How to install original win8 os in hp pavillion dmv i5 laptop

as I formated my hardisk due to virus problem
so now I unable to install win8 os
following constant I have:
6 recovery DVD
laptop and adapter
problem:
I unable to install os
I don't know how to recovery and install operating system..
plz give the procedure how to do that....

When requesting assistance, please provide the complete model name and product number (p/n) of the HP computer in question. HP/Compaq makes thousands of models of computers. Without this information it may be difficult or impossible to assist you in resolving your issue.
The above requested information can be found on the bottom of your computer, inside the battery compartment or on the startup BIOS screen. Please see How Do I Find My Model Number or Product Number? for more assistance locating this information. DO NOT include your serial number. Please enter the model/product information into HP's Online Consumer Support page and post it here for our review.
Please see Performing an HP System Recovery (Windows 8) for general instructions and Recovery from recovery discs (Windows 8) for specific inferomation on using your DVD's to recovery your computer.
If you have any further questions, please don't hesitate to ask.
Please click the White KUDOS "Thumbs Up" to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Similar Messages

Need help- have no idea how to install original airport on G3 Powerbook

I just bought an ornignal airport card on ebay. I have no idea how to install it (i think it goes under the keyboard, but specifically where?) also, it didn't come with any software...do I need some kind of driver? I am so confused. All I know is that I spent over $100 for this thing and would love it if I could get it to work. Really want to go wireless...can anyone please help. (already checked all over the support page and called apple and asked them to point me in the right direction, but have gotten no where. thanks in advance.

Thea,
I get the impression you cannot return the AirPort card...this would be my first choice. Since the card is not recognized, either the card is bad or your powerbook has a hardware issue (doubtful).
Do you have an Apple Store nearby?
You might also contact your local User Group...there should be good help available:
http://www.apple.com/usergroups/
Your alternatives are these:
- find another original AirPort card (limited to the slower 11Mbps speed) to try;
- remove the internal AirPort card and buy a one of these wireless PC cards that run at the faster 54Mbps speed and are simply inserted in the PCMCIA card slot on the side of the 'book:
http://www.sonnettech.com/product/aria_extreme.html
http://www.macsense.com/product/broadband/WPE800.html
http://www.asante.com/products/productsLvl3/AL5403_XG.asp
http://www.buffalotech.com/wireless/products/airstation/WLICBG54A.html
The above cards have the Broadcom chipset that Apple's AirPort software supports. If you have already installed AirPort 3.1.1, you are ready to go.

How to install original 10.5.5 disk on erased hard drive in macbook pro

Macbook pro 5,1 late 2008 was running SL 10.6.8
Formatted hard drive in target mode from a mavericks mbp (mid 2012)
original 10.5.5 disk will not install.
gray screen with question mark press option and disk mounts but does not open-blue screen

Examine these options:
http://www.cnet.com/news/installing-os-x-with-a-broken-optical-drive/
Ciao.

How to install ios 5.1.1 on iphone 3gs

how to install original ios 5.1.1 on iphone 3gs

You don't. The only iOS version that can be installed on that phone, at present, is iOS 6.0.1.

How to install an SSD in a MacBook Pro and keep the original hard drive

Step by step instructions on how to install a Crucial SSD as the primary drive in a MacBook Pro and use the original hard drive as a second drive in place of the optical drive.
Apart from the time needed to back up your data and clone the original drive to the new SSD, you should be able complete this in less than an hour.

Verifying
Install the SSD in the HDD slot
Install the HDD in the optical slot
Boot to the HDD and format the SSD
Boot using Command R and restore the operating system from Time machine to the SSD
Reformat the HDD and restore the data files to it.

HOW TO INSTALL ACROBAT X STANDARD ON WIN VISTA 64 BIT. FROM ORIGINAL CD. GIVES ERROR MESG .. ?

HOW TO INSTALL ACROBAT X STANDARD ON WIN VISTA 64 BIT. FROM ORIGINAL CD. GIVES ERROR MESG .. ?
WHILE I WAS USING THIS APPLICATION ON SAME OS

Hi shaz2048,
Could you please provide us the Error message or the screenshot of the Error. Also did you try installing the software after copying the contents from the disc onto your computer.
regards,
Abhijit

How to obtain original legitimate Leopard install discs?

Hi, I'm the proud owner of Snow Leopard but my poor old dad still has Tiger - he would dearly like to upgrade but requires Leopard prior to installing Snow Leopard. Trouble is Apple don't provide or sell older OS software - and the only place I can find is on eBay but it all looks dodgy to me.
Has anyone any idea how to obtain original legit Leopard OS?
Many thanks, Chuckles

Hi,
Here is the UK web site to get Snow Leopard.
http://store.apple.com/uk?cid=OAS-EMEA-DOMAINS-applestore.co.uk
Go there and you should be able to find a shop near you to buy it.
Good luck,
Alan

How to install Aperture without original dvd

I lost my Aperture 2 installation and Aperture 3 upgrade disks. How to install Aperture in my new Macbook ?

Do you still have the Aperture 2 and Aperture 3 registration codes? Then you can download the Trial installer and use that to install Aperture on your new Macbook.
You can download the Aperture 3 trial installer to reinstall Aperture from this webpage - there is a link to the trial and instructions on how to reinstall - don't let the title of this page distract you :
Aperture 3.4: May quit unexpectedly on launch after updating
The Aperture 3 serial number will be available in the about panel, when you are running Aperture on your old mac (from the main menu bar: Aperture > About Aperture).
Regards
Léonie

How to Install Coldfusion 8 64-bit on Small Business Server 2008 64-bit

How to Install Coldfusion 8 64-bit on Small Business Server 2008 64-bit
I ran Coldfusion 8 on SBS 2003 Premium for 6 months with no problems. When we finally decided to cut over to SBS 2008, that’s when everything went to hell. I tried for weeks to get Coldfusion 8 to install properly on the new SBS 2008 64-bit box. During the course which, I found bits and pieces of information for Vista 64-bit and Windows Server 2008 64-bit installations. There are some distinct differences, however, with SBS 2008 since it runs core Web applications like OWA, RWW and Companyweb. After countless unsuccessful attempts, one of which completed corrupted the box, I found the solution.
I have attempted in this white paper to detail the steps to assist others who may be in a similar situation. I don’t make any warranty for the information, but so long as you follow the steps carefully you should be fine. BTW, for those of you who say Adobe offers free technical support for licensed users, that’s not entirely true. Like I said, I purchased CF8 and originally installed it on an SBS 2003 Premium box. After we cut over to SBS 2008 and encountered problems, Adobe wouldn’t provide any technical support without charging. Moreover, based on my initial conversations with Adobe’s technical team, no one seemed to know much about running 64-bit on SBS.
From my understanding, only two versions of Coldfusion 8 can be installed in 64-bit: Enterprise and Developer. The “normal” install (which I paid a grand for) can only be deployed in 32-bit mode – gee, THANKS Adobe! By the way, in Developer mode only two distinct IPs can access the site in addition to the localhost. Any additional IPs will result in a CFML error message stating that the maximum number of IPs have been exceeded. At any rate, take your time and follow the steps to achieve a successful installation.
PRE-INSTALLATION TASKS
Back Up SBS
It’s always a good practice to backup your server before deploying any kind of major system changes. Although this step is optional, I recommend it in case you need to restore your server for any reason. Bear in mind, if your system ever gets totally corrupted, you cannot restore back from the twice daily incremental backup images alone. You will need a full backup with system recovery information to restore. Here are the basic steps:
Click: Start > Programs > Administrative Tools. Right-click “Windows Server Backup” and choose “Run as administrator”.
Click “Backup Once” under Actions in the right-hand pane.
Choose the “Different Options” radio button under Backup Options.
Choose the “Custom” radio button. What we’re primarily interested in here is backing up the OS – not your data partitions or attached drives.
Select the “SYSTEM (C)” checkbox, uncheck any others. Also, ensure that the “Enable system recovery” checkbox is selected before continuing on.
Under ‘Specify Destination Type’, I usually select the “Local drives” radio button and point it to a Terrabyte USB drive I use for backups. You can point this to a tape drive, or select the “Remote shared folder” radio button if you map to a UNC path to store your backup images. Just remember, make sure that whatever path you select can readily be accessed in the event of an emergency. Also, make sure the “Verify after writing (recommended)” checkbox is selected.
Under ‘Specified Advanced Option’, I usually select the “VSS full backup” radio button instead of the default since I don’t use a 3rd party backup product. If like me you rely solely on SBS for your backups, choose the full backup option.
Confirm everything and click “Backup”. This process may take several hours depending on the size of your system.
Verify ISAPI Filters:
In IIS Manager, double-click the server instance in the left-hand pane.
In the center pane under IIS, double click the “Modules” icon to verify that the ISAPI native modules are already installed for IIS. If it’s set up correctly you should see two entries:
IsapiFilterModule %windir%\System32\inetsrv\filter.dll
IsapiModule %windir%\System32\inetsrv\isapi.dll
If either of these modules are missing, you will need to re-install these (google for a solution).
Set Up Development Environment
Create a directory for your CFML files outside of the default Windows location (e.g., default is usually C:\inetpub\wwwroot\). For the purpose of our install, I created a directory on a separate disk called: D:\DEV.
Copy and paste your CFML files and directories into the new DEV root Web directory. This will eventually be the directory where the Coldfusion installer places the CFIDE and CFDOCS folders.
Open IIS Manager and double-click the server instance in the left hand pane. Expand the “Sites” folder. Right-click the Sites folder and select “Add Web Site”.
Enter a name in the “Site Name” box (e.g., “test-site”). You will notice that the system will automatically create a corresponding Application Pool with the same name. NOTE: this is important to prevent conflicts between the DefaultAppPool (needed for SBS Web apps like OWA, RWW, etc.) and the application pool needed for Coldfusion to function properly in SBS 2008.
Point the “Physical Path” to the directory you created in step #1 above (e.g., “D:\DEV”).
Don’t worry about testing the connection. If you click “Test Settings” you may receive a warning that IIS cannot verify access to path (D:\DEV). Don’t worry about this for the time being.
Under “Host name”, enter a DNS path to your site (e.g., “dev.test-site.com”). Click “OK”.
Configure Application Pools for Installation
In IIS Manager, double-click the server instance in the left-hand pane. Click on “Application Pools” to display the list of server application pools in the center pane.
In the “Actions” pane on the right-hand side, click “Set Application Pool Defaults”.
Change “Enable 32-Bit Applications” - the second item from the top – from “False” to “True”, and then click “OK”. NOTE: if you skip this step, Coldfusion will not properly create the required mappings during the install. We will change this setting back after the installation completes – more on this later.
Modify the application.host.config File for 64-Bitness
Click: Start > Programs > Accessories. Right-click “Notepad” and choose “Run as administrator”.
Open the config file from within Notepad – default location: C:\Windows\System32\inetsrv\config\applicationHost.config
Do a search and change this one line from:
<add name="PasswordExpiryModule" image="C:\Windows\system32\RpcProxy\RpcProxy.dll" />
To this:
<add name="PasswordExpiryModule" image="C:\Windows\system32\RpcProxy\RpcProxy.dll" preCondition="bitness64" />
Restart the IIS Admin service.
Set HTTP Compression
According to some threads I read, the http compression module can cause errors if you don’t disable it globally. To remedy this, perform the following:
Click: Start > Programs > Accessories. Right-click “Command Prompt” and choose “Run as administrator”.
At the command prompt, change directory to intetsrv by typing: cd inetsrv
Run the following command:
C:\Windows\system32\inetsrv>appcmd.exe set config -section:system.webServer/httpCompression /-[name='xpress']
This will turn off HTTP compression for all sites in IIS.
In IIS Manager, double-click the server instance in the left-hand pane. Double-click the “Compression” icon in the IIS section of the center pane.
Uncheck all of the boxes, then click the “Apply” button under Actions in the right-hand pane.
Recheck all of the boxes, then click the “Apply” button under Actions in the right-hand pane.
Restart the IIS Admin service. This should enable compression and coldfusion to work at the same time.
NOTE: if for some reason you need to reverse this, run the following command from the command prompt:
C:\Windows\system32\inetsrv\appcmd.exe set config -section:system.webServer/httpCompression /+[name='xpress',doStaticCompression='false',dll='%windir%\system32\inetsrv\suscomp.dll']
INSTALLATION TASKS
Download the 64-bit installation package from Adobe – filename: coldfusion-801-wind64.exe.
Right-click the file and select “Run as administrator”.
Accept the terms of the License Agreement.
If you have an Enterprise license, enter it. For our purposes, just click the “Developer Edition” checkbox.
Select “Server configuration” – the default radio button.
I deselected all subcomponents and can’t guarantee that you’ll arrive at the same results if you select additional items like “.NET Integrated Services”. It should be fine, particularly if you install documentation. My preference was to keep the install as plain vanilla as possible.
Select the directory path for Coldfusion to install into – default is :C\Coldfusion
THE NEXT TWO STEPS ARE CRITICAL TO YOUR SUCCESS. Unselect “All IIS Websites” and select the “Configure specific IIS Website or another web server” radio button. Click “Add”, and then select your test Web site (e.g., “test-site”) under “IIS Web Site”. Hit “OK”.
Do NOT use the default directory path for the CF Administrator location (e.g., default path: “C:\inetpub\wwwroot”). Instead, point the installer to your new DEV root Web directory (e.g., “D:\DEV”). The bottom line, you want the installer to place the CFIDE directory and files within this folder, alongside your other CFML files and folders.
Enter an Administrator password.
Choose to Enable RDS, or not. I enable this by preference but it is not required. This allows you to make updates to files using a CFML editor directly vs. having to move/FTP the files over if you’re working remotely. Opponents to this argue that it’s potentially less secure, but for a lower environment I don’t see this as a major concern.
Confirm everything to kick off the install.
If all goes well you should see a message at the end stating that the install was successful. I recommend you uncheck the box that asks you to open the CF Administrator in the default Web browser after the install. NOTE: we will open it a different way during the post-installation tasks. The worst thing that will happen if you forget to uncheck the box is that you might receive an error that the command prompt hung – not a big deal – just close it and move on to the next (final) steps.
POST-INSTALLATION TASKS
Verify CF Installation:
The installation will create a new folder in your program group: Start > Programs > Adobe > Coldfusion 8. The default “Administrator” link will not work because it points to the wrong path: http://127.0.0.1/CFIDE/administrator/index.cfm. The “127.0.0.1” or “localhost” path as you may recall in IIS, points by default to the “C:\inetpub\wwwroot” directory. Our CFIDE files, however, are located within: D:\DEV.
To bring up the CF Administrator logon page, open up a Web browser and replace the “http://127.0.0.1” part of the path with the DNS path name to your CF environment (e.g., http://dev.test-site.com/CFIDE/administrator/index.cfm).
This should bring up the Coldfusion Administrator Login screen. Enter in the Administrator password you created during the install to log in and configure your application server.
Verify that your test-site renders correctly by typing in your test URL into a Web browser (e.g., http://dev.test-site.com).
Fix Application Pool Defaults to Re-enable SBS Web Applications:
At this point, Coldfusion Administrator and your test CMFL Web site should be working properly. The problem is, default SBS Web applications like OWA, RWW and Companyweb will throw errors and fail to start. Fortunately, this is easily remedied by performing the following steps:
In IIS Manager, double-click the server instance in the left-hand pane. Click on “Application Pools” to display the list of server application pools in the center pane.
In the “Actions” pane on the right-hand side, click “Set Application Pool Defaults”.
Change “Enable 32-Bit Applications” - the second item from the top – from “True” to “False” this time. This should re-enable the SBS applications, which would otherwise result in 500 errors (e.g., OWA, RWW, Companyweb, etc.). There is no need to restart IIS.
Open a Web browser and test that you can once again connect to OWA, RWW and Companyweb successfully.
In IIS click to highlight the application pool for your new site (e.g., “test-site”). In the right-hand pane, click “Advanced Settings”. Ensure that “Enable 32-Bit Applications” – second item from the top – is set to “True” for this application pool specifically.
Lastly, jump up and down for joy! Hopefully now, everything is working. Best of luck!! ..Paul D (MCP).

First, it would be a good idea for you to specify what distro of Linux you're using, as not all are supported by Adobe.
Second, this is probably your problem right here:
http://askubuntu.com/questions/40416/why-is-lib-libc-so-6-missing
In a nutshell, CF expects the 32-bit version of libc.so.6 to be in /lib, but it's probably not. You might be able to modify the installer to point to the correct location for that file, or you might be able to create a symlink to the file - but as the above link describes, creating a symlink might have negative consequences.
As for installing CF 8 64-bit, that's only available with Enterprise, not Standard. If you want CF Standard 64-bit, you need to upgrade to CF 9.
Dave Watts, CTO, Fig Leaf Software

How to install Windows 7/Vista as 2nd OS and retain predesktop environment (service partition)

This is a step-by-step instruction how to install Windows Vista or Windows 7 as a second OS on a Lenovo Thinkpad that originally shipped with Windows XP AND how to retain the access to the Lenovo Service Partition.
I have been searching the internet for instructions like these but could not find anything useful. So I am posting it
here. Maybe this helps other users.
I have tested the procedure below with installation of Windows Vista Ultimate (64bit) and Windows 7 Ultimate (64bit). I believe that the procedure will also work with the 32bit versions of these OSs. I am not totally convinced that this works when the OS to install is Windows XP (64bit or 32bit). XP has a completely different boot sequence compared to Vista or 7. The basic steps would remain the same, but the XP setup is less forgiving when it finds an unknown partition. If somebody wants to try it out, please post your results as a reply to this forum entry.
Never never never try to install an older OS (like Windows 2000 or NT) as a second OS when XP is already installed! This is doomed to fail.
The procedure below does NOT work for Linux installations. I am not a Linux wizard, but any Linux bootmanager I know about is incompatible with the Lenovo Service Partition.
The procedure was tested on a Thinkpad R61 model 8918-B9G. It should work similar on other models.
You definitely need a service partition with Rescue&Recovery version 4. It will NOT work with older versions of R&R or if the service partition is not a type12 partition (see below how to find out about that).
I assume that the harddisk partitions are unmodified, i.e. still have factory settings. This is likely the case if you
never attempted any OS install or recovery action. If this is not the case, the procedure may or may not work.
You also need a bootable CD with a tool that can change the size of your current system partition. I was using gparted live version 0.5.2-9. ( http://gparted.sourceforge.net/ )
Everything you do is at your own risk. I am in no way related to Lenovo, other than being a customer using their
products.
Step 1) Make a full backup of your harddisk. Get yourself recovery CDs for your Thinkpad model if you don't have any. The changes we are about to make can completely screw up your harddrive. A typo is sufficient for that to happen.
Step 2) Power on the system. Check that you can boot into the Service Partition by pressing the Thinkvantage button when the startup screen appears. (Older systems may have a differently named button.) If there is a problem booting the service partition now, it is likely that the rest of this procedure will not fix it.
Step 3) From the service partition choose 'Warmstart' to reboot the system. Reboot Windows XP, logon.
Open a command prompt. CD to the following directory:
\Program Files\Common Files\Lenovo\BMGR
On a german language system (like mine) it is
\Programme\Gemeinsame Dateien\Lenovo\BMGR
If you have an older IBM system the directory may be named
\Program Files\Common Files\IBM\BMGR
or something like that. Maybe you need to search around.
In the following, I will call this the "BMGR dir".
Enter the following command:
bmgr32 /info /v
You should get an output similar to this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
It's a Lenovo MBR
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? (512) Label is SERVICEV
Using version 2.05 of Lenovo Boot Manager
Reading: \\.\PHYSICALDRIVE0
        MBR Sector 1 Index: 1   Checksum: 00    Disabled
        MBR Sector 2 Index: 4   Checksum: 03    Passed
        MBR Sector 3 Index: 5   Checksum: FD    Passed
        MBR Sector 4 Index: 6   Checksum: 58    Passed
        MBR Sector 5 Index: 7   Checksum: 96    Passed
        MBR Sector 6 Index: 8   Checksum: 7F    Passed
        Data Sector Index: 3   Checksum: F1    Passed
        Original MBR Index: 2   Checksum: BD    Passed
        No Patch Sectors
        Checksum Byte: 00
        Think Flag: 1
        WinPE Partition (0-3): 1        Alt Boot Partition (0-3): 1
        Boot Config: 2 (Service Partition containing two Service OS's)
        Boot State: 0                   Alt Boot Flag: 0
        (Normal booting operation, will boot to Customer OS)
        RRU: 00000000 00000000          Prev Active Part: 255
        Previous Partition Type: FF     Patch IN: 0     OUT: 0
        CIRT Disabled
        TOC: 0000000000000000           Lock: 0
        Show Error: 0                   Halt on Error: 0
        CIRT Load Return: 0
        CIRT Execute Return: 0
        Pause Duration: 10              Scan Code: 0085
        F11 Msg: To boot to the Rescue and Recovery Environment, Press F11
        Check Msg: There has been a signature failure
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   239 255 255           63    301296177
1   0x00   0x12      0 193 255   239 255 255    301296240     11279520
2   0x00   0x00      0   0   0     0   0   0            0            0
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
The important thing to look for is the 0x12 partition type in the partition table at the bottom. This is the service
partition. If you do not have a 0x12 partition, then you can stop here because the rest of the procedure will not work
for you.
Step 4) Shutdown and boot gparted from CD. Shrink the system partition to the desired size. Do NOT touch the service partition! Do NOT attempt to create another partition! Leave the new white space on the disk untouched! Apply changes and restart the system.
Step 5) Reboot XP. gparted has set the NTFS dirty bit. This will cause XP to run a full CHKDSK. Depending on how much files there are on the partition this may take considerable time. Let CHKDSK run to completion. When CHKDSK finishes, the system will automatically reboot.
Step 6) XP reboots now. Logon. When loading the desktop, XP will show a popup window, stating that system settings have been changed and new devices been discovered and that the system should be rebooted. This is ok. XP actually recognized the shrunk system partition and applied the necessary changes to its own system parameters. Click YES to reboot the system.
Step 7) XP reboots. Logon. Open a command prompt, CD to the BMGR dir and enter:
bmgr32 /info /v
The output you get should be similar to the output you have seen in step 3, except that the partition 0 size column
shows a smaller value.
Step 8) Shutdown, restart. Check that you can still access the service partition by pressing the blue Thinkvantage button when the system startup screen appears.
Step 9) From the predesktop environment choose warmstart. Reboot XP. Logon, logoff, shutdown.
DO NOT SKIP THIS STEP!!! If you start the Windows Vista/7 install right after shutting down from the predesktop
environment, the Win Vista/7 setup program will screw up your harddisk! The Lenovo MBR bootmgr reboot takes two steps for completion. The first step is the shutdown and the second step is executed when booting from harddisk. A boot from the Windows CD will skip this second step and disaster finds its way...
Step 10) Insert the Windows Vista/7 DVD and boot it. Start the setup. Choose "Custom (advanced)" install. It will show the partitions on the disk. Select the white space (unallocated). Click on "disk options (advanced)". Click on "New" to create a new partition in the white space. Keep the default size, click "Apply". Click "Format". A popup window appears stating that the partition may hold OEM data. Continue. Click "Next". Installation starts.
Continued in the second post...

Step 11) Win Vista/XP will reboot several times during installation. You will always see the Windows bootmanager with an entry for "Earlier Windows version" and "Windows Vista/7". DO NOT DARE to touch the blue Thinkvantage button on any reboot or press any function keys!
Step 12) When the installation is finished, check that you can successfully reboot Win Vista/7 by selecting it from the Windows bootmanager.
Step 13) Reboot XP by choosing "Earlier Windows version" from the Windows bootmanager. Open a command prompt. CD to the BMGR dir. Enter the following command:
bmgr32 /info /v
The output will now look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
Opened Master Boot Record to see whose MBR it is.
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   254 255 255           63    109675692
1   0x00   0x07    239 255 255   239 255 255    109676544    191619072
2   0x00   0x12    239 255 255   239 255 255    301296240     11279520
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
startLBA and size will of course differ, depending on the actual partition sizes you have set. Note that Windows setup moved the service partition to entry 2 of the partition table. If you do not see the 0x12 partition then stop here.
Otherwise the following step will likely screw up you harddisk.
Enter the following command (case sensitive?):
bmgr32 /Fbootmgr.bin /m0 /IBM /v
The output will look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /Fbootmgr.bin /m0 /IBM /v
installing MBR
finding free sectors
Sector 9 is free
Sector 10 is free
Sector 11 is free
Sector 12 is free
Sector 13 is free
Sector 14 is free
Sector 15 is free
Sector 16 is free
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
Setting Think bit
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
This command reinstalled the Lenovo bootmanager in the MBR that was erased by the Win Vista/7 setup program.
Enter the following command:
bmgr32 /info /v
The output will now look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
It's a Lenovo MBR
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
Using version 2.05 of Lenovo Boot Manager
Reading: \\.\PHYSICALDRIVE0
        MBR Sector 1 Index: 1   Checksum: 00    Disabled
        MBR Sector 2 Index: 11 Checksum: 03    Passed
        MBR Sector 3 Index: 12 Checksum: FD    Passed
        MBR Sector 4 Index: 13 Checksum: 58    Passed
        MBR Sector 5 Index: 14 Checksum: 96    Passed
        MBR Sector 6 Index: 15 Checksum: 7F    Passed
        Data Sector Index: 10 Checksum: 01    Passed
        Original MBR Index: 9   Checksum: 12    Passed
        No Patch Sectors
        Checksum Byte: 00
        Think Flag: 1
        WinPE Partition (0-3): 2        Alt Boot Partition (0-3): 2
        Boot Config: 0 (Service Partition containing one Service OS)
        Boot State: 0                   Alt Boot Flag: 0
        (Normal booting operation, will boot to Customer OS)
        RRU: 00000000 00000000          Prev Active Part: 255
        Previous Partition Type: FF     Patch IN: 0     OUT: 0
        CIRT Disabled
        TOC: 0000000000000000           Lock: 0
        Show Error: 0                   Halt on Error: 0
        CIRT Load Return: 0
        CIRT Execute Return: 0
        Pause Duration: 10              Scan Code: 0085
        F11 Msg: To boot to the Rescue and Recovery Environment, Press F11
        Check Msg: There has been a signature failure
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   254 255 255           63    109675692
1   0x00   0x07    239 255 255   239 255 255    109676544    191619072
2   0x00   0x12    239 255 255   239 255 255    301296240     11279520
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
So you have actually regained the Lenovo bootmanager. But you are not done yet.
Step 14) Shutdown. Restart the system. DO NOT PRESS THE BLUE THINKVANTAGE BUTTON AT THE SYSTEM STARTUP SCREEN!!! IT DOES NOT WORK YET! When the system startup screen DISAPPEARS, quickly press F11 (maybe several times). The system should now boot the predesktop environment from the service partition.
Step 15) When the predesktop is there, choose "warmstart". When the system startup screen appears, press the blue Thinkvantage button. The system should again boot into the predesktop. The blue Thinkvantage button now works permanently.
Step 16) Check that you can boot Win XP and Win Vista/7 from the Windows bootmanager. You're done!

How to install ovi suite to a drive other than C:?...

how to install ovi suite to a drive other than c:??? my c: drive is almost full with other partitions perfectly free to install it, how do i do that? can i use previous versions of ovi suite to use with my e63? at this point, i'm unable to use ovi suite at all, because there's no room to install it on my c: drive.
allllllllso there's one more thing, when i originally had tried installing ovi suite on my computer i had more than 1gb free. after installing it i on'ly had 500mb free. i had only intended for it to use a very small amount of space, and since i also use my c: drive for virtual memory i quickly uninstalled it, looking for an option i'd maybe skipped over while installing it the first time. no luck. anyways, when i looked in the add/remove programs control panel the installed size of ovi suite was only 40-50mb. even after uninstalling ovi suite the extra memory space that seemed to all of a sudden taken up by the installation stayed used.
when looking at the file sizes of everything on my hard drive, (including system files and paging file) there is still a descreprency between the amount of memory used and the size of all files total on the drive. at this point im quite disgusted and disapointed in ovi suite as i'm mostly unable to use it to connect my phone to my computer and i'm also having problems with the CA101 cable as well. i guess i'll have to go check for another cable.
nokia!!! wake up and fix yo **bleep**!!!!
anyone have any solutions for the main problem? (installing to a drive other than c? is there support for this option in any of the new beta versions? can that be included in the newest betas? i'm suuuuuure i'm not the only one begging for this option!!!

Hi ostrenga4, sorry to hear about your experiences.
When installing Nokia Ovi Suite to PC, Windows makes "system restoration points", which are available to restore operating system to previous condition, if something goes wrong, for example in driver installation.
You can change install location of Nokia Ovi Suite with following:
- Download Nokia Ovi Suite install package from Nokia Ovi Suite pages
- Start Windows Command prompt
- From Command prompt, navigate to folder containing Nokia Ovi Suite install package, which you downloaded
- Start Nokia Ovi Suite install package with command line "Nokia_Ovi_Suite_webinstaller.exe /TARGET="D:\TestDir\Test"
- This results, that Nokia Ovi Suite installer creates folder D:\TestDir\Test (if that doesn't exist) and installs Nokia Ovi Suite there.
- Unfortunately, Windows Installer still keeps installer cache files and system restoration points in C: drive (or whatever your system drive is)
As you can see, this is possible, but it is very much recommend to have enough space for installing software into system drive.
Cheers, Samuli

How to install Windows on a SATA boot drive

Here is how to install Windows XP on a SATA boot drive. This procedure was first developed by syar2003 and has been used by many iusers ncluding myself. Although it was originally developed for Neo2 mb's and Windows XP Pro, it has general applicability to systems as well.
1. Have only the SATA drive you want to be the boot drive active in your system. Disconnect the power to all other HDD's if any.
2. Have only one optical drive active. Disconnect the power to the other opticals if any. (Best to have a burner optical as master on IDE1.)
3. Plug SATA drive into SATA 1 on the mb. (it may show us as an IDE drive somewhere down the list in BIOS. That's okl)
4. Enable appropriate SATA options in BIOS. Set boot order to floppy, cd, SATA drive. Set boot priority to SATA drive.
5. Partition and format the SATA HDD using the utilites CD that came with the SATA drive. (If you don't have an HDD utilities disk, download one from the website of your HDD manufacturer.)
6. Run Windows setup. No need to load drivers at the F6 promt unless you are planning to do a RAID configuration.
7. Windows XP should install without incident.
8. After you are up and running, plug the power back into your other HDD and optical drives if any.
If you have a board older than the K8 series, it may be necessary to load the SATA drivers at the F6 prompt. If the above procedure does not work, than try it again loading the SATA drivers.
If this procedure does not work for you, it is likely that your particular SATA HDD has some compatablity problem with Windows setup and/or your motherboard. The solution to this is to try another SATA drive. In general, most failures using this procedure have been traced to certain WD, Seagate and Hitachi SATA drivers of smaller capacities. Fewer problems seem to have occured with Maxtor HDD's.

Kaplan, from an earlier post of mine regarding sata2 hdds - I have them plugged into the sata1&2 ports, installed the nvidia raid first and then installed winxp (in both raid 0 and raid 1). My bios is 3.1 and its a known problem that bios 3.3 & 3.4 have nvidia raid problems but seems to be fixed in the beta bios 3.53:
I just purchased 2 hitachi deskstar sata2 80gb hdds ($60 each at zzf) and the interesting thing about them is that you have to "enable" sata2. I have been testing the performance of sata1, sata2, raid1 and raid0 and the results are below.
The drives themselves are factory default set at sata1. Since I purchased OEM, no software or instructions were included. I had to go to the hitachi website download section to download a dos based program (the features program) to enable sata2. After enabling the hdds to sata2, they were recognized in winxp in the nforce ADMA controller device driver and the screen reads with the primary channel as Serial ATA Generation 2 - 3G...and all 4 boxes below it are checked (the boxes enable bios select xfer mode, enable read caching, enable write caching and enable command queuing are checked). An interesting thing about the sata2 spec is that all sata2 hdds must come standard with NCQ...its not advertised on these 80 gb hdds on the hitachi website (unlike the larger hitachi sata2 hdds) but its a standard sata2 spec and these 80gb hitachi hdds are recoginized in winxp as sata2.
The other interesting feature about the hitachi sata2 hdds is setting them up to operate in an adjustable "performance" to "silence" mode. The hdds are default set at high perfromance but you can manually lower the performance to increase the silence of the hdds which is fully adjustable to your liking. I tested the highest silence/lowest performance setting and you cannot hear the hard drive at all.
Testing - I tested the 2 hitachi sata2 deskstars with the first result in sata1 mode, the second in sata2 mode, the third in raid1 mode and the fourth in raid0 mode.
First, a significant increase in raid0 over sata1, sata2 and raid1 with sequential reads and writes (PC Wizard).
Write: 28mb/s vs 29mb/s vs 27mb/s vs 53mb/s
Read: 45mb/s vs 46mb/s vs 43mb/s vs 83mb/s
Second, significant increase in sata 2, raid 1 & raid 0 over sata1 with buffered reads and writes (PC Wizard).
Write: 104mb/s vs 176mb/s vs 165mb/s vs 266mb/s
Read: 123mb/s vs 200mb/s vs 200mb/s vs 293mb/s
Third, significant increase in sata 2, raid 1 & raid 0 over sata1 with burst reads (HD Tach).
Burst Read: 133mb/s vs 225mb/s vs 219mb/s vs 334 mb/s
It is interesting to note that raid1 is better than sata1 but marginally slower in all tests over sata2. Raid0 is significantly faster on all tests.

How to install OS 9.2 on G4 PowerBook 15" 1.67GHz

The installation disks come with the laptop didn't include OS 9.2. But I need it for one program. Where can I get it?

Hi, agliu -
Welcome to Apple's Discussions.
The only source for Classic (OS 9) on that model is the set of disks that originally came with it, although it may not be obvious how to install it.
One or more of these Apple KBase articles may help -
Article #151871 - Mac OS X 10.3: Installing Classic
Article #301408 - Using Restore discs with computers that ship w/ OSX 10.3.7 or later
Article #86775 - Install Mac OS 9 to Use Classic Applications

How to install Classic on 800MHz SD eMac w/10.4 w/o wiping entire drive??

I've been trying to help out a friend who bought an 800MHz eMac (SuperDrive) used on Craigslist. Machine is in great condition and came with Tiger installed and working fine. She has since installed many of her own OS X apps, but finds she needs to run a few legacy apps and needs Classic installed.
She has a 4-CD set of eMac Software Restore discs, which contain OS 10.1.4 plus OS 9.2.2. These are not standalone installers, however. After mounting Disc 1, she is able to reboot from that CD (into an OS 9 interface), but is only presented with a single option, and that is to erase the hard disk and do a complete restore of the original OSes and apps that shipped with the computer. Since she has spent weeks installing apps and configuring the computer just as she wants it, she does not want to have to wipe the entire drive just to be able to add Classic at this point.
I can think of two alternatives, neither of which will work for her because she does not have access to an external firewire drive, either with or without a bootable system on it. My two methods would be to either:
A. Boot from an external FW drive in target disk mode and then use a standalone OS 9 installer (which she does have) to get Classic on the eMac;
B. Clone the entire hard drive to an external drive and then run the 4 eMac Software Restore discs, update to the latest version of Tiger, and then add back all her additional installed apps and utilities, etc.
1) Am I correct in assuming that method A would, in fact, work?
More importantly, though, can anyone suggest a simpler way to install OS 9 on this machine which would not involve using an external drive? It's so frustrating that the Software Restore disc is bootable (whereas the standalone OS 9 installer disc is not!)...yet there is no apparent way to access just the OS 9 installer on these Restore discs and to run just that installer and not have to reformat the entire drive.
2) Any bright ideas on a relatively simple workaround would be greatly appreciated!
Additionally, it is unknown whether or not OS 9 drivers have been installed on this eMac. I assume, though, that if they had not been installed, then an OS 9 installation would balk and not go through. It would be worth taking that chance, though, as the worst that could happen is that OS 9 would not install. Then there would be no other option but to do a full erase and install from the Restore Discs.
3) Is there any way of ascertaining in advance whether or not OS 9 drivers have been installed?
Thanks in advance for any help!
PowerMac G4/867 Mac OS X (10.3.9)

Your initial post notes that OS X 10.4 is installed but 10.1.4 is on the actual restore discs that you have. My recollection is that Apple switched from 10.1.4 to 10.2 late in the production run of the 700 MHz model eMac (specificaly, they upgraded two weeks after I bought my 700 MHz eMac), so a 800 MHz model should have shipped with OS X 10.2, not 10.1.4. There are significant differences in the Restore disc sets between the different OS X versions. In any case it's clear that the discs you have do not include a retail Tiger install disc. You'll eventually want to pick up the retail black-lable Tiger 10.4 Install DVD in case it's ever necessary to reinstall the OS (if the eMac is one that doesn't have a DVD-ROM or DVD-RW drive, the Tiger DVD can still be exchanged for a set of CDs for a nominal fee).
From your later posts, it appears that you do have a separate OS 9 install CD but that the emac won't boot from that OS 9 disc. It rather sounds as if the disc set you have is actually from an earlier 700 MHz eMac model. Open System Profiler and check the video hardware; if it shows ATI graphics rather than nVidia graphics, you definitely have the wrong set of discs. While there's no online link for this, you can call the Apple Store and ask about purchasing a replacement set of discs for the Mac model you actually have (have the info from eMac: How to locate the serial number and identify your model handy if you call).
The OS 9 installation method you need depends on the set of restore disks and the original OS X version that was provided with those discs. Since you have 10.4 installed on a 800 MHz eMac, you'd nominally start with Mac OS X 10.4: Restoring applications from a Mac OS X 10.2 Software Restore disc rather than the older Using Restore Discs with Mac OS X 10.2 through 10.3.3. Unfortunately, reinstalling Classic following that guide does invovlve erasing the HD, which you want to avoid.
Given the discs you do have is for 10.1.4, you can check the later part of Using Apple Software Restore to install or reinstall parts without erasing (Mac OS X 10.1.5 or earlier) for the steps on how to install parts without erasing. However, if I'm picturing the correct set of Restore discs that you have in hand (there have been enogh different sets of resstore and install discs to make that a royally confusing morass), OS 9 is not on the Restore disc set in versions prior to OS X 10.2; rather, there should be a separate OS 9 Install CD in the set of discs that came with OS X 10.1.4 Macs.
Under the circumstances, unless you acquire the correct Restore discs for that model eMac, your best chance of getting Classic installed would on first thought be to take up Chopsuey's suggestion about dragging the OS 9 System Folder from the OS 9 Install CD onto the eMac's HD, then try to use that to get a hobbled form of Classic open well enough to use Tome Viewer to extract the full OS 9 System onto the HD. Although the OS 9 CD you have from a OS X 10.1.4 disc set would be for an nVidia graphics eMac and your appears to be an ATI model, the actual graphics hardware is driven by OS X, so having the wrong graphics drivers in OS 9 may or may not actually limit Classsic to running in a 640x480 pixel window.
I'm pretty sure you'd find it easier to call the Apple Store for the correct set of Restore discs for that model.
Installing the OS 9 drivers on the hard drive is required to boot the nVidia graphic model eMacs into OS 9 from the HD but is not required to use the OS 9 System Folder to run Classic. Later ATI graphics eMacs won't boot into OS 9 regardless of whether or not the drivers are installed on the hard drive. Either way, if you only want to run Classic, you don't need to reformat the drive to install the OS 9 drivers (nor search for the Terminal hack to put OS 9 drivers onto an already-formatted HD).

How to install mac OS on a blank HD

Just bought a new (2012) mac mini and the hard drive is blank.
I don't own any other mac's so I'm lost about how to install an OS.
What do I need to do and No, it didn't come with any discs.

Have you tried this yet:
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
If you are able to successfully boot to the Recovery HD, then:
Install or Reinstall Lion from Scratch
If possible backup your files to an external drive or second internal drive.
Erase the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Erase tab in the DU main window.
Set the format type to Mac OS Extended (Journaled.) Click on the Erase button and wait until the process has completed.
Quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Install button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

How to install original win8 os in hp pavillion dmv i5 laptop

Similar Messages

Maybe you are looking for