How to reboot cluster or Tftp Server

Dears
Can you guide me how to reboot cluster and tftp server

Hi Obaid,
Please find the replies:
I have upgrade the cucm 8.5 and I uploaded the device pack, now I need to restart the tftp server.
so for this what will be the case?
1. Whether phones will restart? yes
2. Will they take new firmware yes
3. If I want old to still remain on running phones and new phones should take new firmware? u need to copy the new firmware in Phone Load Name.
http://www.cisco.com/en/US/products/hw/phones/ps379/products_tech_note09186a0080a277a3.shtml
regds,
aman

Similar Messages

Cisco Prime TFTP Server Question

Our organization recently installed Cisco Prime 1.3 on a Linux box. I am used to using the older WCS which also had a built in TFTP server. The old WCS was installed on a Windows Box and thus I was able to navigate to the TFTP server using Windows Explorer and the UNC path. However, I cannot seem to access the TFTP server on the new Prime 1.3 server via that method. I have verified that the TFTP and FTP servers are both enabled in Prime server settings and I have also verified that I can access the FTP port via a PC on the network and that the WLCs on the network are sucessfully backing up to the Prime TFTP server each night.
How can I access the TFTP server to retrieve these WLC backups if needed?

you need to enable root access. then you can scp the files out of the directory easily enough.
from cli
root_enable
follow prompts
root
psswd - set password
should be abel to ssh as root at that point, if you can want to say it's /localdisk/tftp, or just ls /localdisk
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Have a dedicated TFTP Server for CCM cluster

Hi,
One CCM3.3(3) cluster in production, in which the publisher server was the TFPT server.
Now we need expend the system and would like to deploy a dedicated TFTP Server for the cluster. Is there anyone telling me what I should concern if I have a dedicated TFTP server other than the publisher server?
Thanks,
JJ

Hi,
I have a similar issue. I have actually a pub and a sub, the pub is also the tftp server. Following the SRND, I need a dedicated tftp server because we're almost at 1250 users, growing every day. My question, which may seem very basic, is how do I build a dedicated tftp server ?

How to Setup Windows TFTP Server in Windows 2008 R2

Hi,
Can anyone please let me know, how to install TFTP Server in Windows 2008 R2.
I installed Windows Deployment Service to get TFTP (got this info in some forum), but I did not see TFTP Service in the Service Manager.
I am a newbie so plz let me know the steps in details.
Thanks in advance.

James, WDS ships with a TFTP server as part of the suite of services that are required to boot from the network. The information you've posted above is not correct.
Hi Aaron,
Thanks for your clarification. Towards the WDS TFTP Server, we could find the following statement below:
You use the Windows Deployment Services Trivial File Transfer Protocol (TFTP) server to download the files that are needed to do a network boot using the Pre-Boot Execution Environment (PXE).
From:
WDS TFTP Server
I understand that the we could select Deployment Server and Transport Server during the WDS setup processing. However, neoraghav would like to install TFTP server from the Server Manger towards the Windows Server 2008 R2. I noticed the statement as followed:
The TFTP client is optional software, and marked as deprecated on Windows Vista® and later versions of the Windows operating system. A TFTP server is no longer provided by Microsoft for similar security issues.
From:
Trivial File Transfer Protocol (TFTP) Overview
I should make my reply as clear as possible. Sorry for confusion. :-(
Regards,
James
James Xiong
TechNet Community Support

How to configure logs to be sent for TFTP server !?

hi
I want to let the router or the switch to sends the log to TFTP server, how can I do that !?
including things like debug commands results
thanks,

You want to send the logs to the Syslog server..right? Use the logging command to do it.
logging x.x.x.x is the command.
Use the logging trap command to set the level of logging.
Router(config)#logging trap ?
<0-7> Logging severity level
alerts Immediate action needed (severity=1)
critical Critical conditions (severity=2)
debugging Debugging messages (severity=7)
emergencies System is unusable (severity=0)
errors Error conditions (severity=3)
informational Informational messages (severity=6)
notifications Normal but significant conditions (severity=5)
warnings Warning conditions (severity=4)
<cr>
CF

Replacing a TFTP server in a cluster

Replacing a TFTP server in a cluster and with everything else being the same minus the MAC address on the NIC, are there any issues I could possibly run into here?
Thank you for the help the server is an MCS7845H2.

No issues, MAC address is irrelevant on TFTP as it only matters on the Pub, simply install CUCM on the new server assigning the same IP and hostname and then restore from backup.

FAQ: How are notifications made when a server is added to a cluster?

Hello,
          From the FAQ:
          Q: How are notifications made when a server is added to a cluster?
          A: The WebLogic Server cluster broadcasts the availability of a new
          server instance each time a new instance joins the cluster.
          Cluster-aware stubs also periodically update their list of available
          server instances.
          Does anybody know which interval is used for those Cluster-aware stubs?
          Regards,
          Merg


that's incorrect. It is not periodic. Anytime the server comes up it uses
          multicast to advertise its availability as well as the services it
          provides. When all the announcements are through you can get Cluster-aware
          stubs from that server as well.
          Cheers,
          -- Prasad
          Merg wrote:
          > Hello,
          >
          > From the FAQ:
          >
          > ----------
          > Q: How are notifications made when a server is added to a cluster?
          > A: The WebLogic Server cluster broadcasts the availability of a new
          > server instance each time a new instance joins the cluster.
          > Cluster-aware stubs also periodically update their list of available
          > server instances.
          >
          > ----------
          > Does anybody know which interval is used for those Cluster-aware stubs?
          >
          > Regards,
          > Merg
          Cheers
          - Prasad

How to make CUCM as a TFTP server , then copy files to Voice Gateway ?

how to make CUCM as a TFTP server , then copy files to Voice Gateway ? anyone knows?

Hi,
Please check the following link
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/6_1_1/ccmsys/cucm-accm-611/a02tftp.html#wp1023004
Understanding How Devices Access the TFTP Server
You can enable the IP phones and gateways to discover the TFTP server IP address in one or more of the following ways, depending on the device type:
•Gateways and phones can use DHCP custom option 150.
Cisco recommends this method. With this method, you configure the TFTP server IP address as the option value.
•Gateways and phones can use DHCP option 066.
You may configure either the host name or IP address of the TFTP server as the option value.
•Gateways and phones can query CiscoCM1.
Ensure the Domain Name System (DNS) can resolve this name to the IP address of the TFTP server. Cisco does not recommend this option because it does not scale.
•You can configure phones with the IP address of the TFTP server. If DHCP is enabled on the phone, you can still configure an alternate TFTP server IP address locally on the phone that will override the TFTP address that was obtained through DHCP.
•Gateways and phones also accept the DHCP Optional Server Name (sname) parameter.
•The phone or gateway can use the value of Next-Server in the boot processes (siaddr).
Devices save the TFTP server address in nonvolatile memory. If one of the preceding methods was available at least once, but is not currently available, the device uses the address that is saved in memory.
You can configure the TFTP service on the first node or a subsequent node, but usually you should configure it on the first node. For small systems, the TFTP server can coexist with a Cisco Unified Communications Manager on the same server.
HTH
Manish

How to transfer image software from pix to tftp server

Hi,
I have a pix 515 E vers. 6.3(3). How can I back up thr current image to a tftp server?
Tanks in advance

There is no way how copy the OS from the PIX to a tftp server
You can only copy from tftp to flash (copy tftp flash)
Its security (licencing) feature not to allow the OS to be copied from PIX
You can only copy current configuration with command wri net
M.
Hope that helps rate if it does

How do you cluster Maverics server?

How do you cluster Maverics server? I have two Mac Minis running Mavericks server that I would like to cluster (mirror) together preferably as load balanced but failover would be the next best thing. I am not actually using the services of server, but am hosting a streaming application.
Any ideas?

In terms of general Mac server 'clustering' Apple used to provide capabilities to do this but sadly killed off all their options in this area some time ago.
In your case even if Apple still provided those capabilities they would not apply as any streaming application would need to have been written to provide its own clustering capabilities.
The nearest option you can get to realisitically with Mac servers is to use DNS load-balancing where a load-balancer will 'share' the load between two or more servers and also test a server is live before sending a request to it. The servers need to have some method of having the same data which might mean using a SAN to store the data and Macs can access a SAN as MrHoffman mentioned. However none of Apple's own server services would really benefit from this.
A hypothetical example that could be achieved would be to have two Mac servers running Apple Software Update Server, you would not and cannot point client Macs to both but you could point client Macs to a DNS load-balancer which would allocate requests to one of the Mac servers. In this case the two Mac SUS servers might indepenently download updates or you might use the same 'folder' on a SAN or you might run some other sync command between the two. In my own case I actually setup two SUS servers in VMware virtual machines using Linux and had them each store their own copies but sync their folders, I had one run at 12am and one at 12pm so updates got downloaded twice a day. The DNS load-balancer then forwarded requests to either of them. (I used Reposado to act as the SUS software.)

How to to make Cluster between two server 2012 Datacenter with share storage and Hyper-V role then install Exchange 2013 on each server datacenter then make DAG between Exchange servers

Dears,
I have IBM Flex server with built in storage,
HOW to to make Cluster between two server 2012 Datacenter with share storage and Hyper-V role then install Exchange 2013 on each server datacenter then make DAG between Exchange servers?
If there any prerequisites of the Share storage types ?and any configuration guide to deploy Cluster between two Server 2012 datacenter ?

Microsoft Failover Clusters require shared storage. If you wish to create a failover cluster with local storage, you need to use third party software to mirror the disks and present it to the hosts (siog.com, datacore.com, starwind.com). If you
use third party software, you will need to follow their instructions for configuring the environment.
Questions on how to configure Exchange environments are better asked in an Exchange forum.
.:|:.:|:. tim

How to load an IOS from CD to a tftp server?

Hi,
Hw do you copy an IOS from a CD to a tftp server? Cisco TFTP and Solar Winds 2003 Standard Edition TFTP servers are installed on a PC running Win XP.
Thanks.

Thanks for your advise. What is the procedure for mapping the directory in the tftp services?
Thanks.
Said
The following are error messages from cnsole.
Router#copy flash tftp
Source filename []? c2600-is-mz.121-4.bin
Address or name of remote host []? 172.16.40.2
Destination filename [c2600-is-mz.121-4.bin]?
%Error opening tftp://172.16.40.2/c2600-is-mz.121-4.bin (Undefined error)
Router#copy tftp flash
Address or name of remote host []? 172.16.40.2
Source filename []? c2600-io3-mz.123-9.bin
Destination filename [c2600-io3-mz.123-9.bin]?
Accessing tftp://172.16.40.2/c2600-io3-mz.123-9.bin...
%Error opening tftp://172.16.40.2/c2600-io3-mz.123-9.bin (Timed out)
Router#

How do I correctly configure TFTP?

Hi again!
Now that I'm talking to my serial device, I need to provide it with a TFTP server (on an Ethernet) from which it can install its firmware. OS X, being UNIX, should be perfectly capable of running such a server. So, I looked around, found the xinetd and xinetd.conf man pages, set 'enable = yes' in /private/etc/xinetd.d/tftp, verified that /usr/libexec/tftpd exists, put the files to be served in /private/tftpboot, poked a hole in my firewall for port 69, and rebooted.
No joy. Using the Console utility to view the system.log, I do see xinetd starting tftpd in response to requests from my device's IP-address -- so it appears that the requests are getting through the firewall and are recognized by xinetd, and it is starting tftpd. However, the client on the device is claiming that the connection is timing out (in its cryptic way -- it is saying ' T'), and it is retrying every 5 seconds.
I can't see a way to get any more detailed information from tftpd about the problem. Has anyone successfully set up the stock OS X xinetd/tftpd ? Is there some step I'm obviously missing? Does anyone know how to get details of errors tftpd encounters?
Thanks!

Obviously my dump is showing 7 packets capt, 7 rec by filt, 0 pkts dropped by kernel. But we knew it was working. Just a cross check. On system pref pane, I did new, with port 69, tftp with check on. Now when I did this last night and this am(it wouldn't stay after sleep) I originally typed on the new(under firewall) tftpd because without the d it wouldn't let me ok it. So I did with d, ok'd it, and it now, and last night shows 2 entries of port 69(one w/tftpd & one w/tftp). I don't know why it took that way, but it does and works. And my xinetd is like your directions. My bs.txt in /private/tftpboot are 400(rrr) owned by me, and /private/tftpboot is root w/rwxr-xr-x. And(forget the structure of disable = no, for it still works and isn't worth the change).
service tftp
cps = 200 5
disable = no
socket_type = dgram
wait = yes
user = nobody
server = /usr/libexec/tftpd
server_args = /private/tftpboot
groups = yes
flags = REUSE
}

TS3899 I can't SEND email from Telus account in Alberta, Canada? Does anyone know how to set up the Outgoing server? Help! And thanks!

Can't SEND email from Telus account in Alberta, Canada, unless I go to web mail. Does anyone know how to set up the Outgoing server? Incoming is fine. Outgoing used to work. We changed it when we went to another location, and can't get it back. Telus support can't fix it. Neither smtp.telus.net NOR mail.telus.net works for Outgoing server to send mail. Please help! Thanks.

iOS: Unable to send or receive email
http://support.apple.com/kb/TS3899
Can’t Send Emails on iPad – Troubleshooting Steps
http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
Setting up and troubleshooting Mail
http://www.apple.com/support/ipad/assistant/mail/
Server does not allow relaying email error, fix
http://appletoolbox.com/2012/01/server-does-not-allow-relaying-email-error-fix/
Why Does My iPad Say "Cannot Connect to Server"?
http://www.ehow.co.uk/info_8693415_ipad-say-cannot-connect-server.html
iOS: 'Mailbox Locked', account is in use on another device, or prompt to re-enter POP3 password
http://support.apple.com/kb/ts2621
iPad Mail
http://www.apple.com/support/ipad/mail/
Try this first - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
Or this - Delete the account in Mail and then set it up again. Settings->Mail, Contacts, Calendars -> Accounts Tap on the Account, then on the red button that says Remove Account.
 Cheers, Tom

Connecting managed server to cluster's administration server

Hello,
I have a problem when trying to connect managed server to cluster's
administration server.
When starting the managed server I get a security exception:
[javax.naming.AuthenticationException [Root exception is
java.lang.SecurityException: Administrators must log in over admin port with
admin protocol.]]
weblogic.management.configuration.ConfigurationException: admin URL:
t3://192.168.14.15:7001 - with nested exception:
[javax.naming.AuthenticationException [Root exception is
java.lang.SecurityException: Administrators must log in over admin port with
admin protocol.]]
at
weblogic.management.Admin.initializeRemoteAdminHome(Admin.java:893)
at weblogic.management.Admin.start(Admin.java:303)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:331)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:169)
at weblogic.Server.main(Server.java:35)
I get the same result when testing the connection setup with
java weblogic.Admin -url 192.168.14.15:7001 -username system -password xyz
CONNECT 1
Background for this problem:
I'm trying to evaluate WLS6.0 clustering for my RMI services. I have two
machines setup with my test domain (DEdomain) and one cluster (DECluster)
within it.
In administration server (machine A) I defined two servers to be run in
machine A and machine B:
DEserver2 in machine B (to be started as managed server) and DEserver3
in machine A
I'm going to bind a same service into these above servers of my DECluster.
In machine B's startManagedWeblogic.sh I have:
java -ms64m -mx64m -classpath
$CLASSPATH -Dweblogic.Domain=DEdomain -Dweblogic.Name=$SERVER_NAME -Dweblogi
c.management.server=$ADMIN_URL -Djava.security.policy==$WL_HOME/lib/weblogic
.policy -Dweblogic.management.username=system -Dweblogic.management.password
=$WLS_PW weblogic.Server
In machine A I have administration server DEserver1 listening port 7001.
And for the domain and cluster building I followed all relevant e-docs
manual pages. It's still somewhat blurry what kind of preparations I have to
make in managed server side to join the domain; for example do I have to
have identical domain directory structure within machine B and do I have to
configure something with admin console or is everything handled by
connecting to the administation server and reading the domain's config.xml
from machine A.
I'm sure I have missed some fundamental idea for building clustered services
and would greatly appreciate if someone had any good tips or ideas.
Best regards,
Harri

Hi Kumar,
and thank you. That fixed my problem
Best regards,
Harri
"Kumar Allamraju" <[email protected]> wrote in message
news:[email protected]...
It appears you had set the administration port & listen port on the admin
server.
Logging onto admin server via admin port is broken currently. I wouldsuggest
you to set only listen port
and see how that goes.
Kumar
"Harri Töhönen" wrote:
Hello,
I have a problem when trying to connect managed server to cluster's
administration server.
When starting the managed server I get a security exception:
[javax.naming.AuthenticationException [Root exception is
java.lang.SecurityException: Administrators must log in over admin portwith> > admin protocol.]
weblogic.management.configuration.ConfigurationException: admin URL:
t3://192.168.14.15:7001 - with nested exception:
[javax.naming.AuthenticationException [Root exception is
java.lang.SecurityException: Administrators must log in over admin portwith> > admin protocol.]
at
weblogic.management.Admin.initializeRemoteAdminHome(Admin.java:893)
at weblogic.management.Admin.start(Admin.java:303)
at weblogic.t3.srvr.T3Srvr.initialize(T3Srvr.java:331)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:169)
at weblogic.Server.main(Server.java:35)
I get the same result when testing the connection setup with
java weblogic.Admin -url 192.168.14.15:7001 -username system -password
xyz
CONNECT 1
Background for this problem:
I'm trying to evaluate WLS6.0 clustering for my RMI services. I have two
machines setup with my test domain (DEdomain) and one cluster(DECluster)
within it.
In administration server (machine A) I defined two servers to be run in
machine A and machine B:
DEserver2 in machine B (to be started as managed server) andDEserver3
in machine A
I'm going to bind a same service into these above servers of myDECluster.
>>
In machine B's startManagedWeblogic.sh I have:
java -ms64m -mx64m -classpath
$CLASSPATH -Dweblogic.Domain=DEdomain -Dweblogic.Name=$SERVER_NAME -Dweblogi
>>
c.management.server=$ADMIN_URL -Djava.security.policy==$WL_HOME/lib/weblogic
>>
.policy -Dweblogic.management.username=system -Dweblogic.management.password
=$WLS_PW weblogic.Server
In machine A I have administration server DEserver1 listening port 7001.
And for the domain and cluster building I followed all relevant e-docs
manual pages. It's still somewhat blurry what kind of preparations Ihave to
make in managed server side to join the domain; for example do I have to
have identical domain directory structure within machine B and do I haveto
configure something with admin console or is everything handled by
connecting to the administation server and reading the domain'sconfig.xml
from machine A.
I'm sure I have missed some fundamental idea for building clusteredservices
and would greatly appreciate if someone had any good tips or ideas.
Best regards,
Harri

How to reboot cluster or Tftp Server

Similar Messages

Maybe you are looking for