How to maintain time spec.of operations in routing and work centers

Dear consultants,
We dont have any time specifications in routing or work center ..
we just create an order and the execution of the production involves many operations....
now we want to be specific about the time of operations as the need is to track the operations.( In the sense which of the operations are delayed).....
How and where should i do these in the routing and workcenters..
Please explain in detail....
Karthick

Hi Karthick,
In your work center in basic data page you maintain std. value key eg: SAP1, this has Setup Machine & Labor fields. In the default values page you specify the unit of measure Eg: HR
Now when you add this work center in your routing operation page, you will find Setup Machine & labor, here you maintain the time required for each of the process.
Now while doing confirmation via co11n, you inform the user to specify the time actually spent on each of the activity. In OPK4 for order type - plant combination you can specify a few defaults such as propose the value etc.
Hope the above is clear.
Regards,
Vivek

Similar Messages

How come every time i'm on the phone and another call enters I answer it but it doesnt tell me anywhere who is who on each line so i can go back and forth?? it only says multiple calls and i cant hang up the other line

how come every time i'm on the phone and another call enters I answer it but it doesnt tell me anywhere who is who on each line so i can go back and forth?? it only says multiple calls and i cant hang up the other line.

My carrier is Sprint. But I actually have checked with others and theirs work fine.

How to use time capsule as main wifi router?

it is connected in bridge mode to an ethernet port, connected by a wifi modem. how to i set it as the main router and get rid of the other wifi. the phone plug wont connect because there isnt one, what do i need to get so i can plug directly to the time capsule. im not tech savy so im not quite sure what im doing.
regards, Chris

Chris,
Here are the basics:
Rule 1: If your modem/router is acting as the main router (it is), then the Time Capsule must be configured in Bridge Mode.
Rule 2: If you want the Time Capsule to be the main router, then your modem/router must be configured in Bridge Mode.
Check with the support folks of your modem/router to find out whether this is even possible, and if so, how to do it....and more importantly make sure that your Internet service provider will support this type of setup.
Another option would be to simply replace your existing modem/router with a simple bridge mode modem. Ask your ISP about this.
Until you have a clear handle on this.....we cannot help you with support on your modem/router......it would be best to leave well enough alone and stay with your current setup with the Time Capsule in Bridge Mode.

Lead Time - Customizatiou0131n steps: Shipping point, route, and loading group

It says about delivery scheduling that "The lead time considers the shipping point, route, and loading group". Can anybody explain me briefly the customization menu steps about this sentence?
Thanks in advance.

Please go through this document it will help you
1) Maintain transportation planning point through Menu as follows:
IMG Maintain Logistic Execution  Definition Enterprise Structure  transportation planning point.
Create your own like BP01 enter the general data¡¯s required
2) Defining modes of transport:
IMG RoutesBasic Transportation Functions  Transportation Logistic Execution Define modes of transportDefine routes
Use the standard like:
Shipping type: 01
Description: Road
3) Define shipping types :
Basic Transportation Transportation Logistic ExecutionIMG Define shipping types Route Functions
Or through T-code: SM30
PT: 01
Description: Truck
Mdtr: 01
STPG: 0001
4) Define transportation connecting point :
LogisticIMG DefineRoutes  Basic Transportation Functions  Transportation Execution Define transportation connection pointsroutes
Copy the std point and make it FB01 as departure zone and FB02 as destination zone
5) Define routes and stages.
 Logistic Execution IMG Define Define routes Routes  Basic Transportation Functions Transportation routes and stages
Use the standard route and copy it as FB0001 and enter the departure zone and destination as what we created.
6) Defining Transportation Zone:
Basic Transportation Logistic Execution IMG Define transportation Router determination  Route Transportation Functions zones
Use the standard transportation zone depending on the route so as for the example use 0000000003 - Southern Region
7) Maintain country or transportation zone for shipping points
 Logistic Execution IMG  Route determination  Route  Basic Transportation Functions Transportation Maintain country and transportation zone for shipping point
Shipping point be ASH1 and route as 0000000003 which is assigned to country India
8) Maintain route determination:
Logistic ExecutionIMG Route determination Route  Basic Transportation Functions  Transportation  Maintain route determination
Country of departure: India
Departure Zone: 0000000003
Country of destination: India
Destination Zone: 0000000003
And enter the datas needed like shipping condition 01, etc.
Maintain Transportation relevance for shipping point, sales document type and delivery types.
9) Now create shipping types
IMG Define shipment Shipments  Transportation Logistic Execution types
Copy the standard 0001 and make it to AFIL
10) Define and assign traffic zones through T-Code: T_76 (or) thru menu as follows
IMG Define Basic functions  Shipments cost  Transportation Logistic Execution and assign tariff zones
Copy the standard and make it to FABTARIFF and assign our transportation planning point as ATP1, ATP2 assign tariff zone to every particular transportation planning point
11) Define and assign pricing procedures
Shipments Transportation  Logistic Execution IMG define and assign pricing Price control  Pricing cost procedures
Copy the standard shipping cost pricing procedure SDFC00 to FBSC01
12) Assign purchasing data:
 Logistic Execution IMG Assign purchasing data Settlement  Shipments cost Transportation
13) Assign transportation planning point to shipping condition, purchase organization, purchasing group and to plants.
14) Define Automatic G/L account determination:
 Transportation  Logistics Execution IMG Automatic G/L Account Determination Settlement Shipment Costs
Or through T-code: OMWB
Use G/L account 614000 as used in standard
15) Automatic determination of CO assignments:
IMG Automatic Settlement  Shipment Costs  Transportation Logistics Execution Determination of CO Assignments
Or T-code: OKB9
16) Maintain shipping point address.
 Logistics Execution  Definition Enterprise Structure Define, copy, delete, check shipping point
17) Creating G/L account centrally.
Financial AccountingAccounting  Master Records  General Ledger 
Individual Processing Centrally
Or through T-Code: FS00
18) Enter the G/L account 614000 to the company code AFIL
19) Create transportation condition records:
 Shipment cost  Transportation  Master data Logistic Execution createPrices
Or thru T-code: TK11
Enter condition type FB00 that is freight condition type, which is used as standard in the shipping cost pricing procedure.
Enter the price and save it
Process:
1. The system determines the pricing procedure for the shipment cost item-using transportation planning point, service agent and shipment cost item category
2. Calculation Basis
3. Condition Record
4. Access sequence.
For the sales order, create a delivery using VL01N and pick the goods. Now create a shipment using VT01N and assign the delivery to the shipment document. Make sure to enter the carrier and other details before performing the transportation planning and execution. Save the shipment document and PGI for the delivery would be done automatically.
A shipment represents a physical goods movement between two or more locations.
For the system to create a shipment, shipping-relevant deliveries must exist.
You use Transportation Planning to group pending deliveries into shipments and then to perform the shipments.
The outbound delivery documents contain routes that the system calculates in route determination, and a transportation planning date for the delivery.
Dynamic transportation planning is responsible for grouping together outbound deliveries into shipments that have at least the same route, visit plan type and the same transportation planning date.
The following restrictions can be taken into account for a shipment in Dynamic Transportation Planning:
Weight
Volume
Variable capacity
Number of stops
Maximum duration
Loading units
Create Shipment Document
Use
After the status of the delivery is open for transportation planning, it is possible to create a shipment document to schedule the transportation.
Transportation Create Single document Logistics Logistic Execution  TransportationPlanning
T.code: VT01n
Enter your transportation planning point and shipment type. Press enter.
Creating the shipment cost document
Use
After the deliveries are scheduled by shipment and the shipment is executed, now it is time to maintain and close the shipment document in order to record all relative information and ready for the shipment cost settlement.
Single document Logistics Logistic Execution  Transportation Shipment cost Create
T.code: VI01.
After creation of shipment cost doc. You settle the Shipment cost.
Go to VI02, enter shipment cost no.and press enter.
Then go to Overview -- Fright cost items, Select the line item and double click it.
Go as main menu: Item --> Acc. assignment, you enter G/L acc. and cost center to which the transportation cost will be posted.
On the Standard change, details Freight cost items screen, then check the check box Transfer, which means you will transfer the relative transportation cost to FI/CO, in this case, the system should determined which Purchase Order will used to settle the cost, so after you check the Transfer check box.
Press save button on the current screen.
Shipment cost settlement and documents:
Use
After the shipment cost settled in shipment cost document, it has the following affects:
It creates a service entry sheet that refers to the purchase order determined.
It posts acceptance of services performed.
It creates an accounting document for the accruals.
Further subsequent documents are created in FI.
Create Delivery:
T.code: Vl01n
Create TO:
T.code: LT03
Create Shipment Document
Use
After the status of the delivery is open for transportation planning, it is possible to create a shipment document to schedule the transportation.
 Transportation Planning  Create Single document Logistics Logistic Execution Transportation
T.code: VT01n
Enter your transportation planning point and shipment type. Press enter.
Creating the shipment cost document
Use
After the deliveries are scheduled by shipment and the shipment is executed, now it is time to maintain and close the shipment document in order to record all relative information and ready for the shipment cost settlement.
Single document Logistics Logistic Execution  Transportation Shipment cost Create
T.code: VI01.
After creation of shipment cost doc. You settle the Shipment cost.
Go to VI02, enter shipment cost no.and press enter.
Then go to Overview -- Fright cost items, Select the line item and double click it.
Go as main menu: Item --> Acc. assignment, you enter G/L acc. and cost center to which the transportation cost will be posted.
On the Standard change, details Freight cost items screen, then check the check box Transfer, which means you will transfer the relative transportation cost to FI/CO, in this case, the system should determined which Purchase Order will used to settle the cost, so after you check the Transfer check box.
Press save button on the current screen.
Shipment cost settlement and documents:
Use
After the shipment cost settled in shipment cost document, it has the following affects:
It creates a service entry sheet that refers to the purchase order determined.
It posts acceptance of services performed.
It creates an accounting document for the accruals.
Further subsequent documents are created in FI.
Generally process is-
1) VL01N
2) VT01
3) VL02N - PGI
4) VI01
5) ML81N Service Entry Sheet
6) MIRO Invoice Verification
Shipping docs (VT01) are created before PGI...
You cannot carry out transportation planning or creation of shipment after the goods issue has been executed. Once goods issue is done it means that the material has left your premises so there is no need for a transportation planning after it.
In case you need carry out the shipment documents at the end of the day you could just create the delivery documents during the day and at end of the day create the shipment documents and the goods issue
This link is also usseful:
http://help.sap.com/printdocu/core/Print46c/en/data/pdf/LETRA/SDTRA.pdf
Hope this helps you.
Regards
nitin

How do I use Time Capsule as a wireless router and turn my current one into modem only

I have a crappy modem/ router and before I purchase a new modem I want to use the modem (no wireless) feature of my router.
Question #1
How do I use my Time Capsule as a router?
Question #2
If I do this will I still be able to wirelessly back up to my Time Capsule?
Question #3
How do I turn off (wireless) or the router function of my modem/ router?
Question #4
I then want to connect all my wireless devices to my Time Capsule making that
the main WIFi in my house. I am assuming this is possible it is I just dont know how to go about doing this myslef without guidance, and the Airport Installer is confusing to me.
Thanks!

Question #1
How do I use my Time Capsule as a router?
Connect an Ethernet cable from one of the LAN <-> ports on your modem/router to the WAN port (circle of dots icon) on the Time Capsule.
Open AirPort Utility and click Continue to follow the guided setup to configure the Time Capsule to "create a wireless network". Select the "Bridge Mode" option when it appears during the setup. (AirPort Utility will normally do this for you)
Question #2
If I do this will I still be able to wirelessly back up to my Time Capsule?
Yes
Question #3
How do I turn off (wireless) or the router function of my modem/ router?
We prefer not to guess at things, but since we do not know the make and model number of your modem/router, and this is an Apple support area, we have little choice.
In general, you would enter the default IP address of the device into your browser to bring up the configuration pages (check your documentatio on the modem/router for this information, or it may be on the back or bottom of the device. An example of a default IP address is something like 192.168.1.254
There will be a wireless settings page that will allow you turn off the wireless function of the device.
If you acquired the modem/router from your service provider, they should be able to tell you how to do this as well, or if you check the manufacturer's website, they will likely have a support area for questions like this.
Question #4
I then want to connect all my wireless devices to my Time Capsule making that
the main WIFi in my house.
You will need to log on to the Time Capsule wireless network from each device and enter the password to connect. Most computers will "remember" the setting so that you do not have to enter the password each time that you connect.

How do I daisy chain two time capsules as a wired router and use the hard of both as back-up?

I have a newer time capsule tower and an older time capsule that I wasn't using. The older TC works fine I just decided to upgrade about 6 months ago. I decided to run an Ethernet cable from the room where the TC tower is to the room where the TV in order to create a wired connection to the TC tower. I wanted to use my Apple TV with a wired. In addition, I am in the process of buying a Channel Master DVR plus and besides wanting to use it with older TC wired also wanted to use the older TC’s hard drive to extend the recording time of the DVR. Will this work? If so, my questions are related to setup of all. I assuming I plug the Ethernet cable into the LAN port of the TC tower and the other end into the WAN port of the older TC. Is this correct? What settings do I need on the TC tower and the older TC to make this work as a wired connection? Do I need to turn off the wireless connection on the older TC? Will I just need to plug in the DVR into the older TC’s USB port to use its hard drive? Thanks for your assistance.

I assuming I plug the Ethernet cable into the LAN port of the TC tower and the other end into the WAN port of the older TC. Is this correct?
Yes
What settings do I need on the TC tower and the older TC to make this work as a wired connection?
The setup "wizard" will automatically provide the correct settings to the older TC to "extend a network using Ethernet" when you start from a factory default reset condition on the old TC.
Do I need to turn off the wireless connection on the older TC?
You can, but if the older TC is located some distance from the new TC, you might want to leave the wireless on to allow an "extended" network with more wireless coverage in the area near the old TC.
Will I just need to plug in the DVR into the older TC’s USB port to use its hard drive?
The USB port on the old TC (and new TC) will only support a normal computer hard drive.....not a DVR. If you want to connect a hard drive for more recording capacity, you will likely need to use a separate USB or SATA hard drive that is connected directly to the DVR, not to the old TC.
Check the documentation on the DVR to confirm how that device should be set up.

Has anyone enabled time machine using a linksys router and external hard drive? And if so how?

Has anyone enabled time machine using a link sys router and external hard drive? And if so how? I have a Linksys E4200 wireless router with a usb port on it. I also have a Western Digital Elements 1TB external hard drive. I would like to be able to use this hard drive with time machine. Has anyone done so and if so how can I do so?

You might get some responses, but we don't see many Linksys users on an Apple forum so it may be awhile before you see an answer.
It might be useful to point out that Apple does not even support Time Machine backups to the USB port on their own AirPort Extreme wireless router, so we may be heading down a very slippery slope here.
I've tried Time Machine backups on an AirPort Extreme router a number of times in the past. It's just not reliable. Works for awhile, then has corruption problems. Or has corruption issues immediately. I once went a month or so and thought I had it nailed, then got smacked with a corrupted set of backups again.
But, I guess you never know. It might work on the Linksys. If you decide to try this, I would suggest that you have another backup plan in place for your important data.
Hope that some Linksys users will respond so we can all learn.

How to setup TIme capsule with a DSL router step by step?

Hi All,
Does anyone know how to conncet Time Capsule set by step through a DSL router?
I already have a DSL router, but want to connect my time capsule to that router.
Do i connect it through ethernet?, and is it possible to have my time capsule as a different router at home with a different password than the DSL router?, if so how is that possible?, is going to have the same download/upload speed as the DSL router?
Please help, thanks

You simply bridge the TC.
Plug it by ethernet into the adsl modem router and it will work fine.
nd is it possible to have my time capsule as a different router at home with a different password than the DSL router?,
No, the TC will cause trouble if you set it up as a router.. it has to be bridged. You only have a single adsl connection but there are some ISP that allow a secondary pppoe login and some modems that allow it. It is pretty difficult setup. Ask your ISP as there is often a charge that is very high for the second connection. It will still share the same link so there is no improvement in speed, merely two different authentications sharing the same line. The TC can do pppoe client but has nothing very fancy about it.

How do I know if my password is set and working?

I know this seems like a stupid question but I just had a very hard time getting my new Airport Xtreme to work. After being on the phone with my cable internet provider and Apple for almost two hours it works now, but I'm not sure if my password that I set to join the network is still working. When I turn on my Macbook Pro the airport signal automatically is full and doesn't ask me for password, does that mean my neighbors can get on too or is that normal?
If that means the password is not set, how do I set it, and will it reset the Xtreme base (hopefully not because I don't want be on the phone for two hours again)
thanks

Start your Airport Admin Utility and connect with
your AEBS, then select "Change Wireless Security"
Does it say something other than "Not Enabled" under
wireless security? If so, you are running encrypted,
if not, post back and let us know.
This may also help:
ttp://docs.info.apple.com/article.html?artnum=106424
or this
http://docs.info.apple.com/article.html?artnum=107921
When I open the Airport Admin Utility and click Change Wireless Security, it says WEP in Wireless Security option, does that mean the password and name I chose in the setup process is working then? I didn't see "Not Enabled".
I was just curious if it was working because when I turn on my computer, the internet is on, I don't have to choose to join my network or type in my password. When it said "remember password in Keychain" does that mean only my computer doesn't need to type in my password every time I turn on my computer to connect to the internet?
Thank you for your help!
MacBook Pro 15' Mac OS X (10.4.6)

Set up Time Capsule w/ belkin modem/router AND DSL splitter

G'day,
I've got an existing network set up and would like to add the Time Capsule into the network. I'd like to use my current hardware if possible but am willing to purchase stuff if I need to.
There are some posts on my model of Belkin modem/router, but it didn't really help me.
Here are my machines:
1) PC - desktop (ethernet networking card, Windows 7,
2) Laptop (wireless networking, Windows 7)
3) Macbook Air (wireless networking)
4) iPhone (wireless networking)
Here are my hardware:
A) Wall socket
B) DSL splitter (3 x ports - port for line, port for phone, port for modem)
C) Cordless phone
D) Belkin modem/router (model number F5D7633-4A - 1 x ADSL port, 4 x Ethernet cable ports)
E) Time Capsule
Here is my current set up:
Wall socket > phone cable > Splitter > phone cable to phone, phone cable to modem/router > ethernet cable from modem/router to PC
This solution gives me internet access via the ethernet cable to the PC and via the Belkin modem/router wirelessly to the Laptop. However, I haven't been able to connect my Macbook Air to this network yet - it doesn't seem to work.
So my question is, how can I include my Time Capsule into the network. Will I need another modem? I read about a bridge but I have no idea what that is or where to find that setting.
Also, can someone explain how to get my Macbook Air to connect to the network?
Can someone talk me through exactly what extra hardware I need and what I need to do to set it all up?
Cheers,
Chris

Hi Bob,
Thanks for chiming in. Could you talk me through how to do that? I'm a numpty and just haven't figured out which ports to plug which cords into, etc. If you or someone else could dumb it really right down that would be sweet.
Also, the Belkin is a modem/router, not a router. I am under the assumption that I need a modem to access the internet and that the Time Capsule is just a router.
Is that right?
Chris

Setting up Time Capsule as primary wireless router and enabling port forwarding

I am attempting to setup my Time Capsule as the primary router on my wireless network. I have an Actiontec Verizon FIOS router that I am connecting the TC to using ethernet, and I was then going to turn off the wireless function on the Verizon router so that the TC will be the only wireless router. I am not exactly sure how to go about this, and I also have to connect a wireless device to the TC that requires a static IP address and port forwarding enabled so that I can access from my iPhone. I am completely lost on how to do this, any help will be greatly appreciated.

Unless Verizon has made a major change in the last few days, you will not be able to use the TC as the primary router......simply because it is not possible to configure the Verizon router to act as a simple modem......which is what it must do if you want to have the TC act as the primary router on your network.
As LaPastenague has explained. turning off the wireless on the Verizon modem/router will not make it a modem. It will still be a wired modem/router in charge of the network, not allowing the Time Capsule to take over the role of main router for the network.
But, let's assume that I am wrong. Please check with Verizon support and ask them........
1) If it is somehow now possible to configure their modem/router to act as a simple bridge mode modem. If they say that this is not possible (or they will not support this).....
2) Ask them if they can provide you with a simple, bridge mode modem......instead of the modem/router that you have now. A simple modem will have only one Ethernet port, and it will not offer any type of routing or wireless service at all.)

How can I access iCloud documents from my iPad and work on them on my iPad

How can I access and work on documents in the cloud on my iPad, not a computer

Thank you, I really appreciate your time, but I think I am after something the iPad won't do. I don't want to use a computer at all. I would like to open an iCloud doc using my iPad, work on it (on the iPad), then print or save it back into pages or the iCloud.
From your responses, it sounds like you have to use an iPad in conjunction with a computer, of some description, to work on documents in the cloud, the iPad alone will not let you do this.
So I guess the short answer is, I can't.
Thanks for your time and input.

Back To My Mac to a Time Capsule through a 3Com Router not working

I have a Mac Book Pro (10.5.7), Time Capsule (7.4.1), 3Com Office Connect Wireless Router (3CRWDR101A-75), a trial subscription to Mobile Me and a 2.5G iPhone (2.2.1).
I have been unable to get BTTM from my Mac on a remote wireless connection to my Time Capsule working - hence this post.
The set up of the Time Capsule was quite straightforward (as I would have expected from Apple) and I quickly established local and remote iCal / Address Book sync between my Mac, www.me.com and my iPhone. I have enabled and am the 2.4 and 5GHz bands on the Time Capsule and the wireless air interface on the 3Com router has been turned off. All of internet and email services on my Mac work well locally and Time Machine work. So far so good.
However, I am unable to 'see' my Time Capsule in Finder from any WiFi network that is not my home network. When at home I have full access to Time Capsule's disk.
My 3Com Office Router 3CRWDR101A-75 is not on the list of supported routers (nor is any other 3Com Router) but it does provide UPnP and NAT as required according to Mobile Sync notes including http://support.apple.com/kb/HT1552 and http://support.apple.com/kb/HT1552. Despite my best efforts, I have been unable to find out from Apple's MobileMe support if there are any minimum requirements for any router to work with Back To My Mac so can't check to see if my 3Com router will ever work with BTTM or not.
Does anyone have any similar experience with setting up a 3Com Office Connect router to work with Back to My Mac?
Do I need to check / Can I check if my Time Capsule has been registered with the Mobile Me servers?
Do I need to enable any specific ports on my 3Com Office Connect router?
Basic settings:
Time Capsule: green light - all OK
AirPort Utility>Internet: Connection Sharing: Off (Bridge Mode)
AirPort Utility>Advanced>Mobile me: account set up
AirPort Utility>Advanced>IPv6: IPv6 mode = Node, at the request of Apple Mobile Me support
System Preferences>Mobile Me>BackToMy Mac: On (green light).
3Com Office Connect Router: DCHP server: On
3Com Office Connect Router: Firewall level: High (default)
3Com Office Connect Router: Disable NAT: Off (default)
3Com Office Connect Router: Enable Universal Plug & Play: On
3Com Office Connect Router: Enable IPSEC-NAT pass through: ON, at the request of Apple Mobile me support
Com Office Connect Router: DMZ: enable 1-to-1 NAT: Off (default)
Any ideas?
Thanks.

Quick update on troubleshooting BTTM (or rather Back To My Time Capsule)...
Surprising;y, no 3Com products listed in http://support.apple.com/kb/TS1304. 3Com tech support stated that no OfficeConnect products have been qualified against BTTM and my specific router does not support IPv6 over IPv4 encapsulation.
MobileMe support were not able to help, citing the fact that I had an unsupported router.
I have made no change to my modem/router config since first posted but since an upgrade of my TC to 7.4.2 I have been able to use BTTM with my TC (bridge mode) and my OfficeConnect modem/router (802.11b WiFi disabled).
I have made limited testing from other remote locations from my MBP and also proved that it worked over a 3G/UMTS connection on the UK's 02 network also
MobileMe still reporting uPnP / NAT problem on my MBP when working remotely though.
http://discussions.apple.com/message.jspa?messageID=9733258 confirms that this has been solved and, apart from the anomalous Mobileme status message, I can agree.
Good news so now do not need to swap out my 3Com router. Also shows that this 3Com product does meet BTTM connectivity requirements.
Message was edited by: Elise49
Message was edited by: Elise49

Spot remover tool / healing brush. How do I get the brush to show up and work??

It seems I can only get the spot remover tool to work on certain photos and in certain areas of said photos . On the one picture I really need this for--where the problem started--I had used it once without much success (it was working then, but I didn't do it right). So I left the picture and worked on another. When I came back to the first picture, I brought up an earlier version of it, before the initial spot removal, to work on. Now I can't get the brush to even show up on the frame, although other tools are working fine. I've checked on other pictures and it seems that many times the spot remover brush won't show up. WhY???

Great. There are other keyboard shortcuts when using this tool like the forward slash key and holding down shift if cloning an area that is a straight line. And don’t forget you can click on the word reset. Take a look at this short video tutorial from Adobe TV.
http://tv.adobe.com/watch/adobe-evangelists-julieanne-kost/lightroom-5-advanced-healing-br ush-and-visualization-tool/

Using Time Capsule as a 'wireless' router and backup using Time Machine

I have a question about backup speed on my 1 TB Time Capsule. I purchased a Time Capsule about a year ago and have an imacg5 and two Mac laptops that I setup to use the wireless router capability and as the backup drive for all three computers.
I was experiencing a problem in that the backups from the imacg5 were never completing even though the Time Machine window said it was only backing up several MBs. In order to 'fix' the problem I finally 'erased' all of the backup files on the Time Capsule using Airport Utility. I had also run Disk Utility on all of the drives to verify and fix any problems.
When I initialized the wireless connections and initiated backups I connected to the imacg5 to the Time Capsule with an ethernet connection as well as via Airport and began 'backing up' my laptops, then started by backing up individually, various disks on my imacg5.
The laptops have rather small disks and backed up rather quickly. The imacg5 has hundreds of GB of data spread across several disks. I had decided to 'backup' the disks individually in case that had been the cause of my original problem.
My systems disk, Macintosh HD, backed up about 110 GB at the rate of 8 GBs per hour. I was encouraged.
My next 'data' disk, LaCie 320 #1, backed up about 209 GB at the rate of 2 GBs per hour. I was confused. This 'backup' took several days to complete. Once it completed, Time Machine has run about every hour as expected and completes the backup in about 3 minutes.
I still have two more disks on the imacg5 to backup. Does anyone have any idea what rate I should expect or should I just add the drives and let it take its course?

I say just do it!
When connected via ethernet I turn off the airport connection on the computer. I found that frequently my mom's macbook pro would choose the wireless connection to her Time Capsule rather than the ehternet connection to do the back up. This was slower than via the ethernet.

How to maintain time spec.of operations in routing and work centers

Similar Messages

Maybe you are looking for