How to install windows xp over vista on a toshiba satellite A200 1YO
How to install raid/scsi drivers and get rid of vista for good
what you will need
â?¢ 1 USB external floppy drive
â?¢ 2 floppy disks
â?¢ 1 set of drivers for the hard drive you have in the computer
â?¢ a legal copy of windows xp pro
WHAT TO DO WITH THE FLOPPY DISKS
COPY THE DRIVERS DONT CUT AND PASTE THEM
â?¢ get DISK 1 and place the drivers required onto the disk as they are without any folders
â?¢ get DISK 2 and make a folder called $OEM$ and within that folder make another called TEXTMODE then within that folder insert the drivers that you have in disk 1
Installing the drivers and windows xp pro
â?¢ when windows asks you to press F6 to install raid drivers press F6
â?¢ then enter DISK1 into the floppy drive
â?¢ when it prompts you to press "s" to install...install the raid and storage controllers
â?¢ press "s" again and press enter on the same raid driver you just told windows to use
â?¢ windows will then say that it already has drivers for the raid controller
â?¢ press the appropriate key to tell windows you want it to use the floppy drivers instead of windows own
â?¢ after the drivers load remove the floppy disk
â?¢ wait until windows asks for the drivers again and insert DISK 2
â?¢ and windows will install at long last vista is GONE you will need the drivers for any hardware your computer system but they should be easy to get from the manufacturers web site
I have used this method and it worked with a Toshiba satellite a200 1yo laptop with no problems
PLEASE LEAVE COMMENTS ON HOW YOU GOT ON TO LET OTHERS KNOW THAT THIS METHOD WORKS THANKS
Message was edited by: tamwilson
How to install raid/scsi drivers and get rid of vista for good
what you will need
? 1 USB external floppy drive
? 2 floppy disks
? 1 set of drivers for the hard drive you have in the computer
? a legal copy of windows xp pro
WHAT TO DO WITH THE FLOPPY DISKS
COPY THE DRIVERS DONT CUT AND PASTE THEM
? get DISK 1 and place the drivers required onto the disk as they are without any folders
? get DISK 2 and make a folder called $OEM$ and within that folder make another called TEXTMODE then within that folder insert the drivers that you have in disk 1
Installing the drivers and windows xp pro
? when windows asks you to press F6 to install raid drivers press F6
? then enter DISK1 into the floppy drive
? when it prompts you to press "s" to install...install the raid and storage controllers
? press "s" again and press enter on the same raid driver you just told windows to use
? windows will then say that it already has drivers for the raid controller
? press the appropriate key to tell windows you want it to use the floppy drivers instead of windows own
? after the drivers load remove the floppy disk
? wait until windows asks for the drivers again and insert DISK 2
? and windows will install at long last vista is GONE you will need the drivers for any hardware your computer system but they should be easy to get from the manufacturers web site
I have used this method and it worked with a Toshiba satellite a200 1yo laptop with no problems
Similar Messages
-
How to install windows 7 over windows 8 HP 2000- 2b16NR
So, I purchased this laptop at a pawn shop a couple of years ago, and it has served me pretty well up until now. After the latest windows update, something went terribly, terribly, wrong. For some unknown reason I am now stuck with Windows 8.1 Evaluation with the license expired, which means it shuts itself down EVERY hour. I'm done with this, I hate the Windows 8 interface anyway, now its time to go back to something I know and love. I've read up on a lot of these posts, and joined the forums only because I did not see another post that was in direct relation to my own model number. If someone could please guide me through the process of installing Windows 7 from a disk, it would be ever so helpful. If you could also post a link pointing me in the right direction for all the drivers specific to my computer, that would be awesome as well, since I'm no techie, and really don't know a whole lot about this sort of thing outside of basic knowledge. Thanks in advance for the help!
I got my hands on a bootable copy of Windows 7. Everything loads up just fine until I make the settings to US English etc, and click install, when I do that I get this error message: "The product key does not match any of the Windows images availible for installation. Enter a different product key." Which doesn't make any sense to me, because since I've had this computer everything has updated just fine, and worked great up until this stupid update to 8.1. That being said, when I go into other options and select 'Reset my PC' I get another error message: "Unable to reset your PC. A required driver partition is missing." I've seen on some other posts where having the drive partitioned in the right way (format I guess?) is another issue with installing Windows 7 over 8. If this indeed another source of the problem, how do I go about fixing it?
-
How to install Windows 7 over corrupt Windows XP
Hello,I have a MSI U 100 wind Netbook with Windows XP. I suddenly get this Mistake: Windows could not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM
I would like to install Windows 7 Home 32 bit now. Can I just install it over my corrupt Windows XP?
Thank you.......
GaleHi,
Regarding the error messages Windows could not start because the following file is missing or corrupt: \WINDOWS\SYSTEM32\CONFIG\SYSTEM, please take a look at the below KB article:
How to recover from a corrupted registry that prevents Windows XP from starting
For install Windows 7 Home 32 bit on your computer, we need to make sure the hardware is compatible with the new OS, and the manufacturer get the available drivers to have the devices work well with the new operating system. We could take use of
Windows 7 Upgrade Advisor.
More information, please take a look at the following article:
Upgrading from Windows XP to Windows 7
Upgrading to Windows 7: frequently asked questions
Hope this helps
Best regards
Michael Shao
TechNet Community Support -
How to install Windows 7/Vista as 2nd OS and retain predesktop environment (service partition)
This is a step-by-step instruction how to install Windows Vista or Windows 7 as a second OS on a Lenovo Thinkpad that originally shipped with Windows XP AND how to retain the access to the Lenovo Service Partition.
I have been searching the internet for instructions like these but could not find anything useful. So I am posting it
here. Maybe this helps other users.
I have tested the procedure below with installation of Windows Vista Ultimate (64bit) and Windows 7 Ultimate (64bit). I believe that the procedure will also work with the 32bit versions of these OSs. I am not totally convinced that this works when the OS to install is Windows XP (64bit or 32bit). XP has a completely different boot sequence compared to Vista or 7. The basic steps would remain the same, but the XP setup is less forgiving when it finds an unknown partition. If somebody wants to try it out, please post your results as a reply to this forum entry.
Never never never try to install an older OS (like Windows 2000 or NT) as a second OS when XP is already installed! This is doomed to fail.
The procedure below does NOT work for Linux installations. I am not a Linux wizard, but any Linux bootmanager I know about is incompatible with the Lenovo Service Partition.
The procedure was tested on a Thinkpad R61 model 8918-B9G. It should work similar on other models.
You definitely need a service partition with Rescue&Recovery version 4. It will NOT work with older versions of R&R or if the service partition is not a type12 partition (see below how to find out about that).
I assume that the harddisk partitions are unmodified, i.e. still have factory settings. This is likely the case if you
never attempted any OS install or recovery action. If this is not the case, the procedure may or may not work.
You also need a bootable CD with a tool that can change the size of your current system partition. I was using gparted live version 0.5.2-9. ( http://gparted.sourceforge.net/ )
Everything you do is at your own risk. I am in no way related to Lenovo, other than being a customer using their
products.
Step 1) Make a full backup of your harddisk. Get yourself recovery CDs for your Thinkpad model if you don't have any. The changes we are about to make can completely screw up your harddrive. A typo is sufficient for that to happen.
Step 2) Power on the system. Check that you can boot into the Service Partition by pressing the Thinkvantage button when the startup screen appears. (Older systems may have a differently named button.) If there is a problem booting the service partition now, it is likely that the rest of this procedure will not fix it.
Step 3) From the service partition choose 'Warmstart' to reboot the system. Reboot Windows XP, logon.
Open a command prompt. CD to the following directory:
\Program Files\Common Files\Lenovo\BMGR
On a german language system (like mine) it is
\Programme\Gemeinsame Dateien\Lenovo\BMGR
If you have an older IBM system the directory may be named
\Program Files\Common Files\IBM\BMGR
or something like that. Maybe you need to search around.
In the following, I will call this the "BMGR dir".
Enter the following command:
bmgr32 /info /v
You should get an output similar to this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
It's a Lenovo MBR
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? (512) Label is SERVICEV
Using version 2.05 of Lenovo Boot Manager
Reading: \\.\PHYSICALDRIVE0
MBR Sector 1 Index: 1 Checksum: 00 Disabled
MBR Sector 2 Index: 4 Checksum: 03 Passed
MBR Sector 3 Index: 5 Checksum: FD Passed
MBR Sector 4 Index: 6 Checksum: 58 Passed
MBR Sector 5 Index: 7 Checksum: 96 Passed
MBR Sector 6 Index: 8 Checksum: 7F Passed
Data Sector Index: 3 Checksum: F1 Passed
Original MBR Index: 2 Checksum: BD Passed
No Patch Sectors
Checksum Byte: 00
Think Flag: 1
WinPE Partition (0-3): 1 Alt Boot Partition (0-3): 1
Boot Config: 2 (Service Partition containing two Service OS's)
Boot State: 0 Alt Boot Flag: 0
(Normal booting operation, will boot to Customer OS)
RRU: 00000000 00000000 Prev Active Part: 255
Previous Partition Type: FF Patch IN: 0 OUT: 0
CIRT Disabled
TOC: 0000000000000000 Lock: 0
Show Error: 0 Halt on Error: 0
CIRT Load Return: 0
CIRT Execute Return: 0
Pause Duration: 10 Scan Code: 0085
F11 Msg: To boot to the Rescue and Recovery Environment, Press F11
Check Msg: There has been a signature failure
# active type start CHS end CHS startLBA size
0 0x80 0x07 1 1 0 239 255 255 63 301296177
1 0x00 0x12 0 193 255 239 255 255 301296240 11279520
2 0x00 0x00 0 0 0 0 0 0 0 0
3 0x00 0x00 0 0 0 0 0 0 0 0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
The important thing to look for is the 0x12 partition type in the partition table at the bottom. This is the service
partition. If you do not have a 0x12 partition, then you can stop here because the rest of the procedure will not work
for you.
Step 4) Shutdown and boot gparted from CD. Shrink the system partition to the desired size. Do NOT touch the service partition! Do NOT attempt to create another partition! Leave the new white space on the disk untouched! Apply changes and restart the system.
Step 5) Reboot XP. gparted has set the NTFS dirty bit. This will cause XP to run a full CHKDSK. Depending on how much files there are on the partition this may take considerable time. Let CHKDSK run to completion. When CHKDSK finishes, the system will automatically reboot.
Step 6) XP reboots now. Logon. When loading the desktop, XP will show a popup window, stating that system settings have been changed and new devices been discovered and that the system should be rebooted. This is ok. XP actually recognized the shrunk system partition and applied the necessary changes to its own system parameters. Click YES to reboot the system.
Step 7) XP reboots. Logon. Open a command prompt, CD to the BMGR dir and enter:
bmgr32 /info /v
The output you get should be similar to the output you have seen in step 3, except that the partition 0 size column
shows a smaller value.
Step 8) Shutdown, restart. Check that you can still access the service partition by pressing the blue Thinkvantage button when the system startup screen appears.
Step 9) From the predesktop environment choose warmstart. Reboot XP. Logon, logoff, shutdown.
DO NOT SKIP THIS STEP!!! If you start the Windows Vista/7 install right after shutting down from the predesktop
environment, the Win Vista/7 setup program will screw up your harddisk! The Lenovo MBR bootmgr reboot takes two steps for completion. The first step is the shutdown and the second step is executed when booting from harddisk. A boot from the Windows CD will skip this second step and disaster finds its way...
Step 10) Insert the Windows Vista/7 DVD and boot it. Start the setup. Choose "Custom (advanced)" install. It will show the partitions on the disk. Select the white space (unallocated). Click on "disk options (advanced)". Click on "New" to create a new partition in the white space. Keep the default size, click "Apply". Click "Format". A popup window appears stating that the partition may hold OEM data. Continue. Click "Next". Installation starts.
Continued in the second post...Step 11) Win Vista/XP will reboot several times during installation. You will always see the Windows bootmanager with an entry for "Earlier Windows version" and "Windows Vista/7". DO NOT DARE to touch the blue Thinkvantage button on any reboot or press any function keys!
Step 12) When the installation is finished, check that you can successfully reboot Win Vista/7 by selecting it from the Windows bootmanager.
Step 13) Reboot XP by choosing "Earlier Windows version" from the Windows bootmanager. Open a command prompt. CD to the BMGR dir. Enter the following command:
bmgr32 /info /v
The output will now look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
Opened Master Boot Record to see whose MBR it is.
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
# active type start CHS end CHS startLBA size
0 0x80 0x07 1 1 0 254 255 255 63 109675692
1 0x00 0x07 239 255 255 239 255 255 109676544 191619072
2 0x00 0x12 239 255 255 239 255 255 301296240 11279520
3 0x00 0x00 0 0 0 0 0 0 0 0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
startLBA and size will of course differ, depending on the actual partition sizes you have set. Note that Windows setup moved the service partition to entry 2 of the partition table. If you do not see the 0x12 partition then stop here.
Otherwise the following step will likely screw up you harddisk.
Enter the following command (case sensitive?):
bmgr32 /Fbootmgr.bin /m0 /IBM /v
The output will look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /Fbootmgr.bin /m0 /IBM /v
installing MBR
finding free sectors
Sector 9 is free
Sector 10 is free
Sector 11 is free
Sector 12 is free
Sector 13 is free
Sector 14 is free
Sector 15 is free
Sector 16 is free
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
Setting Think bit
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
This command reinstalled the Lenovo bootmanager in the MBR that was erased by the Win Vista/7 setup program.
Enter the following command:
bmgr32 /info /v
The output will now look like this:
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>bmgr32 /info /v
It's a Lenovo MBR
Opened Master Boot Record to see whose MBR it is.
It's a Lenovo MBR
Opened drive for reading
Partition 0 the SP? no, type 0x07 is not correct
Partition 1 the SP? no, type 0x07 is not correct
Partition 2 the SP? (512) Label is SERVICEV
Using version 2.05 of Lenovo Boot Manager
Reading: \\.\PHYSICALDRIVE0
MBR Sector 1 Index: 1 Checksum: 00 Disabled
MBR Sector 2 Index: 11 Checksum: 03 Passed
MBR Sector 3 Index: 12 Checksum: FD Passed
MBR Sector 4 Index: 13 Checksum: 58 Passed
MBR Sector 5 Index: 14 Checksum: 96 Passed
MBR Sector 6 Index: 15 Checksum: 7F Passed
Data Sector Index: 10 Checksum: 01 Passed
Original MBR Index: 9 Checksum: 12 Passed
No Patch Sectors
Checksum Byte: 00
Think Flag: 1
WinPE Partition (0-3): 2 Alt Boot Partition (0-3): 2
Boot Config: 0 (Service Partition containing one Service OS)
Boot State: 0 Alt Boot Flag: 0
(Normal booting operation, will boot to Customer OS)
RRU: 00000000 00000000 Prev Active Part: 255
Previous Partition Type: FF Patch IN: 0 OUT: 0
CIRT Disabled
TOC: 0000000000000000 Lock: 0
Show Error: 0 Halt on Error: 0
CIRT Load Return: 0
CIRT Execute Return: 0
Pause Duration: 10 Scan Code: 0085
F11 Msg: To boot to the Rescue and Recovery Environment, Press F11
Check Msg: There has been a signature failure
# active type start CHS end CHS startLBA size
0 0x80 0x07 1 1 0 254 255 255 63 109675692
1 0x00 0x07 239 255 255 239 255 255 109676544 191619072
2 0x00 0x12 239 255 255 239 255 255 301296240 11279520
3 0x00 0x00 0 0 0 0 0 0 0 0
C:\Programme\Gemeinsame Dateien\Lenovo\BMGR>
So you have actually regained the Lenovo bootmanager. But you are not done yet.
Step 14) Shutdown. Restart the system. DO NOT PRESS THE BLUE THINKVANTAGE BUTTON AT THE SYSTEM STARTUP SCREEN!!! IT DOES NOT WORK YET! When the system startup screen DISAPPEARS, quickly press F11 (maybe several times). The system should now boot the predesktop environment from the service partition.
Step 15) When the predesktop is there, choose "warmstart". When the system startup screen appears, press the blue Thinkvantage button. The system should again boot into the predesktop. The blue Thinkvantage button now works permanently.
Step 16) Check that you can boot Win XP and Win Vista/7 from the Windows bootmanager. You're done! -
Re: How to install Windows Xp on pre-Vista laptop Satellite A300?
Hello
I'm now facing a problem when i try to install windows xp on my pre- Windows Vista laptop operating system ..
A300 when i input windows xp disc and boot from cd/dvd .... there is an error tell me that : you have viruses on your hard disc or scan it from viruses , or something like that but i test the same OS disc into other pc and its working also i have Gdata IS 2012, and i think its restriction from toshiba or i dont know , but its very important to install windows xp ...
i hope you help how to install windows xp on my laptop .
Regards
JohnHello John
It is not easy to understand the whole situation, especially this part with viruses.
In my opinion WXP installation should not be problematic.
What you need is WXP SP2 or SP3 disc and SATA driver. Without SATA driver HDD will not be visible for WXP.
More about that you can read on http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=38 -
How to install Windows 8.1 Pro on Macbook Pro
Hello everyone,
I'm new to these forums and new to bootcamping as well but have been reading all kinds of posts about how to install Windows 8.1 on their Macs using bootcamp. I am however having trouble with this situation as I have no clue what to do next. I have a Macbook Pro 2011, running on Maverics, and I recently downloaded a digital copy of Windows 8.1 Pro, 64-bit, for the Mac platform, along with its CD key through my University's hub website as can be seen here.
After finishing the downloading process, I received this file which is about 4GB large.
When i double click on the file this happens. It opens something on DEVICES which gives me what is on the 2nd image.
At this point, I'm at a loss on what to do next. Do i burn the file on a DVD hoping that Bootcamp will recognize it as a windows disc? Any help would be appreciated, thank you.You need a 'Full' Installer.
From Boot Camp 5.1: Frequently asked questions - Apple Support
Which versions of Windows work with Boot Camp 5.1?
Boot Camp 5.1 supports 64-bit, non-Enterprise versions of Windows 7, Windows 8.0, and Windows 8.1. This version of Boot Camp doesn't support Windows XP, Windows Vista, or any 32-bit version of Windows. Depending on your Mac, you may be able to use an earlier version of Boot Camp to work with other versions of Windows. For details, see the Boot Camp system requirements for Microsoft Windows.
Can I perform an upgrade install from a 32-bit version of Windows to a 64-bit version of Windows?
It's not possible to upgrade a 32-bit version of Windows to a 64-bit version of Windows. Back up your important files, then perform a new install of the 64-bit version of Windows. -
How to install windows 7 on Old Macbook Pro 15'inch 2.3 Core 2 Duo
How to install windows 7 on Old Macbook Pro 15'inch 2.3 Core 2 Duo:
I want to known how to install windows 7 on Old Macbook 15'inch 2.3 Core 2 Duo by using usb
I try many time, but after restart bootcamp partition, apple show blinking folder error
I think this firmware not support to install windows by usb
NOTE:
I Cannot install Apple New OSX Mountain Lion, Mavericks etc in this MAC
If I cannot install windows 7 on this MAC, so tell me what I will do with this MAC ?I agree with the optical drive, mine acted strange, and i thought people were crazy and my drive was shot, but a simple cleaning disc worked miracles.
But- are you trying to reboot with both the USB install and the DVD install both plugged in? that would definitely cause confusion.
Do this, reboot with NOTHING plugged in. Once you hear the Mac chime, immediately press and hold option.
You should only see the Mac HD, and Recovery Partition.
THEN plug in your external DVD, and wait a min or two, you should see a disc icon appear next to the recovery partition that says something like windows. If that doesnt appear after a min or two, unplug it and put the USB stick and do the same thing. I had to do it this way on my mid 09 MBP.
Let me know if this works to start the install. If not we may have to start over with Bootcamp Assistant -
How to install Windows on a SATA boot drive
Here is how to install Windows XP on a SATA boot drive. This procedure was first developed by syar2003 and has been used by many iusers ncluding myself. Although it was originally developed for Neo2 mb's and Windows XP Pro, it has general applicability to systems as well.
1. Have only the SATA drive you want to be the boot drive active in your system. Disconnect the power to all other HDD's if any.
2. Have only one optical drive active. Disconnect the power to the other opticals if any. (Best to have a burner optical as master on IDE1.)
3. Plug SATA drive into SATA 1 on the mb. (it may show us as an IDE drive somewhere down the list in BIOS. That's okl)
4. Enable appropriate SATA options in BIOS. Set boot order to floppy, cd, SATA drive. Set boot priority to SATA drive.
5. Partition and format the SATA HDD using the utilites CD that came with the SATA drive. (If you don't have an HDD utilities disk, download one from the website of your HDD manufacturer.)
6. Run Windows setup. No need to load drivers at the F6 promt unless you are planning to do a RAID configuration.
7. Windows XP should install without incident.
8. After you are up and running, plug the power back into your other HDD and optical drives if any.
If you have a board older than the K8 series, it may be necessary to load the SATA drivers at the F6 prompt. If the above procedure does not work, than try it again loading the SATA drivers.
If this procedure does not work for you, it is likely that your particular SATA HDD has some compatablity problem with Windows setup and/or your motherboard. The solution to this is to try another SATA drive. In general, most failures using this procedure have been traced to certain WD, Seagate and Hitachi SATA drivers of smaller capacities. Fewer problems seem to have occured with Maxtor HDD's.Kaplan, from an earlier post of mine regarding sata2 hdds - I have them plugged into the sata1&2 ports, installed the nvidia raid first and then installed winxp (in both raid 0 and raid 1). My bios is 3.1 and its a known problem that bios 3.3 & 3.4 have nvidia raid problems but seems to be fixed in the beta bios 3.53:
I just purchased 2 hitachi deskstar sata2 80gb hdds ($60 each at zzf) and the interesting thing about them is that you have to "enable" sata2. I have been testing the performance of sata1, sata2, raid1 and raid0 and the results are below.
The drives themselves are factory default set at sata1. Since I purchased OEM, no software or instructions were included. I had to go to the hitachi website download section to download a dos based program (the features program) to enable sata2. After enabling the hdds to sata2, they were recognized in winxp in the nforce ADMA controller device driver and the screen reads with the primary channel as Serial ATA Generation 2 - 3G...and all 4 boxes below it are checked (the boxes enable bios select xfer mode, enable read caching, enable write caching and enable command queuing are checked). An interesting thing about the sata2 spec is that all sata2 hdds must come standard with NCQ...its not advertised on these 80 gb hdds on the hitachi website (unlike the larger hitachi sata2 hdds) but its a standard sata2 spec and these 80gb hitachi hdds are recoginized in winxp as sata2.
The other interesting feature about the hitachi sata2 hdds is setting them up to operate in an adjustable "performance" to "silence" mode. The hdds are default set at high perfromance but you can manually lower the performance to increase the silence of the hdds which is fully adjustable to your liking. I tested the highest silence/lowest performance setting and you cannot hear the hard drive at all.
Testing - I tested the 2 hitachi sata2 deskstars with the first result in sata1 mode, the second in sata2 mode, the third in raid1 mode and the fourth in raid0 mode.
First, a significant increase in raid0 over sata1, sata2 and raid1 with sequential reads and writes (PC Wizard).
Write: 28mb/s vs 29mb/s vs 27mb/s vs 53mb/s
Read: 45mb/s vs 46mb/s vs 43mb/s vs 83mb/s
Second, significant increase in sata 2, raid 1 & raid 0 over sata1 with buffered reads and writes (PC Wizard).
Write: 104mb/s vs 176mb/s vs 165mb/s vs 266mb/s
Read: 123mb/s vs 200mb/s vs 200mb/s vs 293mb/s
Third, significant increase in sata 2, raid 1 & raid 0 over sata1 with burst reads (HD Tach).
Burst Read: 133mb/s vs 225mb/s vs 219mb/s vs 334 mb/s
It is interesting to note that raid1 is better than sata1 but marginally slower in all tests over sata2. Raid0 is significantly faster on all tests. -
How to install Windows 7 from a USB drive!
This is even easier than installing Windows XP from a USB drive, and will also reduce the time taken to install Windows 7, it took me about 15 minutes!
The advice in the guide is also applicable to installing Vista.
You need basically:
a USB flash drive at least 4GB in size
a Windows 7 DVD
To sum up:
Format your USB drive, with the NTFS filesystem
Open Command Prompt as an administrator, and run the Bootsect.exe program off the Windows 7 CD to make the USB drive bootable
Copy the contents of the Windows 7 DVD to the USB drive
Restart your PC, press F11 (or whichever key it is) to access the Boot menu, and select your USB drive to boot from
Full guide here:
http://www.intowindows.com/how-to-install-windows-7vista-from-usb-drive-detailed-100-working-guide/Quote from: bnborg on 16-February-11, 10:28:04
I have done this and it is simple.
I cleaned and (re)formated an 8GB flash drive under Windows7 using diskpart. I chose quick format and a fat filesystem. It doesn't need to be ntfs. I had diskpart mark the partition active. I copied the DVD contents to the flash drive. I also made a folder on it for motherboard drivers.
After that, I booted the drive on a new machine. Windows7 setup came up, and didn't find any hard drives, other than the USB flash drive. I clicked the button to load drivers, and pointed it to the folder I had copied them to on the flash. Windows installed without problems.
Hi bnborg..Do u mind sharing with me your motherboard driver folder? I have the MSI U135DX Netbook and each time I hit the button to install Windows 7 it asks me for some mobo driver...Think i might need it to get tru with a successful install.. -
How to Install Windows 7 Without the Disc
1a) Here is very useful article from PCWorld.com. The article is entitled "How to Install Windows 7 Without the Disc" and means just what it says. The article also has links to Magical Jelly Bean Keyfinder and legitimate Windows 7 ISOs from Digital River, a licensed distributor of Microsoft software. The article lists "Step 1" as;
"Find your Windows 7 product key: Typically this 25-character alphanumeric string is printed on a sticker affixed to your PC or on documentation included with your PC. Alternatively, you can use a keyfinder program such as Magical Jelly Bean Keyfinder to pull your product key from the Registry. You need your product key to reinstall Windows."
1b) Using a key finder, however, is only useful if the Windows 7 product key was printed on a sticker (Microsoft Certificate of Authenticity) affixed to your PC, on documentation included with your PC, or sent via email by Microsoft. Assuming your computer came from one of the big brand computer manufacturers... HP, Sony, Dell, Gateway, etc... as most do, it uses a generic "mass activation" OEM SLP key. Trying to use this key by itself isn't going to work. This OEM SLP key needs to be mated with an OEM SLP certificate and an appropriate OEM BIOS with a proper SLIC table.
1c) Here is where ABR Beta With Windows 7 Support comes to the rescue. Follow the "How to use it" section of ABR for Windows Vista for information and instructions on how to use ABR. The steps listed for Vista apply to Windows 7 as well. Perform the "activation backup" to "backup" and save the OEM SLP key and OEM SLP certificate. Save the entire ABR folder to an external location for later use. This will allow you to pre-activate your "clean" Windows 7 install on the computer you pulled the key and certificate from.
1d) Now install Windows 7 from your new "Windows 7" disc or USB stick, following all prompts as needed. Don't enter a Windows 7 product key if request. Also, don't allow Windows to try to auto-activate. Once Windows is fully installed, run ABR "activation restore" to "restore" the previously backed up product key and certificate to the new Windows 7 install. Verify that Windows is activated, repeat "activation restore" if needed.
2) Here is another useful article, this time from SevenForums.com. This arcticle is entitled "Clean Reinstall - Factory OEM Windows 7" and provides detailed steps required to backup your computer, audit current hardware and software, locate software and drivers, install and activate Windows 7, and create a Windows 7 Backup Image of your fresh install.
Good luck.
Links to additional Windows 7 SP1 "Editions" and "Languages" can be found HERE and HERE.
Link to "ei.cfg Removal Utility". The "ei.cfg Removal Utility" is a simple tool that will remove the ei.cfg from any Windows ISO disc image, thereby converting the image into a "universal disc" that will prompt the user to select an edition during setup instead of being forced to use different discs for different versions of Windows 7.
Direct link to Windows 7 USB/DVD Download tool.
<Cross posted to Notebook Operating Systems and Software for Notebook, Laptop, and Netbook users>
EDITED by Frank on 8/28/2013
Please click the white KUDOS star to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240ervis,
Before formatting the hard drive you should have been able to use the HP Recovery Manager to create your recovery discs or perform a system recovery. This is provided the recovery partition wasn't already corrupt or damaged. If the "D:" HP Recovery partition is missing or damaged and you don't have a set of HP Recovery Discs, you will need to use the information in my previous post to get your computer up and running again.
The information in the document referred you to applies to several different "types" of installations;
Using ABRbeta is only needed if you have an active OEM factory SLP (system locked preactivated) installation of Windows. You use ABR to pull the factory key and certificate off the computer, to reuse it on the same computer with a clean Windows install.
If you are just installing Windows and are going to use the Windows 7 product key on the COA on the side of your computer, all you need to do is download the same version of Windows that your key is for and burn the ISO. Now install Windows answering or following all prompts as needed (except do not enter the Windows product at this time... it will be entered later). Once Windows has completely installed, enter the key and activate it. Your Windows 7 OA key should work on a SP1 install without issue.
The only thing I see that could mess things up, is the language of the install. If you are still having trouble activating Windows, please reference the ISO you download and a post a photo of your Windows COA
with the key erased or Xed out.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240 -
Satellite A210-15Y - How to install Windows XP?
I had Windows Vista and I upgrade it with Windows 7. Now I really want to install Windows XP.
When I put Windows XP CD in after a while I get an blue screen whit an error .
pls tell how to install Windows XP on my notebook and if I need some drivers to do it pls put links from whereIi can get them.
P.S. sorry for bad englishHi
I think the problem is that you tried to install the Win XP without installation of SATA driver.
The A210 needs SATA driver in order to recognize the HDD.
You could also check the BIOS settings. There should be a option called SATA mode.
This can be set from AHCI to compatible and this will allows you to install the Win XP without the first installation of SATA drivers.
Please also check other threads here in the forum about the same theme!!!
PS: It's advisable to use Win XP including SP3!!! You can include the SP3 using the nLite software!!! -
How to install window xp in compaq presario cq60 not book
how i install window xp in compaq presario cq60 in my not book! please help me, i have trouble with vista so please sir help me. i can't find cam driver, not work properly with .net. there ar so many problame so please help me please please..........
There is a Guide for that here.
http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and/General-XP-Downgrade-Guide-for-HP-Laptop...
Yours is one of the moderate models and you will find links to all the drivers you need. My own take on this is you are going in the wrong direction. Instead of back to XP you should go forward to Windows 7, but XP can be made to work on that machine. Good luck and feel free to post back with any more questions. -
How to install windows on the SSD (Y580)
I have bought an Y580 recently wIth a 64GB SSD and 1TB HDD. I asked the salesperson upfront if the OS would be on the SSD. He said yes. Turns out that it is not. When i returned to them they told me it's a hybrid drive solution. And they have no idea how to install Windows on the SSD.
I did some research and found out that Lenovo uses *Rapiddrive* to speed up programs. Hence why i can't see the SSD in WIndows as it is merged with the 1TB HDD. In Disk management 2 disks show , 0 and 1 , but Windows asks to give disk 1 a MBR or GPT (this is apparantly due to the rapiddrive methode).
My questions:
* Is it possible to install Windows on the SSD and if so how can that be done without loosing the backup on the hidden partition of the 1TB disk? (so that OKR still works)
* What are the benefits of Rapiddrive over using the SSD as bootdisk?Since it is a hybrid drive, it works a little bit differently; Lenovo's "Rapiddrive" is also different from other hybrids, and in the sake of making it "user friendly" and seen as a single disc they have probably nerfed some configurability for the intermediate/advanced users. However, Windows should already be installed on the SSD portion of the drive, this should be done automatically according to this press release:
http://shop.lenovo.com/us/sitelets/ee/consumer-news
"In the factory we will preload not just Windows 7 on the SSD, but also our Lenovo applications like OneKey™ Theater or OneKey™ Rescue System. The applications, operating system, drivers and other files are all fully-optimized for Enhanced Experience to make them load much faster. This, combined with their installation on the SSD will make the boot time to Windows desktop even faster. Some portion of the SSD will also be reserved as the Windows Paging File — this is used by Windows as 'virtual memory' additional to the normal RAM installed inside the computer. With the SSD acting as the Paging File, general Windows 7 performance will also benefit, especially when multitasking several applications.
The remaining space, which will typically be around 15GB on a 32GB SSD, will be empty, ready for the user to install their favorite applications and files."
I have some of the fastest SSD's around installed on my desktops (SATA III), and while they are blazing fast, keep in mind the whole boot sequence still isn't going to be instantaneous even with an SSD (the biggest differennce you will notice is by the time Windows is loaded, it's fully loaded to the RAM, whereas a normal HDD you may see the desktop but your PC will still be cranking away with startup processes). If your startup is taking 30 seconds or less, maybe even a little longer, it's probably accessing the SSD just fine; if it's taking closer to 60 seconds, then yeah it may need to be reinstalled/reconfigured.
As for reinstalling, sorry I won't really be able to help, hopefully someone else can come along; I personally have never used OKR anyways, and aside from doing a ghost backup I wouldn't say for sure that OKR would be salvageable with a fresh install. And because the Rapiddrive is its own technology, half SATA half PCI-E, I also couldn't tell you if it's even possible to fully seperate the two and keep them as distinct drives. -
Somebody can help me how to install windows in my imac
Somebody can help me how to install windows in my imac
Windows on Intel Macs
There are presently several alternatives for running Windows on Intel Macs.
1. Install the Apple Boot Camp software. Purchase Windows
XP w/Service Pak2, Vista, or Windows 7. For Boot Camp
4.0 and above you can only use Windows 7 or later. Follow
instructions in the Boot Camp documentation on
installation of Boot Camp, creating Driver CD, and
installing Windows. Boot Camp enables you to boot the
computer into OS X or Windows.
2. Parallels Desktop for Mac and Windows XP, Vista Business,
Vista Ultimate, or Windows 7. Parallels is software
virtualization that enables running Windows concurrently
with OS X.
3. VM Fusion and Windows XP, Vista Business, Vista Ultimate,
or Windows 7. VM Fusion is software virtualization that
enables running Windows concurrently with OS X.
4. CrossOver which enables running many Windows
applications without having to install Windows. The
Windows applications can run concurrently with OS X.
5. VirtualBox is an Open Source freeware virtual machine such
as VM Fusion and Parallels that was developed by Solaris.
It is not as fully developed for the Mac as Parallels and VM
Fusion.
Note that VirtualBox, Parallels, and VM Fusion can also run other operating systems such as Linux, Unix, OS/2, Solaris, etc. There are performance differences between dual-boot systems and virtualization. The latter tend to be a little slower (not much) and do not provide the video performance of the dual-boot system. See MacTech Labs- Virtualization Benchmarks, January 2013 | MacTech for comparisons of Boot Camp, Parallels, and VM Fusion. Boot Camp is only available with Leopard or Snow Leopard. Except for Crossover and a couple of similar alternatives like DarWine you must have a valid installer disc for Windows.
You must also have an internal optical drive for installing Windows. Windows cannot be installed from an external optical drive. -
How to install window 7 on mac mini ?
how to install window 7 on my mac mini?
Windows on Intel Macs
There are presently several alternatives for running Windows on Intel Macs.
1. Install the Apple Boot Camp software. Purchase Windows
XP w/Service Pak2, Vista, or Windows 7. For Boot Camp
4.0 and above you can only use Windows 7 or later. Follow
instructions in the Boot Camp documentation on
installation of Boot Camp, creating Driver CD, and
installing Windows. Boot Camp enables you to boot the
computer into OS X or Windows.
2. Parallels Desktop for Mac and Windows XP, Vista Business,
Vista Ultimate, or Windows 7. Parallels is software
virtualization that enables running Windows concurrently
with OS X.
3. VM Fusion and Windows XP, Vista Business, Vista Ultimate,
or Windows 7. VM Fusion is software virtualization that
enables running Windows concurrently with OS X.
4. CrossOver which enables running many Windows
applications without having to install Windows. The
Windows applications can run concurrently with OS X.
5. VirtualBox is an Open Source freeware virtual machine such
as VM Fusion and Parallels that was developed by Solaris.
It is not as fully developed for the Mac as Parallels and VM
Fusion.
Note that VirtualBox, Parallels, and VM Fusion can also run other operating systems such as Linux, Unix, OS/2, Solaris, etc. There are performance differences between dual-boot systems and virtualization. The latter tend to be a little slower (not much) and do not provide the video performance of the dual-boot system. See MacTech Labs- Virtualization Benchmarks, January 2013 | MacTech for comparisons of Boot Camp, Parallels, and VM Fusion. Benchmarks of all of the above except Crossover can be found in Benchmarking Parallels, Fusion, and VirtualBox Against Boot Camp - The Mac Observer. Boot Camp is only available with Leopard or later. Except for Crossover and a couple of similar alternatives like DarWine you must have a valid installer disc for Windows.
You must also have an internal optical drive for installing Windows. Windows cannot be installed from an external optical drive.
Maybe you are looking for
-
I am getting this error in my apache error logs when a try to run a report from the browser: [Wed May 08 10:08:35 2002] [error] Unrecognized character \220 at d:/oracle/isuites/apache/apache/cgi-bin/rwcgi60.exe line 1. I am using 9iAS.
-
3G iPhone saying I need a restore
I have had my phone for a couple of months now. This morning I woke up and the display showed I needed to connect to iTunes. I did so. When I plug my phone in it said my phone needed to be restored before I could use iTunes...... Okay, I dont have mu
-
How to get status of target system battery level
Hi, I want to get the current battery percentage on the target system with labview. Does anyone have DLL that I can use, or can someone please help me. The target system connected to the Host system running labVIEW via TCP/IP. thanks, John
-
Where can I find a full list of FRM Errors for forms 9i?
Where can I find a full list of FRM Errors for Forms 9i? I have installed Forms 9i + the documentation CD but it has very little documentation on forms, just lots of J2EE stuff.
-
I'm using firefox 3.6.4 dutch. On some sites telephone numbers are just visible during 1 second, then they disappear. When refresing they are again visible during 1 second. == This happened == Every time Firefox opened