How to install an SRX400 behind a 2wire wireless router?

Any suggestions? I used the Linksys guide to setup the router behind the router with no issues. The second router acts as its own access point, accepts connections and even confirms an ip address, but will not allow thoughput or connectivity to the internet on a wireless connection. I can, however, hardwire connect to the linksys and connect with no issue.
Any suggestions for troubleshooting? Thanks.

How you have connected both the Routers to each other? As your 2Wire Router is your Primary Router, How you have connected Linksys Router to the 2Wire Router?
When you Hardwired your computer to the Linksys Router you are able to access Internet, But wirelessly you are unable to access internet? Is the wireless Settings of your 2Wire and Linksys are identical or its different. When you computer is Wireless, check whats the IP address its getting? To find out the IP address of your computer click on Start - RUN - CMD and click OK... In the Command Prompt window type "ipconfig" and hit enter and note down the IP address and check if the IP address is in the Range of your Linksys Router.

Similar Messages

Recently moved and installed ATT DLS - I use their wireless router and connectted my airport express - Now I'm getting the Blue ? on some images

Recently moved and installed ATT DLS - I use their wireless router and connectted my airport express - Now I'm getting the Blue ? on some images - and at times - videos don't load. I've increased / deleted Cache. Suggestions? Misconfig? Could it be possible my configuration from MacBook to router isn't correct?
Thanks!

JG,
Thanks for the info.
Couple of questions. I found an apple support document on this topic that opened with this line:
"AirPort Express and all AirPort Extreme base stations can use WDS. Earlier AirPort base stations can't."
If the TC is an airport extreme base station, why can't this work to extend the network? I think I misunderstand. Here is the full article:
http://support.apple.com/kb/HT2044?viewlocale=en_US
If I buy a new airport extreme, set it to wireless-n only as my main router, am I correct that my existing time capsule could be used as a bridge if plugged in upstairs?
Final question (and that should do it), could I take this old airport express, plug it in upstairs using the ethernet connection, and just create a separate wireless network to use with a different name?
I'd like to keep one network if possible but just kicking around short term solutions.
Thanks again.

How do I use Time Capsule as a wireless router and turn my current one into modem only

I have a crappy modem/ router and before I purchase a new modem I want to use the modem (no wireless) feature of my router.
Question #1
How do I use my Time Capsule as a router?
Question #2
If I do this will I still be able to wirelessly back up to my Time Capsule?
Question #3
How do I turn off (wireless) or the router function of my modem/ router?
Question #4
I then want to connect all my wireless devices to my Time Capsule making that
the main WIFi in my house. I am assuming this is possible it is I just dont know how to go about doing this myslef without guidance, and the Airport Installer is confusing to me.
Thanks!

Question #1
How do I use my Time Capsule as a router?
Connect an Ethernet cable from one of the LAN <-> ports on your modem/router to the WAN port (circle of dots icon) on the Time Capsule.
Open AirPort Utility and click Continue to follow the guided setup to configure the Time Capsule to "create a wireless network". Select the "Bridge Mode" option when it appears during the setup. (AirPort Utility will normally do this for you)
Question #2
If I do this will I still be able to wirelessly back up to my Time Capsule?
Yes
Question #3
How do I turn off (wireless) or the router function of my modem/ router?
We prefer not to guess at things, but since we do not know the make and model number of your modem/router, and this is an Apple support area, we have little choice.
In general, you would enter the default IP address of the device into your browser to bring up the configuration pages (check your documentatio on the modem/router for this information, or it may be on the back or bottom of the device. An example of a default IP address is something like 192.168.1.254
There will be a wireless settings page that will allow you turn off the wireless function of the device.
If you acquired the modem/router from your service provider, they should be able to tell you how to do this as well, or if you check the manufacturer's website, they will likely have a support area for questions like this.
Question #4
I then want to connect all my wireless devices to my Time Capsule making that
the main WIFi in my house.
You will need to log on to the Time Capsule wireless network from each device and enter the password to connect. Most computers will "remember" the setting so that you do not have to enter the password each time that you connect.

How can I turn off my Linksys 1200 wireless router?

Hi,
I just got a Linksys 1200 wireless router and wanted to know how (and the best way) I can turn it off (besides unplugging it) when I am out of town?
Thanks

hi there.
there is no on/off switch in the router. these devices are meant to run 24/7 so there's no off on it.

HT1731 Help installing Airport Express with Netgear N150 wireless router? I hav

Hi,
I just purchased the newer Airport Express (new) and am having issues using it in client mode with my Netgear N150 wireless router. All I want to use it for is streaming itunes from my aluminum macbook to my home stereo system, wirelessly.
I have followed the instructions that came with the device. No luck. I have followed the instructions that describe plugging it into an ethernet cable here:
http://support.apple.com/kb/HT1731
With the apple instructions linked above it would connect fine to my existing wireless network, using airport utility, with 'excellent' connection, but when I tried to switch in itunes to my device from my computer i get the pinning wheel and an 'unknown error' occurs.
I have setup a new wireless account and password on my router as desribed at this page, but do get confused when it tells me to use the hex key and $. Haven't worked that out yet. Any advice would be appreciated if this would help.
http://hints.macworld.com/article.php?story=20041017233832771
At best, after hard resetting the device several times, and following the instructions above at macworld, it now finds the device but only plays one blip second of a song, flashing amber from solid green, sometimes playing a second blip of a song, then pausing the song and switching to a flashing amber. By restarting my computer or opening AirPort utiliy I am able to find it again, but it either only plays one second of a song and drops again or turns green and is not able to be found at all by itunes (the button doesn't show up in the menu).
This is the second airport I have tried in 2 years. I purchased a used one and had nearly the exact same issues with a linksys router. Then it would play an album but reset if a song was paused.I had to hard reset it nearly every time i wanted to stream from itunes to my stereo. I assumed it was broken and sent it back. Figured I 'd give it a new go around with a new unit since i just moved into a new house and am now shocked at how difficult it is to set up. I have never had this many issues with an apple device.
My questions:
1) How can I set this up with my existing router? What am I doing wrong?! Why is it so difficult?
2) If not possible, what routers are compatible? I would gladly get a new router in order to stream music to my stereo from ITunes.
thank you for any assistance. i am pulling my hair out.

Try temporarily disabling the Windows 7 firewall, and then, try accessing the AirPort with the AirPort Utility again.

How do I set up my SSID to wireless router

Have HP3052A J611g printer that I cannot get to connect to my 'Clear' brnd wireless router. It is a plug in and go to electical outlet, There are no buttons on this unit..
My Mac Air Book does recognize this printer with correct model number in tact, but cannot connect.
I do have a SSID number from my Clear internet connection product. I cannot find a way to get my HP printer network name to match this wireless outer network name (SSID) exactly.
I can get the printer to get the wireless connection to 'on', but goes off on it's own within seconds.
Please advise.

Ensure that the Airport base station is configured to not distribute IP addresses.
On the iMac
System Preferences > Sharing > Printer Sharing
On the PowerBook
Applications > Utilities > Printer Setup Utility
Add Printer
It may work with the HP driver (which you will need to install on the PowerBook)
It may work with a third-party driver such as the HPIJS drivers or the Gimp-Print drivers, but this is not the case with all printers.

Make my iMAC run wirelessly with my ATT 2wire wireless router

How do i set up my iMAC to run wirelessly w/ my 2wire router?

Bob:
I've been following a lengthy discussion in the forums regarding Snow Leopard's problems connecting with 2Wire modems. Is it possible that Pam's experiencing that issue?
Since I'm here, could you answer a related question for me? I'm trying to connect a new MacBook Air to my AE network, which already has a MacBook Pro on it. The Air won't connect because the two machines use the same IP address. I know how to change the Air's IP settings, but don't know enough about IP addresses to know what I can change it to so it works. Any thoughts?
Thanks,
Don

How to test the encryption used in my wireless router?

How can I test my router for weak encryption keys? WEP and WPA..

If you're using WPA-PSK/WPA2-PSK and your PSK is short (<20 letters) and it's a "normal" word (from the dictionary) it's possibe to hack it. WPA2 is a bit more secure but good PSK is important.
This article describes details about hacking WEP/WPA. Unfortunatelly it's not free but maybe you can find a printed version of this magazine in your country in some library or you can just buy the article.

How do I get a password on my wireless router?

I think I found a person on in My Finder sharing my network. I'm not too happy. When we set up our router
it didn't ask for a password, so we don't have one. I'm not too computer savvy, but can do the basics.
Help..not sure what I can do ? I'd like to have a password so people can't get onto my network.
Thanks for the help
April

There are two different passwords at issue here. They aren't necessarily the same, and shouldn't be the same.
One is the password you use to get into your router settings. If you don't know what that password is, you'll have to reset your router to its factory default settings. I can't tell you how to do that. There's probably either a button to press or a pinhole into which you insert a paper clip. After you reset the router, it will have a default password, which you must change immediately. The default password is in the documentation somewhere. Find that documentation on the manufacturer's website.
Do not leave the default password set.
The other password is the network password, which you set within the router's web interface. I can't tell you how to do that either. Make sure you select WPA2 Personal as the security standard, not WEP. If the router doesn't have that setting, recycle it and get a newer one.
See this support article for the possible formats of wireless network passwords:
AirPort: Joining an encrypted WEP or WPA Wi-Fi network

How do I find the IP of my wireless router??

I know this a bit off-topic, but it seemed the only place to post this. . .
I've bought a belkin wireless router so i can use my laptop round the house (the airport extreme in my G5 is too weak to get through our walls). The laptop (and my PSP ) finds the belkin and connects to the internet/network through it, but I cannot access the admin page of the router to set up a password. I'e entered the IP address listed in its manual, but it doesn't connect to anything. I've tried other obvious numbers with no success.
There's nothing about this on the belkin site, and I've searched Versiontracker to see if i can find anything that will scan my network for it - does anyone have any suggestions
Cheers
Steve

First, I would reiterate what previous posters have suggested, using a browser besides Safari. I know first hand that Safari does not play well with Belkin gear.
If not, try this:
1. Finder>applications>Utilities>network Utilities.app
2. Use the "traceroute" function and use something like www.google.com. Most likely the first IP returned is your gateway.
3. Use the "port scan" function to scan all ports using the IP above (leave the field blank) and check the returned ports. Almost all routers use port 80 but some may be configured to use 8080, 443 or some user defined port.
4. Try connecting to the router by typing http://192.168.1.1:8080 for example using the ip address of the gateway and the ports retuned by the tools separated by a colon. Also try https://x.x.x.x The router may have been set to only connect using ssl/tls via port 443
5. If none of this works you could try doing a factory restore which will be outlined in the manual for the router. Just be advised that any configuration currently in the router will be lost for good.
Good luck. If any of this doesn't work post back for more ideas.

How do I get Ipad mini online using wireless router

I have a new Ipad mini and access to a wireless router. What do I do to get on the internet?

Skydiver 119,
That resolved my issue.
Thanks.
Prairie hawk

How to set up DDNS with a BEFW11S4 wireless router

I dont see any obvious way to set up a DDNS server on this product. Any help?
Message Edited by bixfisher on 06-11-2009 08:24 AM

The Router offers a Dynamic Domain Name System (DDNS) feature. You can choose which services you want to use. The two choices are :
DDNS.org : http://www.dyndns.com/
TZO : http://www.tzo.com/
You have to sign up with the Service DynDNS or TZO...
Access your router's web interface and go to the DDNS tab under the Main tab 'Setup'

How do install EPC header on the ASR router? or is it now part of the IOS?

There was a discussion of using the router to look at the trace capture from the router, I downloaded the EPC header, but don't know to install. Is there any documentation on how to install the script file onto the ASR router? Thank you
Osh

Which script is this exactly?

I've installed windows 7 with the help of bootcamp on my macbook pro 2011. Please help me how to install mac drivers for windows7 64 bit???

I've installed windows 7 with the help of bootcamp on my macbook pro 2011.
Please help me how to install mac drivers for windows7 64 bit???

You either download drivers from within Boot Camp Assistant and save to USB FAT disk, or you insert and use 10.6.x OS X DVD when in Windows and install and run the SETUP from there.
General Help:
Boot Camp 4.0, OS X Lion: Frequently asked question
http://support.apple.com/kb/HT4818
http://manuals.info.apple.com/en_US/boot_camp_install-setup_10.7.pdf
create a Windows support software (drivers) CD or USB storage media
http://support.apple.com/kb/HT4407
Installation Guide Instructions for all features and settings.
Boot Camp 4.0 FAQ Get answers to commonly asked Boot Camp questions.
Windows 7 FAQ Answers to commonly asked Windows 7 questions.
- support articles and tips, how to.
http://www.apple.com/support/bootcamp/
Macs that work with 64-bit editions of Microsoft Windows Vista and Windows 7
http://support.apple.com/kb/HT1846
Step 4: Install the Boot Camp Drivers for Windows
After installing Windows, install Mac-specific drivers and other software for Windows using your Mac OS X installation disc. The Mac OS X disc installs drivers to support Mac components, including AirPort,built-in iSight camera, the Apple Remote, the trackpad on a portable Mac, and thefunction keys on an Apple keyboard.
The Mac OS X disc also installs the Boot Camp control panel for Windows and theApple Boot Camp system tray item.
To install the Boot Camp drivers:
1 Eject the Windows installation disc.
2 Insert the Mac OS X disc. If the installer doesn’t start automatically, browse the disc using Windows Explorerand double-click the setup.exe file in the Boot Camp directory.
3 Follow the onscreen instructions.
If a message appears that says the software you’re installing has not passed Windows Logo testing, click Continue Anyway.
Windows that appear only briefly during the installation don’t require your input.
If nothing appears to be happening, there may be a hidden window that you mustrespond to. Check the taskbar and look behind open windows.
Important: Do not click the Cancel button in any of the installer dialogs.
4 After your computer restarts, follow the instructions in the Found New Hardware Wizard to update your software drivers (Windows XP only).
5 Follow the instructions for any other wizards that appear.
6 Check for updated Boot Camp drivers by using Apple Software Update or going to www.apple.com/support/bootcamp.
If You Have Problems Installing the Device Drivers
If it appears that the Boot Camp drivers weren’t successfully installed, try repairing them.
To repair Boot Camp drivers:
1 Start up your computer in Windows.
2 Insert your Mac OS X installation disc.
3 If the installer doesn’t start automatically, browse the disc using Windows Explorerand double-click the setup.exe file in the Boot Camp directory.
4 Click Repair and follow the onscreen instructions.
If a message appears that says the software you’re installing has not passed Windows Logo testing, click Continue Anyway.
If you need to reinstall specific drivers, you can install one driver at a time. For example,if your built-in iSight camera isn’t working, you can reinstall just the iSight driver.
Individual drivers are in the Drivers folder on the Mac OS X installation disc.

How to install adobe premier trial.........pls

how to install adobe premier trial.........please guide me

Well going by your standards then the blackberry playbook is just as useless since there is no native contacts app or email app. If you want that you will also have to have a blackberry phone that is capable of tethering using the blackberry bridge app (if allowed by AT&T and Verizon since that would be another fee technically you might be charged for since you will be tethering your phone to you tablet).
Funny how I and many others are able to get by using the iPad and we don't have flash. The majority of people if the want to view flash will try Skyfire, iSwifter, Cloudbrowse, or will look to see if there is an app already dedicated to that thing you want to watch, like ABC Player or CNN.
Hey if doesn't work for you then it doesn't work for you. I am not trying to come off as an Apple fanboy, just trying to make sure you are informed about your product and what options are out there.
Would it be nice if flash was allowed native......sure. But it isn't so you can either get rid of the product, get an app that supports it (we are talking about spending $2 - $4) or go buy something else and hope your happy with it as well. You can't please everyone. Apple has chosen their stance and as you can see by sales numbers they aren't hurting. Infact i just read about a week or so ago on Gizmodo.com that alot of the other tablet making companies are cutting back on the number of units they will be making due to low sales or projected low sales (you can thank the iPad sales for that). Your one purchase isn't going to impact them that much. Instead, someone else will be standing in line behind you ready and happy to get their apple product.

How to install an SRX400 behind a 2wire wireless router?

Similar Messages

Maybe you are looking for