite of previous laptop generation.
x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
Do it well, worse becomes itself
Русскоязычное Сообщество English Community Deutsche Community Comunidad en Español

How to install and configure a serial modem

Hi,
I just bought a real modem: a usr robotics v.92 56k, so I anyone guide me in how to install a serial modem in Solaris 10 x86.
Thanks very much,
Lorenzo Jimenez

http://forum.sun.com/thread.jspa?threadID=21835&tstart=0
btw, where are the duke dollars ?
Eric ;-)

Apple TV 3 Status Light turns ON and stays ON when I turn ON my Broadband Modem. How do I stop this ?

Since I updated my Apple TV 3 to 5.1.1, the Status Light turns ON and stays ON when I turn ON my Broadband Modem. How do I stop this ?
At the moment I have to go to the HDMI channel that my ATV 3 is connected to, wake the ATV, then put it back to sleep, to turn OFF the status lght.
When I first got my ATV I did not have this problem, when it was running 5.1.0.
I sent in a Feedback form, but they only as the option to select the OS version of a NON iOS device.
Is there a fix to this that wont involve me leaving my modem ON all the time ?
I turn my modem OFF when I am not using the Internet because I am a bit paranoid about the security of the data on my devices, and if I leave the modem turned ON all the time it might make me an easier target for hackers etc. { This is NOT part of my question, just explaining why I turn my modem OFF ( I feel safer ) }
<Edited by Host>

The ATV3 does that to me when I turn on my TV. the light goes on and stays on. If I switch to the ATV3, it seems to be half asleep with the light on ... I do wish Apple would enable the HDMI CEC and then everything would make sense. I've turned off my wireless and on again but the ATV3 light does not turn on automatically for me.
As you pointed out, I guess this could be a small glitch on the new firmware/software update... I wonder if this could be fixed by doing a restore from the iTunes app. I might give it a try tomorrow and see what happens...
Cheers!

Have installed OSX Mavericks and Vodafone Mobile Broadband Modem no longer connects despite reloading its software. Now cannot reinstall OSX Mountain Lion

Upgraded to OSX Mavericks. Vodafone Mobile Broadband Modem no longer connects. Tried again after reinstalling latest Vodafone Modem software update for Mac OSX, but no use.

Could somebody give a feedback about the solution proposed by Bokir?
I am experiencing exactly the same problem after upgrading to Mavericks with the Huawei E220 modem.
The connection is established for a few seconds, but no data is transfered, and the connection is then closing automatically.
I left the modem plugged in and the Vodafone software set to Automatic, and after numerous attempts and 10 to 15 minutes, it appeared that the connection was finally established.
That is of course no way to work.
After running the VMB uninstaller, there are still a lot of stuff in library cache & preference folder that are pertaining to VMB and not removed.
It is also strange that after uninstalling and reinstalling the VMB software, I am not requested to enter my pin code to establish a connection.
It is obvious that there must be some other VMB files (probably corrupted) somewhere in the system that are not removed by the uninstaller.
I have another macbook pro running VMB without problem and I am really afraid to install Mavericks on this laptop because of this issue.
Thanks again for any feedback.
Jean-Philippe

How to install USB modem MF110 ZTE to work in RDS network in Romania, on Mavericks?

Please help me!:)

How to install USB modem ZTE MF 110 to work on Mavericks, in RDS network, in Romania? Somebody knows? Please help me! Thanks a lot!

My ipod touchs location services has stopped working. I just installed a new modem to my pc could that be the problem and how to fix ? ive already reset the ipod to new status and no help. thank for any help

my ipod touch has lost location services after i installed a new modem to my pc . it is turned on in the settings and i have even reset the ipod to new status. Any help would be appreciated thanks.

Nothing you can do except wait until Apple adds the router to their database of routers and their location. If you or someone nearby does not have an iPhone it can take a while. There is no way to tell Apple to add a router to their database.
iOS 5: Understanding Location Services

I have a cannon MG 2920, I just purchased and installed a new modem/router how do I get the printer

I have a MG 2920 after installing a new modem/router I am unable tro print, error offline. The blue wifi light is on at the printer.

Did you reconnect printer to router?

How to install 3G Broadband Modem on my Tecra R850

Similar Messages

Maybe you are looking for