How to install second Ethernet-adapter

I've got Ultra 5 and there is the on-board Ethernet-adapter on it. But i want to insert another (PRO/100) PCI adapter.
I did it, and ptrconf says:
pci (driver not attached)
ethernet (driver not attched)
I tried sys-unconfig - but this utility always trying to configure my ON-BOARD card... So, how to install drivers?
Thank you.

I've got Ultra 5 and there is the on-board
Ethernet-adapter on it. But i want to insert another
(PRO/100) PCI adapter.
I did it, and ptrconf says:
pci (driver not attached)
ethernet (driver not attched)
I tried sys-unconfig - but this utility always trying
to configure my ON-BOARD card... So, how to install
drivers?
Thank you.

Similar Messages

How to install ODI Planning Adapter

Hi Friends,
One of my client is trying to install the ODI Planning Adapter. After unzip of the file we have two folders: Drivers and impexp. I recall that we are supposed to copy the contents of these folders somewhere but I cannot find documentation and what I should do.
Can anyone suggest on how to instal planning adapter.I searched for documentation in odiap_93110_readme.pdf I don't see instruction on how to install the ODI planning adapter.
If anyone can give me a step by step procedure to instal planning adapter it would be great help.
Regards.

Hi All,
I am new to oracle BI space . i need to load data from my flat file source to hyperion planning 9.3.0.1 application.
Here are the steps i followed:
downloaded and installed ODI 10.1.3.4.
i could find the adpater for hyperion planning 9.3.0.1 for ODI.
Can somebody please help me out and tell me where the above mentioned installation file is located in internet.please share the location...
Some how or the other i could able to find the odiap_93110.pdf file which lets me to know about installation instructions.
Thanks & Regards,
Lokesh

How to install SOAP Axis adapter and where is it available ??

Hi,
I heard that SOAP Axis adapter was not initially available for PI 7.0 and was introduced in some later support pack.When I checked the below url I found that some of the components are missing.
http://xi-dev.intranet.com:50000/XIAxisAdapter/MessageServlet
Can anyone please suggest how I can get that pack and where it will be available?
How to install it?
Thanks
Deepthi.

Hi Sunil,
Dont mind...one final question, they mentioned in the README file as below..
// Open the SDA archive using some unzip tool and replace the following empty
jar files with the those inclued in Axis 1.4 src package
axis.jar
commons-discovery-0.2.jar
commons-logging-1.0.4.jar
commons-net-1.0.0-dev.jar
wsdl4j-1.5.1.jar
When i checked in the Axis folder, I found so many files.
Do I need to just add this Axis zip file into aii_af_axisprovider.sda Archive file.?
If possible, It would be very helpful if you send the aii_af_axisprovider.sda file which you have deployed into your system?
Thanks
Deepthi

Instaling second ethernet card / sharing internet connection

Hiya.
Is it possible to share my cable broadband service ( PS3 etc ) through my PPC G4, maybe by installing a second ethernet pci card and sharing the internal ethernet, or is there any other possibilities. no airport, but do have a D-link bluetooth dongle...

As other posters have pointed out, you don't need a second ethernet card to share out your connection - if you have an existing router (with a number of ethernet connections), you can connect your game consoles to that, and your ISP will be none the wiser. Your ISP will still give you one IP address; your router does the translation into multiple private IP addresses (eg 10.0.1.1, 10.0.1.2, etc)
Another option is to buy an inexpensive network switch, put that between the router and the Mac, connect the other devices to the switch, and turn on sharing from ethernet to ethernet. But you really don't need to with a router on the network.
If you share out your Mac's internet connection, the devices behind the connection will get IP addresses in the range 192.168.2.x (the Mac will effectively be their router/DHCP server at 192.168.2.1).
Matt

How to install second hard drive in Satellite A200-1BW?

I see my new Satellite A200-1BW has two hard drive bays,on looking into the second bay I cannot see how a second drive can be fitted as the plug in socket appears to be missing.
What parts do i need to fit to fit a second drive as they are held in stock by my local computer outlet and are quite cheap,can anybody advise me on part numbers etc of the bits I need.
Thanks
Steve

Hi,
there are many different models of your machine on the market and some of them have a second drive, some of them not. If you bought a model with one drive then you will only be able to install ONE drive because your model was only intended to have one drive.
And even if you solder a connector to it or attach it in any other way then you dont know if the bios supports the second drive.
My suggestion on it: obtain a USB-HDD and store your data on that drive. Would be making more sense then spending a lot of time on investigation to find out that your mainboard is not able to handle a second drive.
Cheers

How to install custom Resource Adapter

Hi I have writen the java class for the Custome Resource adapter and I loaded the .class file into web-inf classes folder.I followed the installation steps given in the deployement document.In that I am not understanding one step i.e "Install .class file and help file into IDM" How can we do this and How to get the particular resource under Managed Resources tabe of Configure tab./its very urgent for me any kind of help is appriciable.

Ok, since it is urgent, do it the way Sun/Waveset inserts the adapters.
1.) Alter your java code to have
package com.waveset.adapter;
As your package line.
2.) Compile the adapter to a class file.
3.) Grab the idm.jar file from $WSHOME/WEB-INF/lib and copy it to e.g /tmp
4.) unjar it. jar -vxf idm.jar
5.) copy the your adapter class file to /tmp/com/waveset/adapter
6.) jar the archive. jar -cvf idm.jar /tmp/com
7.) Make a backup of the original idm.jar, and copy the new to the old position replacing the old jar-file. Bounce your app-server.
8.) Log in as configurator or an administrator with equal capabilities. And add the custom adapter using the previous procedure... although, use the adaper class path
com.waveset.adapter.YourCustomAdapter
9.) Go to debug pages and put tracing on the same class file, and tail -f the app-server std out.
10.) try to configure the adapter. Note any eventual error messages. Post error messages on the forum along with the std out log.
If your adapter code works, it should work... if not your problems are elsewhere.
Please not that this set up is not recommended for production environment and if you apply service packs etc this fix will break!

How to install Microsoft Loopback Adapter

I want to install the Microsoft Lookback Adapter in Windows 7. I have done this under Vista either via:
1) Control Panel, Classic View, Add Hardware
2) Device Manager, right click on root node and select Add Legacy Hardware
I can't find the equivalent under Windows 7 - any suggestions?
Thanks!

I have a video that covers the steps to install the Microsoft Loopback Adapter in Windows 7. Hope this helps...
http://www.youtube.com/watch?v=R9674zGHxrE
Guides and tutorials, visit
ITGeared.com.

How to install second copy (different serial #) on desktop

I have aperture 2 with same serial number installed on both my laptop and desktop on our network. Only one copy can be worked on at the same time so I bought a new copy so my husband and I can work on images at the same time. How do I install a new copy with a different serial number on the desktop and have the images on the old copy transferred onto the new copy? Will the new copy delete the old or will I now have 2 apertures on the desktop? I don't want to lose any of the images and only want the new copy with a different serial number on the desktop.
thanks

You've got a couple options and I ran into a similar issue when installing and running a demo for Aperture 2 while not wanting to replacing my purchased copy of 1.5 until I purchase version 2.
Firstly, why don't you just install one version to each computer? You can have multiple Aperture Libraries on a single computer if you really want to keep your photos completely separate from your husbands but then you can just have separate project folders within the same libraries. You can add metadata to your images when you import them so attaching your name to the images at that time will maintain who shot what. This way makes updating the software much easier and hassle free. Which is not the case when running two copies of the same program on the same hardware.
Another option if you must install more than one copy of Aperture to each computer is to rename the currently installed version of Aperture and then install the new one. This gives you two copies of the same program but you'll run into problems when the next update is released. The renamed version will not be recognized by Software Update because it'll be looking for the version simply called, "Aperture" in the applications library. There is a fairly simple workaround for this though.
Instead of renaming the original install, move it into a new location or subfolder in the Applications folder. Then install the new copy and when an update is released it will be taken care of for the copy installed directly in the Applications folder. Once that update is complete, switch the two so that the other copy is now in the Applications folder and the updated one is in the sub-folder. Run Software Update again and it should run the update to the other copy without a problem.
I would recommend installing just one copy to each computer with the separate serials and just setup your own libraries onto each computer. Through a network you can share libraries between the two systems and you wont run into any problems with running the software or updating it.
I hope this helps you out with your problem.

How to install Trust bluetooth adapter 4.0 on my HP Pavillion p6-2304eb

I have tried several times to install, but after installing, PC (windows 8.1) doesn't recognize my adapter???
message: plug in the adapter
The bluetooth adapter is a TRUST bluetooth adapter 4.0 with productnumber 18187.
plugged in a USB 3.0.
This question was solved.
View Solution.

Trust has not supplied a driver for Windows 8.1 so the issue is not with your PC or the operating system. Tyr plugging it into a usb 2.0 port. USB 3.0 ports are picky about devices.
The problem is that the bluetooth dongle has no support for Windows 8.1. Contact Trust .
Sorry to bear bad news. I would return the dongle and find one that suports Windows 8.1.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Satellite A350-122 - How to install second HDD?

Hello,
I'm a french owner of a A350-122 (Serial No: 39169719K)
In the french user's manual, on page 1-5, it's written that it's possible to insert an other hard drive, and on page 2-6 the rear view of the A350-122 shows a second location on the left for a second hard drive.
So, I have bought an Intel X25-M SSD to put in the second location. I have opened the second location and there is nothing: no sata connector, no power connector, only an empty location.
So, what's wrong with this Satellite A350-122?
Thank's for your answer.

Hi,
here is the official link for the french user manual of the A350 : http://support1.toshiba-tro.de/tedd-files2/0/userman-fr-20081024130641.zip
- On page 1-5 you will see in french as Information : "Il est possible d'insrer des disques durs supplmentaires".
If you translate these words with Google for example, it means : "It is possible to add additional hard disks".
- On page 2-6 you will see a picture of the rear with of the laptop and on the left, in red, it's written : "Disque dur 2".
If you translate these words with Google for example, it means : "Hard Disk 2".
I have contacted the customer service by phone, they admit there is a problem and the will find a friendly solution...
Chtilainlain.
ps : I'm not the only one with this question, if you search in this forum , you'll find this : http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=182934&#182934

How to install Oracle AS JMS Adapter on Websphere (or any J2EE server)

Hi,
We have a requirement in which the client wants to connect to the OC4J JMS running in SOA Suite (Oracle Application Server 10.1.3.4).
They are using Websphere. We are exploring ways by which they can connect from Websphere application to Oracle AS OC4J JMS.
One option is - deploy the Oracle AS JMS adapter in Websphere and then use it to connect to the OC4J JMS.
Please let us know if this is the right approach. Also, if so, kindly point to the documentation regarding how to install the JMS adapter on 3rd party J2EE servers such as websphere.
Rgds,
Amit

While searching the knowledge base I found the following note, which seems to suggest that Oracle Adapters are not deployble on other J2EE application servers:
Support For Jca Adapter In Other Application Servers Like Jboss [ID 1114738.1]
==============================================
From the statements in documentation it may be implied that jca adapter should be deployable on any application server that is compliant with j2ee/jca. Please note that this cannot be implied at this time and jca adapter cannot be deployed on other application servers than OAS in BRM 731 due to some technical constraints. So currently we can support only OAS and not JBoss or another application server , in BRM 731. The documentation will be updated accordingly to reflect this.

VPN server does not work when a second network adapter is enabled

I have an Xserve providing DNS, filesharing, and VPN services on an office LAN. The server sits behind a gateway router and is set as a DMZ host.
VPN has been working absoluely flawlessly on the server for some time. However, I've recently discovered that this all changes when the Xserve's second ethernet adapter is enabled.
To illustrate:
en0: static IP 192.168.2.250
en1: disabled
VPN works perfectly
en0: static IP 192.168.2.250
en1: static IP 192.168.2.251
DNS settings unchanged, DMZ host unchanged
VPN doesn't work
The above is even true when attempting to connect internally.
VPN is configured for L2TP, and when the second NIC is connected the VPN server logs the following (below). There are a number of other users of Lion Server users that seem to be experiencing the same log pattern, but there doesn't seem to be a definitive solution.
I was wondering if anyone has any advice on how I could solve this problem? Is it possible to bind the VPN server to a specified network adapter?
Thanks in advance for any help or ideas.
(And to preempt the question of "why do you need to use both NICs", the two interfaces are to be used for load balancing. See https://discussions.apple.com/message/17655599?ac_cid=142432)
Wed Feb 22 15:53:53 2012 : Directory Services Authentication plugin initialized
Wed Feb 22 15:53:53 2012 : Directory Services Authorization plugin initialized
Wed Feb 22 15:53:53 2012 : L2TP incoming call in progress from 'xxx.xxx.xxx.xxx'...
Wed Feb 22 15:53:53 2012 : L2TP received SCCRQ
Wed Feb 22 15:53:53 2012 : L2TP sent SCCRP
2012-02-22 15:53:54 GMT          Incoming call... Address given to client = 192.168.2.229
Wed Feb 22 15:53:54 2012 : Directory Services Authentication plugin initialized
Wed Feb 22 15:53:54 2012 : Directory Services Authorization plugin initialized
Wed Feb 22 15:53:54 2012 : L2TP incoming call in progress from 'xxx.xxx.xxx.xxx'...
Wed Feb 22 15:53:54 2012 : L2TP received SCCRQ
Wed Feb 22 15:53:54 2012 : L2TP sent SCCRP
2012-02-22 15:53:56 GMT          Incoming call... Address given to client = 192.168.2.220
Wed Feb 22 15:53:56 2012 : Directory Services Authentication plugin initialized
Wed Feb 22 15:53:56 2012 : Directory Services Authorization plugin initialized
Wed Feb 22 15:53:56 2012 : L2TP incoming call in progress from 'xxx.xxx.xxx.xxx'...
Wed Feb 22 15:53:56 2012 : L2TP received SCCRQ
Wed Feb 22 15:53:56 2012 : L2TP sent SCCRP
2012-02-22 15:54:00 GMT          Incoming call... Address given to client = 192.168.2.221
Wed Feb 22 15:54:00 2012 : Directory Services Authentication plugin initialized
Wed Feb 22 15:54:00 2012 : Directory Services Authorization plugin initialized
Wed Feb 22 15:54:00 2012 : L2TP incoming call in progress from 'xxx.xxx.xxx.xxx'...
Wed Feb 22 15:54:00 2012 : L2TP received SCCRQ
Wed Feb 22 15:54:00 2012 : L2TP sent SCCRP
2012-02-22 15:54:04 GMT          Incoming call... Address given to client = 192.168.2.222
Wed Feb 22 15:54:04 2012 : Directory Services Authentication plugin initialized
Wed Feb 22 15:54:04 2012 : Directory Services Authorization plugin initialized
Wed Feb 22 15:54:04 2012 : L2TP incoming call in progress from 'xxx.xxx.xxx.xxx'...
Wed Feb 22 15:54:04 2012 : L2TP received SCCRQ
Wed Feb 22 15:54:04 2012 : L2TP sent SCCRP
2012-02-22 15:54:08 GMT          Incoming call... Address given to client = 192.168.2.226
Wed Feb 22 15:54:08 2012 : Directory Services Authentication plugin initialized
Wed Feb 22 15:54:08 2012 : Directory Services Authorization plugin initialized
Wed Feb 22 15:54:08 2012 : L2TP incoming call in progress from 'xxx.xxx.xxx.xxx'...
Wed Feb 22 15:54:08 2012 : L2TP received SCCRQ
Wed Feb 22 15:54:08 2012 : L2TP sent SCCRP
2012-02-22 15:54:12 GMT          Incoming call... Address given to client = 192.168.2.223
Wed Feb 22 15:54:12 2012 : Directory Services Authentication plugin initialized
Wed Feb 22 15:54:12 2012 : Directory Services Authorization plugin initialized
Wed Feb 22 15:54:12 2012 : L2TP incoming call in progress from 'xxx.xxx.xxx.xxx'...
Wed Feb 22 15:54:12 2012 : L2TP received SCCRQ
Wed Feb 22 15:54:12 2012 : L2TP sent SCCRP
2012-02-22 15:54:13 GMT             --> Client with address = 192.168.2.228 has hungup
2012-02-22 15:54:14 GMT             --> Client with address = 192.168.2.229 has hungup
2012-02-22 15:54:16 GMT             --> Client with address = 192.168.2.220 has hungup
2012-02-22 15:54:20 GMT             --> Client with address = 192.168.2.221 has hungup
2012-02-22 15:54:24 GMT             --> Client with address = 192.168.2.222 has hungup
2012-02-22 15:54:28 GMT             --> Client with address = 192.168.2.226 has hungup
2012-02-22 15:54:32 GMT             --> Client with address = 192.168.2.223 has hungup

Try switching the order of the services in System Preferences > Network.
Put the second one at the top.
HTH,
b.

I have an airbook, 10.7.4 LION, thunderbolt ethernet adapter and when trying to install 1.2.1 thunderbolt upgrade it says "this software not supported on this system"? Any advice on how to get the adapter to work?

I have a new airbook, 10.7.4 LION, thunderbolt ethernet adapter and when trying to install 1.2.1 thunderbolt upgrade it says "this software not supported on this system"? Any advice on how to get the adapter to work?

Welcome to Apple Support Communities
If you purchased the computer before 2010, your computer hasn't got Thunderbolt, so you can't use it

How do I install my thunderbolt to ethernet adapter on OS X Yosemite?

I recently bought a thunderbolt to ethernet adapter for my Macbook Pro. I found that accessing the server is quicker when I have a hard connection. However, when I pull up my system preferences and network connections, my thunderbolt connection will come up but the settings do not properly connect and even when I try to manually connect it, I am unable to connect. Help! Does anyone have any ideas on how to address this issue/resolve it?
Please let me know, thanks!

Hello John,
Welcome to Apple Support Communities.
The article linked below provides information which should help you resolve the issue setting up your Thunderbolt to Ethernet Adapter on your MacBook Pro.
Apple USB or Thunderbolt to Ethernet Adapters: First time setup - Apple Support
Ciao,
-Jason

How to use thunderbolt to gigabit ethernet adapter

hi mates. i just purchase the Thunderbolt to Gigabit Ethernet Adapter last week for my Mac Book Pro Retina. but i have no idea how it work. i tried just plug in the adapter and the LAN cable in but no luck...
Any idea how it works?

Plug in the Adapter and the cable to the adapter and the other end of the cable to a switch or router then Reboot the system. Then check the Network section in System Preferences to see if the Ethernet shows up. If it does your done. If not then you have a bad adapter, a bad cable, both bad adapter and cable or the Thunderbolt port is bad.
Or at the last a corrupted install of OS X.

How to install second Ethernet-adapter

Similar Messages

Maybe you are looking for