How to make track work in both left and right speaker?

i have an audio track with 2 speakers that each had a lav mic on them. one was recorded into left channel and the other the right channel. so of course when i play back each of their voices only come out of one speaker. pretty new to audition so how do i fix the track so that they each come out of both speakers? TIA

I have to say that, although not uncommon, for TV it depends quite a lot on how things are shot. In a standard interview situation where you might have a 2-shot to establish (with a definite left and right position) then a close up of the interviewee then a cutaway of the reporter and so on, panning can become very confusing and it tends to be better to just put everything in the centre.
Radio is easier because you don't have to be aware of what pictures are showing--but, even there care needs to be taken especially since, as Steve says, a lot of listening is on ear buds or headphones which accentuate any panning. Even in radio, though, choices have to be careful...for example, let's say the host starts with an interview where he's panned slightly right and the guest slightly left. So far, so good. However, then the next two stories are just studio reads...does the host stay panned slightly right for consistency or does he move to the centre possibly causing confusion?
I'm not saying never give positioning clues in a radio or TV mix, just that you always have to be aware of the bigger picture.

Similar Messages

How to make mono recording play both left and right channels

I have an old mono recording that plays only on the left channel. How can I copy it to play on the right so I'll hear it on both channels? I put it on itunes and then tranferred it to Garageband in hope I could finally get it to play on both channels. I've tried everything in Garageband and nothing works. It seems simple to me, just duplicate the one channel to the other. Garageband says if you use the compressor it will play in both channels, but it won't. Any ideas? It's a recording from a band I was in back in 1966. We used state of the art reel to reel but it was mono! All these years I've tried to figure how to fix it. Thanks

I already recorded it from the tape to CD Spin Doctor through the line in and as I said it only comes out on the left channel. So then it's on itunes and I then transfer it to Garageband but it still is only on the left channel.I guess I could do this the old fashion way and get a mono plug to re-record to Spin doctor but in this day and age of sophisticated computer software I thought there may be an easier way. I guess I wasted my money thinking Garage band would help me edit this recording. Oh well, such is life!!!!

Flash cs3: how to make moving/scrolling photo menu left and right?

http://media.moma.org/subsites/2008/miro/flashsite/index.html
- click continue, then relative size link
How can I do this with lash cs3: how to make moving/scrolling
photo menu left and right?
When you move left and right and paintings move. and when you
click on a painting, you see the the title and it links to another
page on the site.

scene_mc start at x = -550... x wide is 2164 px
now I have this and its working...
navL_mc.addEventListener(MouseEvent.MOUSE_OVER, navL_Over);
navL_mc.addEventListener(MouseEvent.MOUSE_OUT, navL_Out);
function navL_Over(e:MouseEvent){
          if(scena_mc.x == 0){
                              scena_mc.x == 0;
          else if(scena_mc.x <= -10){
                              scena_mc.x += 10;
                              navL_mc.addEventListener(Event.ENTER_FRAME, runL);
function runL(e:Event):void{
          if(scena_mc.x == 0){
                              scena_mc.x == 0;
          else if(scena_mc.x <= -10){
                              scena_mc.x += 10;
function navL_Out(e:MouseEvent){
          navL_mc.removeEventListener(Event.ENTER_FRAME, runL);
navR_mc.addEventListener(MouseEvent.MOUSE_OVER, navR_Over);
navR_mc.addEventListener(MouseEvent.MOUSE_OUT, navR_Out);
function navR_Over(e:MouseEvent){
          if(scena_mc.x == -1164){
                              scena_mc.x == -1164;
          else if(scena_mc.x >= -1154){
                              scena_mc.x -= 10;
                              navR_mc.addEventListener(Event.ENTER_FRAME, runR);
function runR(e:Event):void{
          if(scena_mc.x == -1164){
                              scena_mc.x == -1164;
          else if(scena_mc.x >= -1154){
                              scena_mc.x -= 10;
function navR_Out(e:MouseEvent){
          navR_mc.removeEventListener(Event.ENTER_FRAME, runR);

How to change mono track on left only to mono track on both left and right

How do I change mono track on left only (coming out left speaker only) to mono track on both left and right (coming out both speakers)? Thanks!

http://www.bulletsandbones.com/GB/GBFAQ.html#leftspeakeronly
(Let the page FULLY load. The link to your answer is at the top of your screen)

Left click acting like both left and right click

Left Click button is acting like both left and right click button HP 2000 Notebook PC

Could you try to use another mouse? If the other mouse works perfect, then your mouse pad must be damaged and you should look to get it fixed or just use a mouse instead. If not, then the settings on how the clicks act must have been altered.
Try to find a mouse to try first before looking at the settings for your mouse pad. You could maybe borrow one if anyone else has a computer with a mouse in your home.
While you do that, I'll work on searching if this is common and if their is a solution if it's the software.
I'm a programmer and a computer expert in training.
Please feel free to click the "Kudos!" on the left if I helped. Note* I do not work for HP

How do I deal with audio, seperate left and right and make each stereo--CS5

I have a two mono mike recording which I can seperate into two seperate audio timeline tracks one is now left track in a seperate timline and the other is right in the other timeline, how do I make each of these tracks then into psuedo stereo tracks? Do I have to go to Soundbooth or is there a simple way in Premiere?

Bill G, tell me what I am missing and I'll use your method. I have what I think you are describing, and I don't understand the need to do anything special, if you use channel mapping.
I record a lav on one channel, and a different wireless mic on the other. When captured, I have a clip that PR would normally treat as a single stereo track.
BEFORE putting any clips on the timeline, select all clips and set channel mapping. Set each channel to mono. Now PR treats these as two mono tracks. The output for each mono is the master track, which in my project is stereo. I can change "volume" for each track in the mixer, etc. but each channel is provided to the left and right master output.
I didn't go back to sort out what you had, but if you had two stereo tracks, one each with a left and right channel only, I can see that you needed some other solution.

How to migrate stored procs accessing columns "LEFT" and "RIGHT"

Hello!
I have to migrate a SYBASE11-Database to Oracle 8.1.7.
How can I migrate Stored Procs that access tables that contain columns 'LEFT' and 'RIGHT'?
OMWB reports a parse error "encountered: ,". If ommit the words 'left' or 'right' or if I write 'left()' or 'right()', it works. But I have to use these columns and we cannot change the database model.
It doesn't work with quoted column names like this: "LEFT" or "RIGHT".
I use OWMB 1.3.1.0.0. Anybody any ideas? Thanks in advance.
Yours, Heiko Kaschube

This is a simple matter to fix.
As the words LEFT and RIGHT are treated as reserved words by the stored procedure parser, they cannot be used successfully as column names within Oracle PL/SQL.
In order to get the stored procedure to parse, you can append an underscore to all references to LEFT and RIGHT e.g.
left_
then right click on the stored procedure name and select 'parse procedure' from the drop-down menu. The procedure will now parse and the generated PL/SQL can be viewed within the Oracle model menu tab.
It will now be necessary to remove all the underscores previously appended to the words 'left' and 'right' from the PL/SQL version of the stored procedure in question. Again, this can be done within the Migration Workbench.
Hope this helps.

My HP pavilion G6 notebook PC the touch pad works however not left and right click pads

Hi all, new here so go easy with me ) I have a new HP pavilion G6 notebook PC, the touch pad works however not the left and right click buttons? Checked in control panel and can not find a way of enabling them. Also unable to scroll down a file in the window without using the actual scroll down bar on the right of the screen...any solutions please?

Hi Sy,
First, download the latest Synaptics driver installer on the link below and save it to your Downloads folder.
http://ftp.hp.com/pub/softpaq/sp53501-54000/sp53851.exe
Next, open windows Control Panel, open Programs and Features, right click the entry 'Synaptics Pointing Device Driver' and select Uninstall.
When this has completed, restart the notebook.
When windows has fully reloaded, open your Downloads folder, right click the Synaptics installer and select 'Run as Administrator' to start the installation. When this has completed, restart the notebook again.
Now follow the directions under the sub-heading 'Adjust horizontal and vertical scrolling' in the document on the link below to configure the scroll options as you require.
Configuring The ClickPad.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

How to make Vertical Text start furom left to right?

Sometimes some customers must be vertical text from left to right
This is mainly for Asian fonts
Whether it can be achieved with script,Or are there other methods？
Thank you~

@喜狼_edny – hm. Possible, but the result is somehow unsatisfactory.
See for yourself.
We could start with some text right aligned in a table with just one single cell:
We could rotate the cell to 270° like that:
Code:
var myCell = app.selection[0].tables[0].cells[0];
myCell.rotationAngle = 270;
And now we need the text direction from right to left and all characters rotated to 180°:
Code:
var myCell = app.selection[0].tables[0].cells[0];
myCell.rotationAngle = 270;
myProperties = {
    composer : "$ID/HL Composer Optyca",
    characterDirection : CharacterDirectionOptions.RIGHT_TO_LEFT_DIRECTION,
    paragraphDirection : ParagraphDirectionOptions.RIGHT_TO_LEFT_DIRECTION,
    characterRotation : 180
myCell.texts[0].properties = myProperties;
Result:
Ugh! Not exactly the result we expected…
(Tested with InDesign CS5.5 on OSX 10.6.8)
It's the characterRotation that is not working as expected.
Uwe
Message was edited by: Laubender

Mono 1 channel vocal file to both left and right?

hello, some how i recorded a vocal track and the vocal only appears on one channel, the left channel. i know it will still be mono but how can i convert it to sound on both the left and the right channel.. when i look at the wave. there is only waves above the zero line..
i hope i make sense

Thats so easy you are going to find it funny.
You are so right VOCAL is MONO. And you did record it correctly.
however on the bar,that shows the level-meter, when it plays, and its only on one-side,thats went its set on stero. Meaning it wil play stuff recorded like A SYN/DRUMMACHINE, these are just eg. Audio Midi INSTRUMENT.
Most like-ly to use that MODE/SETTING.
Then it will play in both LEFT $ RIGHT. Speakers.
However it should be on MONO mode for recording of VOCALS,
At this stage your at.
Even though, it will still play in righ and left speakers, after it has been RECORDED.
So here goes your answer.
ON THE BOTTOM OF THAT WAVE YOU SAW,
THERE IS, 2 CIRCLE IN A SMALL BOX
TO THE LEFT OF THE BOX THAT SHOWS THE REC- ENABLE.
THERE YOU WILL BEABLE TO SEE 2 CIRCLE IN A BOX.
NOW CLICK ON TO IT.
IT WILL THEN CHANGE TO 1 CIRCLE
THEN, THERE WILL BE ONLY BE ONLY 1 LEVEL SHOWING ON THE METER BAR. WHICH IS NOW SET TO MONO.
WHERE YOU WILL BE- ABLE TO SEE ONLY 1 CIRCLE AND ALSO 1 WAVE ON THE LEVEL-METER. WHERE YOU WILL SEE AND HEAR THE CHANGE IN MONO AND STERRO.
HOWEVER IT WILL STILL PLAY IN BOOTH R&L SPEAKERS, IN MONO.
DO HAVE FUN.
FR Blayzay.

How can I maximaze the screen into both left and right

I can change the text view of firefox; however, right and left hand side is still wide open. the screen is not full view.

You can use one of these extensions to set a default font size and page zoom on web pages:
* Default FullZoom Level: https://addons.mozilla.org/firefox/addon/default-fullzoom-level/
* NoSquint: https://addons.mozilla.org/firefox/addon/nosquint/

Probably a simple answer; centered links with floating link descriptions, both left and right of the links?

Attatched is an image of the requested result. I'm new to Dw so this might be an easy bit of code, but with research I haven't been able to find an answer.
Ideally, the numbers in the middle are links (centered on the page); and the text is a description of the link which floats to either side of the links, but is not necessarily centered; nor linked.
I would really appreciate the help of someone more knowledgeable. Thanks in advance.
The code I'm working on follows the image.
<!doctype html>
<html>
<head>
<meta charset="utf-8">
<title>design communications</title>
<style type="text/css">
body,td,th {
font-family: "Gill Sans", "Gill Sans MT", "Myriad Pro", "DejaVu Sans Condensed", Helvetica, Arial, sans-serif;
font-style: normal;
font-weight: lighter;
font-size: 10px;
color: #FB6145;
body {
background-color: #FFFFFF;
.strike {
text-decoration:line-through;
.links {
color: #FB6145;
text-decoration: none
a:visited {
text-decoration: none;
color: #FFA493;
a:hover {
cursor: none;
text-decoration: none;
a:active {
text-decoration: none;
.back-arrow{
color: #FB6145;
text-decoration: none;
font-size: 14px;
</style>
<link rel="shortcut icon" href="images/e_rimoldi_favicon_02.ico" type="image/x-icon" />
<style type="text/css">
</style>
</head>
<body>
<p><a href="question mark/prefix_0_0.html">? </a></p>
<p> </p>
<p> </p>
<p> </p>
<p> </p>
<p> </p>
<div class="links">
<p align="center">| <a href="works_03_01_perspective.html" id="01"
onmouseover=
"document.getElementById('02').className='strike';
document.getElementById( '03').className='strike';
document.getElementById( '04').className='strike';
document.getElementById( 'back-arrow').className='strike';"
onmouseout=
"document.getElementById('02').className='links';
document.getElementById('03').className='links';
document.getElementById('04').className='links';
document.getElementById('back-arrow').className='links';"
>01</a> |</p>
<p align="center">| <a href="works_03_03_plan.html" id="02"
onmouseover=
"document.getElementById('01').className='strike';
document.getElementById( '03').className='strike';
document.getElementById( '04').className='strike';
document.getElementById( 'back-arrow').className='strike';"
onmouseout=
"document.getElementById('01').className='links';
document.getElementById('03').className='links';
document.getElementById('04').className='links';
document.getElementById('back-arrow').className='links';"
>02</a> |</p>
<p align="center"> | <a href="works_03_02_section.html" id="03"
onmouseover=
"document.getElementById('01').className='strike';
document.getElementById( '02').className='strike';
document.getElementById( '04').className='strike';
document.getElementById( 'back-arrow').className='strike';"
onmouseout=
"document.getElementById('01').className='links';
document.getElementById('02').className='links';
document.getElementById('04').className='links';
document.getElementById('back-arrow').className='links';"
>03</a> |</p>
<p align="center">| <a href="works_03_04_mapping.html" id="04"
onmouseover=
"document.getElementById('01').className='strike';
document.getElementById( '02').className='strike';
document.getElementById( '03').className='strike';
document.getElementById( 'back-arrow').className='strike';"
onmouseout=
"document.getElementById('01').className='links';
document.getElementById('02').className='links';
document.getElementById('03').className='links';
document.getElementById('back-arrow').className='links';"
>04</a> |</p>
<div class="back-arrow">
<p align="center"><a href="works index_1.0.html" id="back-arrow"
onmouseover=
"document.getElementById('01').className='strike';
document.getElementById( '02').className='strike';
document.getElementById( '03').className='strike';
document.getElementById( '04').className='strike';"
onmouseout=
"document.getElementById('01').className='links';
document.getElementById('02').className='links';
document.getElementById('03').className='links';
document.getElementById('04').className='links';"
>«</a></p>
</div>
</body>
</html>

hey marty,
Perhaps this updated code will help clarify. I want the links to be centered on the page. But the link descriptions to float to either side? Does that make sense?
<!doctype html>
<html>
<head>
<meta charset="utf-8">
<title>design communications</title>
<style type="text/css">
body,td,th {
font-family: "Gill Sans", "Gill Sans MT", "Myriad Pro", "DejaVu Sans Condensed", Helvetica, Arial, sans-serif;
font-style: normal;
font-weight: lighter;
font-size: 10px;
color: #FB6145;
body {
background-color: #FFFFFF;
.strike {
text-decoration:line-through;
.links {
color: #FB6145;
text-decoration: none
a:visited {
text-decoration: none;
color: #FFA493;
a:hover {
cursor: none;
text-decoration: none;
a:active {
text-decoration: none;
.back-arrow{
color: #FB6145;
text-decoration: none;
font-size: 14px;
</style>
<link rel="shortcut icon" href="images/e_rimoldi_favicon_02.ico" type="image/x-icon" />
<style type="text/css">
</style>
</head>
<body>
<p><a href="question mark/prefix_0_0.html">? </a></p>
<p> </p>
<p> </p>
<p> </p>
<p> </p>
<p> </p>
<div class="links">
<p align="center">| <a href="works_03_01_perspective.html" id="01"
onmouseover=
"document.getElementById('02').className='strike';
document.getElementById( '03').className='strike';
document.getElementById( '04').className='strike';
document.getElementById( 'back-arrow').className='strike';"
onmouseout=
"document.getElementById('02').className='links';
document.getElementById('03').className='links';
document.getElementById('04').className='links';
document.getElementById('back-arrow').className='links';"
>01</a> | meddling</p>
<p align="center"> kongenshus | <a href="works_03_03_plan.html" id="02"
onmouseover=
"document.getElementById('01').className='strike';
document.getElementById( '03').className='strike';
document.getElementById( '04').className='strike';
document.getElementById( 'back-arrow').className='strike';"
onmouseout=
"document.getElementById('01').className='links';
document.getElementById('03').className='links';
document.getElementById('04').className='links';
document.getElementById('back-arrow').className='links';"
>02</a> |</p>
<p align="center"> | <a href="works_03_02_section.html" id="03"
onmouseover=
"document.getElementById('01').className='strike';
document.getElementById( '02').className='strike';
document.getElementById( '04').className='strike';
document.getElementById( 'back-arrow').className='strike';"
onmouseout=
"document.getElementById('01').className='links';
document.getElementById('02').className='links';
document.getElementById('04').className='links';
document.getElementById('back-arrow').className='links';"
>03</a> | design communications</p>
<p align="center"> green river | <a href="works_03_04_mapping.html" id="04"
onmouseover=
"document.getElementById('01').className='strike';
document.getElementById( '02').className='strike';
document.getElementById( '03').className='strike';
document.getElementById( 'back-arrow').className='strike';"
onmouseout=
"document.getElementById('01').className='links';
document.getElementById('02').className='links';
document.getElementById('03').className='links';
document.getElementById('back-arrow').className='links';"
>04</a> | utah</p>
<div class="back-arrow">
<p align="center"><a href="works index_1.0.html" id="back-arrow"
onmouseover=
"document.getElementById('01').className='strike';
document.getElementById( '02').className='strike';
document.getElementById( '03').className='strike';
document.getElementById( '04').className='strike';"
onmouseout=
"document.getElementById('01').className='links';
document.getElementById('02').className='links';
document.getElementById('03').className='links';
document.getElementById('04').className='links';"
>«</a></p>
</div>
</body>
</html>

How to add two different background images - left and right

I want to get something like this

The way I have done that is to create the right image as a full width image and then place the left hand image over top and stretch the image to the left hand side of the page.
Use background images on boxes instead of page background. I have done something similiar in the header of this site:
http://www.signalpointdining.ca

How to make transitions work in reverse when backing up thru slides?

I'm new to keynote '09. I like the transition builds, like "Mirror", but I was surprised that they seem (by default) to only work in the forward direction.
If I hit the back arrow on my Apple Remote, I get a plain transition.
The effect I'm using is "Mirror". How can I make it work going both forwards and backwards with my remote? Thank you!

Hi Liang,
I tested a simple code with DAQmxSetDigitalLogicFamilyPowerUpState function and I did not run into any errors.
Refer to the attachment. The code simply writes 1s to port 0 and sets the Power Up state to 2.5V. Dev27 is my NI 6537 device.
Here is the software I have installed on my machine: Windows 7 (32-bit), Visual Studio 2010, NI DAQmx 9.6
Hope this helps!
Mikhail
RF Toolkits, Product Support Engineer
National Instruments
Attachments:
WriteDigPort_PowerUP.c ‏3 KB

HT5559 JAVA WITH CHROME!!! I am trying to login to my bank account at nordea.dk. This website uses somekind of java thing. Chrome cant't load it. Works perfect with Safari. How to make it work in Chrome?

I am trying to login to my bank account at nordea.dk. This website uses somekind of java thing. Chrome cant't load it. Works perfect with Safari. How to make it work in Chrome?

Do you speak of true blue Java or Javascript? If the latter then it is a problem with the Browser.
But if it is the real Java, do you have the offical version of Java from Oracle installed?
Getting applications to see official Java is a nightmare. If you install the Runtime Environment only (JavaRTE) most applications do not see it.
To force offical Java system wide, I found you have to install the Java Developer Kit (JavaJDK). It's a larger install as it also comes with documentation and compilers but it make offical Java system wide.

How to make track work in both left and right speaker?

Similar Messages

Maybe you are looking for