How to mount a remote folder with VPN

Dear All,
I setted up a mac mini server with VPN. It goes through a rooter and I open some ports to be able to connect with VPN.
From max MacBook pro, I installed the VPN profile and I can connect the VPN to my remote server. The remote server has a public static adresse.
Now I am connected with VPN, but I can not moiunt a remote folder. I press command+K and I entered:
afp://username@ip-adresse/Groups
But it return an error message
"There was a problem connecting to the server "46.xx.xxx.xx".
The server may not exust ot it unavailbale at this time. Check the server name ot IP address, check your network connection, and then try again
But the server is up and reachable!
Thank a lot for your advises.
Cheers

I even tryed with
afp://ip-adress
after being connected with VPN,
Should do something else from my router?
When I go to my Macbook system preference and the to network and look at my location, I can see a green label to the VNC and and a IP adress is provided my the VNS server which belong to the pool I configured and out of the local pool

Similar Messages

How to connect to remote server with jmx from jvisualvm

I have a WL 10.3.2 domain running on a single box. The adminserver and managed server are running on the same box, on different ports (7001 and 8001, respectively).
I have a Spring application deployed to the managed server and I've configured it to register a Spring bean as a JMX mbean.
When I run this entire configuration on my laptop, I can run jvisualvm and connect to my server and see and manipulate my registered mbean.
I'm having trouble figuring out how to get a remote connection working, however. I want to run jvisualvm on my laptop and connect to the remote server.
I first did "Add Remote Host", where I specified the IP address. It appears that this was created successfully, and it apparently was able to determine the DNS name for it.
I then tried to add a JMX connection. In the "Connection" field, I just entered the IP address followed by a colon and 8001 (managed server port number).
In the "Use security credentials" section, I entered the weblogic admin principal and credentials.
When I click OK, it chugs for a while and eventually gives up, saying:
Cannot connect to [email protected]:8001 using
service:jmx:rmi:///jndi/rmi://nn.nn.nn.nn:8001/jmxrmi
What might I be missing?

I've resolved this. At least I was able to configure an authenticated connection. It doesn't use SSL yet, but I'm ok with that for a while.
Resolving this only required changing the command line parameters for the managed server, and being aware of the "jmxremote.access" and jmxremote.password" files. The following blog article helped a lot: [http://www.dzone.com/links/r/monitoring_your_java_application_with_jmx_part_2.html] .
I'm now passing the following command-line parameters:
-Dcom.sun.management.jmxremote -Dcom.sun.management.jmxremote.port=8888 -Dcom.sun.management.jmxremote.ssl=false -Dcom.sun.management.jmxremote.authenticate=true
The default "role" configured in "jmxremote.access" is "controlRole", and the "jmxremote.password" file specifies the credentials for that principal. I simply used that principal and credential in JVisualVM, and the connection succeeded.
And I just used the "host:port" form, not the protocol form.
Edited by: david.karr on Feb 4, 2011 12:47 PM

How can i protect a folder with a password so everytime i want to open it it requires my password?

how can i protect a folder or application in iPad with a password so everytime i want to open it it requires my password?

No way to do so at this time.

How can I save a folder with pictures in it, on PC or MAC? (Not Camera Roll)

Dear Apple Community,
I want to save a Folder with pictures in it, that I created from the iPhone.. these photos (and videos) are available only in this folder and I don't want to loose them at all!
Whatever, how can I save this folders on my mac? and/or PC? And I don't mean the camera roll folder! Just this folder that I created on the iPhone.
Thanks in advance for you anwers!
Best Regards,
Luke

Not supported by Apple. The only photos that can be imported from an iPhone are photos in the camera roll.

How to login the remote desktop with user id and password using coded ui

we are using vs 2013, we have automated some automated test cases using coded ui. i have on problem while i am running the those test cases in remote system. here the scenario is "after executed one test case we need to restart the system. After restarted
I have to login the remote system with user credentials to continues execution for the remaining test cases." it is very helpful to me.. so please guide me how to overcome these problem?
Thanks in advance ...

Hi Divakar,
As far as I know, there isn’t this feature of remote test in VS2013.
I suggest that you could submit this feature request:
http://visualstudio.uservoice.com/forums/121579-visual-studio. The Visual Studio product team is listening to user voice there. You can send your idea there so the others can vote it. If you submit this suggestion, you might post that link here which will
benefit others who has the similar issue
Regards
Starain
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

How to set up KM folder with Anonymous access.

Experts,
I would like to setup a KM folder with anonymous access where any document on that folder can be viewed by anonymous users by clicking on a link specific to that document. For example: http://server/irj/go/km/docs/documents/TechDocs/file_name.html
Please note that this document will not be rendered through an iView, so setting up an anonymous role will not work in this case.
Can anyone tell if this will be doable and the steps to do it?
Thanks in advance for your help.
Regards,
Abu

Hi Abu,
> How can I just give access to a specific folder under /irj/go/km/docs?
You have to differentiate between anonymous access to the iView behind /irj/go/km/docs (PCD auth scheme) and the permissions on KM folders (KM permissions). If you want to restrict the access, on the folders which should not be accessible for anonymous access, remove the group "Everyone" from the permissions (via details / settings / permissions). For details see http://help.sap.com/saphelp_nw04/helpdata/en/1b/12c49eb27011d5993800508b6b8b11/frameset.htm
Hope it helps
Detlev

How to synchronize just one folder with bookmarks?

Is there any way how to synchronize just one particular folder with bookmarks between different PC? I have found a several options how to synchronize all bookmarks between PCs, but none of them has the option to pick just one particular folder.
Can you help?

No, it is all or nothing. You can't select which bookmarks folders to sync.

How can i zip a folder with use of webutil

hi,
We are using forms 10g and weutil 1.0.6.Is it possilble to zip and extract a folder with use of the webutil
our requirement is take current day folder, zip that filder and upload that file
second requirement is extract the uploaded zip file
if anybody know thanks in advance
mathew

most of the zip-tools can be started via parameter. So you have to read the readme's of those tools and start it in the background with the appropriate parameters

How to burn DVD including folder with photoes

I need to make common DVD with video_ts folder and add a folder with photoes to watch on computer and print them lately.
Which soft can do that?

tons of software can do that both free and paied
both from app store and from other sources
free options
burn from app store you could check out
and dvd styler

How to debug Injected remote thread with symbols (not a DLL just a thread)

I am trying to debug my injected code assignment(code injected into explorer but for the porpose of my research assignment it can be any 3rd party code). I am able to connect to my VM(remotely with a remote debugging monitors) and attach to my breaking thread
(int 3) inside explorer, but I can only see my code as dis-assembly code. I need to see my source code (have the debugger look for it for that offset/thread).(I believe i have all the pdbs stored correctly on the other system as I was able to debug an "injected"
dll module with its source code,(after attaching to that process of-course)
I want to debug my Injected code with my source code, (not an injected dll!). so my question is: 1. is it possible to debug with source code a remote create thread ?(CreateRemoteThread)
any other issue with this when trying to do it remotely ? (I'm doing a remote debug with msvsmon.exe) ? or can I connect the source code my self in any way ? can a build with .bsc file make any different in helping the debugger find the source code of my
injected thread ?
Please any thoughts anyone ??
Thanks

JFYI Windbg:
Debug-info can be loaded for whole - memory-mapped - modules ('sections' start at 'expected' RVAs), copied manually (WriteProcessMemory) into address space of a process
using '.reload /f module=address' (module then shows up in loaded-module-list 'lm'):
Write image of module to file:
CommandLine: "C:\Users\sammy\Documents\Visual Studio 2010\Projects\Injector\Debug\Injector.exe"
Symbol search path is: C:\Windows\symbols\dll;srv*C:\Symbols\MsSymbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
ModLoad: 00f10000 00f2b000 Injector.exe
ModLoad: 77260000 77388000 ntdll.dll
ModLoad: 76ff0000 770cd000 C:\Windows\system32\kernel32.dll
ModLoad: 6a490000 6a603000 C:\Windows\system32\MSVCR100D.dll
(e6c.1390): Break instruction exception - code 80000003 (first chance)
eax=00000000 ebx=00000000 ecx=0024f778 edx=772c5d14 esi=fffffffe edi=00000000
eip=772a878e esp=0024f790 ebp=0024f7c0 iopl=0 nv up ei pl zr na pe nc
cs=001b ss=0023 ds=0023 es=0023 fs=003b gs=0000 efl=00000246
ntdll!DbgBreakPoint:
772a878e cc int 3
0:000> .writemem c:\temp\injector.exe 00f10000 00f2afff
Writing 1b000 bytes......................................................
Allocate memory in other process, copy image, load pdb:
CommandLine: "C:\Users\sammy\Documents\Visual Studio 2010\Projects\VectorWindbg\Debug\VectorWindbg.exe"
Symbol search path is: C:\Windows\symbols\dll;srv*C:\Symbols\MsSymbols*http://msdl.microsoft.com/download/symbols
Executable search path is:
ModLoad: 00a40000 00a68000 VectorWindbg.exe
ModLoad: 77260000 77388000 ntdll.dll
ModLoad: 76ff0000 770cd000 C:\Windows\system32\kernel32.dll
ModLoad: 6a490000 6a603000 C:\Windows\system32\MSVCR100D.dll
ModLoad: 6a3d0000 6a487000 C:\Windows\system32\MSVCP100D.dll
(15cc.8c0): Break instruction exception - code 80000003 (first chance)
eax=00000000 ebx=00000000 ecx=0022f418 edx=772c5d14 esi=fffffffe edi=00000000
eip=772a878e esp=0022f430 ebp=0022f460 iopl=0 nv up ei pl zr na pe nc
cs=001b ss=0023 ds=0023 es=0023 fs=003b gs=0000 efl=00000246
ntdll!DbgBreakPoint:
772a878e cc int 3
0:000> !sym noisy
noisy mode - symbol prompts on
0:000> .dvalloc 1b000
Allocated 1b000 bytes starting at 00050000
0:000> .readmem c:\temp\injector.exe 00050000 L0x1b000
Reading 1b000 bytes......................................................
0:000> .reload /f injector.exe=00050000
DBGHELP: c:\windows\symbols\dll\Injector.pdb - file not found
DBGHELP: c:\windows\symbols\dll\exe\Injector.pdb - file not found
DBGHELP: c:\windows\symbols\dll\symbols\exe\Injector.pdb - file not found
SYMSRV: c:\symbols\mssymbols\Injector.pdb\FE691049676443688BDF84F0EEE965552\Injector.pdb not found
SYMSRV: http://msdl.microsoft.com/download/symbols/Injector.pdb/FE691049676443688BDF84F0EEE965552/Injector.pdb not found
DBGHELP: injector - private symbols & lines
C:\Users\sammy\Documents\Visual Studio 2010\Projects\Injector\Debug\Injector.pdb

How to create a new folder with a different name everyday

Hello everybody,
I have another question if you don't mind. But first thank you again to V.K and red menace for helping me with the my previous post.
This is actually the same project, I just keep on seeing new obstacles when I'm almost done.
Below is my workflow. My workflow is exporting a quicktime movie to a folder in our server.
What I need to do at the end is to move the exported file into a folder but a folder needs to be created and it has to change at about midnight everyday.
For example today the file will go to Server>Client folder>File folder named 09-04-2008
Then the next day, I need to put the new exported files to Server>Client folder>File folder named 09-05-2008.
First, how can I create a sequential named folders and second how can I tell Automator to put the files in the right folders. This process is a 24 hour process.
Thanks for you future help.
Helmut
1) Get Specified Finder Items (Pointing to File Folder)
2) Get Folder Contents (tried checked and uncheck on Repeat for each subfolder
3) Get Specified movie ( I guess Filter finder items and choose .mov will work too)
4) Quicktime Export (exporting it to the Exported Folder)
5) Get Specified Finder Items (Pointing to File folder to get to the original file)
6) Get Folder Contents
7) Filter Finder Items (choose .mov)
8) Move Finder Items ( pointing to Archive Folder to move the original file)
9) Get Specified Finder Items (Pointing to Exported Folder)
10) Get Folder Contents
11) Filter Finder Items (.mov)
12) Move Finder Items (Pointing to Server Folder)

It doesn't look like there is an easy way to do this. The sort and filter actions don't let you use variables, and I haven't found any actions that will alter a list. Making a text file with the name of the newest folder seems kind of clunky, but it is an option.
What I was thinking about was an action that would take the first item in a list - then you could get your backup folders, sort by creation date, and just take the top one in the list (the newest one). Hmmm - this should be fairly straight-forward, so maybe I'll write an action
In the mean time, give the Run AppleScript action in the following workflow a try.
Tested workflow:
1) Ask for Finder Items (Type: Folders)
2) Get Folder Contents
3) Sort Finder Items (by creation date in ascending order)
4) Run AppleScript (the following script)
<pre style="
font-family: Monaco, 'Courier New', Courier, monospace;
font-size: 10px;
margin: 0px;
padding: 5px;
border: 1px solid #000000;
width: 720px;
color: #000000;
background-color: #FFDDFF;
overflow: auto;"
title="this text can be pasted into an Automator 'Run AppleScript' action">
on run {input, parameters}
return the first item in the input list
input: a list of anything
output: the first item, or {} if none or error
set output to {}
try
set the end of the output to the first item of the input
end try
return output
end run</pre>
5) View Results
The above workflow should return the newest item in the selected folder.

How to highlight the entire folder with the tag color, as before?

I've always highlighted important folders with colors, so that they stand out among others in a list for quicker access. Now in Mavericks list view, there is only a small color dot to the right of the folder's name (sometimes very far from the folder's name if the column is large). As a result, it is much harder to pick important folders. Is there any way to apply the tag color to the whole folder, as it used to be in all previous systems? Or at the very least, to move the dot to the left of the folder name within lists, as in Icon view? I really hope Apple did not remove this feature simply for the sake of design. Thanks.

mistersquid, S. G. is actually referring to the new Tags feature in Mavericks. This replaces entirely the Labels feature in previous versions of the OS, as far as I can tell.
Labels would let you apply a color highlight to a folder. It would appear as a color behind the entire row.
With Mavericks, however, Labels are gone and are replaced with Tags, which just puts a small colored dot off to the right of the folder name (and it's always like this, not just when you click on the folder), and some of these aren't distinct enough from one another (i.e. purple and gray look almost identical if you're scrolling through a series of "gray" folders pretty quickly—you may miss that one purple dot). Also, like S. G. mentioned, these can be pretty far off in your periphery if you've got long folder names, so this just adds another level of "hard-to-see-ness" (it's a technical term ).
I'm a graphic designer and I have been using Labels to colorize my job folders according to their current status. For example:
No label = job is open/in progress.
The next color schemes were more of a "stop light" effect, going from red to green:
Red = job is approved. Prep final files and send to printer/client.
Yellow = job is done. Prepare job ticket/calculate time for billing.
Green = job is done and job ticket is ready to go (hence the green color) to my co-worker for billing/invoicing.
Gray = job is finished/billed/closed (i.e., I've "grayed it out").
Purple = job transferred to another co-worker (i.e., I got too busy and they're working on it now). This one is a rarer color, and with Tags it's a bit difficult to discern one or two purple (more like a light lavender) dots in a sea of gray ones.
I agree with S. G. and would love to see a stronger means of identifying the status of a project at a glance reappear—perhaps as a selectable alternative to Tags in the Finder preferences (because I can definitely see how the two means of colorizing a folder could compete with one another), like a checkbox to the effect of "Use Labels instead of Tags," similar to the "Open folders in tabs instead of new windows" option.
Feedback submitted. Thanks, yodathejedi, for the link.
Message was edited by: Xiebinrui -- oops, duplicated word. Fixed!

Creative Zen Vision 30GB - How to set IR Remote ON with Navigation keys not working in the play

I have Creative Zen Vision 30GB player. Within a month of buying, its navigation keys stopped working. I took it to the customer service of store where I bought it and they fixed it (their solution was to make firmware update, even though I do not understand how come that can fix this issue). Anyways after another 5 months of not so often use, the same problem returned (key pad stopped working and without it this player is useless). I sent it to Creative and they returned it saying that as it has few scratches on the edges, they believe it has been hit. I never dropped the player and these are normal scratches at the end if you do not use any skin (which I could never find for this player). Btw from my other friend's experiences, Creative always does like this, never considered warranty (so beware!). Anyways now the problem is that I have IR remote for Zen vision but it can not work till IR Remote setting in System->Player Settings is switched ON. And this can not be done as the navigation keys are not working. So please please suggest me some other way if anybody of you know to enable this setting through software. Otherwise this costly player is just a 30GB harddisk for me

Just wanted to mention - I bought the IR Remote thinking to make the player useful without navigation keys. Now I feel like I wasted more money instead of shifting to some other player by some other company with better customer service.

How to create password protected folder (with unlimited storage) on Mac?

I want to create password protected folder on my mac. I tried the method where you create a dmg file and mount it whenever you want to use the folder and unmount it when you don't. However, this method only lets me store, for example, 2 gb data. I cannot store beyong that level as an error message pops up saying... "the following files cannot be copied because there is not enough storage space in the dmg file"
How can I create a passpord protected folder which can store as much available space that is on my mac?
Is there an application that does that? Suggest me some names if someone already is using something like that.
Thanks much!

You need to choose the size of the image when you create it. If you are getting that message, you only set the image to hold 2GB of data.
If you choose a Sparse Disk Image or a Sparse Bundle Disk Image, you can set it to any size, however, it will only be able to store up to the space available on your Hard Disk. Physically, it will only be the size of the stuff you saved into it, but It doesn't shrink automatically when you remove things.
A Sparse Bundle differs from a Sparse Image in that it writes the contents to small files so that when Time Machine sees changes, it only backs up the small file change, not the 100 GB (or whatever) of the total image size.
Notice that having created a 10 TB disk image (as shown above), there is only 80 GB available on the mounted image as that is all the space I have available on the 500 GB drive.

How do I switch remote desktops with lion server screen sharing?

When I sometimes use the Lion Server screen sharing feature to take over my iMac using my Macbook, I find that I'm not able to switch desktops on the remote computer, i.e. using the three finger swipe.
Both are running the latest versions of Lion Server.
Now there MUST be some way to do that right?
Who knows?

Hi John, perhaps I did not express myself clearly.
My desktop iMac is set up with multiple desktops (desktop 1 for system stuff, desktop 2 for mail, messages, skype etc, desktop 3 for Safari and desktop 4 for text proessing, VM-Ware and other work).
When I work on that machine I'm logged in as one user and use the three finger swipe left and right or the Cmd-1 thru Cmd-4 keys to switch between those desktops.
I haven't founf how to do that from my a remotely connected MacBook Pro.
Both of which are running Mountain Lion in the mean time. The iMac runs Mountain Lion Server and the MBP has ML Server installed as well, but nut implemented. Just to be able to use the remote screen...
Hope this makes my question a bit mre clear...
Gerard

How to mount a remote folder with VPN

Similar Messages

Maybe you are looking for