How to monitor modules
Hi,
i am trying to run a message using a module that i deployed to the WAS.
the message paases the incoming adaptor (it is green in the adaptor monitoring) , however then it fails probably , i cant see in the message monitoring any feedback.
SO i guess the module fails.
My question is how can i monitor the module , where can i see if there is a java exception etc....
Udi
hi Udi,
Have u written any Audit log statements in your module, if so then check the Message Monitoring. You just check Error log also in Message Monitoring.If u don't know how to use Auditlog see the example here. Just do slight modification depending on whether u r using it on inbound side or Outbound side. Just change to AuditDirection.Outbound .
obj = inputModuleData.getPrincipalData();
msg = (Message) obj;
amk = new AuditMessageKey(msg.getMessageId(), AuditDirection.INBOUND);
Audit.addAuditLogEntry(amk,AuditLogStatus.SUCCESS,"CreatePdfBean is called");
Regards,
Gowtham K.
Similar Messages
-
How to monitor modules in Cat6500?
Hello,
my question is: how can I monitor the status of modules in CAT6500 through SNMP? Does anyone know the correct OIDs for doing that?
Thanks in advance.You can get module status using the moduleStatus object from the CISCO-STACK-MIB. The moduleTable in this MIB will provide the module type, firmware, model, etc. in addition to the status.
-
How to monitor a VIP's performance?
Could I get any advice regards how to get the statistics of a VIP performed and how to monitor it?
Any comments will be appreciation.
Thanks in advance.Hi Gilles,
How much is too much? :-)
We are monitoring parameters like flows/second and active local connections but I have been looking at parameters telling us how far we can go before seeing performance decrease.
We are terminating SSL on the CSS and if about 800 SSL sessions per seconds per SSL module is the limit, what would be a good parameter to watch?
I couldn't find anything in the MIBS that tell us how many SSL sessions/sec are served.
Any help would be greatly appreciated :-)
Thanks,
Fabrice -
How to monitor a specific transaction in Solution Manager ?
Hi all,
I have configured the Service Level Reporting and it works correctly.
But i don't know how to monitor a specific transaction like SM21, DB02, FB01N etc... ?
In the SL Reports configuration steps, we can configure this option : Select Business Processes For SL Report. I did a lot of tests but it does not work.
Have i to configure the Business Process Monitoring ?
Thanks.Hello,
it depends a little on what you want to do. If you use the pure CCMS monitoring with the table ALTRAMONI you get average response time per instance and you only get new measurements once the status changes from green to yellow or red.
In order to get continuous measurements you should look into Business Process Monitoring and the different documentations under https://service.sap.com/bpm --> Media Libary --> Technical Information. E.g. the PDF Setup Guide for Application Monitoring describes this "newer" dialog performance monitor. Probably you have to click on the calendar sheet in the Media Libary to also see older documents as well. As the Business Process Monitoring integrates with BW (there is also a BI Setup Guide in the Media LIbrary) you can get trendlines there. This BW integration also integrates back with SL Reporting.
Some guidance for SL Reporting is probably given under https://service.sap.com/rkt-solman but I am not 100% sure.
Best Regards
Volker -
How to monitor an application using JMX
Hi,
How can I monitor the portal application running on portal server by using MBeans (JMX)? For this I need to make a connection between my portal application and MBean class, How to monitor operations? How can I do that? If anybody has come across the same requirement pls explain me with the implementation details.Hello,
I have done that in a project (not Portal, but pure Java Application, should be no difference), working fine.
The steps are as follows:
- create MBean Server (e.g. MBeanServerFactory.createMBeanServer("test");)
- create your MBeans
- make them accessible to clients (register the MBeans in the server)
- query them from clients
see http://java.sun.com/developer/technicalArticles/J2SE/jmx.html
for very good explanation including sample source code.
CSY -
How Many Memory Modules (1 or 2) Come Pre-Installed in HP Envy Touchsmart m7-j120dx?
I know my HP Envy Touchsmart m7-j120dx came preinstalled with 8GB of RAM. I purchased it last year from Best Buy. Haven't taken the back off of the laptop just yet and it's at home while I'm at work, but wanted to see if anyone can verify *how* the standard 8GB of RAM is in there at present? Two 4GB memory modules or a single 8GB memory module?
I'm trying to place an order online this afternoon to upgrade the laptop to 16GB of RAM and I'd like to know if I need to order two 8GB memory modules or just a single 8GB memory module, depending on exactly how many memory modules are in the laptop at present to make the existing 8GB of RAM I'm running.
Thanks if anyone knows the answer to this.Okay, one more question...
The memory in my laptop came pre-stalled with 8GB of it, with the characteristics of 1600Mhz and DDR3L PC3-12800.
Replacement memory (16GB) recommended by Crucial.com for my system has 1866Mhz instead of 1600Mhz, and is DDR3L PC3-14900.
What was recommended has of course slightly higher specs of the memory than what's currently running in my system for an additional $23 over just replacing the memory with 16GB of RAM having the identical 1600Mhz and DDR3L PC3-12800 specs.
Can my HP Envy TouchSmart m7-j120dx actually do anything as far as increased performance in going with the 1866Mhz and DDR3L PC3-14900 memory or would my laptop continue to "dumb the memory down" to 1600Mhz and DDR3L PC3-12800 specs and not be able to utilize the enhanced specs of 1866Mhz and DDR3L PC3-14900?
Just trying to spend my money wisely. Thanks for any additional clarification. -
How to monitor OSD TS failure and get alert or report?
How to monitor OSD TS failure and get some alert or generate an report?
We have SCCM 2012 R2 CU1 with MDT 2013.
I have checked the OSD reports in SCCM and everyone is emty, where do SCCM get data to the what to activate?
(I thinking of "Task Sequence - Deployment Status" reports)
I am not sure people read report manually or lock at the MDT monitor view. So best I think that generate an email or incident in Service Manager when an TS fails.
We do have SCOM, SCSM, SCO.
Is there anyone that can point what way or what option I have?
/SaiTechSpecifically you could use this Status Message Query syntax to monitor your Task Sequences for errors:
select stat.*, ins.*, att1.*, att1.AttributeTime from SMS_StatusMessage as stat left join SMS_StatMsgInsStrings as ins on stat.RecordID = ins.RecordID left join SMS_StatMsgAttributes as att1 on stat.RecordID = att1.RecordID inner join SMS_StatMsgAttributes
as att2 on stat.RecordID = att2.RecordID where att2.AttributeID = 401 and att2.AttributeValue = "DOJ200A1" and stat.SiteCode = "DOJ" and att2.AttributeTime >= ##PRM:SMS_StatMsgAttributes.AttributeTime## order by att1.AttributeTime desc
Just replace DOJ200A1 with the Deployment ID of your Task Sequence and DOJ with your SiteCode.
If you want to generate an alert if the TS fails then you could run a script that calls a utility (or similar) which sends a pre-configured email to a specified address (as an alternative to Torten's response). This could be placed in the built in error
logging section of the SCCM integrated MDT Task Sequence when it fails which I assume you are using (right at the bottom, called Gather Logs and StateStore on failure).
There are heaps of ways of generating an email from a TS and controlling error logging just do a search - as you have Service Manager you could even use your instance of Orchestrator and call a run book in your TS which does the email?
Cheers
Damon -
How to monitor disk space in BW
can some body help me out on the following issues.
1)How to monitor disk space in BW?
2)How can I delete Application logs in BW?When I research with DB02 transaction code in BW, I encountered following tables having lot of log , please some body can help me, how to delete the following log data?
ARFCSDATA ARFC Call Data (Callers)
BALDAT Application Log: Log data
BSRWBSTORE Storage for binary large objects (Excel) -
How many monitors can you use on a new imac with GEForce 780m?
My husband bought a new 27" iMac with the optional GEForce 780m with 4 gig of video ram. He wants to know how many monitors he can run simultaneously, and at what resolutions. He would obviously be using the Thunderbolt ports to do this. I thought this information should be easily found in the technical specs for either the iMac or the video card itself on the NVidia site, but it is not.
Catherine Gramze wrote:
Ok, rkaufman. Can he use two 4k monitors in addition to his iMac display? He wants to know what his options are in terms of number of monitors and the resolution. Yes, I know which monitor you buy will be the limiting factor for the actual display, but he has not yet purchased these additional monitors. If thunderbolt allows him to run 3840x2160, how many of them can he run at once at 32 bpp? How many if he chooses 2560x1600 instead?
To be honest I don't know how many Thunderbolt displays he can run, I would STRONGLY recommend contacting Apple to ask. You can ask the online store (phone number is in upper right of it's home page) or if you have an Apple Store in your area, making an appointment with a business specialist and asking that question. -
How to monitor all SAP Server through solution Manager?
Dear Friends,
How to monitor all SAP Server through solution Manager?
Is it possible if yes then how? Please forward configuration and transaction also.
Please help me as early as possible..
Thanks,
Regards,
SachinHi sachin,
You can monitor your sattilite systems through solution manager.
If you want to monitor systems in solution manager means you need to configure those systems in solution manager.
Before including the systems in solution manager we need to create a solution using tcode <b>DSWP</b>.
After that you can include the systems using tcode <b>SMSY</b>.
For configuring the systems we have lot of phases its very difficult to explain here.
Try to login to<b> service.sap.com</b> and <b>help.sap.com</b> find the helpfull guides.
i hope it will help you.
any issues post it.
kiran kumar.v -
How to monitor oracle 11g database sessions on Windows 2008 server?
Hi Experts
How to monitor the Oracle 11g database sessions on Windows 2008 server (other than SQL Developer tool), which procedure or query is taking more time with Java application.Recently i found this tool- myorasql on the net to monitor the performence of database, easy to setup and check the performence. i never tested it but seems impresive. It is free and i think it would be use ful to you.
http://myorasql.com/
You can also use Quest - Toad or sqlplus if you are very good at sql commands and all dictionary tables or OEM/EM grid if it is configured . -
How to monitor partial payment
Dear All:
In my case, I always pay more money for original AR because I forgot partial payment had been done before. How I monitor AR overpayment when past partial payment exist?
Thanks for the help suggestion first. Sorry for error description above.
1.first for specific overdue analysis policy of company, we use partial payment.
2.And then the question comes. According to contract item, we send invoice to customer only once and receive payment in several step. Each time income received, we use partial payment to clear the AR (to relate payment with original AR). But one customer may have some contracts with us, it always pay for all contract in certain amount at one time. We shall manually divide amount for each contract. If user forgot one contract was paid partially before, he may clear the AR totally at sencond time and then the first payment will still outstanding in open item. Finally we can find many partial payments received but can't refered to any invoice.
So we are finding a way to control AR clearing to check whether partial payment exist and if the total amount is over original invoice it couldn't be cleared.
Thanks to give me some suggestion.
Message was edited by:
Tommy shi
Message was edited by:
Tommy shi
Message was edited by:
Tommy shiHi...
You always have the otion of displaying vendor/customer balances(FK10N/FD10N) to find out the balances and the vendor/customer line items(FBL1n/FBL5N)
When you pay your vendors select residual payment so that the system will select the residual item remaining to be paid to avoid any confusion.
Its a good business procedure that you should not be paying your vendors more unnecessarily.
Regards
Aravind
Assign points if useful -
How to monitor MySQL Server installed in Windows Server using Nagios
You can do this via NSClient as Gary posted. The NSClient is a communications system that allows nagios to send commands to a target system over the nsclient protocol and they are executed on the remote system. You will still have to build some kind of vbscript or plugin to run on the target system to do the actual query to check on mysql.There are other options to. If you enable snmp on your target computer you can use a few nagios plugins to query the snmp agent on the target computer to see if a service is running. To do this via snmp you will need this plugin "check_snmp_process.pl" fromthis site.Your check command will look something like this:check_win_process:= check_snmp_process.pl -H $HOSTADDRESS$ -C "$USER6$" -n "$ARG1$" -w $ARG2$ -c $ARG3$The service definition will be like this:check_win_process!sqlservr!0!0This will check...
I installed Nagios Core in my Ubuntu workstation 10.04 for me to learn something new in my craft. I use this now to monitor our Windows Server 2008 with MySQL server installed as well as our Datalink Switch (DGS-1210-24). I searched on google on how to monitor a MYSQL server installed in Windows server using Nagios Core but i could not seem to find any. Could anybody who's expert in Nagios give me steps on how to do so. Thanks. All i found in google were steps in monitoring mysql installed in linux and nothing in windows server.
This topic first appeared in the Spiceworks Community -
How to monitor RFC processing in XI
Hi Friends,
In the IDoc to RFC scenario please tell me How to monitor RFC processing in XI..
Thanks and Regards
SriSri,
You can monitor in SXI_MONITOR/SXMB_MONI. If its Syncronous then u can see the request and response messages in the above mentioned transaction.
To get more details you can go for RWB and select ur message and check for audit log's.
Best regards,
raj. -
How to monitor page hit rates?
I see a lot of references in docs and white papers to cache hit rates for the Parallel Page Engine, but I've not found any documentation on how to monitor this system-wide (only how to turn on portlet statistics and get a manual page-by-page look at cache success/failure).
Is there any way to determine the cache hit rate for the PPE?Stephen,
I'm sorry you seem to be experiencing some problems with the support and documentation of the portal software.
The link above was posted on May 1st 2002, and was posted as an absolute link rather than a dynamic product link. As the document name is revved the link will change, hence why an old link from the forums will no longer work.
The document you seek is here. I assume that by referring to webcache you mean that when you add the XLF logging format options webcache complains about x-ecid (for example). This indicates that you have not applied the core iAS patchset which is required to allow webcache to understand these extended log parameters. I believe that the document refers to this as a requirement to get 'full functionality' - perhaps that is a little esoteric, I'll change it in the next rev.
If you continue to be unsuccessful in deploying this note please let me know what errors you're seeing and I'll see what I can do. I'm working on an end-to-end performance kit at the moment that will supercede this document so I'll take your comments on board when revving this area.
Regards
Jason Pepper
Principal Product Manager
Oracle9iAS Portal
Maybe you are looking for
-
Dear PP-PI Expert! I already searched many forums on internet about this subject, but i have not got any answer about this issue I want to collect the pp-pi datas which is inputed into SAP system with TCODE CO54, CO53,CO60, The follow process is: 1.G
-
How to increase the size of text boxes in FCPX without stretching the text inside?
How to increase the size of text boxes in FCPX without stretching the text inside?
-
Selection of range in variable
Hi Gurus I have following requirment regarding the selection in variable. We want to populate the exit variable on the employee and populate it with the all the employees in the cube for particular fund center based on the fund center selected in the
-
Referencing cells in a closed numbers documnet
I am trying to find a way to link cells from multiple numbers documents, even if they are closed. I do not want to combine the documents. I know this can be done in excel. I create a schedule with numbers and I want to keep daily, weekly, monthly and
-
How to save the selection of quick select tool using scripts?
I am writing a script to record the edit history and I want to save the select area of quick select tool using scripts.