How to reconfigure my Linksys EA2700 wi fi router

I made the mistake of resetting my router (EA2700) when it was down and now I need to reconfigure it.  Can anyone help me or do I need to pay tech support at Linksys?
Thanks

I recommend that you phone contact your regional Linksys support office and ask for help and information...

Similar Messages

  • How to bridge a linksys cisco E1200 series router?

    I have recently purchased a linksys cisco E1200 series router and would like to know how to bridge the connection to my xbox

    purchase 881w, get rid of linksys. That should do it.
    Sent from Cisco Technical Support iPad App

  • Problem with linksys EA2700

    I've got a problem with my linksys ea2700. one time my network components get an ip-address like 192.168.x.x, the other time they get an ipaddres 10.184.x..x, I want that all my components will get the 10.184.x.x address, how can I solve this problem?

    If your modem has a capability to be a DHCP server then just configure your EA2700 router as bridged. In that way, the EA2700 router will just act as a pass through device.
     Setting up your Linksys Wi-Fi or Smart Wi-Fi Router to Bridge Mode

  • No Internet access without replugging WAN to Linksys EA2700

    Every time after the router (Linksys EA2700) is powered off and restarted, there is no interent access available. The router configuration status reports an Internet Address of 0.0.0.0 and all the devices at home are left with a wifi without Internet access. I have to unplug the WAN from the router and plug it in again while it is turned on to restore internet access (and a normal Internet Address is seen from the status page). The WAN works fine with the routers I had previously. I wonder if I have to perform this every time I power on the router. Do you have any suggestions? I have tried resetting the router and reinstalling Cisco Connect but that didn't work.

    It would be best to isolate the concern by connecting a computer to the modem. Observe the performance of the modem’s internet connection within 24 hour. If there is nothing wrong with the modem’s performance then you now need to deal with the router. Make sure that the router’s firmware has been updated then reset the router after a firmware upgrade. If you have determined that the problem is really with the router then you might need to return the router and have it replaced.

  • How to set up the airport express with a linksys wireless-g broadband router

    I need to know if and how to set up an airport express to use to extend a home wi-fi network. I have AT&T service with a 2WIRE modem. I am using a Linksys wireless-G broadband router. I also have the new Macbook Air notebook. The airport express keeps giving me a blinking amber light even when the ethernet cable (from the modem) connected. Please let me know how to set up an extended wifi network using this system. Any help would be appreciated.

    If that is all that is done, the Express would not provide more wireless coverage.  Instead, it would duplicate the coverage provided by the Linksys and there would be two WiFi systems covering approximately the same area.  As per my above comment, one Express connects via Ethernet to the Linksys.  The second Express provides the extension.
    You must have misunderstood what I was saying.
    Linksys is providing a wireless network.
    The Express is connected to one of the LAN ports on the Linksys router using a long Ethernet cable (or Ethernet powerline adapters)
    The Express is located on the other side of the house, for example.
    The Express is configured to create a wireless network using the same wireless network name, security and password as the Linksys router
    The Express is configured in Bridge Mode
    This has worked quite well for me for years. Computers "switch" from one wireless access point to another smoothly and automatically while they move around the house.
    Although this is an "extended" network, it is technically known as a "roaming" network.
    This is what I was suggesting as a possible alternative without having to buy more hardware.

  • How to setup the Linksys router E4200 DD-WRT for WVC54GCA

    I don't know how to setup the Linksys router E4200 DD-WRT for WVC54GCA. The DD-WRT is very complcated. Please help!!!!! Also, I have used the TZO.com for the DDNS. Should I setup the DDNS for DD-WRT router??? I used the DDNS for my old model router before. Thanks.
    Solved!
    Go to Solution.

    Hi majekho, that is best be answered by support from the developers at the DD-WRT forums.
    The Search Function is your friend.... and Google too.
    How to Secure your Network
    How to Upgrade Routers Firmware
    Setting-Up a Router with DSL Internet Service
    Setting-Up a Router with Cable Internet Service
    How to Hard Reset or 30/30/30 your Router

  • I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

    I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

    RESET YOUR ROUTER
    No. Reset your router.

  • How to reconfigure the IIS with BPC 7.0  MS?

    Hi All,
    we are facing one problem; at first we had problem in IIS. so we reinstalled the IIS. now we are not able to BPC 7.0 application from the web. we are getting Http 404 error. how to reconfigure the osoft in IIS. what are the settings should be taken care?
    please help
    thnks in advance.
    regards,
    sakthi.

    Hello,
       If you have reinstall the IIS, it is better to reinstall BPC after, just to be sure you have the right settings.
    Best regards,
    Mihaela

  • Fieldpoint - How to reconfigured Field point hardware configuration

    Respected Sir,
    We are using labview version 5.1, operating system windows 95, FiledPoint explorer 1.6,
    I would kindly request all to please help to solve how to reconfigured Field point hardware, I am new learner of labVIEW.
    When i run Fieldpoint explorer 1.6, in labview 5.1 operating WINDOWS 95 version, i received one command as
    A value return from the server is out of the expected range.
    The FieldPoint hardware ranges need to be re configured, so they match the ranges saved in the configuration file.
    Go to each device configuration dialog and select channel configuration to synchronize the saved configuration with the hardware configuration.
    Thanking You
    Yours faithfully
    M.Viajy

    That is correct. There is no way to simulate a FieldPoint device. The suggested workaround should work well for you, however. Create some simulated VIs that perform the same task as the FieldPoint writes and reads (at least in terms of what inputs they accept or outputs they have), and place them in the other case in a Case Structure as the FieldPoint VIs.
    LabVIEW 8 takes these possibilities one step further with Conditional Disable Structures and Diagram Disable Structures. The difference between these two structures and a Case Structure is that code in the disabled cases doesn't even compile. This means you could even have broken wires or broken subVIs inside the disabled case, and you'd still be able to run your program. In the case of this FieldPoint application, you could use a Conditional Disable Structure that automatically polls the target OS type (Windows, Linux, Pharlap ETS, etc) and selectively compiles one case based on the target OS. This would allow you to seamlessly run VIs on your computer and FieldPoint without modifying any code. The other advantage is that the simulated FieldPoint code wouldn't get compiled when you target your real FieldPoint device, so you wouldn't increase your code size or memory usage unnecessarily for the final product.
    Message Edited by Jarrod S. on 04-24-2006 03:51 PM
    Jarrod S.
    National Instruments

  • I have airport extreme as my base, how do I use linksys as the extender

    I have airport extreme as my base, how do I use linksys as the extender

    You would need to connect the Linksys to the AirPort Extreme Base Station (AEBS) by Ethernet, and then, configure both of them for a roaming network.

  • How to reconfigure my audio interface

    Hi someone can tell me how to reconfigure my audio interface? is a motu 828 MKII Maverick 10.9.1 system I am thank you very much am using logic pro X

    Do a factory reset!
    to reset the 828:
    Turn the computer off
    - Unplug the firewire
    - press the button "setup", turn full
    - right until "factory default"
    - push select
    - confirm with "value"
    Turn the computer on, let it settle.
    - plug back firewire

  • How to reconfigure essbase

    Hi All,
    I installed essbase11.1.2 and configured it with oracle database.
    Currently configured oracle database is not available , so i want to reconfigure the essbase with another DB .
    Configuration utility shows error whenever i select the component to be configured and click next.
    As it is not able to connect with OLD oracle DB.
    How to reconfigure the essbase with new DB.
    Ayush

    No, I can't. In the configuration page, the 'Essbase Instance Name' is readonly. When I click 'Next', it complains about the instance name is already exists.
    I guess I need to remove the instance from the Shared Services Registry. But, don't know how.

  • How can I boost the range of my router?

    I have fios for phone/tv/Internet and use the Verizon MI24-WR router which works fine but my bedroom on the other side of the house doesn't get a signal. Any recommendation on improving the signal? I have the router in the office connected to the printer, PC and a"cable box" so moving the router would be a pain.
    I have an old Linksys WRT54G that I could use as a booster but have no idea how to do that.
    Does Verizon update router firmware? Replace older routers?

    Firmware updates should happen automatically - login to  your router and from here http:\\192.168.1.1
    - advanbced - firmware upgrade to verify what version you have. From what I read routers are replaced based on issues you are having as well as your speed tier (75 Mb/s and up get the latest router)
    I defer to the experts AFA extending the range of your WIFI please see http://forums.verizon.com/t5/Home-Networking/Actio​ntec-router-does-not-support-wireless-range-extend​...
    If a forum member gives an answer you like, please give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem. Thanks !!!
    http://forums.verizon.com/t5/Verizon-net-Email/Fix-for-Missing-Inbox-sent-folders-etc-with-Internet-Explorer-11/m-p/647399

  • HP Officejet Pro 8500a prints slowly over wireless on Cisco Linksys Smart Wi-Fi Router EA6500

    I have the HP Officejet Pro 8500a. I recenrly change my wiress router to the Cisco Linksys Smart Wi-Fi Router EA6500.
    Nearly every time I print, the documement remains "pending" for at least several minutes, sometimes as long as 20, until it finally starts printing. Once it starts printing, the document is printed quickly.
    It doesn't matter the size of the document and the time it remains "pending." I've done test pages with just the word "test" in a Microsoft Word document, and it will remain in "pending" for well over five minutes.
    If I print over the USB cord, there are no delays.
    I need help. I can't figure out how to remedy this long delay when printing wirelessly.
    On a side note in case this is helpful, the Linksys router does have a priority setting where you can select up to three devices for priority access (faster connection?), which seems to be more for bandwidth-intensive devices. I tried adding both the laptop I'm printing from and the printer to this priority list, but that did not improve the print connection speed.
    Advice please! Thank you.

    Hi Jim-Gr,
    I understand you have an Officejet 8500A that has started printing very slowly after switching routers. I'm sorry to hear this has happened but will certainly do my best to assist you.
    I appreciate you advising that you have tried connecting the printer via USB and it does make a huge difference. I'm also assuming your previous router didn't go this slowly either. With the things you have tried, my assumption is that it's a setting in the router that needs to be changed. If you're not sure how to change things in your router you can generally call the router company and they will walk you through it.
    First you will want to ask them if there are any firmware updates for your router, if there are have them perform the update. If it is up to date already then have them make sure your router is broadcasting at a frequency of 2.4 GHz as that's the only frequency the printer works with.
    Second, you will want to make sure the following ports are open:
    UDP: 427, 161, 137, 138
    TCP: 9100, 9220, 9500, 137, 139, 427
    Once all of this is updated, then I would suggest you power cycle everything (turn off the printer and the PC, pull the power on the router for 30 seconds and then turn the other two back on once lights are back to normal) and try again. This should allow your printing speed to go back to normal
    Hope this helps, have a great day!
    Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    **MissTeriLynn**
    I work on behalf of HP

  • Linksys WRT54G Wireless-G Router Not working

    I have a Linksys WRT54G Wireless-G Router and it has worked good for a couple months and yesterday it stopped. When I plug it in all the lights are lit even though there arent any ethernet cables connected and the power light blinks constantly. I tried holding the reset button on the back and it didnt help. Anyone know whats wrong or anything I can try to fix it?

    You need to try again to reset the router to factory defaults.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.

Maybe you are looking for