How to install Windows XP on a single SATA drive?

I am trying without much success to use a single Maxtor 200 GB SATA drive in a non-RAID configuration running Windows XP Home SP 2+. I obtained documentation from the MSI Download site that explains how to do such a thing. However ...
First, out of the box the Drivers & Utilities CD is useless -- can't read it, simply hangs the CD drive.
Second, the drivers from the Download site (IATA_ICH5R) return "incompatible hardware. software not supported on this chipset" messages.
So where do I get the drivers required to install Windows XP on a single SATA drive (to use at point F6 in the Windows XP installation)?
Regards,
Bob (ll1951md)
P.S. Configuration ...
865PE/G Neo2-P (MS-6728) w/ Intel Extreme Graphics 2, Realtek ALC655 Audio
2 GB Corsair Dual Channel DDR Memory
Intel P4 3.0e GHz Processor
1 Maxtor 200 GB SATA HD
1 HDS 120 GB ATA HD

Thanks for the tips. I was able to install Windows XP and boot from the SATA drive by using these options and setting the appropriate boot device selections...
Legacy Mode
ATA Configuration - PATA only
SATA Keep enabled - yes
PATA Keep enabled - yes
PATA channel selection - both
Combined Mode Option - S-ATA 1st Channel
S-ATA Ports Definition - P0 - 3rd./P1 - 4th.
I just wasn't sure if I was really getting "SATA" performance, etc. without specific drivers.
Thanks again.
Bob (ll1951md)

Similar Messages

How to install windows 8 onto an external hard drive connected with usb 2.0?

How to install windows 8 onto an external hard drive connected with usb 2.0?

Transfer win 8 from inside hd to external hd.
Cloning Win 8 is also OK.
Aomei Backupper can do the above.
In additional, Do you know Windows to Go?
http://www.disk-partition.com/features/windows-to-go-creator.html

How to install windows 7 in bootcamp from flash drive os x 10.9.1

How to install windows 7 in bootcamp from flash drive os x 10.9.1

oooHideooo wrote:
It DOESN'T WORK!!
I tried tonnes of method already, and the apple guide method absolutely doesn't work for MacBook Air, 10.9.1
Did you even tried it yourself????!! with Maverick 10.9.1 you will NOT be able to get pass the bootcamp first page:"install window 7". It will give an error msg saying "The installer disc could not be found"
My usb confirmed bootable! I created it with bootcamp, and tested it on a different macbook and it works. But doesn't work on MacBook Air. (Even startup disk doesn't detect it as bootable in Air)
anyone else has a real solution to this problem?
Thousands have successfully tried it themselves and installed Windows on a Macbook Air. Perhaps if you provided some details about what you did and what errors you observed we could help you. The Boot Camp instaructions, if followed, will produce a successful install.

How to install Windows XP on a new hard drive in desktop computer

Have a Lenovo desktop. I replaced the defective hard drive. Obtained Windows XP installation disks from Lenovo. I received recovery two
Recovery CDs, namely Rescue and Recovery CD and Product Recovery CD along with 5 CD Roms ( 1of 5 through 5of 5).
I want to install Windows XP in my new Hitachi hard drive. Should I use only the 5 CD ROMS 1 thru 5, leaving out the Recovery and Rescue CD
and Product Recovery CD Rom.
How to I install Window XP in my new hard drive? I am not a computer
wizard. As a retired IBM senior citizen I need some help from the community. I am not cognizant with the steps to follow. I am a new
member of this great community.
Thanks a bunch ! padman
personal informations removed for your own security

padman215, welcome to the forum,
you need to boot from the Rescue and Recovery cd and select to recover the system and then to recover to factory state. It will then eventually ask for the other discs.
Please be sure that you read the messages carefully; if it asks for a supplementary disc, (which you don't seem to have), you need to click on "no" should it ask for one - this throws alot of people.
Happy installing
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

How do install Windows 7 from a USB optical drive?

I have a 27" 2013 iMac with no optical drive so I borrowed an Apple USB portable optical drive. How do I install Windows on BootCamp from the USB Optical drive?

iirc, you won't be able to or at least you shouldn't, it will take much longer than using a usb install
CHECKLIST
use only a +8gb USB2 flash drive
disconnect ALL devices except kb, mouse
STEPS
do a PRAM reset
open disk utility, confirm you have 1 partition (‘mac HD’ unless you renamed it) and repair permissions TWICE
dl a windows ISO
insert your usb flash drive and open boot camp assistant, choose all options making sure you used the new ISO just dl'd
if you get an error that the windows support software is unavailable, manually dl it here, put it on a separate USB2 drive and install by clicking setup.exe after windows is installed
http://support.apple.com/kb/ht5634
w7 ISOs
http://techverse.net/download-windows-7-iso-x86-x64-microsofts-official-servers/

TS4517 How to install windows in mac without a CD Drive

So i got an iMac but it has no cd drive at the side iMac and i can't get my windows installed using the CD i bought anyone has any clue to what i should do?

Start Boot Camp Assistant and follow the instructions in the installation guide, or, follow the instructions for your computer here http://www.apple.com/support/bootcamp/

How to install 2 oracle homes on singl windows host

Hi Experts,
I am planning to install two sap R/3 4.7 ext200 SR1 instances on windows 2003. I already installed DEV instance & planning for QAS.
I am confused about how to install two ORACLE softwares on single windows host.
I search on internet there for windows they are pointing to the registry value
\HKEY_LOCAL_MACHINE
Software\Oracle\inst_loc.
I am not able to understand what I have to do with this ?
Can you please help me to understand & execute this.
Thanks,
Sachin

Sachin,
Go throuth this link to understand more about Oracle Inventory and Oracle Homes software update.
http://cs.ifmo.ru/~ad/Documentation/oracle-10g-lib-doc/em.101/b12140/3_oui_oracle_homes.htm#i1005634
The current entry is picked from the PATH vairable of the system and user that you have logged on. This is because you have already done 1 Oracle Installation on the host.
Keep in mind that you choose the correct oracle home while installing and in future updating Oracle software (patchset, Interim Pactches...)
You can give a seperate path for Oracle Inventory. Just go thru to the existing folder of OraInventory in Program files you will understand it better.
It is used to install and update the Oracle software in the oracle home that you will choose in your next step.
All the Best,
Nilesh

How to install Windows 8.1 with Windows 8 Product key?

I have purchased Upgrade pack from Windows 7 to Windows 8. I have also Updated the OS to windows 8.1 through Store. How to install Windows 8.1 with Windows 8 Product key?

The download link for the Windows 8.1 installer at the Upgrade with Product Key Only does not accept a Windows 8.0 product key. I ended up using the trick suggested by Andre Ziegler in this thread to obtain the 8.1 download independent of the Windows
Store, but I haven't yet checked if the 8.0 key works from 8.1 Setup.
I do IT for a living but I have plenty of family members that bring their notebook PCs to me and ask me to do the heavy lifting, and I'd rather not re-download the same 3.6 GB every single time someone tells me to fix their PC. I also want to be able to
re-install 8.1 from the source media in case of a catastrophic hard disk failure and I have to replace the disk.
As an aside, tools that retrieve product keys for installed products end up retrieving the 8.0 product key from an 8.1 install that was upgraded via the Store. It kind-of makes sense that an 8.0 key could work to install 8.1 because 8.1 is supposed
to be a free upgrade for licensed 8.0 users, but this doesn't seem to work until after 8.1 is successfully installed via some trickery and the user supplies the 8.0 key to activate it.

How to install windows on the SSD (Y580)

I have bought an Y580 recently wIth a 64GB SSD and 1TB HDD. I asked the salesperson upfront if the OS would be on the SSD. He said yes. Turns out that it is not. When i returned to them they told me it's a hybrid drive solution. And they have no idea how to install Windows on the SSD.
I did some research and found out that Lenovo uses *Rapiddrive* to speed up programs. Hence why i can't see the SSD in WIndows as it is merged with the 1TB HDD. In Disk management 2 disks show , 0 and 1 , but Windows asks to give disk 1 a MBR or GPT (this is apparantly due to the rapiddrive methode).
My questions:
* Is it possible to install Windows on the SSD and if so how can that be done without loosing the backup on the hidden partition of the 1TB disk? (so that OKR still works)
* What are the benefits of Rapiddrive over using the SSD as bootdisk?

Since it is a hybrid drive, it works a little bit differently; Lenovo's "Rapiddrive" is also different from other hybrids, and in the sake of making it "user friendly" and seen as a single disc they have probably nerfed some configurability for the intermediate/advanced users. However, Windows should already be installed on the SSD portion of the drive, this should be done automatically according to this press release:
http://shop.lenovo.com/us/sitelets/ee/consumer-news
"In the factory we will preload not just Windows 7 on the SSD, but also our Lenovo applications like OneKey™ Theater or OneKey™ Rescue System. The applications, operating system, drivers and other files are all fully-optimized for Enhanced Experience to make them load much faster. This, combined with their installation on the SSD will make the boot time to Windows desktop even faster. Some portion of the SSD will also be reserved as the Windows Paging File — this is used by Windows as 'virtual memory' additional to the normal RAM installed inside the computer. With the SSD acting as the Paging File, general Windows 7 performance will also benefit, especially when multitasking several applications.
The remaining space, which will typically be around 15GB on a 32GB SSD, will be empty, ready for the user to install their favorite applications and files."
I have some of the fastest SSD's around installed on my desktops (SATA III), and while they are blazing fast, keep in mind the whole boot sequence still isn't going to be instantaneous even with an SSD (the biggest differennce you will notice is by the time Windows is loaded, it's fully loaded to the RAM, whereas a normal HDD you may see the desktop but your PC will still be cranking away with startup processes). If your startup is taking 30 seconds or less, maybe even a little longer, it's probably accessing the SSD just fine; if it's taking closer to 60 seconds, then yeah it may need to be reinstalled/reconfigured.
As for reinstalling, sorry I won't really be able to help, hopefully someone else can come along; I personally have never used OKR anyways, and aside from doing a ghost backup I wouldn't say for sure that OKR would be salvageable with a fresh install. And because the Rapiddrive is its own technology, half SATA half PCI-E, I also couldn't tell you if it's even possible to fully seperate the two and keep them as distinct drives.

How to install Windows 7/Vista as 2nd OS and retain predesktop environment (service partition)

This is a step-by-step instruction how to install Windows Vista or Windows 7 as a second OS on a Lenovo Thinkpad that originally shipped with Windows XP AND how to retain the access to the Lenovo Service Partition.
I have been searching the internet for instructions like these but could not find anything useful. So I am posting it
here. Maybe this helps other users.
I have tested the procedure below with installation of Windows Vista Ultimate (64bit) and Windows 7 Ultimate (64bit). I believe that the procedure will also work with the 32bit versions of these OSs. I am not totally convinced that this works when the OS to install is Windows XP (64bit or 32bit). XP has a completely different boot sequence compared to Vista or 7. The basic steps would remain the same, but the XP setup is less forgiving when it finds an unknown partition. If somebody wants to try it out, please post your results as a reply to this forum entry.
Never never never try to install an older OS (like Windows 2000 or NT) as a second OS when XP is already installed! This is doomed to fail.
The procedure below does NOT work for Linux installations. I am not a Linux wizard, but any Linux bootmanager I know about is incompatible with the Lenovo Service Partition.
The procedure was tested on a Thinkpad R61 model 8918-B9G. It should work similar on other models.
You definitely need a service partition with Rescue&Recovery version 4. It will NOT work with older versions of R&R or if the service partition is not a type12 partition (see below how to find out about that).
I assume that the harddisk partitions are unmodified, i.e. still have factory settings. This is likely the case if you
never attempted any OS install or recovery action. If this is not the case, the procedure may or may not work.
You also need a bootable CD with a tool that can change the size of your current system partition. I was using gparted live version 0.5.2-9. ( http://gparted.sourceforge.net/ )
Everything you do is at your own risk. I am in no way related to Lenovo, other than being a customer using their
products.
Step 1) Make a full backup of your harddisk. Get yourself recovery CDs for your Thinkpad model if you don't have any. The changes we are about to make can completely screw up your harddrive. A typo is sufficient for that to happen.
Step 2) Power on the system. Check that you can boot into the Service Partition by pressing the Thinkvantage button when the startup screen appears. (Older systems may have a differently named button.) If there is a problem booting the service partition now, it is likely that the rest of this procedure will not fix it.
Step 3) From the service partition choose 'Warmstart' to reboot the system. Reboot Windows XP, logon.
Open a command prompt. CD to the following directory:
\Program Files\Common Files\Lenovo\BMGR
On a german language system (like mine) it is
\Programme\Gemeinsame Dateien\Lenovo\BMGR
If you have an older IBM system the directory may be named
\Program Files\Common Files\IBM\BMGR
or something like that. Maybe you need to search around.
In the following, I will call this the "BMGR dir".
Enter the following command:
bmgr32 /info /v
You should get an output similar to this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
It's a Lenovo MBR
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? (512) Label is SERVICEV
Using version 2.05 of Lenovo Boot Manager
Reading: \\.\PHYSICALDRIVE0
        MBR Sector 1 Index: 1   Checksum: 00    Disabled
        MBR Sector 2 Index: 4   Checksum: 03    Passed
        MBR Sector 3 Index: 5   Checksum: FD    Passed
        MBR Sector 4 Index: 6   Checksum: 58    Passed
        MBR Sector 5 Index: 7   Checksum: 96    Passed
        MBR Sector 6 Index: 8   Checksum: 7F    Passed
        Data Sector Index: 3   Checksum: F1    Passed
        Original MBR Index: 2   Checksum: BD    Passed
        No Patch Sectors
        Checksum Byte: 00
        Think Flag: 1
        WinPE Partition (0-3): 1        Alt Boot Partition (0-3): 1
        Boot Config: 2 (Service Partition containing two Service OS's)
        Boot State: 0                   Alt Boot Flag: 0
        (Normal booting operation, will boot to Customer OS)
        RRU: 00000000 00000000          Prev Active Part: 255
        Previous Partition Type: FF     Patch IN: 0     OUT: 0
        CIRT Disabled
        TOC: 0000000000000000           Lock: 0
        Show Error: 0                   Halt on Error: 0
        CIRT Load Return: 0
        CIRT Execute Return: 0
        Pause Duration: 10              Scan Code: 0085
        F11 Msg: To boot to the Rescue and Recovery Environment, Press F11
        Check Msg: There has been a signature failure
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   239 255 255           63    301296177
1   0x00   0x12      0 193 255   239 255 255    301296240     11279520
2   0x00   0x00      0   0   0     0   0   0            0            0
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
The important thing to look for is the 0x12 partition type in the partition table at the bottom. This is the service
partition. If you do not have a 0x12 partition, then you can stop here because the rest of the procedure will not work
for you.
Step 4) Shutdown and boot gparted from CD. Shrink the system partition to the desired size. Do NOT touch the service partition! Do NOT attempt to create another partition! Leave the new white space on the disk untouched! Apply changes and restart the system.
Step 5) Reboot XP. gparted has set the NTFS dirty bit. This will cause XP to run a full CHKDSK. Depending on how much files there are on the partition this may take considerable time. Let CHKDSK run to completion. When CHKDSK finishes, the system will automatically reboot.
Step 6) XP reboots now. Logon. When loading the desktop, XP will show a popup window, stating that system settings have been changed and new devices been discovered and that the system should be rebooted. This is ok. XP actually recognized the shrunk system partition and applied the necessary changes to its own system parameters. Click YES to reboot the system.
Step 7) XP reboots. Logon. Open a command prompt, CD to the BMGR dir and enter:
bmgr32 /info /v
The output you get should be similar to the output you have seen in step 3, except that the partition 0 size column
shows a smaller value.
Step 8) Shutdown, restart. Check that you can still access the service partition by pressing the blue Thinkvantage button when the system startup screen appears.
Step 9) From the predesktop environment choose warmstart. Reboot XP. Logon, logoff, shutdown.
DO NOT SKIP THIS STEP!!! If you start the Windows Vista/7 install right after shutting down from the predesktop
environment, the Win Vista/7 setup program will screw up your harddisk! The Lenovo MBR bootmgr reboot takes two steps for completion. The first step is the shutdown and the second step is executed when booting from harddisk. A boot from the Windows CD will skip this second step and disaster finds its way...
Step 10) Insert the Windows Vista/7 DVD and boot it. Start the setup. Choose "Custom (advanced)" install. It will show the partitions on the disk. Select the white space (unallocated). Click on "disk options (advanced)". Click on "New" to create a new partition in the white space. Keep the default size, click "Apply". Click "Format". A popup window appears stating that the partition may hold OEM data. Continue. Click "Next". Installation starts.
Continued in the second post...

Step 11) Win Vista/XP will reboot several times during installation. You will always see the Windows bootmanager with an entry for "Earlier Windows version" and "Windows Vista/7". DO NOT DARE to touch the blue Thinkvantage button on any reboot or press any function keys!
Step 12) When the installation is finished, check that you can successfully reboot Win Vista/7 by selecting it from the Windows bootmanager.
Step 13) Reboot XP by choosing "Earlier Windows version" from the Windows bootmanager. Open a command prompt. CD to the BMGR dir. Enter the following command:
bmgr32 /info /v
The output will now look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
Opened Master Boot Record to see whose MBR it is.
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   254 255 255           63    109675692
1   0x00   0x07    239 255 255   239 255 255    109676544    191619072
2   0x00   0x12    239 255 255   239 255 255    301296240     11279520
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
startLBA and size will of course differ, depending on the actual partition sizes you have set. Note that Windows setup moved the service partition to entry 2 of the partition table. If you do not see the 0x12 partition then stop here.
Otherwise the following step will likely screw up you harddisk.
Enter the following command (case sensitive?):
bmgr32 /Fbootmgr.bin /m0 /IBM /v
The output will look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /Fbootmgr.bin /m0 /IBM /v
installing MBR
finding free sectors
Sector 9 is free
Sector 10 is free
Sector 11 is free
Sector 12 is free
Sector 13 is free
Sector 14 is free
Sector 15 is free
Sector 16 is free
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
Setting Think bit
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
This command reinstalled the Lenovo bootmanager in the MBR that was erased by the Win Vista/7 setup program.
Enter the following command:
bmgr32 /info /v
The output will now look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
It's a Lenovo MBR
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
Using version 2.05 of Lenovo Boot Manager
Reading: \\.\PHYSICALDRIVE0
        MBR Sector 1 Index: 1   Checksum: 00    Disabled
        MBR Sector 2 Index: 11 Checksum: 03    Passed
        MBR Sector 3 Index: 12 Checksum: FD    Passed
        MBR Sector 4 Index: 13 Checksum: 58    Passed
        MBR Sector 5 Index: 14 Checksum: 96    Passed
        MBR Sector 6 Index: 15 Checksum: 7F    Passed
        Data Sector Index: 10 Checksum: 01    Passed
        Original MBR Index: 9   Checksum: 12    Passed
        No Patch Sectors
        Checksum Byte: 00
        Think Flag: 1
        WinPE Partition (0-3): 2        Alt Boot Partition (0-3): 2
        Boot Config: 0 (Service Partition containing one Service OS)
        Boot State: 0                   Alt Boot Flag: 0
        (Normal booting operation, will boot to Customer OS)
        RRU: 00000000 00000000          Prev Active Part: 255
        Previous Partition Type: FF     Patch IN: 0     OUT: 0
        CIRT Disabled
        TOC: 0000000000000000           Lock: 0
        Show Error: 0                   Halt on Error: 0
        CIRT Load Return: 0
        CIRT Execute Return: 0
        Pause Duration: 10              Scan Code: 0085
        F11 Msg: To boot to the Rescue and Recovery Environment, Press F11
        Check Msg: There has been a signature failure
# active type      start CHS      end CHS      startLBA       size
0   0x80   0x07      1   1   0   254 255 255           63    109675692
1   0x00   0x07    239 255 255   239 255 255    109676544    191619072
2   0x00   0x12    239 255 255   239 255 255    301296240     11279520
3   0x00   0x00      0   0   0     0   0   0            0            0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
So you have actually regained the Lenovo bootmanager. But you are not done yet.
Step 14) Shutdown. Restart the system. DO NOT PRESS THE BLUE THINKVANTAGE BUTTON AT THE SYSTEM STARTUP SCREEN!!! IT DOES NOT WORK YET! When the system startup screen DISAPPEARS, quickly press F11 (maybe several times). The system should now boot the predesktop environment from the service partition.
Step 15) When the predesktop is there, choose "warmstart". When the system startup screen appears, press the blue Thinkvantage button. The system should again boot into the predesktop. The blue Thinkvantage button now works permanently.
Step 16) Check that you can boot Win XP and Win Vista/7 from the Windows bootmanager. You're done!

How to install Windows 8.1 Pro on Macbook Pro

Hello everyone,
I'm new to these forums and new to bootcamping as well but have been reading all kinds of posts about how to install Windows 8.1 on their Macs using bootcamp. I am however having trouble with this situation as I have no clue what to do next. I have a Macbook Pro 2011, running on Maverics, and I recently downloaded a digital copy of Windows 8.1 Pro, 64-bit, for the Mac platform, along with its CD key through my University's hub website as can be seen here.
After finishing the downloading process, I received this file which is about 4GB large.
When i double click on the file this happens. It opens something on DEVICES which gives me what is on the 2nd image.
At this point, I'm at a loss on what to do next. Do i burn the file on a DVD hoping that Bootcamp will recognize it as a windows disc? Any help would be appreciated, thank you.

You need a 'Full' Installer.
From Boot Camp 5.1: Frequently asked questions - Apple Support
Which versions of Windows work with Boot Camp 5.1?
Boot Camp 5.1 supports 64-bit, non-Enterprise versions of Windows 7, Windows 8.0, and Windows 8.1. This version of Boot Camp doesn't support Windows XP, Windows Vista, or any 32-bit version of Windows. Depending on your Mac, you may be able to use an earlier version of Boot Camp to work with other versions of Windows. For details, see the Boot Camp system requirements for Microsoft Windows.
Can I perform an upgrade install from a 32-bit version of Windows to a 64-bit version of Windows?
It's not possible to upgrade a 32-bit version of Windows to a 64-bit version of Windows. Back up your important files, then perform a new install of the 64-bit version of Windows.

How to install windows 7 on my macbook pro mid 2009 using usb. right now aim using mavericks 10.9 can any one please help me. I tried to edit plist in boot camp but it went wrong please help me

how to install windows 7 on my macbook pro mid 2009 using usb. right now iam using mavericks 10.9 can any one please help me. I tried to edit plist in boot camp but it went wrong please help me.
Iam new to coding. please help me.

try the solution posted by kunu here and report back
https://discussions.apple.com/thread/5105056?tstart=0

How to install Windows 7 on a MacBook Air?

Hi everybody,
I am sorry in case this has been covered before, but i couldnt find anything searching different categgories here, so i´d appreciate some help.
I have got a late 2011 MacBook Air with lots of SSD and so on and i want to install windows 7.
I bought a wndows 7 OEM DVD (actually, two discs, one says support software)
I have tried to run bootcamp and follow the instructions, but to now end.
on my macbook air, i get the option "create a windows 7 disc" or something like that (the first option), which doesnt help me because i dont have optical drive
when i start boot camp on my iMac, this option will be greyed out.
Also, I have tried to to ISO copys of the windows DVD and save them to a USB stick but i just wouldnt come to any result.
does anybody have a good, comprehensive instruction on how to install windows 7 on an MBA withou optical drive?
Also, is 30GB OK for Win 7 if you basically dont wanna do to much in windows (no office etc, just some small clients)
thanks!

30GB is not enough, especially on an SSD. Normally 50-60GB and with SSD I'd go with 80-90GB.
http://www.apple.com/support/bootcamp faq, how to, special instructions for Air
There is a program to create DVD from ISO or .exe
Apple Boot CAmp Assistant should have prompted to save a driver for you to support a USB-DVD, in addition to the normal Apple B.C. drivers you save to flash card.
Disk Utility is not a good method for burning Windows DVDs.
http://simplyburns.en.softonic.com/mac
https://discussions.apple.com/thread/3241150

How to install windows 7 on Old Macbook Pro 15'inch 2.3 Core 2 Duo

How to install windows 7 on Old Macbook Pro 15'inch 2.3 Core 2 Duo:
I want to known how to install windows 7 on Old Macbook 15'inch 2.3 Core 2 Duo by using usb
I try many time, but after restart bootcamp partition, apple show blinking folder error
I think this firmware not support to install windows by usb
NOTE:
I Cannot install Apple New OSX Mountain Lion, Mavericks etc in this MAC
If I cannot install windows 7 on this MAC, so tell me what I will do with this MAC ?

I agree with the optical drive, mine acted strange, and i thought people were crazy and my drive was shot, but a simple cleaning disc worked miracles.
But- are you trying to reboot with both the USB install and the DVD install both plugged in? that would definitely cause confusion.
Do this, reboot with NOTHING plugged in. Once you hear the Mac chime, immediately press and hold option.
You should only see the Mac HD, and Recovery Partition.
THEN plug in your external DVD, and wait a min or two, you should see a disc icon appear next to the recovery partition that says something like windows. If that doesnt appear after a min or two, unplug it and put the USB stick and do the same thing. I had to do it this way on my mid 09 MBP.
Let me know if this works to start the install. If not we may have to start over with Bootcamp Assistant

I have Macbook Pro 13" mid 20012. How to install Windows 8 onto the mac using DVD? 10.8.3

the title says it all.
i have windows 8 DVD and i would like to have a clear instructions on how to install windows 8. I dont understand the need for USB

Welcome to the Apple Support Communities
You need a USB drive to install the Windows support software. It contains all the drivers that your MacBook Pro needs, and you will have to install them after finishing the Windows installation. If you don't install them, a lot of things won't work: the wireless card, the sound card, the brightness, the trackpad gestures... Apart from that, you don't need it for anything else.
Apple has released the official steps to install Windows 8 on a Mac, so if you want, print this PDF > http://manuals.info.apple.com/en_US/boot_camp_install-setup_10.8.pdf

How to install Windows XP on a single SATA drive?

Similar Messages

Maybe you are looking for