How to open ports 2078 and 2077

I can't seem to figure out how to do this.
I need it for a webdisk for my site but can't get these 2 porst to open so it can connect.
any help on how/where I go to do this?

I'm not entirely sure if you're using the Mac OS X Server or the Mac OS X client software version here, so the following covers both. Use of System Preferences implies client, though this is a server forum.
With Mac OS X Server 10.6, use the Server Admin tool to open up the ports you need. Launch Server Admin > select the target server > select Firewall > select Settings > select Services, open the ports, Save, etc.
With Mac OS X client 10.5.1 and later and with 10.6 and later, the firewall mechanisms and settings are application-based and not port-based, and you select the application to allow, and it can then use whatever ports it needs. System Preferences > Sharing > Advanced... and then the + to add the application. (Details: [ht1810|http://support.apple.com/kb/ht1810])
If you're running this box as a network gateway, then things can get a little more complex; I'd tend to use an external firewall if that's an option.
If you're running this as the client for the disk services (as I might guess) and if you're accessing a remote web disk on a remote system via ports 2077 (SSL) and 2078, then I wouldn't usually expect to need to open these ports on the client; it's usually the remote server system and not the client that needs to open ports. (Are you getting any diagnostic messages here? Are you looking to serve disks out to other hosts via this protocol? If so, and if you're on Mac OS X Client here, then try adding the application that serves the disks to the list of applications known to the firewall.)
As an alternative, Apple servers and servers from other providers can run WebDAV disk services via port 80, which means that most any server that allows http web connections can also allow WebDAV connections. (WebDAV is a built-in feature of this Apache web server, so most any Apple Mac OS X box can serve disk space using http port 80 and WebDAV.)
The lower level approach to opening the ports is the ipfw tool, and the command line.

Similar Messages

Total Newbee, How to open ports 5198 and 5199 for Amateur Radio software program

I am a Amateur Radio operator using a software program called Echo Link which will enable me to talk to other radio operators around the would through repeaters running this software. I need to open ports 5198 and 5199 in my Airport Time Capsule for this software to work. How do I open these ports? They talk about mapping the ports which I don't understand. Below is a screen shot of an older version of Airport that shows what I want to do.
I tried to do it but it does not work and I can't change the private IP Address. Here is a screen shot of what I tried to do below. Thanks for any help you can provide.

It says above 2 relevant and 1 correct answere available .............
I'm new here so could anyone direct me to these answeres?

How to open ports 80 and 443

How do you open ports 80 and 443? I'm trying to connect a tv to the internet.

What router are you using? Who is your ISP? Also, what exactly are you trying to accomplish?

How to open ports 119 and 443 in my Mac?

I've been trying to use the UseNeXT software with my Mac with no success. I called their support and they told me I need to open the ports 119 and 443. I contact Apple support and they told me that is beyond their scope (???).
Can somebody help me with that? I tried to find it online, but all tutorials that i tried didn't work or are outdated.
Thanks

Hi Drew,
It probably depends on the router as to the method used to open the ports.
As I have said elsewhere in the thread the first 1024 ports are open in most router to allow things to work Out of the Box such as Mail (110, 25, 567, 569, 995, 996 and many more ) and web Browsing (port 80 mostly but secure site can use 443) FTP (21 and 22) to name some.
Port Forwarding is one way to open some of the ports for One IP (computer).
Most routers have table for doing this and this can be limited as to the number of ports included.
This Linksys pic shows how to do it for some as it allows groups based on Start and end ports. However it restricts it to one IP
DMZ is a form of Extreme Port Forwarding that opens all 65535 ports to one IP (Computer)
In both the above cases other computers (IP addresses) are excluded from using the ports.
Port Triggering doe allow multiple computers to access the same Port but requires that you know the lead - Trigger - port involved for each app.
It is limited by the table size for your particular router.
Same Router in Trigger ports for iChat 3
Most router come with UPnP nowadays.
It is an ON/Off setting that allows the apps on the computer to say which ports are needed and when.
On some you can reduce the time to live and the Hop amounts.
The ports stay open from a period of normally 30 mins after non use.
This can be changed.
It also tends to list the number of Hops (the number of devices beyond the UPnP device) that it can be heard.
My Sky Hub
I have no other router on my network but I do sometimes use Internet Sharing between two computers hence the 2 Hops.
Every other device is only one Hop away from the the router.
There are concerns that the "Advertisement" is seen upstream (internet side) as well as device downstream.
The Concern is that this could be Up to your ISP and then down to the "next" IP end user on the particular router/server at the ISP end.
I have seen no evidence of this being the case.
Hope this helps.
8:45 pm Monday; May 5, 2014
 iMac 2.5Ghz i5 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

How To Open Ports 80 And 443 In Vista.

Hi Guys Yeah I'm Trying To See That Mine's Ports Are Working Correctly Or Not Help If Any One Knows That Ports Would Might Help To Restore Your I Device May Be I Haven't Configured Mine's Pc Correctly A Lil Bit Yet So Help Me To Configure Mine's Pc Settings That Would Restore And Update Mine's I Device Using Original FW.
Thanks

What router are you using? Who is your ISP? Also, what exactly are you trying to accomplish?

Don't know how to open ports

Hello.
Could someone please tell me how to open ports on my LinkSys WRV200 Wireless-G VPN Router.
Thank you.

Open up internet explorer. On the address bar type the numbers 192.168.1.1 (username is admin, password is admin as well). Go to the Firewall tab. Depending on what kind of port opening you want, you either click on the Port Triggering or Port Forwarding subtab.
If you are hosting a certain program or application, use port forwarding. If you are just simply trying to use and access it, use port triggering.

How to open a page and closing source page in jdev 10.1.3.3

how to open a page and closing source page in jdev 10.1.3.3.
for example.
From page 'A' , we are opening a page 'B' and closing the page 'A'. how this can achived.Please let me know

Your question is totally not clear?
What page? a JSF page? A code editor in JDeveloper?

How to open .rar files and .exe files on mac

HI
I'm new user on mac and would like to know how to open .rar files and .exe files on MAC OS X
Thanks

How is this a Compressor question?
.exe is a Windows only Executable, and can't be opened on a Mac, unless you have Windows installed.
Michael Trauffer

How to open Port 85 & 37777 for NVR

I recently purchased a security camera system (Q-SEE / QC Series) for my house but the system required to have open ports 85 and 37777 to be able to view the cameras from outside the local network ie: from my computer at work.
Can someone please help me? I'm not a computer savy and I'm having a hard time to be able to accomplish this task.
Thank you in advance

Matt's pointed you in the right direction - ignore the stuff about uPNP, you just need to use AirPort Admin to configure your time capsule - setup port forwarding to forward ports 85 and 37777 to the IP address of your camera.
Use AirPort Utility to access your Time Capsule. Under the Network tab you have the configuration for the network, including port forwarding options:
Click the + button to add a port forwaring rule and add the first public port (e.g. 85) and the IP address of the camera on the LAN that it should be forwarded to:
Here I've created a rule for port 85 - I'm assuming it's using TCP, but if it's using UDP just add the port values into the UDP fields instead (or in addition to). Also set the IP address to your camera's address (which probably isn't 10.0.1.201 as above).
Rinse and repeat for port 37777

How to open port 8000 (outward)

Can someone please explain how to open port 8000 for streaming Nicecast to my (network) IceCast2 server? Thanks!

If all you are using is the inbuilt firewall then it shouldn't be blocking outward connections.

How can I set up a WD My Cloud with my Airport Extreme - I can't get it to open ports 80 and 443?

For remote internet access to the WD My Cloud Mirror, I have been advised that ports 80 and 443 must be open in order to reach the WDMyCloudMirror. My Motorola Gateway (Surfboard SB6141) is connected directly to my Airport Extreme (WAN port) which is in turn connected to the WDMyCloudMirror (all by ethernet cables). I do not have FULL instructions on how to properly manually configure the Airport Extreme to open the ports. I have tried an earlier posting which provides many of the steps, but not all of the required information is included (how to determinge the IP address to be assigned, etc.). I did the best I could with the information given, but the test using "YouGetSignal" showed the ports as still closed and attemps to reach the WDMyCloudMirror by the internet failed as well (of course). The WDMyCloudMirror has enough Apple "stuff" included in it (software, I suspect) that an Apple legal acceptance is required for its set-up, yet Western Digital Tecnical Support is unable (or unwilling?) to help with this aspect of its configuration required to work within the Airport Extreme environment. I have returned the WD My Cloud Mirror to Amazon as "not able to work", but I have not given up the hope that I can eventually get the ports open so that I can get this cloud device, or one similar, to permit remote internet access.

Port Forwarding.....or Port Mapping....as Apple calls it is a difficult and complex configuration method for most users. Because there are so many variables involved in this type of setup, it is not possible to provide a step by step guide that will work for everyone with all devices.
It is possible that a setup guide exists for the the WD drive and AirPort Extreme, but you will have to go looking for it on the Internet. Even if you find one, it may not be tailored to your specific situation or needs.
Sometimes, you can do everything right....at least according to someone's article or "how to" guide, and things still will not work correctly.
In situations like this, when you really don't know what to do, you need to enlist the aid of an IT pro, who will know what to do based on your particular products and unique circumstances. Sometimes....they won't be able to get things working either due to particular circumstances.
But, before you do this, I would strongly recommend that you use a Static IP address for your Internet connection with your ISP. If you do not have this now, contact them to ask them if they offer this type of connection. Expect to pay more for this type of service, of course.

Firewall in 10.5, how to open ports and how to manage?

I am pulling my hair out with the new firewall in 10.5. In 10.4 I could just set ports as I liked in the control panel, in 10.5 there is no such thing.
I need to for example open port 49999 to allow PageSender to function in my network.
I need to open port 5901 to work with JollyFast VNC, as port 5900 is used by Apple Remote Desktop and the conflict if they both use the same port.
Some of these ports I need permanent open like 59999 and others for one session and than close again, like 5901. Again in 10.4 I made the rule in the pref pane, ticked the box and Bob was your uncle. Now?
I would like to be able to see what ports are open and active on the machine. I have no idea as to where I could see this.
And at the same time I would like to keep the firewall as closed as possible as I am often on line in hotels etc.
So I need help, is there a manual somewhere someone is aware of? Or do you have any answers?

The new Application Firewall does not work in the same way as IPFW (the main firewall in 10.4).
Instead of managing ports, it simply controls the access of applications to any port. Thus, if you want PageSender to receive connections, you simply need to switch the firewall to "Set access for specific services and applications", and then add PageSender to the list, with "Allow incoming connections". When you do this, PageSender will be able to receive connections on any port that it needs to.
If you don't like this method of controlling connections, you can still use IPFW. Apple has removed the GUI, but you can download a GUI application like [NoobProof|http://www.hanynet.com/noobproof> or [WaterRoof|http://www.hanynet.com/waterroof/index.html], and you can then set access for specific ports.
There are no problems with using both IPFW and Application Firewall.
Cheers,
Rodney

SRP527W - How to open port 491 for Go-Global apps

Hi Guys,
Recently bought a Go-Global to a remote which require to open port tcp 491. I'm using SRP527W, how configure using this devices, I tried using the port forwarding but failed. Need anyone can help thanks.

I have the same request, and have tried the steps written in the post online, but the screen options are not what was explained.
Per the instructions with my IP Camera support, here's what I need to do:
======
First thing you will need to do is make sure that in the network settings of your camera that you have entered the correct gateway and DNS information. The default gateway address is going to be the LAN IP address of your router. The primary DNS address is also going to be the LAN ip address of your router. For the secondary DNS address enter the address 4.2.2.2, save these settings in your camera.
The second thing you will need to do is, you will need to log into your router and forward the port your camera is using (the default port is port 80) to the LAN IP address of your camera. This will be done in the port forwarding section of your router. You may need to contact the manufacturer of your router to have them walk you through these steps.
In order to access your camera, you will need to use the WAN (public) IP address that was provided to you by your ISP. As an example, the URL will look like this, HTTP://65.44.139.2 or if you are using a different port number other than 80, you will have to use the URL with the port number. That URL would look exactly like this, HTTP://65.44.139.2:81
======
I've changed the secondary DNS to 4.2.2.2, but I cannot find how to forward the camers's port to the IP address of the camera....I've set 198.268.1.240 as the camera address.
Can you help?
Thanks,
Kent Tunell

How to open new window and generate oracle report from apex

Hi,
I had created an application that generates PDF files using Oracle Reports, following this Guide.
http://www.oracle.com/technology/products/database/application_express/howtos/howto_integrate_oracle_reports.html
And I followed 'Advanced Technique', so that users can't generate PDF file by changing URL and parameters. This is done for security reasons.
But in this tutorial, when 'Go' button is pressed, the PDF file is displayed on the same window of apex application. If so, user might close the window by mistake. In order to avoid this, another window have to be opened.
So, I put this code in the BRANCH - URL Target. (Note that this is not in Optional URL Redirect in the button property, but the branch which is called by the button.)
javascript:popupURL('&REPORTS_URL.quotation&P2100_REP_JOB_ID.')
But if the button is pressed, I get this error.
ERR-1777: Page 2100 provided no page to branch to. Please report this error to your application administrator.
Restart Application
If I put the code 'javascritpt ....' in the Optional URL Redirect, another window opens successfully, but the Process to generate report job is not executed.
Does anyone know how to open new window from the Branch in this case?

G'day Shohei,
Try putting your javascript into your plsql process using the htp.p(); procedure.
For example, something along these lines should do it:
BEGIN
-- Your other process code goes here...
htp.p('<script type="javascript/text">');
htp.p('popupURL("&REPORTS_URL.quotation&P2100_REP_JOB_ID.")');
htp.p('</script>');
END;
What happens is the javascript is browser based whereas your plsql process is server based and so if you put the javascript into your button item Optional URL Redirect it is executed prior to getting to the page plsql process and therefore it will never execute the process. When you have it in your branch which normally follows the processes, control has been handed to the server and the javascript cannot be executed and so your page throws the error "Page 2100 provided no page to branch to"... By "seeding" the plsql process with the embedded javascript in the htp.p() procedure you can achieve the desired result. You could also have it as a separate process also as long as it is sequenced correctly to follow your other process.
HTH
Cheers,
Mike

How to open an URL and close the URL window, using adobe javascript

Hi,
Is it possible to open an URL and close the URL back again(without allowing the user to perform any other operation)? I was able to acheive the opening of the URL, using the app.launchURL("address". true); - But here it lauches in new window, and how do i close the window using the javascript. Is it possible?
Thanks.

Hi all
In addition to what Bobby W - Adobe TS added, you might find
the following useful as a bypass or workaround to the pesky prompt.
var pw=window.parent;pw.opener=window.self;window.open("
http://www.adobe.com");
pw.close();
I think this will only work for IE browsers. Actually, I
think the whole window.close() only works for IE, but could be
wrong about that.
Cheers... Rick

How to open ports 2078 and 2077

Similar Messages

Maybe you are looking for