How to open my NAT on my WRT150N router.

Hey, i'm not sure what to do about this and was wondering if i could get some help. I'm trying to open it so i can play an online game with my friends but as of now my NAT is "strict".
So thanks for any help !

Follow this link to open ports on your Router for MW2 to open NAT so you should be aable to play game with your friend.

Similar Messages

How to expand the signal of a WRT150N router

Hello,
In a recent trip to USA, I bought a WRT150N router and a WMP300N Wireless-N PCI Adapter, but due to the distance and walls I am not being able to receive the signal. I would like to know if Linksys has any kind of antenna or other product compatible with those two products that I can use to expand the signal and solve my problem.
Thanks and best regards,
Gustavo

well...the N-series router itself should give u a good range..however , if u want to go for a expand the signal , u can try out WRE54G v3...it works with WRT300N and WRT350N..so i guess it should work fine with WRT150N as well..

How to open a port for CCTV on Router Cisco DDR2201v1

Hello, I want to know how could I configure a Router Cisco DDR2201v1 for watching my CCTV System from anywhere with a internet connection. I already try to open a port in the NAT virtual server configuration but it didn't work. Could you help me please? Thanks
Can anybody tell me what's wrong with this configuration.

Hi.
Welcome to Cisco Home Community.
Please follow this link, https://supportforums.cisco.com/ for the correct product category.
Thanks.

How to do destination NAT in a 2600 router with IOS 12.3?

Hi All
I have a 2600 router with two LAN interfaces which I am using for a PoC and has the following settings:
FE 0/0 - 10.0.0.1/24 - client LAN - inside
FE 0/1 - 10.1.1.1/24 - server LAN - outside
The direction of the flows are from the clients to the servers. What I would like to achieve is when clients accessing the web server 10.1.1.10, this to be replaced by 10.1.1.100.
I have tried the above a few times but doesn't work. Is the above possible? And If so please provide me with a sample config.
Many Thanks
[email protected]

Yes, you can do this. You don't need destination NAT. Source NAT translations work both ways. This should work:
ip nat inside source static tcp 10.1.1.100 80 10.1.1.10 80
int fa 0/0
ip nat inside
int fa 0/1
ip nat outside
The bigger question is why you'd want to. Just because you CAN do something doesn't mean you SHOULD. Unless you have the 10.1.1.0 network subnetted or some sort of firewall/blocking in place, both IPs should be reachable by the hosts. Why not just have them go directly to 10.1.1.100 instead of going to 10.1.1.10? If there's a firewall or similar blocking 10.1.1.100, why not adjust your firewall settings instead? You could have a valid reason for doing this but I can't think of very many scenarios off the top of my head where this would make sense. If you can post more details on what you're trying to accomplish, you might get better advice on a better way to solve the problem.

How to change the NAT type to Open on a Imac using bridged connections

Hey everyone I have a problem. I play xbox live with my friends and i just moved and dont have a wireless adapter anymore. so i have bridged connections with my imac and xbox via ethernet. It works perfectly, but the only problem is that when i connect it say that my NAT type is strict. To play with all my friends i need a open NAT type. Does anyone know how to make the NAT type on the Imac open. And i do have a D-link router model DIR-625. When i called D-link they said to port forward, i did and it still didnt work, they said it must be the fire wall on the mac, microsoft said the same thing, that it might be the fire wall. I checked the fire wall and it said "All Incoming connections are allowed".
I would really much appreciate it if someone helped me. Thank you!

Yes, most likely. Microsoft has provided a list of XBox LIVE!-compatible routers. Since the OS X Internet Sharing feature is limited, there is no way to configure port mapping or placing the XBox in a DMZ with it. Typically, you either use a compatible router or configure port mapping/DMZ for non-compatible routers.

WRT120N How to open NAT type PS3 !!!!

Hi i have a WRT120N router.
it goes alrite in connection wise but for my ps3 my nat type is strict which wont let me join
in some of my mate's partie's or host a game. And i REALLY wanna fix it by opening my nat
i've bascially tried everything portforwading but when you save it when portforwarding, it doesn't save like it look's like on the
video's i have seen on youtube. Uhm iv'e done that DMZ thing which also didnt work.
iv'e bascially done everything on youtube and other site's
Im just wondering if it's just the router. Or just the way i have it all setup because my router is setup in
a different room with the computer which is hooked up with the modem and my ps3 is in my room which is a different room and is just connected threw WiFi my connection on the ps3 is wireless obviously. Should i buy a new router or just ring a linksey person ? .it's getting to that point.
And yeah i just wanna get it to open HELP PLEASE !!!!!
GriMxDRiFT3r.

Hi - I think you are wanting to connect your PS3 with an internet cable and go wired , rather than wireless. Going online means being connected to the internet which you have done already only your PS3 and you router have done this wirelessly.
You need to connect your router to your PS3 with a Cat 5 cable - standard ethernet cable, then look at your network settings on your PS3 - set these to a wired connection and choose the auto and default settings through the next pages and see how that works. It was really straighforward when I set mine up.
Hope this helps

How to open NAT for Linksys E1000 on PS3?

question in title:
it seems as though my gameplay on my ps3 has been very THICK(lag and delay on screen), I have tried changing the MTU and some other options and I already notice the difference but i think I can maximize my lag-free gaming if I completely open up NAT on my PS3.
Does anyone have a great guide that works?
Also would changing the MTU/ Disabling UPnP and unchecking anonymous internet requests effect my Download/Upload speeds or anything else, or does it just help fix gaming lag?
Input towards topic and questions i've mentioned will be greatly appreciated,
Thanks.
Greg

disabling the WMM has something to do with the support you get from the servers and from i was told that's not needed to be enbled it should be disabled, and by the way the linksys support team explained it's better disabled instead of enabled and it wouldn't hurt to get a actual gaming router .. i went with the E3000 and i ended up having to ship it back for some defective that i didnt even cause, i would look into a actual gaming router that supports gaming like the e3000 or the e3200 , it should said for gaming consles or something like that but i will totally look into your problem personally and go from there! intil then i would try to get in contact with playstation gaming system and figure out what ps3 ports are so you can go from there - there should be a way to test the nat type (there 3 nat type's on playstation 3 ) there's nat type 3, there is nat type 2 (which is open) and there is nat type 1 and the one we want is the nat type 2 i believe, which means open nat type (meaning plug and play enabled and open ports on the router )

Opening the NAT of Two Xboxes on WRT54G v8 Router

Hello everyone! I have two Xboxes and a WRT54G v8 router. Both Xboxes are connected to the WRT54G v8 router. How do I open the NAT of both Xboxes? Thank you!

Disable the UPnP.
The box said windows xp or better... So I installed Linux!

How to Change the NAT Type of an Apple Router

My dad just bought an apple Router and some new modem. now since i know the router is apple company i want someone to tell me how i change its NAT Type from Strict to either Moderate or Open because its preventing me from connecting to my friends on xbox live. Im also using a Macbook Pro for a computer so its apple software an their shouldnt be any reason this cant be resolved effectively i just need a guide to tell me how to go about fixing this problem.

Unfortunately, the AirPorts are not listed as Xbox Live-compatible routers ... so there is no guarantee doing this will get Open NAT status for Xbox Live!
The following web blog does a great job explaining the NAT issues with Xbox Live! Basically what it comes down to is that although you can get an Internet connection for the Xbox with the AirPorts, you may not get the necessary NAT setting (Moderate or Open) for the Xbox Live! on-line game that you want to play. As such, you basically have two options: 1) Create a DMZ (Apple calls this a Default Host) for the XBox or 2) Configure the AirPort for Port mapping to open the required ports to allow Xbox Live! access ... or 3) Use a compatible router.
Option 1 - Create a DMZ
AirPort Utility > Select the AEBSn > Manual Setup > Internet > NAT
Enable default host at: <Enter the IP Address for the XBox>
Option 2 - Configure Port Mapping
The following ports must be available for Xbox Live to operate correctly:
UDP 88
UDP 3074
TCP 3074
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the Xbox 360.
AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
Click the "+" (Add) button to enter DHCP Reservations.
Description: <enter the desired description of the host device>
Reserve address by: MAC Address
Click Continue.
MAC Address: <Enter the MAC hardware address of the Xbox or the MAC address of the wireless depending on how you connect the XBox to the network.>
IPv4 Address: <enter the desired Private IP address>
Click Done.
2. Setup Port Mapping on the AEBSn.
AirPort Utility > Select the AEBSn > Manual Setup > Internet > NAT > Configure Port Mappings
Click the "+" (Add) button
Service: <choose the appropriate service from the Service pop-up menu>
Public UDP Port(s): 88, 3074
Public TCP Port(s): 3074
Private IP Address: <enter the DHCP Reserved IP address for the Xbox you created earlier>
Private UDP Port(s): 88, 3074
Private TCP Port(s): 3074
Click "Continue"

How to open and closed posting period??

Dear Gurus,
Pls help me, how to open and closed posting period.when and how we used special period.
Regrds
Mahesh

HI,
Tcode is ob52
here we generally provide the following details
a/c type from a/c to a/c from period year to period year from period year to period
+ 1 2007 12 2007 13 2007 16
+ implies it applicable to all account types
generally we can have maximum 4 special periods and total no of periods(normal+special) should not exceed 16
generally we use special periods for year end adjustments like tax adjustments
if it is useful assign me points

Help, how to open and display blobs from tables

Dear all,
I am trying to store ms-word files on a table using a blob column.
Does anyone how to open the files and display them from a form using 9iAS?
Thank you.
Carlos.

And there may be, but you won't likely find that here. Do some time searching Google and maybe you'll find code that someone was nice enough to make freely available, although I wouldn't count on it. Were i a programmer and took the time to read those docs and write the code, I'd want to be paid for my time. But there are a lot of programmers who swear by freeware! You may get lucky.

How to open a specific file in projector.

Hi to all
can any body tells me that how to open a specific file in
projector with an application not in browser????
and also want to add a button to mute the sound just like in
intros with fade in and out effect.
its urgent....
Thanks in advance

Hi,
You can use FlashJester JStart
http://jstart.flashjester.com
that will open up any file the has been associated in Window
Explorer.
Download a FREE evaluation copy and try it for yourself.
Please look at the example files given.
Regards
FlashJester Support Team
e. - [email protected]
w. -
http://www.flashjester.com
There is a very fine line between "hobby" and
"mental illness."

Reporting Services - How to open a second table inside report, for each number of client (each apears in first table)

Reporting Services - How to open a second table inside report, for each number of client (each apears in first table)?
Exemple:
Table1
Cliente name:
John
Client number:
12345
Survay number of negative answers:
3
Table2
Questions and answers that were negative:
Question: How much time where you waiting
Avaluation: 3 (from 1 to 10)
Answer: They only called me 1 mouth later
Can you please help me?

Hi,
Based on the description, I understand that you want to add subreport in the main report. When previewing the main report, the subreport can be shown in detail. Please see the screenshots on my test:
In Reporting Services, we can create parameters and pass them from main report to subreport in order to control the data dynamically.
References:
Subreports (Report Builder and SSRS)
Add a Subreport and Parameters (Report Builder and SSRS)
If I have any misunderstanding, please feel free to contact me.
Regards,
Heidi Duan
Heidi Duan
TechNet Community Support

How to open new window and generate oracle report from apex

Hi,
I had created an application that generates PDF files using Oracle Reports, following this Guide.
http://www.oracle.com/technology/products/database/application_express/howtos/howto_integrate_oracle_reports.html
And I followed 'Advanced Technique', so that users can't generate PDF file by changing URL and parameters. This is done for security reasons.
But in this tutorial, when 'Go' button is pressed, the PDF file is displayed on the same window of apex application. If so, user might close the window by mistake. In order to avoid this, another window have to be opened.
So, I put this code in the BRANCH - URL Target. (Note that this is not in Optional URL Redirect in the button property, but the branch which is called by the button.)
javascript:popupURL('&REPORTS_URL.quotation&P2100_REP_JOB_ID.')
But if the button is pressed, I get this error.
ERR-1777: Page 2100 provided no page to branch to. Please report this error to your application administrator.
Restart Application
If I put the code 'javascritpt ....' in the Optional URL Redirect, another window opens successfully, but the Process to generate report job is not executed.
Does anyone know how to open new window from the Branch in this case?

G'day Shohei,
Try putting your javascript into your plsql process using the htp.p(); procedure.
For example, something along these lines should do it:
BEGIN
-- Your other process code goes here...
htp.p('<script type="javascript/text">');
htp.p('popupURL("&REPORTS_URL.quotation&P2100_REP_JOB_ID.")');
htp.p('</script>');
END;
What happens is the javascript is browser based whereas your plsql process is server based and so if you put the javascript into your button item Optional URL Redirect it is executed prior to getting to the page plsql process and therefore it will never execute the process. When you have it in your branch which normally follows the processes, control has been handed to the server and the javascript cannot be executed and so your page throws the error "Page 2100 provided no page to branch to"... By "seeding" the plsql process with the embedded javascript in the htp.p() procedure you can achieve the desired result. You could also have it as a separate process also as long as it is sequenced correctly to follow your other process.
HTH
Cheers,
Mike

How to open a new window from submit button &dialog page in current window?

We have a requirement, wherein we have a OAF search page for PO lines with search criteria, Go button to search ,result region (table layout) and a submit button(Create new expedite).
1. Now user can select some lines from result region and click on Submit button.
2. On click of submit button we need to pop up a window or may be a dialog page asking that " Do you want open supplier web link portal or not?".
3. If user clicks yes(in Dialog page) then first fetch the URL from a look up maintained in Oracle EBS on the basis of supplier of the lines selected and then open that URL in a new window and side by side we need to open a dialog page in search page asking "whether user has updated the expedite info in supplier portal or not?". On basis of this we need to updated some count in custom tables.
So in step 3 i am facing problem, that how to open an URL in a new window through a submit button and side by side want to open a dialog page in the current window also.
Hope a quick response from you all.
Note:- To open a custom page we can have a link or button(button of type button and not submit button) on base page with destination url property as following javascript:
javascript:var a = window.open('OA.jsp?page=/XXX/oracle/apps/xxx/......&retainAM=Y', 'a','height=500,width=900,status=yes,toolbar=no,menubar=no,location=no'); a.focus();
So the question is how to do the same for submit button on OAF page???

Antriksh,
You just need to attach a submit action in button bean and not submit button bean, based on the output of confirm type of alert in javascript.
Here is code u need to put in destination url of the button:
//replace <confirm message> by message you want to show.
javascript:input=confirm('<confirm message>');if(input==true){submitForm('DefaultFormName',0,{XXX:' abc'});}" Now in the process request of the base page CO, u can get parametre 'XXX' from the pagecontext....so
if((("abc").equals(pageContext.getParameter("XXX"))))
{/// custom LOGIC }
The same i have replied in your mail. I hope this resolves the issue.
--Mukul

How to open my NAT on my WRT150N router.

Similar Messages

Maybe you are looking for