How to install NIC driver on Solaris 10?

I see the driver for my NIC, the D-Link DFE-530TX+ at this site
http://homepage2.nifty.com/mrym3/taiyodo/eng/
It talked about this NIC on choice #4, but how do I go about installing the driver rf-1.1.0.tar.gz on Solaris 10 x86 to make this NIC work? Thanks.

if it was choice number 4, then choose it.
other wise check out D-link site for unix/linux advice. maybe, I'm just a newbie myself.

Similar Messages

  • How to install NIC driver

    I'm very new to Solaris and I need to install RealTek 8169 driver. How do I unzip and install? Any help would be greatly appreciated.

    Where did you get the driver? This page perhaps?
    http://homepage2.nifty.com/mrym3/taiyodo/eng/
    If so, here are the instructions for compiling and installing it:
    1. Introduction
    This is the Realtek RTL8169/8110 giga bit ethernt NIC driver for Solaris.
    It is distributed under the BSD license.
    2. Specification of the driver
    File name of the driver: /kernel/drv/gani
    Special file name: /dev/ganiN (Where N is a unit number, typcally 0 for first
    card)
    For example
    % ifconfig gani0
    RTL8169/8110 chipset dosn't support 1Gbpis half duplex mode.
    Currently gani driver isn't stable on sparc platforms.
    Tested OS version
    Solaris10 x86 3/05 (Athlon 2800+ w/ VIA K8T800 chipset)
    Solaris10 x86 3/05 (Athlon 3000+ w/ nVIDIA nForce4 CH8-04 Ultra chipset)
    Tested cards
    RTL8169s -- Planex Communications GN-1200TC
    RTL8169s -- Corega CG-LAPCIGT
    3. Preparing for installation
    (1) Install your PCI card and boot Solaris.
    (2) Copy source and binary files.
    # gunzip -cd gani-x.x.x.tar.gz | tar xf -
    (3) Add hostname for the NIC card into /etc/hosts file
    (4) Make links to correct binary directory and Makefile according to your
    configuration. i386 and gcc are default.
    % cd /.../gani-x.x.x
    % rm obj Makefile
    % ln -s Makefile.${KARCH}_${COMPILER} Makefile
    % ln -s ${KARCH} obj
    where ${KARCH} is the result of `isainfo -n`, and ${COMPILER} is
    "gcc" or "suncc" which you want to use to make the driver.
    (5) Making binaries (only for sparc platform)
    Gani driver is ready for 64bit and 32bit solaris8 10/00 sparc or
    later. (But currently it is unstable on sparc platforms.)
    This distribution does not include sparc binaries. To make the binaries,
    you need Sun C compiler or gcc version 3, and do the following operations.
    % /usr/ccs/bin/make
    4. Testing
    Testing before installation is strongly recommended.
    # cd /.../gani-x.x.x
    # /usr/ccs/bin/make install
    # ./adddrv.sh
    # /usr/ccs/bin/make uninstall (for solaris7, don't remove the file )
    # modload obj/gani
    # devfsadm -i gani (for solaris7, use drvconfig and reboot with -r )
    # ifconfig ganiN plumb ( where N is an instance number, typcally 0 for first card)
    # ifconfig -a ( you will see an entry for ganiN)
    # ifconfig ganiN YOUR-HOST-NAME
    # ifconfig ganiN ( ensure IP address is correct)
    # ifconfig ganiN up ( and then you can test with ping, telnet, ftp ...)
    5. Installation
    After you ensure that the gani driver is fully functional, install it.
    (1) install the gani driver into the kernel directory
    # cd /.../gani-x.x.x
    # /usr/ccs/bin/make install
    If you do not test the gani driver yet, execute the following commands:
    # ./adddrv.sh
    # devfsadm -i gani (for solaris7, use drvconfig and reboot with -r)
    (2) Configure the network interface. Create and/or modify the following file:
    /etc/hostname.ganiN
    (3) Reboot the system.
    # init 6

  • How to install lan card in solaris 11

    Hi,
    can some one please tell me how to install lan card in solaris nevada snv_55b X86, 5.11
    When i do ifconfig -a it only displays loop back driver only
    lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
    inet 127.0.0.1 netmask ff000000
    The other driver was missing can please some one tell me how to install that?

    Well, the lan card has to be one that is supported by Solaris and you need to have the proper driver installed before you'll be able to get it running. A good starting point would be to look at the Solaris Hardware Compatability List (HCL) at:
    http://www.oracle.com/webfolder/technetwork/hcl/index.html
    There is a blue box which says "Check out the X86 device list" which may be a good place to start. You won't be able to pick out Solaris version you're running for the OS type menu but if you can find the device anywhere you should at least be able to determine which driver it uses so you can check that against your system. If you don't have the driver package installed, you'll have to install it before you can see the device. If course, if the device isn't supported you're stuck. At least the HCL can help you select a new interface card which should work.

  • Trying to install nic drivers for solaris 10 on x86 machine

    i am trying to install nic drives for sis 900 downlaoded from http://homepage2.nifty.com/mrym3/taiyodo/eng/
    i am following the instruction in the readme file but when i reach
    (5) Make links to correct binary directory and Makefile according to your
    configuration. i386 and gcc are default.
    % cd /.../sfe-x.x.x
    % rm obj Makefile
    % ln -s Makefile.${KARCH}_${COMPILER} Makefile
    % ln -s ${KARCH} obj
    where ${KARCH} is the result of `isainfo -n`, and ${COMPILER} is
    "gcc" or "suncc" which you want to use to make the driver.
    when i execute the command
    ln -s Makefile.i386_gcc Makefile
    it gives me an error
    what should i do

    hi, your files and folders may be named by UPPER symbols. Rename them by LOWER symbols.
    goodluck !!!

  • How to install hard drive into mac pro

    how to install hard drive into mac pro

    I recently bought a new 2TB internal sata drive for my Macpro.
    The installation was easy, but I'm not sure what to do next.
    For one, should I partition the drive?
    My purpose for buying the drive was to use it as my go to drive for Parallels. I used to run my music studio on Windows based machines, and my older project files require a windows OS to recover. I installed Parallels so I can have my studio running Mac and Windows programs which will enable me to access my old project files and take them into my newer Protools system.
    So now, I've installed my new hard drive, but I'm not sure if I should partition it....And!? I'm not sure how to designate that drive for my virtual pc on Parallels. I was able to allocate enough disk space to parallels in order to load my music software, but at this point, I'm not sure if I've just promised it disk space from my original partitioned drive (which only has about 350 GB left on it).
    I would love to be able to make one internal drive available for Parallels, and the other available for the rest of my OSX. When I use Parallels, I still would like to save some extra information on the 2TB drive as well from my dekstop running OSX.
    I hope this makes sense! Your help is much appreciated!

  • How to installed java comm in solaris

    I have installed borland jbuilder5 enterprise edition,and
    put the libSolarisSerialParallel.so in LD_LIBRARY_PATH
    (LD_LIBRARY_PATH=/usr/lib), the comm.jar in jre\lib\,javax.comm.properties in jre\lib .
    But when I Open the serial port, the program always raise a exception "null".
    What can i do ?

    sorry :
    how to "installed" java comm in solaris
    --->
    how to install java comm in solaris

  • How to install OpenGL files on Solaris 10

    I found OpenGL stuff is missing from the Solaris 10 system when I installed gtkglext from its source code and got an error after the 'configure' command.
    bash-3.00$ ./configure
    checking GL/glx.h usability... no
    checking GL/glx.h presence... no
    checking for GL/glx.h... no
    configure: error: Cannot find GLX header
    I remember that for software groups during Solaris 10 installation, I did choose the Entire Solaris Software Group to guarantee the developement packages are installed. Could you give some help on how to install opengl stuff from Solaris 10 installation disks?

    It's hard to believe that no one here (official Sun
    developer network) can answer my question. Maybe few
    people develop under Solaris.That must be it.

  • How to install hl2240dw driver update osx 10

    how to install hl2240dw driver update osx 10

    if it was choice number 4, then choose it.
    other wise check out D-link site for unix/linux advice. maybe, I'm just a newbie myself.

  • How to install scan driver with canon ir2025

    how to install scan driver with ir2025

    Thats simply
    Access the Toshiba European driver page and download the Toshiba graphic driver designed for you notebook series.
    Then start the device manager and uninstall the present graphic driver.
    Then reboot the notebook and then install the downloaded graphic driver on your system
    Thats all ;)

  • Install RTL8139 driver in Solaris 10

    Dear All,
    I am new to solaris 10. plz explain me where can i get RTL8139 LAN driver for solaris
    10 and how to install the same.
    Thank you in Advance.
    Regards
    P.Bharathiraja.

    You start by looking in Sun's Hardware Compatibility List (HCL) for Solaris.
    [http://www.sun.com/bigadmin/hcl/data/sol/|http://www.sun.com/bigadmin/hcl/data/sol/]
    In there, you will see that you have three choices for the 8139x chipset.
    You let the NIC be recognized natively during the OS installation (it just works), or you can use Realtek's driver from their web site, or you can use the third-party drivers hosted on Masayuki Murayama's site.
    The downloads from Realtek and from the Murayama site include README files with instructions.

  • How to install sound driver in HP Compaq Presario C794VU laptop in windows XP

    i want to install sound driver in windows XP in my laptop HP Compaq Presario C794VU.
    i have driver setup. i have run the setup but sound not comes.
    please give me the procedure how to install the sound driver. thank you

    Hi,
    First install correct MS-UAA:
    MS-UAA for XP with SP2 (required with a reboot before Audio and Modem) here
    MS-UAA for XP with SP3 (required with a reboot before Audio and Modem) here
    Only when you will do this download:
    Conexant High-Definition SmartAudio 221 here
    Unzip to a folder..use Device Manager,right click "Audio Device on HD",choose Update driver,
    No to connect,
    Install from a list or specific location,
    Select Don't Search, I will choose the driver to install,
    For the Hardware Type select 'Show All Devices'
    Remove the check from "Show Compatible Hardware" and click on "Have Disk".
    Next...browse to the unzipped folder and choose the "WiSVHe5.inf".
    Ignore XP when it complains.
    Reboot.
    ** Say thanks by clicking the "Thumb up" icon which is on the left. **
    ** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

  • HOW TO INSTALL OLDER DRIVE for EPSON r1800

    Hello
    SInce I upgraded to Lion, my Pictures are no longer printing as WYSIWYG on my Epson R1800. It seems from forums, that the newer driver isn't working corectly. I was able to find the installation DMG of an older Driver - but it is not found by the R1800 under System Perferences. Can you tell me how to install an older Driver?
    THanks
    Art

    "...It seems from forums, that the newer driver isn't working corectly..."
    What forums? The driver should work properly.
    http://www.epson.com/cgi-bin/Store/support/supDetail.jsp?BV_UseBVCookie=yes&oid= 14121&prodoid=53540919&infoType=Downloads&detected=yes&platform=OSF_M_X7

  • How to install puppet agent on solaris 10 sparc

    I would like to know how to install and configure puppet on solaris 10 sprc

    Proxy configurations are most often done within the application software that needs that function and not necessarily done in the OS.   That permits you to make very specific settings and not just generic global settings that could conflict with other software.
    Can you tell us what research you have done on the topic? 
    For example, have you glanced through a Google search on "solaris web proxy" ?
    If you are hoping to use a specific web server application your forum post might be better placed in a forum space for that software instead of in a general OS forum space.   What application software will you be using?

  • How to install OJDBC driver for oracle in PI7.1

    Hi,
       I am getting the following error for JDBC adapter communication .
    Error during database connection to the database URL 'jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS_LIST=(ADDRESS=(PROTOCOL=TCP)(HOST=x.x.x.x)(PORT=x.x.x.x)))(CONNECT_DATA=(SERVICE_NAME=cpuerp)(SERVER=dedicated)))' using the JDBC driver 'JDBC DRIVER: oracle.jdbc.driver.OracleDriver': 'com.sap.aii.adapter.jdbc.sql.DriverManagerException: Can not establish connection:: SAPClassNotFoundException: JDBC DRIVER: oracle.jdbc.driver.OracleDriver'
    Would like to install the OJDBC14.jar for oracle in PI 7.1 Can anybody help to let me know how to install the OJDBC.jar file in PI7.1?
    Thanks
    Regards
    suk4023

    Hi Sukande,
    Deployment procedure is same irrespective of operating system.
    On AIX, you have to copy the file com.sap.aii.adapter.lib.sda to your desktop and modify using winrar as explained in the below article and copy the modified file back to the respective path on AIX server.
    http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/00b4a020-4ae6-2c10-5a95-fed4ad9a4b60?QuickLink=index&overridelayout=true
    Thanks,
    Siva Kumar

  • How to install Printer driver *

    Hi,
    How to install HP printer driver , so that i can see new device type in SPAD.
    Thanks
    Lisa

    Hi Lisa,
    you need to use the program RSTXSCRP, but take care and check documentation maybe on http://help.sap.com
    Good luck
    Fred

Maybe you are looking for

  • No "Remote-User" in HTTP header when HTTP request gets to WLS

    Hello Exprers, I have a customer, using 10.3.3 on Linux machine. Web server as Apache. He wants Remote-User in HTTP header, he used to get it when he used Tomcat. But when he transffered to Apache and 10.3.3, he is not getting the Remote-User in head

  • Multicube - Version comparison of field assignments

    Hi, I added a new field in the infocube and accidentally messed up with multicube assignments and clicked on 'Assign all infoobjects' instead of selecting just one field. The problem is that I did not realize my mistake and transported the CTS to pro

  • Agewise Reports for Vendors - Transaction Code?

    Agewise reports for Vendors are needed. What would be the best way and the Transaction code?

  • Changing Lead Status

    Hi All, I am trying to change lead status when saving. I have configured action profile as follows: Created new action in action profile Processing type: Method Call Method Used: Complete_document ( Am I using right Method?) Processing Parameters: PR

  • Cannot open ACR preferences in bridge

    I get the 'qualifying product' error.  I have updated it to the latest ACR, opened PS4 first, and luanched bridge from there...all with no luck. Is tehre a dead link somewhere that needs to be fixed?  ACR is in the right folder and everything. I have